Ramasamy Nallamuthu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ramasamy Nallamuthu has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
- Chelliash Suresh Kumar
Department of Aeronautical Engineering, Bharath Institute of Higher Education and Research
2 shared publications - Dr.Mohamed Bak Kamaludeen
BS Abdur Rahman Crescent Institute of science and Technology
2 shared publications Kalaichelvan Kani
Department of Ceramic Technology, ACT Campus, Anna University, Chennai, India
2 shared publications- Veerasundaram Jayaseelan
Department of Mechanical Engineering, Saveetha Engineering College, Chennai, India
2 shared publications - Vellayaraj Arumugam
Department of Aerospace Engineering, Anna University, MIT Campus, Chennai, India
2 shared publications A. Thejesh
Department of Mechanical Engineering, Chennai Institute of Technology, Chennai, India
1 shared publication
Latest Publications
- 12 June 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
Waste to wealth approach: RSM-based tribological optimization of red mud/WC hybrid reinforced AA6061 composites
Waste management has emerged as one of the most significant concerns facing all countries. In order to improve pollution reduction, reuse, and recycling, it is crucial to use the waste for practical solutions. Among the waste materials, 120 million tons of red mud (RM) are generated annually throughout the world. Hence, this study intends to use aluminum waste-driven RM and tungsten carbide (WC) particles as reinforcement to develop the AA6061 metal matrix composites (MMCs) by using stir-casting techniques. The hybrid reinforcement at varying concentrations (2, 4, and 6 wt.%) was incorporated into Al MMCs to systematically investigate their tribological behaviors with the aim of enhancing the wear resistance of aluminum matrix composites and improving their suitability for sliding-wear engineering applications. In addition, the variable wear parameters such as sliding load and speed were used for evaluating the wear characteristics of Al MMCs. The microstructure of the composites was extensively investigated using advanced microstructural characterization techniques, such as scanning electron microscopy with energy-dispersive X-ray analysis, X-ray diffraction, and 3D surface topography, to evaluate the elemental and phase composition, worn surface failure mechanisms, and surface integrity. Moreover, a Brinell hardness study was performed on stir-cast samples to evaluate the mechanical behavior of composites. Additionally, a design of experiment with response surface methodology optimization techniques was utilized to optimize the reinforcement composition and wear parameters. Experimental results revealed that 4 wt. % reinforced composites reduced wear rate and surface roughness by 80.6% and 31.01%, respectively, when compared to base alloy materials, which were validated by optimization analysis. Based on the optimization analysis, the optimal SP and SL were determined to be 300 r/min and 47.56 N, respectively. Subsequently, future directions are indicated that could lead to more efficient and superior wear performance in sustainably reinforced MMCs.
- 12 June 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
Waste to wealth approach: RSM-based tribological optimization of red mud/WC hybrid reinforced AA6061 composites
Waste management has emerged as one of the most significant concerns facing all countries. In order to improve pollution reduction, reuse, and recycling, it is crucial to use the waste for practical solutions. Among the waste materials, 120 million tons of red mud (RM) are generated annually throughout the world. Hence, this study intends to use aluminum waste-driven RM and tungsten carbide (WC) particles as reinforcement to develop the AA6061 metal matrix composites (MMCs) by using stir-casting techniques. The hybrid reinforcement at varying concentrations (2, 4, and 6 wt.%) was incorporated into Al MMCs to systematically investigate their tribological behaviors with the aim of enhancing the wear resistance of aluminum matrix composites and improving their suitability for sliding-wear engineering applications. In addition, the variable wear parameters such as sliding load and speed were used for evaluating the wear characteristics of Al MMCs. The microstructure of the composites was extensively investigated using advanced microstructural characterization techniques, such as scanning electron microscopy with energy-dispersive X-ray analysis, X-ray diffraction, and 3D surface topography, to evaluate the elemental and phase composition, worn surface failure mechanisms, and surface integrity. Moreover, a Brinell hardness study was performed on stir-cast samples to evaluate the mechanical behavior of composites. Additionally, a design of experiment with response surface methodology optimization techniques was utilized to optimize the reinforcement composition and wear parameters. Experimental results revealed that 4 wt. % reinforced composites reduced wear rate and surface roughness by 80.6% and 31.01%, respectively, when compared to base alloy materials, which were validated by optimization analysis. Based on the optimization analysis, the optimal SP and SL were determined to be 300 r/min and 47.56 N, respectively. Subsequently, future directions are indicated that could lead to more efficient and superior wear performance in sustainably reinforced MMCs.
