Sangsig Yun
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Sangsig Yun has a total of 61 co-authors. Here are the top co-authors by number of shared publications:
- Zekai Hong
Aerospace Research Center, National Research Council of Canada , 1200 Montreal Road, Ottawa, ON K1A 0R6, Canada
5 shared publications Robert B. Walker
National Research Council Canada (Canada)
4 shared publicationsStephen J. Mihailov
National Research Council Canada (Canada)
4 shared publicationsDavid Coulas
National Research Council Canada (Canada)
3 shared publicationsHuimin Ding
National Research Council Canada (Canada)
3 shared publicationsJoan Boulanger
National Research Council Canada, Ottawa, ON, Canada
3 shared publications
Latest Publications
- 29 January 2025
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 147 (7) , 1-11
An Investigation of a Multi-Injector, Premix/Micromix Burner Burning Pure Methane to Pure Hydrogen
Micromix combustion technology has been identified as a promising strategy to mitigate the risks associated with burning high-hydrogen-content fuels. This technology has recently been introduced in premixed injector designs to develop burners with broader fuel flexibility, allowing the combustion of fuels ranging from natural gas, or currently available hydrocarbons, to pure hydrogen by controlling the micromix fuel ratio (MFR). Modifying this additional operating parameter can lead to premixed, partially premixed, and micromixed combustion, each having different stability mechanisms. The combustion characteristics of such flames in an industrial combustion environment with hundreds of injectors are unknown. A multi-injector configuration, consisting of five (5) injectors placed in a cross pattern, is used to investigate the combustion of pure methane to pure hydrogen, and different blends. Stability and combustion dynamic maps are first obtained at atmospheric temperature and pressure for fuel-lean mixtures of H2/CH4 ranging from 0/100%, 70/30%, 90/10%, to 100/0%, by volume. For each fuel mixture, the equivalence ratio is adjusted to maintain the same adiabatic flame temperature throughout the experiments. An increase in blowoff (BO) limit is observed for the multi-injector array compared to a single nozzle, while flashback occurs more rapidly for dominantly premixed conditions with high-hydrogen-content fuel. In addition to extending the flashback limit, micromixed flames are generally quieter for high-hydrogen-content fuels. Laser diagnostics are performed on selected operating conditions with hydrogen content of 0%, 30%, 50%, 70%, 90%, and 100%. Eight cases are investigated in this work at a constant bulk inlet velocity to highlight the impact of hydrogen content and MFR on the flame shape. Two-dimensional (2D) particle image velocimetry (PIV), OH and acetone planar laser-induced fluorescence (PLIF), as well as acoustic measurements are performed simultaneously. The planar measurements show that the OH-PLIF signal becomes thinner and nonaxisymmetric as MFR is increased from 0% to 100%, with the flames gradually transitioning from V-shaped to M-shaped, before stabilizing as jet flames in crossflow.
- 29 January 2025
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 147 (7) , 1-11
An Investigation of a Multi-Injector, Premix/Micromix Burner Burning Pure Methane to Pure Hydrogen
Micromix combustion technology has been identified as a promising strategy to mitigate the risks associated with burning high-hydrogen-content fuels. This technology has recently been introduced in premixed injector designs to develop burners with broader fuel flexibility, allowing the combustion of fuels ranging from natural gas, or currently available hydrocarbons, to pure hydrogen by controlling the micromix fuel ratio (MFR). Modifying this additional operating parameter can lead to premixed, partially premixed, and micromixed combustion, each having different stability mechanisms. The combustion characteristics of such flames in an industrial combustion environment with hundreds of injectors are unknown. A multi-injector configuration, consisting of five (5) injectors placed in a cross pattern, is used to investigate the combustion of pure methane to pure hydrogen, and different blends. Stability and combustion dynamic maps are first obtained at atmospheric temperature and pressure for fuel-lean mixtures of H2/CH4 ranging from 0/100%, 70/30%, 90/10%, to 100/0%, by volume. For each fuel mixture, the equivalence ratio is adjusted to maintain the same adiabatic flame temperature throughout the experiments. An increase in blowoff (BO) limit is observed for the multi-injector array compared to a single nozzle, while flashback occurs more rapidly for dominantly premixed conditions with high-hydrogen-content fuel. In addition to extending the flashback limit, micromixed flames are generally quieter for high-hydrogen-content fuels. Laser diagnostics are performed on selected operating conditions with hydrogen content of 0%, 30%, 50%, 70%, 90%, and 100%. Eight cases are investigated in this work at a constant bulk inlet velocity to highlight the impact of hydrogen content and MFR on the flame shape. Two-dimensional (2D) particle image velocimetry (PIV), OH and acetone planar laser-induced fluorescence (PLIF), as well as acoustic measurements are performed simultaneously. The planar measurements show that the OH-PLIF signal becomes thinner and nonaxisymmetric as MFR is increased from 0% to 100%, with the flames gradually transitioning from V-shaped to M-shaped, before stabilizing as jet flames in crossflow.
