Jozefien De Keyzer
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Jozefien De Keyzer has a total of 51 co-authors. Here are the top co-authors by number of shared publications:
- Florian Wagner
KU Leuven - University of Leuven, Department of Mechanical Engineering, Leuven, Belgium; KU Leuven - University of Leuven, Department of Chemical Engineering, Diepenbeek, Belgium
5 shared publications Albert Van Bael
Materials Technology TC KU Leuven, Diepenbeek Campus Diepenbeek Belgium
4 shared publications- Albert Van Bael
Department of Materials Engineering, KU Leuven, Wetenschapspark 27—box 15152, 3590 Diepenbeek, Belgium
4 shared publications F. Desplentere
Materials Technology TC , KU Leuven, Bruges , Belgium
4 shared publicationsFrederik Desplentere
Materials Technology TC KU Leuven, Bruges Campus Leuven Belgium
4 shared publications- Gert‐Jan Bex
KU Leuven, Campus Diepenbeek, Materials Technology TC, Wetenschapspark 27 Diepenbeek 3590 Belgium
4 shared publications
Latest Publications
- 23 March 2020
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 137 (41)
Adhesion between ethylene‐propylene‐diene monomer and thermoplastics in two‐component injection molding: Effect of dicumylperoxide as curing agent
Strong adhesion at the interface is an important aspect in two‐component (2K) injection molding. It was therefore investigated whether dicumylperoxide (DCP) as curing agent in ethylene‐propylene‐diene monomer (EPDM) could stimulate interdiffusion and/or induce chemical bonding with thermoplastics. EPDM mixtures containing DCP concentrations between 2 to 8 parts per hundred rubber (phr) were combined with polar and non‐polar thermoplastics. Changes in EPDM physico‐mechanical bulk properties were analyzed, and the adhesion was evaluated by high temperature contact angle measurements and tensile testing. Results showed that DCP concentration did not influence EPDM‐thermoplastic compatibility. However, EPDM adhesion with polyethylene (PE) did improve when using up to 6 phr DCP (57% adhesion) as crosslinking is promoted. While with polypropylene (PP), adhesion linearly decreased (from 55% to 35% adhesion) with higher DCP concentrations due to prevailing scission reactions. Adhesion through chemical bonding with acrylonitrile‐butadiene‐styrene (ABS) caused better adhesion at 4 phr (43% adhesion) compared to polycarbonate (PC) at 4 phr (13% adhesion) where only limited interdiffusion occurs. Thus, selecting the optimal DCP concentration is highly important to boost adhesion between EPDM and thermoplastics. Furthermore, at these optimal DCP concentrations, physico‐mechanical properties require consideration as these properties were significantly affected.
- 23 March 2020
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 137 (41)
Adhesion between ethylene‐propylene‐diene monomer and thermoplastics in two‐component injection molding: Effect of dicumylperoxide as curing agent
Strong adhesion at the interface is an important aspect in two‐component (2K) injection molding. It was therefore investigated whether dicumylperoxide (DCP) as curing agent in ethylene‐propylene‐diene monomer (EPDM) could stimulate interdiffusion and/or induce chemical bonding with thermoplastics. EPDM mixtures containing DCP concentrations between 2 to 8 parts per hundred rubber (phr) were combined with polar and non‐polar thermoplastics. Changes in EPDM physico‐mechanical bulk properties were analyzed, and the adhesion was evaluated by high temperature contact angle measurements and tensile testing. Results showed that DCP concentration did not influence EPDM‐thermoplastic compatibility. However, EPDM adhesion with polyethylene (PE) did improve when using up to 6 phr DCP (57% adhesion) as crosslinking is promoted. While with polypropylene (PP), adhesion linearly decreased (from 55% to 35% adhesion) with higher DCP concentrations due to prevailing scission reactions. Adhesion through chemical bonding with acrylonitrile‐butadiene‐styrene (ABS) caused better adhesion at 4 phr (43% adhesion) compared to polycarbonate (PC) at 4 phr (13% adhesion) where only limited interdiffusion occurs. Thus, selecting the optimal DCP concentration is highly important to boost adhesion between EPDM and thermoplastics. Furthermore, at these optimal DCP concentrations, physico‐mechanical properties require consideration as these properties were significantly affected.
