Marina Totsuka
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Marina Totsuka has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Kenji Aoki
Graduate School of Agricultural and Life Sciences, The University of Tokyo, Tokyo, Japan
5 shared publications Masahiro Inayama
Department of Biomaterials Sciences, Graduate School of Agricultural and Life Sciences, The University of Tokyo, Tokyo, Japan
4 shared publications- Takeo Hirashima
Graduate School of Engineering, Chiba University, Chiba, Japan
3 shared publications - Hiroki Nakashima
Sumitomo Forestry CO., LTD, Tokyo, Japan
2 shared publications - Masakazu Ikeda
Sumitomo Forestry CO., LTD, Tokyo, Japan
2 shared publications - Minami Suzuki2 shared publications
Latest Publications
- Open Access
- 17 June 2026
- Published by Springer Nature in Journal of Wood Science
- Vol. 72 (1)
Cyclic behavior of large tensile bolted joints for mass timber structures
Owing to their high load-bearing capacity and ease of assembly, tensile-bolted joints are widely used in applications ranging from conventional wooden houses to mass timber buildings. However, the current design method contains several critical gaps that may compromise structural integrity, especially for mass timber structures under cyclic loadings: (i) disregarding cyclic effects, (ii) equating compressive yielding with splitting, and (iii) applying the embedment stiffness formula for dowel-type fasteners. Therefore, the aim of this study is to address these gaps through cyclic bending tests. All tests were conducted on column-base connections using glulam members of the same grade. Experimental results showed three failure modes of timber: compressive yielding, bending failure, and splitting failure. In specimens with longer bolt anchorage lengths, the most ductile compressive yielding was observed. The load-bearing capacity determined by compressive yielding could be predicted by the bearing strength of the material. However, regarding the bending failure, the experimental values were smaller than those calculated by the design method. This result could be attributed to both stress concentration around the specimen and the effects of cyclic loading; the latter reduced the modulus of rupture. In the case of splitting failure, although the failure moments for compressive yielding and splitting were similar, the splitting failure was more brittle. Moreover, the specimen that failed in splitting had dimensions identical to that of the specimen that failed in compressive yielding. The rotational stiffness was approximately twice the calculated values for all specimens. This discrepancy can be attributed to the underestimation of embedment stiffness beneath the washers and in the column end grain, as the current calculation is based on dowel-type fasteners. These findings emphasize the need to revise the design method to more accurately account for embedment stiffness in such joints.
- 17 June 2026
- Published by Springer Nature in Journal of Wood Science
- Vol. 72 (1)
Open AccessCyclic behavior of large tensile bolted joints for mass timber structures
Owing to their high load-bearing capacity and ease of assembly, tensile-bolted joints are widely used in applications ranging from conventional wooden houses to mass timber buildings. However, the current design method contains several critical gaps that may compromise structural integrity, especially for mass timber structures under cyclic loadings: (i) disregarding cyclic effects, (ii) equating compressive yielding with splitting, and (iii) applying the embedment stiffness formula for dowel-type fasteners. Therefore, the aim of this study is to address these gaps through cyclic bending tests. All tests were conducted on column-base connections using glulam members of the same grade. Experimental results showed three failure modes of timber: compressive yielding, bending failure, and splitting failure. In specimens with longer bolt anchorage lengths, the most ductile compressive yielding was observed. The load-bearing capacity determined by compressive yielding could be predicted by the bearing strength of the material. However, regarding the bending failure, the experimental values were smaller than those calculated by the design method. This result could be attributed to both stress concentration around the specimen and the effects of cyclic loading; the latter reduced the modulus of rupture. In the case of splitting failure, although the failure moments for compressive yielding and splitting were similar, the splitting failure was more brittle. Moreover, the specimen that failed in splitting had dimensions identical to that of the specimen that failed in compressive yielding. The rotational stiffness was approximately twice the calculated values for all specimens. This discrepancy can be attributed to the underestimation of embedment stiffness beneath the washers and in the column end grain, as the current calculation is based on dowel-type fasteners. These findings emphasize the need to revise the design method to more accurately account for embedment stiffness in such joints.