- Open Access
- 8 November 2024
- Published by Cambridge University Press (CUP) in The Aeronautical Journal
- Vol. 129 (1331) , 63-83
Isolating influences of varying pitch from the effects of non-zero compound angles on effusion cooling
Effusion cooling is the state-of-the-art cooling technology for gas turbine hot-gas path components. Typically, effusion cooling holes across the entire combustor liner are aligned with the combustor axis, rendering a nominal zero compound angle between highly directional miniature effusion cooling jets and the main flow direction. The pitch of effusion cooling holes is optimised accordingly. However, the swirling main flow results in a non-zero compound angle and an effectively different pitch from the design. The directional effect of effusion cooling as a result of swirling main flow on the adiabatic film cooling effectiveness (AFE) is a combined effect of a non-zero compound angle and a varied pitch. The current experimental study aims to investigate the isolated effects of compound angle on AFE by excluding the influences of varying pitch. With an improved understanding of the sole effects of non-zero compound angles on AFE, the roles that a varied pitch plays in modifying AFE are further discussed to guide future effusion cooling designs under swirling main flow conditions. Binary pressure sensitive paint (PSP) was used to determine AFE experimentally.
- 8 November 2024
- Published by Cambridge University Press (CUP) in The Aeronautical Journal
- Vol. 129 (1331) , 63-83
Open AccessIsolating influences of varying pitch from the effects of non-zero compound angles on effusion cooling
Effusion cooling is the state-of-the-art cooling technology for gas turbine hot-gas path components. Typically, effusion cooling holes across the entire combustor liner are aligned with the combustor axis, rendering a nominal zero compound angle between highly directional miniature effusion cooling jets and the main flow direction. The pitch of effusion cooling holes is optimised accordingly. However, the swirling main flow results in a non-zero compound angle and an effectively different pitch from the design. The directional effect of effusion cooling as a result of swirling main flow on the adiabatic film cooling effectiveness (AFE) is a combined effect of a non-zero compound angle and a varied pitch. The current experimental study aims to investigate the isolated effects of compound angle on AFE by excluding the influences of varying pitch. With an improved understanding of the sole effects of non-zero compound angles on AFE, the roles that a varied pitch plays in modifying AFE are further discussed to guide future effusion cooling designs under swirling main flow conditions. Binary pressure sensitive paint (PSP) was used to determine AFE experimentally.
- 15 October 2024
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 147 (3) , 1-31
A Large Eddy Simulation Study on Hydrogen Microjets in Hot Vitiated Crossflow
In this paper, the results of a large eddy simulation (LES) study on hydrogen microjets (dj ~ 0.5 mm) injected into a hot (1600 K) vitiated crossflow at different angles?namely, normal (90°) and inclined jet (30°), are presented. The goal is to explore the effects of injection angle on coherent turbulent structure formations, flame-vortex interactions, and wall heat flux contributions. The LES identifies the presence of the horseshoe vortex, the shear layer vortices (SLV), and the counter-rotating vortex pair (CVP), along with the shedding of spanwise-symmetry hairpin vortices in both the normal and inclined jets. The structures in the latter, however, appear more convoluted. In the near field, SLV-induced flow is crucial for mixing and flame propagation on the windward side of the jet, stabilized by autoignition near the jet exits. A flame-shear layer offset is observed here. In the far field, CVP dominates hot vitiated crossflow entrainment, driving flame propagation and heat and species transfer to the leeward side near the injection wall. In the wake region, combustion remains closer to the normal jet exit due to a stronger recirculation zone, resulting in higher wall heat fluxes. The mean wall heat flux values of both the normal and inclined jets decrease and approach each other with moving away from the jet exit in the streamwise direction. The present LES study results are compared to experimental data from the literature by considering instantaneous hydroxide (OH) fields and mean wall heat fluxes.