- Open Access
- 1 January 2020
- Published by Elsevier in Procedia CIRP
- Vol. 90, 416-420
Closed loop recycling of WEEE plastics: a case study for payment terminals
- 1 January 2020
- Published by Elsevier in Procedia CIRP
- Vol. 90, 416-420
Open AccessClosed loop recycling of WEEE plastics: a case study for payment terminals
- 1 December 2019
- Published by Elsevier in Waste Management
- Vol. 100, 269-277
Towards a more circular economy for WEEE plastics – Part A: Development of innovative recycling strategies
- 1 December 2019
- Published by Elsevier in Waste Management
- Vol. 100, 269-277
Towards a more circular economy for WEEE plastics – Part A: Development of innovative recycling strategies
- 20 August 2019
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 137 (9)
Effect of co‐agents on adhesion between peroxide cured ethylene–propylene–diene monomer and thermoplastics in two‐component injection molding
Two‐component (2K) injection‐molded products combining ethylene–propylene–diene monomer (EPDM) with polar or nonpolar thermoplastics require strong interfacial bonding. To optimize the adhesion, co‐agents trimethylolpropane trimethacrylate (TMPT) and triallyl cyanurate (TAC) are compared and concentrations were varied between 0 and 12 parts per hundred rubber (phr). Changes in material compatibility were characterized by contact angle measurements at high temperature, the adhesion was evaluated by tensile testing, and physicomechanical properties of the EPDM bulk were analyzed. Results show that with polypropylene, the adhesion increases to an optimum (3 phr TAC or 6 phr TMPT) independent of the co‐agent type, while for polyethylene only TAC (1.5 phr) effectively boosts adhesion. It is surmised that these optimal concentrations promote crosslinking reactions at the interface. For polycarbonate and acrylonitrile–butadiene–styrene, increasing TAC concentration causes higher adhesion due to improved compatibility. Furthermore, physicomechanical bulk properties change significantly with co‐agent concentrations, making the optimal curing composition application dependent. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020, 137, 48414.
- 20 August 2019
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 137 (9)
Effect of co‐agents on adhesion between peroxide cured ethylene–propylene–diene monomer and thermoplastics in two‐component injection molding
Two‐component (2K) injection‐molded products combining ethylene–propylene–diene monomer (EPDM) with polar or nonpolar thermoplastics require strong interfacial bonding. To optimize the adhesion, co‐agents trimethylolpropane trimethacrylate (TMPT) and triallyl cyanurate (TAC) are compared and concentrations were varied between 0 and 12 parts per hundred rubber (phr). Changes in material compatibility were characterized by contact angle measurements at high temperature, the adhesion was evaluated by tensile testing, and physicomechanical properties of the EPDM bulk were analyzed. Results show that with polypropylene, the adhesion increases to an optimum (3 phr TAC or 6 phr TMPT) independent of the co‐agent type, while for polyethylene only TAC (1.5 phr) effectively boosts adhesion. It is surmised that these optimal concentrations promote crosslinking reactions at the interface. For polycarbonate and acrylonitrile–butadiene–styrene, increasing TAC concentration causes higher adhesion due to improved compatibility. Furthermore, physicomechanical bulk properties change significantly with co‐agent concentrations, making the optimal curing composition application dependent. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020, 137, 48414.
- Open Access
- 1 August 2019
- Published by Walter de Gruyter GmbH in International Polymer Processing
- Vol. 34 (4) , 398-407
The Influence of Mechanical Recycling on Properties in Injection Molding of Fiber-Reinforced Polypropylene
Due to higher mechanical demands on technical parts, the application of short fiber reinforced thermoplastics for injection molding is strongly increasing. Therefore, more attention needs to be paid to the optimization of their recycling processes. Mechanical shredding of thermoplastics into granules is a common recycling method within polymer industries. The breaking of polymer chains and reinforcing fibers during this process may affect the material properties. This study presents the effect of ten recycling sequences on four different materials: polypropylene, glass fiber filled polypropylene, carbon fiber filled polypropylene and flax fiber filled polypropylene. Tests indicate that recycling has a negative influence on most of the mechanical properties. Polypropylene without fibers forms an exception as it does not exhibit any significant change in material properties. Glass fiber and carbon fiber reinforced polypropylene show a decrease in stiffness and tensile strength during the recycling steps. The impact strength of carbon and flax fiber reinforced polypropylene increases whereas that of glass fiber reinforced polypropylene decreases.