- Open Access
- 18 October 2025
- Published by Elsevier in Structures
- Vol. 82
Experimental investigation of the splitting behavior of tensile-bolted joints in timber structures
- 18 October 2025
- Published by Elsevier in Structures
- Vol. 82
Open AccessExperimental investigation of the splitting behavior of tensile-bolted joints in timber structures
- Open Access
- 13 May 2025
- Published by Springer Nature in European Journal of Wood and Wood Products
- Vol. 83 (3) , 1-17
Compressive behavior of wood contact with mortar and epoxy resin adhesives
In recent years, researchers and engineers have developed a wide range of connection systems between wood and other materials, such as concrete and steel. However, the mechanical behavior of the surfaces where wood meets these materials is yet to be understood. In wood, low-stiffness areas called damage zones form near end grains, when compressed parallel to the grain. These low-stiffness areas may come in contact with various materials; therefore, understanding the behavior of the damage zones with various materials is important. This paper describes the results and analysis of experimental tests conducted on 130 specimens compressed parallel to the grain, to examine the compression behavior when the low-stiffness areas of glulam (Japanese cedar and Japanese larch) come in contact with mortar, epoxy adhesives, and steel. Compared with specimens joined with steels, the specimens joined with mortar had lower strength and stiffness, whereas those with epoxy structural adhesives had higher or almost equivalent strength and stiffness. Additionally, the specimens joined with mortar had the most significant strain in the damage zone, followed by those with steel loading plates and those with epoxy structural adhesives. These results suggest that using mortar as a contact material has a detrimental effect on the strength and stiffness of glulam. In contrast, the use of epoxy structural adhesives can improve the stiffness of glulam by mitigating the effects of the damage zone.
- 13 May 2025
- Published by Springer Nature in European Journal of Wood and Wood Products
- Vol. 83 (3) , 1-17
Open AccessCompressive behavior of wood contact with mortar and epoxy resin adhesives
In recent years, researchers and engineers have developed a wide range of connection systems between wood and other materials, such as concrete and steel. However, the mechanical behavior of the surfaces where wood meets these materials is yet to be understood. In wood, low-stiffness areas called damage zones form near end grains, when compressed parallel to the grain. These low-stiffness areas may come in contact with various materials; therefore, understanding the behavior of the damage zones with various materials is important. This paper describes the results and analysis of experimental tests conducted on 130 specimens compressed parallel to the grain, to examine the compression behavior when the low-stiffness areas of glulam (Japanese cedar and Japanese larch) come in contact with mortar, epoxy adhesives, and steel. Compared with specimens joined with steels, the specimens joined with mortar had lower strength and stiffness, whereas those with epoxy structural adhesives had higher or almost equivalent strength and stiffness. Additionally, the specimens joined with mortar had the most significant strain in the damage zone, followed by those with steel loading plates and those with epoxy structural adhesives. These results suggest that using mortar as a contact material has a detrimental effect on the strength and stiffness of glulam. In contrast, the use of epoxy structural adhesives can improve the stiffness of glulam by mitigating the effects of the damage zone.
- Open Access
- 27 December 2024
- Published by Springer Nature in European Journal of Wood and Wood Products
- Vol. 83 (1) , 1-17
Evaluation method of compression parallel to grain stiffness in wood and relationship between stiffness and shape of contact surface
The compressive behavior parallel to the grain is an essential parameter for the designing of multistoried and large timber buildings. However, the application of a compressive force parallel to the grain results in significant deformations near the end grain, which is referred to as the damage zone. Therefore, this study elucidates the mechanism of the damage zone and proposed a methodology to evaluate the properties of the damage zone. The cause of the damage zone was attributed to an uneven contact surface. As the contact surface shape remained non-flat even after reaching 28% of the predicted maximum load, the initial stiffness of compression parallel to the grain necessitated an assessment based on the influence of the damage zone. The Young’s modulus of the damage zone was approximately 2% of that of the middle zone and an evaluation method for the damage zone length was proposed using the strongest link model. The Young’s modulus and damage zone length evaluation methods were used to evaluate the stiffness of the specimens when compressed parallel to the grain. The proposed method could adequately evaluate the experimental values.