- 15 October 2024
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 147 (3) , 1-31
A Large Eddy Simulation Study on Hydrogen Microjets in Hot Vitiated Crossflow
In this paper, the results of a large eddy simulation (LES) study on hydrogen microjets (dj ~ 0.5 mm) injected into a hot (1600 K) vitiated crossflow at different angles?namely, normal (90°) and inclined jet (30°), are presented. The goal is to explore the effects of injection angle on coherent turbulent structure formations, flame-vortex interactions, and wall heat flux contributions. The LES identifies the presence of the horseshoe vortex, the shear layer vortices (SLV), and the counter-rotating vortex pair (CVP), along with the shedding of spanwise-symmetry hairpin vortices in both the normal and inclined jets. The structures in the latter, however, appear more convoluted. In the near field, SLV-induced flow is crucial for mixing and flame propagation on the windward side of the jet, stabilized by autoignition near the jet exits. A flame-shear layer offset is observed here. In the far field, CVP dominates hot vitiated crossflow entrainment, driving flame propagation and heat and species transfer to the leeward side near the injection wall. In the wake region, combustion remains closer to the normal jet exit due to a stronger recirculation zone, resulting in higher wall heat fluxes. The mean wall heat flux values of both the normal and inclined jets decrease and approach each other with moving away from the jet exit in the streamwise direction. The present LES study results are compared to experimental data from the literature by considering instantaneous hydroxide (OH) fields and mean wall heat fluxes.
- 1 July 2024
- Published by Cambridge University Press (CUP) in The Aeronautical Journal
- Vol. 128 (1325) , 1429-1449
Combustion characteristics of sustainable aviation fuels in a scaled-down afterburner test rig
This study investigates the combustion characteristics (lean blowoff (LBO), flashback, and combustion instability) of sustainable aviation fuels (SAFs) using a two-staged combustor arranged in tandem. The combustor consists of a first (main) burner with an axial swirler and a second burner (afterburner) with a V-gutter bluff-body. The main burner utilises a constant flow rate of CH4/Air as reactants, while the afterburner operates on the combustion product from the first burner, additional dilution air, and one of the six liquid test fuels (Jet-A, A-2, C-1, C-5, C-9, and JP-8/HRJ) as reactants. When test fuels with higher derived cetane number (DCN) are used in the afterburner, it is observed that LBO occurs at lower afterburner global equivalence ratios ( ${\phi _{af}}$ ). This is due to the smaller chemical time scale of those test fuels, which enables the flame to be sustained under higher flow speeds. This is consistent with the results of previous studies. Additionally, this study shows that flashback also occurs at lower equivalence ratio for test fuels with higher DCN. This is a new finding and can be explained in a similar way to LBO. As the operating conditions approach the LBO or exceed flashback limits, the reactivity of shear layer also decreases, creating favourable conditions for them to occur. Moreover, for test fuels with low DCN (C-1 and C-5), blowoff occurs instead of flashback as ${\phi _{af}}$ increases. This can be attributed to the stronger pressure perturbation resulting from combustion instability in these flames compared to others. It demonstrates a stronger correlation between the pressure perturbation and the heat release rate fluctuation for C-1 and C-5 than that of other test fuels at the same equivalence ratio. In conclusion, it was found that test fuels with higher DCN have advantages in terms of LBO and stability, however, they are more prone to flashback.- 1 July 2024
- Published by Cambridge University Press (CUP) in The Aeronautical Journal
- Vol. 128 (1325) , 1429-1449
Combustion characteristics of sustainable aviation fuels in a scaled-down afterburner test rig
This study investigates the combustion characteristics (lean blowoff (LBO), flashback, and combustion instability) of sustainable aviation fuels (SAFs) using a two-staged combustor arranged in tandem. The combustor consists of a first (main) burner with an axial swirler and a second burner (afterburner) with a V-gutter bluff-body. The main burner utilises a constant flow rate of CH4/Air as reactants, while the afterburner operates on the combustion product from the first burner, additional dilution air, and one of the six liquid test fuels (Jet-A, A-2, C-1, C-5, C-9, and JP-8/HRJ) as reactants. When test fuels with higher derived cetane number (DCN) are used in the afterburner, it is observed that LBO occurs at lower afterburner global equivalence ratios ( ${\phi _{af}}$ ). This is due to the smaller chemical time scale of those test fuels, which enables the flame to be sustained under higher flow speeds. This is consistent with the results of previous studies. Additionally, this study shows that flashback also occurs at lower equivalence ratio for