- 1 August 2019
- Published by Walter de Gruyter GmbH in International Polymer Processing
- Vol. 34 (4) , 398-407
Open AccessThe Influence of Mechanical Recycling on Properties in Injection Molding of Fiber-Reinforced Polypropylene
Due to higher mechanical demands on technical parts, the application of short fiber reinforced thermoplastics for injection molding is strongly increasing. Therefore, more attention needs to be paid to the optimization of their recycling processes. Mechanical shredding of thermoplastics into granules is a common recycling method within polymer industries. The breaking of polymer chains and reinforcing fibers during this process may affect the material properties. This study presents the effect of ten recycling sequences on four different materials: polypropylene, glass fiber filled polypropylene, carbon fiber filled polypropylene and flax fiber filled polypropylene. Tests indicate that recycling has a negative influence on most of the mechanical properties. Polypropylene without fibers forms an exception as it does not exhibit any significant change in material properties. Glass fiber and carbon fiber reinforced polypropylene show a decrease in stiffness and tensile strength during the recycling steps. The impact strength of carbon and flax fiber reinforced polypropylene increases whereas that of glass fiber reinforced polypropylene decreases.
- 1 August 2019
- Published by Elsevier in Waste Management
- Vol. 96, 206-214
Towards a more circular economy for WEEE plastics – Part B: Assessment of the technical feasibility of recycling strategies
- 1 August 2019
- Published by Elsevier in Waste Management
- Vol. 96, 206-214
Towards a more circular economy for WEEE plastics – Part B: Assessment of the technical feasibility of recycling strategies
- 13 June 2019
- Published by Wiley in Polymer Engineering & Science
- Vol. 59 (7) , 1489-1498
Prediction of interfacial strength of HDPE overmolded with EPDM
Multicomponent injection molding often combines a stiff thermoplastic material with a thermoplastic elastomer or thermoplastic vulcanite. Recently, for high‐demanding applications, a novel process has been developed to replace these thermoplastic elastomers or vulcanite with a thermoset rubber, for example, NBR or EPDM. One of the most important properties of a two component product is an adequate adhesion between both components. This paper describes a method, which combines experiments and numerical simulations to predict the adhesion strength between a thermoplastic, semicrystalline HDPE, and an EPDM thermoset rubber. This method uses numerical simulations of the interfacial temperature and the local degree of cure. The local interface temperature is combined with the results of DSC measurements to predict the degree of melting, subsequently linked to the ability to develop adhesive strength. The degree of cure is used to determine the local rubber strength. The combination of the given data will be used to predict interfacial strength. The results obtained by proposed numerical strategy have been successfully validated with experimental data on a simple plate product. POLYM. ENG. SCI., 59:1489–1498 2019. © 2019 Society of Plastics Engineers
- 13 June 2019
- Published by Wiley in Polymer Engineering & Science
- Vol. 59 (7) , 1489-1498
Prediction of interfacial strength of HDPE overmolded with EPDM
Multicomponent injection molding often combines a stiff thermoplastic material with a thermoplastic elastomer or thermoplastic vulcanite. Recently, for high‐demanding applications, a novel process has been developed to replace these thermoplastic elastomers or vulcanite with a thermoset rubber, for example, NBR or EPDM. One of the most important properties of a two component product is an adequate adhesion between both components. This paper describes a method, which combines experiments and numerical simulations to predict the adhesion strength between a thermoplastic, semicrystalline HDPE, and an EPDM thermoset rubber. This method uses numerical simulations of the interfacial temperature and the local degree of cure. The local interface temperature is combined with the results of DSC measurements to predict the degree of melting, subsequently linked to the ability to develop adhesive strength. The degree of cure is used to determine the local rubber strength. The combination of the given data will be used to predict interfacial strength. The results obtained by proposed numerical strategy have been successfully validated with experimental data on a simple plate product. POLYM. ENG. SCI., 59:1489–1498 2019. © 2019 Society of Plastics Engineers
- 1 April 2019
- Published by Wiley in Macromolecular Symposia
- Vol. 384 (1)
Influence of Label Impurities in Recycling on the Mechanical Properties of PC/ABS Materials
The current share of plastic in waste electrical and electronic equipment (WEEE) is considerable approximately 25%. This potential should be used by recycling to create economic, environmental and financial benefits. In order to investigate the influence of potential label impurities that can occur as contaminations in recycled plastics, a testing series based on controlled contamination and shredding of virgin polycarbonate (PC)/acrylonitrile–butadiene–styrene (ABS) was developed. PC/ABS granules and paper labels as well as two different types of polypropylene (PP1 and PP2) in different concentrations were stepwise processed and injection moulded into specimens. The influence of the three different impurities and their concentrations on the mechanical properties of the plastic were investigated.