- 27 December 2024
- Published by Springer Nature in European Journal of Wood and Wood Products
- Vol. 83 (1) , 1-17
Open AccessEvaluation method of compression parallel to grain stiffness in wood and relationship between stiffness and shape of contact surface
The compressive behavior parallel to the grain is an essential parameter for the designing of multistoried and large timber buildings. However, the application of a compressive force parallel to the grain results in significant deformations near the end grain, which is referred to as the damage zone. Therefore, this study elucidates the mechanism of the damage zone and proposed a methodology to evaluate the properties of the damage zone. The cause of the damage zone was attributed to an uneven contact surface. As the contact surface shape remained non-flat even after reaching 28% of the predicted maximum load, the initial stiffness of compression parallel to the grain necessitated an assessment based on the influence of the damage zone. The Young’s modulus of the damage zone was approximately 2% of that of the middle zone and an evaluation method for the damage zone length was proposed using the strongest link model. The Young’s modulus and damage zone length evaluation methods were used to evaluate the stiffness of the specimens when compressed parallel to the grain. The proposed method could adequately evaluate the experimental values.
- Open Access
- 26 September 2024
- Published by Springer Nature in Research Square
Compressive Behavior of Wood Contact with Mortar and Epoxy Resin Adhesives
In recent years, researchers and engineers have developed a wide range of connection systems between wood and other materials, such as concrete and steel. However, the mechanical behavior of the surfaces where wood meets these materials is yet to be understood. In wood, low-stiffness areas called damage zones form near end grains, when compressed parallel to the grain. These low-stiffness areas may come in contact with various materials; therefore, understanding the behavior of the damage zones with various materials. This paper describes the results and analysis of experimental tests conducted on 130 specimens compressed parallel to the grain, to examine the compression behavior when the low-stiffness areas of glulam (Japanese cedar and Japanese larch) come in contact with mortar, epoxy adhesives, and steel. Compared with specimens joined with steels, the specimens joined with mortar had lower strength and stiffness, whereas those with epoxy structural adhesives had higher or almost equivalent strength and stiffness. Additionally, the specimens joined with mortar had the most significant strain in the damage zone, followed by those with steel loading plates and those with epoxy structural adhesives. These results suggest that using mortar as a contact material has a detrimental effect on the strength and stiffness of glulam. In contrast, the use of epoxy structural adhesives can improve the stiffness of glulam by mitigating the effects of the damage zone.
- 26 September 2024
- Published by Springer Nature in Research Square
Open AccessCompressive Behavior of Wood Contact with Mortar and Epoxy Resin Adhesives
In recent years, researchers and engineers have developed a wide range of connection systems between wood and other materials, such as concrete and steel. However, the mechanical behavior of the surfaces where wood meets these materials is yet to be understood. In wood, low-stiffness areas called damage zones form near end grains, when compressed parallel to the grain. These low-stiffness areas may come in contact with various materials; therefore, understanding the behavior of the damage zones with various materials. This paper describes the results and analysis of experimental tests conducted on 130 specimens compressed parallel to the grain, to examine the compression behavior when the low-stiffness areas of glulam (Japanese cedar and Japanese larch) come in contact with mortar, epoxy adhesives, and steel. Compared with specimens joined with steels, the specimens joined with mortar had lower strength and stiffness, whereas those with epoxy structural adhesives had higher or almost equivalent strength and stiffness. Additionally, the specimens joined with mortar had the most significant strain in the damage zone, followed by those with steel loading plates and those with epoxy structural adhesives. These results suggest that using mortar as a contact material has a detrimental effect on the strength and stiffness of glulam. In contrast, the use of epoxy structural adhesives can improve the stiffness of glulam by mitigating the effects of the damage zone.
- Open Access
- 8 April 2024
- Published by Springer Nature in Fire Technology
- Vol. 60 (4) , 2675-2718
Analytical Model for Non-linear $\user2{M - }\,\,{\varvec{\theta}}$ Relationships of Dowel-Type Timber Connections Exposed to FireRecent experimental evidence has shown that wood–steel–wood dowel-type connections exhibit a semi-rigid behaviour even after 90 min of fire exposure. Because a semi-rigid behaviour influences the bending moment distribution among structural members, considering the moment–rotation relationships within frame analyses in which structural members are modelled as beam elements can enable a realistic fire response analysis that is significantly simpler than the three-dimensional finite element method. This study proposes an analytical methodology that accounts for the thermo-mechanical behaviour of timber and dowels, enabling the simulation of the non-linear moment–rotation relationships under fire conditions. The proposed analytical model divides dowels into a series of elements on an elastoplastic foundation and performs a direct stiffness method in a time-incremental procedure using an element stiffness matrix derived from beam-on-elastic-foundation theory. This study also presents the results of load-carrying tests on timber frames with dowel-type connections performed under ambient and fire conditions. The analytical results were consistent with the fire test results. Additionally, the analyses were also performed under three conditions in which the dowels were rigid, linear elastic, and elastoplastic bodies. These three results converged to the same value after 65 min of heating, which suggests that the ultimate states of beams with dowel-type connections exposed to fire can be modelled by assuming that dowels are rigid bodies.