test fuels with higher DCN. This is a new finding and can be explained in a similar way to LBO. As the operating conditions approach the LBO or exceed flashback limits, the reactivity of shear layer also decreases, creating favourable conditions for them to occur. Moreover, for test fuels with low DCN (C-1 and C-5), blowoff occurs instead of flashback as ${\phi _{af}}$ increases. This can be attributed to the stronger pressure perturbation resulting from combustion instability in these flames compared to others. It demonstrates a stronger correlation between the pressure perturbation and the heat release rate fluctuation for C-1 and C-5 than that of other test fuels at the same equivalence ratio. In conclusion, it was found that test fuels with higher DCN have advantages in terms of LBO and stability, however, they are more prone to flashback.- 11 December 2023
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 146 (5) , 1-12
Characterization of a Novel Additive Manufacturing Micromix Nozzle Burning Methane to Hydrogen
As the energy landscape transitions to low/zero-carbon fuels, gas turbine manufacturers are targeting fuel flexible operation with natural gas, syngas, and hydrogen-enriched mixtures. Having a single geometry that can support the different fuel blends requested by clients can accelerate the transition to cleaner energy generation and mitigate the environmental impact of gas turbines. Toward this goal, micromix combustion technology has received significant interest, and when coupled with additive manufacturing, novel injector geometries with unique configurations may be capable of stabilizing premixed, partially-premixed, and diffusion flames using fuel mixtures ranging from pure methane to pure hydrogen. In this work, a preliminary investigation of this micromix concept is performed in the Atmospheric Combustion Rig at the National Research Council (NRC) Canada. Flame stability maps are obtained for fuel lean mixtures of H2/CH4 ranging from 0/100, 70/30, 90/10, to 100/0%, by volume. Multiple flame shapes are observed depending on the fuel mixture and combustion mode selected. Particle image velocimetry (PIV), OH, and acetone planar laser-induced fluorescence (PLIF), and acoustic measurements provide additional insights into the combustion process of these novel burners to better understand the stability mechanisms. The quality of the fuel–air mixing from the premixed and micromix injectors is assessed using acetone as a tracer for the fuel, while simultaneous OH-PLIF measurements provide an indication of the postflame regions in the flow. Acoustic measurements complete the current dataset and provide combustion dynamics maps measuring the normalized pressure amplitudes and identifying the dominant frequencies. The preliminary characterization of this additive manufacturing (AM) micromix nozzle shows promising fuel flexibility with wide stability margins and low combustion dynamics for this single nozzle burner.
- 11 December 2023
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 146 (5) , 1-12
Characterization of a Novel Additive Manufacturing Micromix Nozzle Burning Methane to Hydrogen
As the energy landscape transitions to low/zero-carbon fuels, gas turbine manufacturers are targeting fuel flexible operation with natural gas, syngas, and hydrogen-enriched mixtures. Having a single geometry that can support the different fuel blends requested by clients can accelerate the transition to cleaner energy generation and mitigate the environmental impact of gas turbines. Toward this goal, micromix combustion technology has received significant interest, and when coupled with additive manufacturing, novel injector geometries with unique configurations may be capable of stabilizing premixed, partially-premixed, and diffusion flames using fuel mixtures ranging from pure methane to pure hydrogen. In this work, a preliminary investigation of this micromix concept is performed in the Atmospheric Combustion Rig at the National Research Council (NRC) Canada. Flame stability maps are obtained for fuel lean mixtures of H2/CH4 ranging from 0/100, 70/30, 90/10, to 100/0%, by volume. Multiple flame shapes are observed depending on the fuel mixture and combustion mode selected. Particle image velocimetry (PIV), OH, and acetone planar laser-induced fluorescence (PLIF), and acoustic measurements provide additional insights into the combustion process of these novel burners to better understand the stability mechanisms. The quality of the fuel–air mixing from the premixed and micromix injectors is assessed using acetone as a tracer for the fuel, while simultaneous OH-PLIF measurements provide an indication of the postflame regions in the flow. Acoustic measurements complete the current dataset and provide combustion dynamics maps measuring the normalized pressure amplitudes and identifying the dominant frequencies. The preliminary characterization of this additive manufacturing (AM) micromix nozzle shows promising fuel flexibility with wide stability margins and low combustion dynamics for this single nozzle burner.
