KAKenji Aoki

Kenji Aoki

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Kenji Aoki has a total of 42 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Compressive behavior of wood contact with mortar and epoxy resin adhesives

    by Shun Kosugi, Marina Totsuka, Hiroki Nakashima, Masakazu Ikeda, Kenji Aoki

    In recent years, researchers and engineers have developed a wide range of connection systems between wood and other materials, such as concrete and steel. However, the mechanical behavior of the surfaces where wood meets these materials is yet to be understood. In wood, low-stiffness areas called damage zones form near end grains, when compressed parallel to the grain. These low-stiffness areas may come in contact with various materials; therefore, understanding the behavior of the damage zones with various materials is important. This paper describes the results and analysis of experimental tests conducted on 130 specimens compressed parallel to the grain, to examine the compression behavior when the low-stiffness areas of glulam (Japanese cedar and Japanese larch) come in contact with mortar, epoxy adhesives, and steel. Compared with specimens joined with steels, the specimens joined with mortar had lower strength and stiffness, whereas those with epoxy structural adhesives had higher or almost equivalent strength and stiffness. Additionally, the specimens joined with mortar had the most significant strain in the damage zone, followed by those with steel loading plates and those with epoxy structural adhesives. These results suggest that using mortar as a contact material has a detrimental effect on the strength and stiffness of glulam. In contrast, the use of epoxy structural adhesives can improve the stiffness of glulam by mitigating the effects of the damage zone.


  • Open Access

    Derivation of the shear modulus on the adhesive layer measured by digital image correlation: study on the tensile shear tests of wood-based materials with veneer

    by Koki Kawano, Kohta Miyamoto, Kenji Aoki, Seiichiro Ukyo

    In this study, peeling veneers of Japanese cedar and Japanese larch were parallel or cross laminated, respectively, and tensile shear tests were conducted. As a result, for Japanese cedar veneers, significant difference in shear strength was found between parallel and cross lamination. On the other hand, for Japanese larch veneers, there was no significant difference in shear strength between different laminate directions. During the shear tests, the strain distribution was measured using Digital Image Correlation. The visualization of principal strain showed that in cross laminated specimens of Japanese cedar, the principal strain was observed around the lathe checks of veneer in the cross layers. Thus, lower shear strength for cross laminated specimens was considered to be due to this strain concentration, which opened the lathe checks and caused the rolling shear failure. Conversely, in cross laminated specimens of Japanese larch, principal strain was not observed as much as in Japanese cedar. Therefore, for Japanese larch, the failure modes were similar for cross and parallel lamination, suggesting that there was no significant difference in the shear strength. In addition, the shear strain on the adhesive layer of the specimen was measured and the shear modulus of the adhesive layer (G adh) was derived by determining the shear stress–strain curve. The shear stress–strain curve was determined using convergence calculations presented in existing literature. The results showed that parallel laminated specimens had higher G adh than cross laminated specimens for both wood species. Furthermore, the G adh of cross laminated specimens were between the commonly known shear modulus of the radial section and the transverse section.


  • Open Access

    Compressive Behavior of Wood Contact with Mortar and Epoxy Resin Adhesives

    by Shun Kosugi, Marina Totsuka, Hiroki Nakashima, Masakazu Ikeda, Kenji Aoki

    In recent years, researchers and engineers have developed a wide range of connection systems between wood and other materials, such as concrete and steel. However, the mechanical behavior of the surfaces where wood meets these materials is yet to be understood. In wood, low-stiffness areas called damage zones form near end grains, when compressed parallel to the grain. These low-stiffness areas may come in contact with various materials; therefore, understanding the behavior of the damage zones with various materials. This paper describes the results and analysis of experimental tests conducted on 130 specimens compressed parallel to the grain, to examine the compression behavior when the low-stiffness areas of glulam (Japanese cedar and Japanese larch) come in contact with mortar, epoxy adhesives, and steel. Compared with specimens joined with steels, the specimens joined with mortar had lower strength and stiffness, whereas those with epoxy structural adhesives had higher or almost equivalent strength and stiffness. Additionally, the specimens joined with mortar had the most significant strain in the damage zone, followed by those with steel loading plates and those with epoxy structural adhesives. These results suggest that using mortar as a contact material has a detrimental effect on the strength and stiffness of glulam. In contrast, the use of epoxy structural adhesives can improve the stiffness of glulam by mitigating the effects of the damage zone.