- 1 April 2019
- Published by Wiley in Macromolecular Symposia
- Vol. 384 (1)
Influence of Label Impurities in Recycling on the Mechanical Properties of PC/ABS Materials
The current share of plastic in waste electrical and electronic equipment (WEEE) is considerable approximately 25%. This potential should be used by recycling to create economic, environmental and financial benefits. In order to investigate the influence of potential label impurities that can occur as contaminations in recycled plastics, a testing series based on controlled contamination and shredding of virgin polycarbonate (PC)/acrylonitrile–butadiene–styrene (ABS) was developed. PC/ABS granules and paper labels as well as two different types of polypropylene (PP1 and PP2) in different concentrations were stepwise processed and injection moulded into specimens. The influence of the three different impurities and their concentrations on the mechanical properties of the plastic were investigated.
- Open Access
- 22 January 2019
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2055 (1) , 070017
Experimental analysis of conformal cooling in SLM produced injection moulds: Effects on process and product quality
In an injection moulding process, the cooling step takes up to 50% or more of the total cycle time. Therefore, any reduction of the cooling time directly results into an increase of the production rate. Furthermore, products are often rejected because of defects such as warpage or sink marks. The cause of these defects is often an unevenly distributed cooling in the mould due to complex product or mould shapes. A solution for both problems is Conformal Cooling, a technique in which the cooling channels are designed to follow the contour of the mould cavity to obtain an optimal cooling. These often curved cooling channels are difficult or even impossible to produce with conventional techniques such as milling, drilling and EDM. The recent development of the Selective Laser Melting (SLM) 3D printing technology can be used to overcome these limitations. In a previous work [1] the cooling channels of an existing mould to produce sorting trays were assessed and redesigned to achieve a conformal cooled mould. A mould cavity and insert were provided with these cooling channels by means of the SLM technique. In this work the performance of the conformal cooled mould is compared with the original mould based on process characteristics and product measurements. In particular the start-up losses, mould temperature during the cycle, cycle time and product warpage are assessed.
- 22 January 2019
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2055 (1) , 070017
Open AccessExperimental analysis of conformal cooling in SLM produced injection moulds: Effects on process and product quality
In an injection moulding process, the cooling step takes up to 50% or more of the total cycle time. Therefore, any reduction of the cooling time directly results into an increase of the production rate. Furthermore, products are often rejected because of defects such as warpage or sink marks. The cause of these defects is often an unevenly distributed cooling in the mould due to complex product or mould shapes. A solution for both problems is Conformal Cooling, a technique in which the cooling channels are designed to follow the contour of the mould cavity to obtain an optimal cooling. These often curved cooling channels are difficult or even impossible to produce with conventional techniques such as milling, drilling and EDM. The recent development of the Selective Laser Melting (SLM) 3D printing technology can be used to overcome these limitations. In a previous work [1] the cooling channels of an existing mould to produce sorting trays were assessed and redesigned to achieve a conformal cooled mould. A mould cavity and insert were provided with these cooling channels by means of the SLM technique. In this work the performance of the conformal cooled mould is compared with the original mould based on process characteristics and product measurements. In particular the start-up losses, mould temperature during the cycle, cycle time and product warpage are assessed.