- 20 September 2022
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 144 (11)
Spray Characterization of a Preheated Bio-Oil Surrogate at Elevated Pressures
Atomization plays an important role in the gasification or combustion of bio-oils, where the atomizer parameters need to be properly controlled to efficiently atomize a highly viscous liquid at elevated pressures with imparting the least amount of kinetic energy to the discharged droplets because of evaporation and chemical reaction constraints. With a focus on bio-oil deployments in microgas turbines (MGTs), an aqueous surrogate of a preheated bio-oil, injected from an original equipment manufacturer (OEM) twin-fluid atomizer, is used in the present study for spray size and velocity measurements at elevated pressures. The experiments were conducted in High Pressure Spray Facility of the National Research Council of Canada (NRC) using various optical diagnostics including laser sheet imaging (LSI), phase Doppler anemometry (PDA), and laser diffraction (LD). A scaling strategy was adopted to conserve the ranges of gas-to-liquid momentum flux ratio, M, at different working pressures, P. Over the range of conditions studied, it is found out that the cone angle of sprays is insensitive to P, but they decrease with increasing M. For a constant value of M, droplet mean diameters increase and their corresponding velocities decrease with increasing P, attributed to the effect of gas-to-liquid density ratio on the primary breakup of a liquid jet in a coaxial gas stream. Therefore, to estimate the Sauter mean diameter of spray droplets, D32, a correlation previously reported in the literature is modified by including the effect of system air density at elevated pressures, and a novel correlation is proposed based on four dimensionless groups, namely, gas Weber number and gas-to-liquid momentum flux ratio, density ratio, and viscosity ratio. The detailed results obtained in the present study could be used to define the optimal parameters required for twin-fluid atomization of high viscosity liquids with various atomization gases under realistic operating conditions and to enhance the capabilities of their numerical simulations.
- 20 September 2022
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 144 (11)
Spray Characterization of a Preheated Bio-Oil Surrogate at Elevated Pressures
Atomization plays an important role in the gasification or combustion of bio-oils, where the atomizer parameters need to be properly controlled to efficiently atomize a highly viscous liquid at elevated pressures with imparting the least amount of kinetic energy to the discharged droplets because of evaporation and chemical reaction constraints. With a focus on bio-oil deployments in microgas turbines (MGTs), an aqueous surrogate of a preheated bio-oil, injected from an original equipment manufacturer (OEM) twin-fluid atomizer, is used in the present study for spray size and velocity measurements at elevated pressures. The experiments were conducted in High Pressure Spray Facility of the National Research Council of Canada (NRC) using various optical diagnostics including laser sheet imaging (LSI), phase Doppler anemometry (PDA), and laser diffraction (LD). A scaling strategy was adopted to conserve the ranges of gas-to-liquid momentum flux ratio, M, at different working pressures, P. Over the range of conditions studied, it is found out that the cone angle of sprays is insensitive to P, but they decrease with increasing M. For a constant value of M, droplet mean diameters increase and their corresponding velocities decrease with increasing P, attributed to the effect of gas-to-liquid density ratio on the primary breakup of a liquid jet in a coaxial gas stream. Therefore, to estimate the Sauter mean diameter of spray droplets, D32, a correlation previously reported in the literature is modified by including the effect of system air density at elevated pressures, and a novel correlation is proposed based on four dimensionless groups, namely, gas Weber number and gas-to-liquid momentum flux ratio, density ratio, and viscosity ratio. The detailed results obtained in the present study could be used to define the optimal parameters required for twin-fluid atomization of high viscosity liquids with various atomization gases under realistic operating conditions and to enhance the capabilities of their numerical simulations.
- Open Access
- 4 December 2020
- Published by Global Power and Propulsion Society in Journal of the Global Power and Propulsion Society
- Vol. 4, 202-216
Experimental Evaluation of Using Silica Aerogels as the Thermal Insulator for Combustor Liners
An experimental study was conducted for evaluating the feasibility of using silica aerogel as thermal insulator for combustor liners. Aerogels are a superior material for minimizing heat flux to the metal structure of the combustion liner due to their low thermal conductivity. In this study, a...