- 21 April 2026
- Published by IOP Publishing in Engineering Research Express
- Vol. 8 (9)
Tribological performance and RSM-based optimization of sustainable aluminium composites using bio-and industrial waste reinforcements
The growing demand for lightweight and durable materials in automotive, marine, and industrial machinery applications has intensified interest in aluminum metal matrix composites (MMCs). However, producing high wear resistance composites while preserving sustainability is a significant challenge. This study develops and evaluates the tribological performance of sustainable aluminum MMCs reinforced with bio-driven coconut shell ash and aluminum waste red mud materials for engineering applications. Stir casting was used to produce sustainable composites with red mud and coconut shell ash particle reinforcements (2-6 wt. %). The wear rate and friction coefficient were evaluated at a constant sliding distance of 1500 m under varying loads (40-60 N) and speeds (300-500 rpm). The composite samples were evaluated using energy dispersive X-ray analysis (EDAX) and scanning electron microscope (SEM), and their surface roughness and textural characteristics were further examined by 3D-surface topography analysis. Moreover, DoE-RSM optimization techniques were utilized to optimize the reinforcement composition and wear parameters. Experimental results showed that the wear rate and surface roughness of 4 wt. % sustainable composites decreased by 73.64% and 24.3%, respectively, as compared to base alloy materials. The tensile strength of 4 wt% hybrid-reinforced composites increased by 17.9% when compared to the base alloy aluminum material. Moreover, the DOE analysis identified the optimal values as a reinforcement concentration of 3.98%, a sliding speed of 300 rpm, and a sliding load of 47 N for providing the lowest wear rate, which has been validated through experiments. Subsequently, future directions are indicated that could lead to more efficient and superior wear performance of sustainably reinforced MMCs.
- 21 April 2026
- Published by IOP Publishing in Engineering Research Express
- Vol. 8 (9)
Tribological performance and RSM-based optimization of sustainable aluminium composites using bio-and industrial waste reinforcements
The growing demand for lightweight and durable materials in automotive, marine, and industrial machinery applications has intensified interest in aluminum metal matrix composites (MMCs). However, producing high wear resistance composites while preserving sustainability is a significant challenge. This study develops and evaluates the tribological performance of sustainable aluminum MMCs reinforced with bio-driven coconut shell ash and aluminum waste red mud materials for engineering applications. Stir casting was used to produce sustainable composites with red mud and coconut shell ash particle reinforcements (2-6 wt. %). The wear rate and friction coefficient were evaluated at a constant sliding distance of 1500 m under varying loads (40-60 N) and speeds (300-500 rpm). The composite samples were evaluated using energy dispersive X-ray analysis (EDAX) and scanning electron microscope (SEM), and their surface roughness and textural characteristics were further examined by 3D-surface topography analysis. Moreover, DoE-RSM optimization techniques were utilized to optimize the reinforcement composition and wear parameters. Experimental results showed that the wear rate and surface roughness of 4 wt. % sustainable composites decreased by 73.64% and 24.3%, respectively, as compared to base alloy materials. The tensile strength of 4 wt% hybrid-reinforced composites increased by 17.9% when compared to the base alloy aluminum material. Moreover, the DOE analysis identified the optimal values as a reinforcement concentration of 3.98%, a sliding speed of 300 rpm, and a sliding load of 47 N for providing the lowest wear rate, which has been validated through experiments. Subsequently, future directions are indicated that could lead to more efficient and superior wear performance of sustainably reinforced MMCs.
- 13 February 2026
- Published by Springer Nature in Cellulose
- Vol. 33 (4) , 2301-2321
Acoustic emission monitoring of 3D printed bio-composite adhesive joints using treated ramie–PLA blends for sustainable engineering applications
- 13 February 2026
- Published by Springer Nature in Cellulose
- Vol. 33 (4) , 2301-2321
Acoustic emission monitoring of 3D printed bio-composite adhesive joints using treated ramie–PLA blends for sustainable engineering applications
- 17 October 2025
- Published by IOP Publishing in Functional Composites and Structures
- Vol. 7 (4) , 045002
Structural optimization of composite wind turbine blades using finite element modeling to enhance the performance efficiency using signal-based technique
The present study investigates the structural behavior of glass and basalt fiber (BF)-reinforced epoxy composites for wind turbine blades using FEA and acoustic emission (AE)-based non-destructive testing. In addition, it focuses on improving failure mode identification and classification to enhance the structural efficiency of composite structures. FEA was used to evaluate variations in internal structural geometry parameters as well as the Von Mises stress distribution across the blades’ pressure and suction sides from root to tip. It focuses on crucial aspects such as stress distribution, damage behavior, and deformations, which are essential considerations for optimizing the design and ensuring the durability of wind turbine blades. Furthermore, the mechanical properties of fiber-reinforced plastic composites have been investigated experimentally. The results showed that glass fiber composite structures produced higher structural properties than BF composites utilized for producing wind blades. A signal-based AE technique is employed to detect and classify failure modes, including matrix cracking, fiber–matrix debonding, and fiber delamination (crack propagation), which are subsequently validated using scanning electron microscopy.