  • Open Access

    Investigation of mechanical properties and elucidation of factors affecting wood-based structural panels under embedment stress with a circular dowel II: detailed observation for plywood and OSB using DIC and CT scanning

    by Ryutaro Sudo, Kenji Aoki

    Although embedment properties are vital to timber engineering, the behavior and strain distributions in wood-based panels have not been clarified in detail. Our early studies suggested four possible causes of failure behavior and strain distribution: (i) two types of failure behavior (in-plane and out-of-plane failure); (ii) enlargement of the stress-spreading range with increasing load step; (iii) reduction of the stress-spreading range (normalized by dowel diameter) with increasing dowel diameter; and (iv) preferential stress spreading in the vertical and horizontal directions along the strong and weak-axis specifications, respectively. However, these hypotheses were not supported by actual observations. The present study aims to observe and clarify the surface strain distribution via digital image correlation and the internal failure behavior via computed tomography scanning. Most results of the wood-based panel specimens (plywood and oriented strand board) did not contradict the above hypotheses. The failure behaviors of plywood and oriented strand board are likely determined by the direction of the veneer fibers and the layer’s position, respectively. Within the strong axial layer of plywood, fibers on both sides of the dowel were densified by fibers dissociated immediately above the dowel, whereas the weak axial layer in plywood was deformed like a timber under partial compression perpendicular to the grain. In contrast, oriented strand board under an embedding stress exhibited a circularly distributed strain and a dispersed void area in its outer layer. Densification was observed only in the inner layer.


  • Open Access

    Investigation of mechanical properties and elucidation of factors affecting wood-based structural panels under embedment stress with a circular dowel i: analysis of the influence of various conditions on the embedment properties

    by Ryutaro Sudo, Kenji Aoki, Masahiro Inayama

    Embedment properties are vital to timber structural designs, and many types of wood-based structural panels have been developed for diverse uses. Comprehensive and systematic studies regarding the embedment properties of wood-based structural panels are limited. In this study, a jig that allows the observation of fracture processes is developed, and a monotonic tensile embedment test is conducted on plywood, oriented strandboard (both strong and weak axes), particleboard, medium density fiberboard, and hardboard. The parameters used in the test are the dowel diameter, pilot hole size, and end and edge distances. The effects of these parameters on the embedment properties (i.e., the failure mode, ductility, maximum stress, and yield stress) are discussed comprehensively. The failure mode is determined by the edge distance. At a sufficient edge distance, ductile failure occurs, and the load is maintained until the remaining end distance reaches a certain value. The maximum stress and yield stress are analyzed quantitatively via standardized multiple regression analysis. The results suggest the following: (i) The ratio of the in-plane strength to the internal bond strength is related to the failure behavior; (ii) the dowel diameter, fiber direction, and load levels affect the stress spread pattern of the embedment pressure.


  • Groundwater Controlling System

    by Kenji Aoki

    This chapter describes the practical application of water curtains and water curtain grouting in the two sites with different hydrogeological properties, Kurashiki and Namikata. The surveys and tests on water curtain boreholes took place for the initial basic pattern, and prediction by a 3D analysis of the groundwater behaviour was incorporated to evaluate the watertightness of the facilities. Additional water curtain boreholes were placed, if found necessary by surveys. This procedure is explained in this chapter. Also included are the result and effect of grouting in accordance with the characteristics of the cracks at each site and the properties of the grouting materials injected.

  • Cavern Storage and Surrounding Groundwater During Operation

    by Kenji Aoki

    During six years of operation, the behaviour of the groundwater and the pore water pressure were scrupulously analysed. The result did not find a clear anomaly and the cavern is regarded as stable. Watertightness was confirmed comparing the behaviour of the groundwater with the values predicted by the 3D heterogeneous model. The long-term behaviour of the groundwater was predicted. This chapter also outlines the operational equipment and safety management system. The system includes measurements of acoustic emissions (AE) and seismic acceleration. These measurements showed very limited variation and stable operation was assured.

  • Mechanical Stability of Storage Cavern

    by Kenji Aoki

    To discuss the mechanical stability of a cavern requires some consideration of the effect of the groundwater pressure and grouting, as liquefied petroleum gas (LPG) rock storage caverns are excavated maintaining the groundwater pressure. This chapter explains details of the necessary additional supports and post-grouting according to the analysis of the data of the behaviour of the rocks.

  • 3-Dimensional Hydrogeological Model

    by Kenji Aoki

    Accurate understanding and predicting the behaviour of groundwater are crucial to an evaluation of the functionality of groundwater around the storage cavern of a hydrodynamic system. This chapter introduces the case history of the construction and use of a high-precision 3-dimensional (3D) hydrogeological model incorporating the results of detailed surveys, tests and monitoring during excavation. Comparing the geostatistical prediction of the behaviour of groundwater using the 3D hydrogeological model with the actual result of monitoring, it explains the interpreted complex behaviour of groundwater and assesses the applicability of the groundwater control measures.

  • Air-tightness Test

    by Kenji Aoki

    On completion of the excavation of the storage caverns, air-tightness tests were carried out to confirm the functionality of the storage. The test judges air-tightness by observing the preservation of the pressure of compressed air injected into the cavern. The pressure is greatly affected by a variation in the temperature in the gas phase, a variation in the capacity of gas due to seepage and the dissolution of gas into the water. These effects must be measured with high precision. For this purpose, the air-tightness was tested in a small-scale cavern to examine the applicability of the high-precision instruments and the testing method. Finally, the actual air-tightness tests at the Kurashiki and Namikata facilities are described.