- 8 April 2024
- Published by Springer Nature in Fire Technology
- Vol. 60 (4) , 2675-2718
Open AccessAnalytical Model for Non-linear $\user2{M - }\,\,{\varvec{\theta}}$ Relationships of Dowel-Type Timber Connections Exposed to FireRecent experimental evidence has shown that wood–steel–wood dowel-type connections exhibit a semi-rigid behaviour even after 90 min of fire exposure. Because a semi-rigid behaviour influences the bending moment distribution among structural members, considering the moment–rotation relationships within frame analyses in which structural members are modelled as beam elements can enable a realistic fire response analysis that is significantly simpler than the three-dimensional finite element method. This study proposes an analytical methodology that accounts for the thermo-mechanical behaviour of timber and dowels, enabling the simulation of the non-linear moment–rotation relationships under fire conditions. The proposed analytical model divides dowels into a series of elements on an elastoplastic foundation and performs a direct stiffness method in a time-incremental procedure using an element stiffness matrix derived from beam-on-elastic-foundation theory. This study also presents the results of load-carrying tests on timber frames with dowel-type connections performed under ambient and fire conditions. The analytical results were consistent with the fire test results. Additionally, the analyses were also performed under three conditions in which the dowels were rigid, linear elastic, and elastoplastic bodies. These three results converged to the same value after 65 min of heating, which suggests that the ultimate states of beams with dowel-type connections exposed to fire can be modelled by assuming that dowels are rigid bodies.
- Open Access
Elastoplastic Analysis of Timber Connections with Dowel-Type Fasteners at Ambient and High Temperatures
Three-dimensional elastoplastic finite element (FE) analysis models considering a damage zone and cleavage were developed, including plastic behavior of embedment tests parallel and perpendicular to the grain at ambient and high temperatures, in order to study the embedment behavior of timber. In a numerical analysis of compression tests to define material properties of timber, the post-yield behavior of the X-axis in the axial direction was larger than the test values when the post-yield slope of the test result were set to the plastic modulus. The reason was that the stress on the Y-axis and Z-axis increased after the yield point; thus, the equivalent yield stress decreased. In the numerical analysis of the embedment tests, the effect of the damage zone must be considered in the analytical models because the initial stiffness of the numerical results in compression parallel to the grain was considerably higher than that of the test results when the damage zone was not considered. In the numerical analysis of the embedment tests in compression perpendicular to the grain, the two models reproduced the stiffness and behavior after the yield point of the test results. The model that considered cleaving showed the stress distribution after cleavage.
Open AccessElastoplastic Analysis of Timber Connections with Dowel-Type Fasteners at Ambient and High Temperatures
Three-dimensional elastoplastic finite element (FE) analysis models considering a damage zone and cleavage were developed, including plastic behavior of embedment tests parallel and perpendicular to the grain at ambient and high temperatures, in order to study the embedment behavior of timber. In a numerical analysis of compression tests to define material properties of timber, the post-yield behavior of the X-axis in the axial direction was larger than the test values when the post-yield slope of the test result were set to the plastic modulus. The reason was that the stress on the Y-axis and Z-axis increased after the yield point; thus, the equivalent yield stress decreased. In the numerical analysis of the embedment tests, the effect of the damage zone must be considered in the analytical models because the initial stiffness of the numerical results in compression parallel to the grain was considerably higher than that of the test results when the damage zone was not considered. In the numerical analysis of the embedment tests in compression perpendicular to the grain, the two models reproduced the stiffness and behavior after the yield point of the test results. The model that considered cleaving showed the stress distribution after cleavage.