- 17 October 2025
- Published by IOP Publishing in Functional Composites and Structures
- Vol. 7 (4) , 045002
Structural optimization of composite wind turbine blades using finite element modeling to enhance the performance efficiency using signal-based technique
The present study investigates the structural behavior of glass and basalt fiber (BF)-reinforced epoxy composites for wind turbine blades using FEA and acoustic emission (AE)-based non-destructive testing. In addition, it focuses on improving failure mode identification and classification to enhance the structural efficiency of composite structures. FEA was used to evaluate variations in internal structural geometry parameters as well as the Von Mises stress distribution across the blades’ pressure and suction sides from root to tip. It focuses on crucial aspects such as stress distribution, damage behavior, and deformations, which are essential considerations for optimizing the design and ensuring the durability of wind turbine blades. Furthermore, the mechanical properties of fiber-reinforced plastic composites have been investigated experimentally. The results showed that glass fiber composite structures produced higher structural properties than BF composites utilized for producing wind blades. A signal-based AE technique is employed to detect and classify failure modes, including matrix cracking, fiber–matrix debonding, and fiber delamination (crack propagation), which are subsequently validated using scanning electron microscopy.
- 28 August 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (12) , 12012-12025
Empirical Relationships and Optimization for the GMA Welded Bead Profile Properties of AA6061 Alloy Utilizing Alternate Shielding Gas
- 28 August 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (12) , 12012-12025
Empirical Relationships and Optimization for the GMA Welded Bead Profile Properties of AA6061 Alloy Utilizing Alternate Shielding Gas
- 21 March 2024
- Published by Wiley in Polymer Composites
- Vol. 45 (9) , 8076-8090
A comprehensive investigation on tensile behavior of surface‐modified Kevlar hybrid nanocomposites for similar and dissimilar joints
The main objective of this study is to enhance the interfacial adhesion between Kevlar fiber‐reinforced epoxy composite for a single lap joint. This has been achieved by performing various chemical treatments on Kevlar fiber. Moreover, the nanofiller‐added epoxy matrices were also used for investigating its potentiality in a single lap joint. A thorough comparison has been made among various chemical treatments based composite and modified epoxy matrix composite. The tensile strength of similar and dissimilar single lap joints was investigated through experiments and was analyzed by SEM, XRD, and Weibull model. It was perceived that the tensile shear strength and Weibull modulus of the treated similar Kevlar lap joint were 21.45% and 40.18% higher than the similar nanocomposite joint; also, it has been found that an increment of about 79.8% and 76.64% with that of untreated similar Kevlar joint. Furthermore, the failure progression of optimized joints was evaluated by acoustic emission (AE) monitoring.Highlights: Interfacial adhesion study of Kevlar fiber with matrix in single lap joint. Kevlar surface modification and epoxy modified by nanocomposites were used. The lap shear strength of similar and dissimilar single lap joint composites. SEM, XRD, and Weibull analysis and AE monitoring were used for this research. Chemical treatments on Kevlar fiber have enhanced the interfacial adhesion.
- 21 March 2024
- Published by Wiley in Polymer Composites
- Vol. 45 (9) , 8076-8090
A comprehensive investigation on tensile behavior of surface‐modified Kevlar hybrid nanocomposites for similar and dissimilar joints
The main objective of this study is to enhance the interfacial adhesion between Kevlar fiber‐reinforced epoxy composite for a single lap joint. This has been achieved by performing various chemical treatments on Kevlar fiber. Moreover, the nanofiller‐added epoxy matrices were also used for investigating its potentiality in a single lap joint. A thorough comparison has been made among various chemical treatments based composite and modified epoxy matrix composite. The tensile strength of similar and dissimilar single lap joints was investigated through experiments and was analyzed by SEM, XRD, and Weibull model. It was perceived that the tensile shear strength and Weibull modulus of the treated similar Kevlar lap joint were 21.45% and 40.18% higher than the similar nanocomposite joint; also, it has been found that an increment of about 79.8% and 76.64% with that of untreated similar Kevlar joint. Furthermore, the failure progression of optimized joints was evaluated by acoustic emission (AE) monitoring.Highlights: Interfacial adhesion study of Kevlar fiber with matrix in single lap joint. Kevlar surface modification and epoxy modified by nanocomposites were used. The lap shear strength of similar and dissimilar single lap joint composites. SEM, XRD, and Weibull analysis and AE monitoring were used for this research. Chemical treatments on Kevlar fiber have enhanced the interfacial adhesion.