- 4 December 2020
- Published by Global Power and Propulsion Society in Journal of the Global Power and Propulsion Society
- Vol. 4, 202-216
Open AccessExperimental Evaluation of Using Silica Aerogels as the Thermal Insulator for Combustor Liners
An experimental study was conducted for evaluating the feasibility of using silica aerogel as thermal insulator for combustor liners. Aerogels are a superior material for minimizing heat flux to the metal structure of the combustion liner due to their low thermal conductivity. In this study, a...
- 1 September 2020
- Published by Elsevier in Energy Conversion and Management
- Vol. 220
Breakup mechanisms in air-assisted atomization of highly viscous pyrolysis oils
- 1 September 2020
- Published by Elsevier in Energy Conversion and Management
- Vol. 220
Breakup mechanisms in air-assisted atomization of highly viscous pyrolysis oils
- 17 June 2019
- Published by ASME International
Evaluation of Spray Performance of Pyrolysis Oil
Pyrolysis oil has become an important subject of research as it is considered to be a potential environmentally friendly and cheap alternative to conventional fossil fuels. Unfortunately, due to the significant differences of the chemical and physical properties of pyrolysis oil than that of fossil fuels, the deployment of pyrolysis oil in existing power systems such as gas turbines and internal combustion engines has been highly restricted. Thus, major research on pyrolysis oil has been conducted to overcome these challenges related to the unfavorable physical and chemical properties of pyrolysis oil. This paper reports experimental work on the effects of physical properties of the pyrolysis oil on spray performance of nozzles. Effort to evaluate the spray performance by using different types of atomizers has been made as well. Laser based diagnostics was applied to obtain qualitative comparisons spray characteristics of various pyrolysis oils. Experimental data such as the distribution of fuel droplet sizes and overall spray shapes was analyzed, which could provide valuable guidelines to design fuel nozzles. Lastly, the paper will also present NRC’s plans to accelerate the deployment of such pyrolysis oils in industrial gas turbines.
- 17 June 2019
- Published by ASME International
Evaluation of Spray Performance of Pyrolysis Oil
Pyrolysis oil has become an important subject of research as it is considered to be a potential environmentally friendly and cheap alternative to conventional fossil fuels. Unfortunately, due to the significant differences of the chemical and physical properties of pyrolysis oil than that of fossil fuels, the deployment of pyrolysis oil in existing power systems such as gas turbines and internal combustion engines has been highly restricted. Thus, major research on pyrolysis oil has been conducted to overcome these challenges related to the unfavorable physical and chemical properties of pyrolysis oil. This paper reports experimental work on the effects of physical properties of the pyrolysis oil on spray performance of nozzles. Effort to evaluate the spray performance by using different types of atomizers has been made as well. Laser based diagnostics was applied to obtain qualitative comparisons spray characteristics of various pyrolysis oils. Experimental data such as the distribution of fuel droplet sizes and overall spray shapes was analyzed, which could provide valuable guidelines to design fuel nozzles. Lastly, the paper will also present NRC’s plans to accelerate the deployment of such pyrolysis oils in industrial gas turbines.
- 14 May 2018
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10654, 1065408
High temperature measurement of a low emission, high pressure combustor using femtosecond laser written fiber Bragg gratings
Femtosecond Infrared (fs-IR) laser written fiber Bragg gratings (FBGs), have shown great potential for sensing in extreme environments. This paper presents the fabrication and deployment of two fs-IR laser written FBG temperature probes, for monitoring temperature gradients on the flame tube of a low emission burner, during a high pressure combustor test of an optically accessible combustor rig (OACR). Results of this work include: contour plots of measured internal and exhaust temperature gradients, contrast of FBG measurements with thermocouple data, discussion of deployment strategies, as well as comments on reliability and other important considerations.
- 14 May 2018
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10654, 1065408
High temperature measurement of a low emission, high pressure combustor using femtosecond laser written fiber Bragg gratings
Femtosecond Infrared (fs-IR) laser written fiber Bragg gratings (FBGs), have shown great potential for sensing in extreme environments. This paper presents the fabrication and deployment of two fs-IR laser written FBG temperature probes, for monitoring temperature gradients on the flame tube of a low emission burner, during a high pressure combustor test of an optically accessible combustor rig (OACR). Results of this work include: contour plots of measured internal and exhaust temperature gradients, contrast of FBG measurements with thermocouple data, discussion of deployment strategies, as well as comments on reliability and other important considerations.