- Open Access
- 11 June 2022
- Published by Springer Nature in Journal of Wood Science
- Vol. 68 (1) , 1-14
Experimental study of compressive properties parallel to grain of glulam
This paper describes results and analysis of experiment of compression behavior parallel to grain of glulam (Norway Spruce, Japanese cedar, and Japanese cypress), especially in damage zones near loading plates and joints. To investigate the influence factors of physical properties and the mechanism of the damage zone near the loading plates or the joints, compression tests on 90 specimens and surface-measurement tests on 48 specimens were performed. As a result, it was observed that damage zones existed near the loading plates and the joints. The lengths of the damage zone of wood–wood joints are larger than that of wood–steel joints. The length of the damage zone was independent of the load and the height of the specimens. However, the length of the damage zone and its scatter increase as the width of the cross-section increases, as does the roughness on the contact surface. It was considered that the cause of the damage zone is the roughness on the contact surface and the length of the damage zone depends on the roughness on the contact surface. Therefore, the length of the damage zone depends on the processing accuracy on the contact surface and has an increasing trend as the contact-surface area increases. There was the size effect of the height of the specimens on the compressive strength because of knots.
- 11 June 2022
- Published by Springer Nature in Journal of Wood Science
- Vol. 68 (1) , 1-14
Open AccessExperimental study of compressive properties parallel to grain of glulam
This paper describes results and analysis of experiment of compression behavior parallel to grain of glulam (Norway Spruce, Japanese cedar, and Japanese cypress), especially in damage zones near loading plates and joints. To investigate the influence factors of physical properties and the mechanism of the damage zone near the loading plates or the joints, compression tests on 90 specimens and surface-measurement tests on 48 specimens were performed. As a result, it was observed that damage zones existed near the loading plates and the joints. The lengths of the damage zone of wood–wood joints are larger than that of wood–steel joints. The length of the damage zone was independent of the load and the height of the specimens. However, the length of the damage zone and its scatter increase as the width of the cross-section increases, as does the roughness on the contact surface. It was considered that the cause of the damage zone is the roughness on the contact surface and the length of the damage zone depends on the roughness on the contact surface. Therefore, the length of the damage zone depends on the processing accuracy on the contact surface and has an increasing trend as the contact-surface area increases. There was the size effect of the height of the specimens on the compressive strength because of knots.
- 17 November 2021
- Published by Springer Nature in European Journal of Wood and Wood Products
- Vol. 80 (2) , 451-463
Prediction of strength and stiffness of concentrated compressive load applied to the narrow face of cross-laminated timber
- 17 November 2021
- Published by Springer Nature in European Journal of Wood and Wood Products
- Vol. 80 (2) , 451-463
Prediction of strength and stiffness of concentrated compressive load applied to the narrow face of cross-laminated timber
- Open Access
- 25 May 2021
- Published by Springer Nature in Journal of Wood Science
- Vol. 67 (1) , 1-11
Experimental study on partial compression parallel to grain of solid timber
This paper describes results and analysis of experimental testing of entire and partial compression strength and stiffness parallel to the grain of solid timber (Japanese cedar). To investigate the spreading effects, the size effect of strength and stiffness, and the mechanism of the damage zone located close to the loading plates, tests on 90 specimens were performed. As a result, it was observed that damage zones existed near the loading plates. The observed spreading effects in the compression parallel to the grain were very small which justifies neglecting them regarding strength and stiffness. Although a presence of a size effect of the compression strength parallel to the grain of glulam specimens with knots was reported, the compression strength parallel to the grain of solid wood specimens without knots does not have a size effect. The height and width of the cross-section of the specimens have an influence on the damage zones and, hence, on the effective modulus of elasticity of the full height of the specimens. The compression strength has a correlation with the density of the timber and the width of the annual rings.
- 25 May 2021
- Published by Springer Nature in Journal of Wood Science
- Vol. 67 (1) , 1-11
Open AccessExperimental study on partial compression parallel to grain of solid timber
This paper describes results and analysis of experimental testing of entire and partial compression strength and stiffness parallel to the grain of solid timber (Japanese cedar). To investigate the spreading effects, the size effect of strength and stiffness, and the mechanism of the damage zone located close to the loading plates, tests on 90 specimens were performed. As a result, it was observed that damage zones existed near the loading plates. The observed spreading effects in the compression parallel to the grain were very small which justifies neglecting them regarding strength and stiffness. Although a presence of a size effect of the compression strength parallel to the grain of glulam specimens with knots was reported, the compression strength parallel to the grain of solid wood specimens without knots does not have a size effect. The height and width of the cross-section of the specimens have an influence on the damage zones and, hence, on the effective modulus of elasticity of the full height of the specimens. The compression strength has a correlation with the density of the timber and the width of the annual rings.