- Open Access
- 30 October 2023
- Published by Universidad Nacional Autonoma de Mexico in Journal of Applied Research and Technology
- Vol. 21 (5) , 850-857
Effect of Hydrothermal Aging Behavior on Surface Treated Kevlar Fiber Laminated Composites
The water sorption characteristics of Kevlar fiber–reinforced epoxy composites were studied by immersion in water at 80 degrees Celsius. The hydrothermal aging process was conducted on treated and untreated Kevlar/epoxy composites; also, the composite was evaluated by the three-point bending test. The phosphoric acid (PA) pretreated with epichlorohydrin (ECH) was used for the surface modification of Kevlar. In the case of chemically modified fiber composites, water uptake was found to be dependent on the chemical treatment done on the fiber surface. The lowest water uptake was observed for composites treated with PA with ECH. The effect of thermal aging on the flexural strength of the treated Kevlar composite was 20.42% higher than the untreated composite. Consequently, the flexural modulus was 13.9% higher than the untreated Kevlar composite. Moreover, the water diffusion coefficient of treated composite 23.19% higher with untreated composite. It was concluded that fiber/matrix degradation time at the interface region was increased in the case of treated composite
- 30 October 2023
- Published by Universidad Nacional Autonoma de Mexico in Journal of Applied Research and Technology
- Vol. 21 (5) , 850-857
Open AccessEffect of Hydrothermal Aging Behavior on Surface Treated Kevlar Fiber Laminated Composites
The water sorption characteristics of Kevlar fiber–reinforced epoxy composites were studied by immersion in water at 80 degrees Celsius. The hydrothermal aging process was conducted on treated and untreated Kevlar/epoxy composites; also, the composite was evaluated by the three-point bending test. The phosphoric acid (PA) pretreated with epichlorohydrin (ECH) was used for the surface modification of Kevlar. In the case of chemically modified fiber composites, water uptake was found to be dependent on the chemical treatment done on the fiber surface. The lowest water uptake was observed for composites treated with PA with ECH. The effect of thermal aging on the flexural strength of the treated Kevlar composite was 20.42% higher than the untreated composite. Consequently, the flexural modulus was 13.9% higher than the untreated Kevlar composite. Moreover, the water diffusion coefficient of treated composite 23.19% higher with untreated composite. It was concluded that fiber/matrix degradation time at the interface region was increased in the case of treated composite
- 21 May 2023
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 238 (4) , 1836-1850
GMA welding investigations on the effect of alternating shielding gases on bead profile characteristics of AA6061 aluminum alloy
The bead profile geometry of aluminum alloy has been taken for investigation and the influence of alternate gases in the gas metal arc welding (GMAW) process. In the GMAW process, welding currents of 105 A, 120 A, 135 A, and 150 A are considered for evaluating the weld parameters. Further, the influence of various alternating duration of argon (Ar) and helium (He) shielding gases on the GMAW process has been investigated. Consequently, the alternating duration between shielding gases is used as 0.25 s (He) and 0.75 s (Ar), 0.5 s (He) and 0.5 s (Ar), and pure argon for joining the AA6061 alloy plates. It is found that the 0.5 s (Ar) and 0.5 s (He) shielding gases promoted fewer porosity effects compared with other alternating shielding gas and pure argon. Also, the microhardness and depth of penetration were significantly improved in 0.5 s (Ar) and 0.5 s (He) compared with 0.75 s (Ar) and 0.25 s (He) and pure argon shielding gas. The welded surface morphological study has been conducted for further evaluation of welding currents and shielding gas effects in the GMAW process.
- 21 May 2023
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 238 (4) , 1836-1850
GMA welding investigations on the effect of alternating shielding gases on bead profile characteristics of AA6061 aluminum alloy
The bead profile geometry of aluminum alloy has been taken for investigation and the influence of alternate gases in the gas metal arc welding (GMAW) process. In the GMAW process, welding currents of 105 A, 120 A, 135 A, and 150 A are considered for evaluating the weld parameters. Further, the influence of various alternating duration of argon (Ar) and helium (He) shielding gases on the GMAW process has been investigated. Consequently, the alternating duration between shielding gases is used as 0.25 s (He) and 0.75 s (Ar), 0.5 s (He) and 0.5 s (Ar), and pure argon for joining the AA6061 alloy plates. It is found that the 0.5 s (Ar) and 0.5 s (He) shielding gases promoted fewer porosity effects compared with other alternating shielding gas and pure argon. Also, the microhardness and depth of penetration were significantly improved in 0.5 s (Ar) and 0.5 s (He) compared with 0.75 s (Ar) and 0.25 s (He) and pure argon shielding gas. The welded surface morphological study has been conducted for further evaluation of welding currents and shielding gas effects in the GMAW process.
- 17 March 2023
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 238 (5) , 2475-2485
Effects of lubricants and billet geometry on the extrusion of AA6063/5% SiCp composites
Lubricants are necessary for metal forming to avoid direct contact, adhesion, transfer, and scratches from materials and tools. It is also essential for increasing tool durability and reducing energy use. The work aims to study the effects of lubricants and billet geometry on the extrusion of AA6063/5% SiCp. The lubricants were used such as graphite, zinc stearate, and molybdenum disulphide. The friction factor has been determined by the lubricant effect and billet geometry. The simulation was done for the lubricated condition which was compared with experimental results. It was found that improved billet quality was obtained by the graphite-lubricated 12:8 configuration die profile. Also, the friction factor for the graphite-lubricated 12:8 configuration dies profile was 10.5% less compared to other configure profiles. Scanning electron microscopy was used to investigate the surface of the lubricated extruded component, and samples were examined utilizing energy-dispersive X-ray analyses.
- 17 March 2023
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 238 (5) , 2475-2485
Effects of lubricants and billet geometry on the extrusion of AA6063/5% SiCp composites
Lubricants are necessary for metal forming to avoid direct contact, adhesion, transfer, and scratches from materials and tools. It is also essential for increasing tool durability and reducing energy use. The work aims to study the effects of lubricants and billet geometry on the extrusion of AA6063/5% SiCp. The lubricants were used such as graphite, zinc stearate, and molybdenum disulphide. The friction factor has been determined by the lubricant effect and billet geometry. The simulation was done for the lubricated condition which was compared with experimental results. It was found that improved billet quality was obtained by the graphite-lubricated 12:8 configuration die profile. Also, the friction factor for the graphite-lubricated 12:8 configuration dies profile was 10.5% less compared to other configure profiles. Scanning electron microscopy was used to investigate the surface of the lubricated extruded component, and samples were examined utilizing energy-dispersive X-ray analyses.
- 1 June 2022
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 64 (6) , 874-883
Effect of extrusion ratio and die angle on the microstructure of an AA6063/SiC composite
Manufacturers often employ the extrusion process to form an object with any cross-section. An experiment was carried out to examine the effect of die angle on the quality of the extruded product. The four types of extrusion dies were designed for finding the desirable quality of aluminium composite extruded billet. The five percentages of the Silicon carbide have been chosen as reinforcement with aluminium alloys. Further, the various extrusion dies configurations were considered as 12:8, 12:2, 12:4, and 8:4 for producing the extruded billets. In addition, the die angles that correspond to the required minimum extrusion load were determined. According to the findings, 12:8 extrusion configurations with a 30° die angle produced the desired quality billet and fine grain structure of extruded product with reduced extrusion load. The extruded billet surface quality was analyzed by scanning electron microscopy.
- 1 June 2022
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 64 (6) , 874-883
Effect of extrusion ratio and die angle on the microstructure of an AA6063/SiC composite
Manufacturers often employ the extrusion process to form an object with any cross-section. An experiment was carried out to examine the effect of die angle on the quality of the extruded product. The four types of extrusion dies were designed for finding the desirable quality of aluminium composite extruded billet. The five percentages of the Silicon carbide have been chosen as reinforcement with aluminium alloys. Further, the various extrusion dies configurations were considered as 12:8, 12:2, 12:4, and 8:4 for producing the extruded billets. In addition, the die angles that correspond to the required minimum extrusion load were determined. According to the findings, 12:8 extrusion configurations with a 30° die angle produced the desired quality billet and fine grain structure of extruded product with reduced extrusion load. The extruded billet surface quality was analyzed by scanning electron microscopy.