Saliou Diouf
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Saliou Diouf has a total of 60 co-authors. Here are the top co-authors by number of shared publications:
- Mxolisi Brendon Shongwe
Department of Chemical, Metallurgical and Materials Engineering, Tshwane University of Technology, Pretoria, South Africa
6 shared publications - Peter Apata Olubambi
University of Johannesburg
6 shared publications - Emmanuel Rotimi Sadiku
Department of Chemical, Metallurgical and Materials Engineering, Tshwane University of Technology, Pretoria, 0001, South Africa
5 shared publications - Munyadziwa Mercy Ramakokovhu
Department of Chemical, Metallurgical and Materials Engineering, Tshwane University of Technology, Pretoria, South Africa
4 shared publications A. Molinari
3 shared publications- Babatunde Abiodun Obadele
Department of Chemical, Materials and Metallurgical Engineering, Botswana International University of Science and Technology, Palapye, Botswana
3 shared publications
Latest Publications
- Open Access
- 1 January 2021
- Published by Fortune Journals in Journal of Pediatrics, Perinatology and Child Health
- Vol. 05 (03) , 158-163
Anemia in among Children Aged 6-59 Months at the Institute of Social Pediatric (ISP) in Dakar Suburban Area
Introduction: Anemia is a public health problem throughout the world with disastrous consequences on the health and cognitive and socio-economic development of populations. Objective: To study the socio-demographic, health and nutritional aspects of children aged 6-59 months with anemia followed at the pediatric social institute (PSI). Methods: This is a cross-sectional study carried out at PSI from 1 November 2018 to 20 February 2019. Children aged 6-59 months with anemia were included. Results: A total of 280 children had anemia among 467 who had a blood count, determining a prevalence of 59.9%. The mean age was 21.34 months 10.82 with a sex ratio of 1.52. Food diversification was started before 4 months (40.7%), between 4 and 5 months (16.1%) and from 6 months (43.2%). Cereals predominated in the diet (66.4%) followed by dairy products (59.6%). The mean hemoglobin level was 9.72±5.12 g/dl. The anemia was mild (48.9%), moderate (48.9%) and severe (2.2%). Microcytic hypochromia was present in 92.1% of the children. Acute malnutrition was present in 9.3% of children. Conclusion: The prevalence of anemia is high in Senegalese suburban areas. It is most often microcytic hypochromic, most probably reflecting an iron deficiency related to errors in food diversification.
- 1 January 2021
- Published by Fortune Journals in Journal of Pediatrics, Perinatology and Child Health
- Vol. 05 (03) , 158-163
Open AccessAnemia in among Children Aged 6-59 Months at the Institute of Social Pediatric (ISP) in Dakar Suburban Area
Introduction: Anemia is a public health problem throughout the world with disastrous consequences on the health and cognitive and socio-economic development of populations. Objective: To study the socio-demographic, health and nutritional aspects of children aged 6-59 months with anemia followed at the pediatric social institute (PSI). Methods: This is a cross-sectional study carried out at PSI from 1 November 2018 to 20 February 2019. Children aged 6-59 months with anemia were included. Results: A total of 280 children had anemia among 467 who had a blood count, determining a prevalence of 59.9%. The mean age was 21.34 months 10.82 with a sex ratio of 1.52. Food diversification was started before 4 months (40.7%), between 4 and 5 months (16.1%) and from 6 months (43.2%). Cereals predominated in the diet (66.4%) followed by dairy products (59.6%). The mean hemoglobin level was 9.72±5.12 g/dl. The anemia was mild (48.9%), moderate (48.9%) and severe (2.2%). Microcytic hypochromia was present in 92.1% of the children. Acute malnutrition was present in 9.3% of children. Conclusion: The prevalence of anemia is high in Senegalese suburban areas. It is most often microcytic hypochromic, most probably reflecting an iron deficiency related to errors in food diversification.
- 11 December 2019
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 54 (17) , 2365-2376
Improving mechanical and thermal properties of graphite–aluminium composite using Si, SiC and eggshell particles
Graphite–aluminium (Gr–Al) composites are being used for diverse engineering applications because of their light weight, good electrical conductivity and thermal properties. However, their applications are limited by high coefficient of thermal expansion and low microhardness values which can be enhanced by adding cheap and efficient fillers. This paper reports the effect of addition of eggshell (ES) particles on the properties of sintered Gr–Al-based composites. Five different composites (Gr–Al, Gr–Al + 20 wt.%Si, Gr–Al + 20 wt.%SiC, Gr–Al + 20Si wt.% + 20 wt.%ES and Gr–Al + 20SiC wt.% + 20 wt.%ES) were sintered at a temperature of 540 ℃, holding time of 10 min, heating rate of 52 ℃/min and pressure of 50 MPa using spark plasma sintering system. The sintered samples were characterized based on morphology, microhardness, relative density, coefficient of thermal expansion and electrical conductivity. Based on SEM images, graphite particles of flake-like structure were largely undeformed while Al particles were smaller, round and irregular in shape and fairly uniformly distributed in the composites. The microhardness value of sintered Gr–Al + 20 wt.%SiC + 20 wt.%ES composite was 39.55 HV compared to 30.46 HV for Gr–Al, the least of the samples. The Gr–Al + 20 wt.%SiC + 20 wt.%ES composite also has a very low thermal expansion coefficient (0.98 × 10−5/K) but lowest electrical conductivity at temperature beyond 150 ℃. Highest densification and minimum relative density (94%) were obtained in Gr–Al + 20 wt.%Si + 20 wt.%ES composite. These enhanced performances are largely due to the incorporation of ES particles. This study therefore demonstrated that ESs particles enhanced microhardness and lowered thermal expansion of Gr–Al-based composites which have promising applications in industries especially for thermal management.
- 11 December 2019
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 54 (17) , 2365-2376
Improving mechanical and thermal properties of graphite–aluminium composite using Si, SiC and eggshell particles
Graphite–aluminium (Gr–Al) composites are being used for diverse engineering applications because of their light weight, good electrical conductivity and thermal properties. However, their applications are limited by high coefficient of thermal expansion and low microhardness values which can be enhanced by adding cheap and efficient fillers. This paper reports the effect of addition of eggshell (ES) particles on the properties of sintered Gr–Al-based composites. Five different composites (Gr–Al, Gr–Al + 20 wt.%Si, Gr–Al + 20 wt.%SiC, Gr–Al + 20Si wt.% + 20 wt.%ES and Gr–Al + 20SiC wt.% + 20 wt.%ES) were sintered at a temperature of 540 ℃, holding time of 10 min, heating rate of 52 ℃/min and pressure of 50 MPa using spark plasma sintering system. The sintered samples were characterized based on morphology, microhardness, relative density, coefficient of thermal expansion and electrical conductivity. Based on SEM images, graphite particles of flake-like structure were largely undeformed while Al particles were smaller, round and irregular in shape and fairly uniformly distributed in the composites. The microhardness value of sintered Gr–Al + 20 wt.%SiC + 20 wt.%ES composite was 39.55 HV compared to 30.46 HV for Gr–Al, the least of the samples. The Gr–Al + 20 wt.%SiC + 20 wt.%ES composite also has a very low thermal expansion coefficient (0.98 × 10−5/K) but lowest electrical conductivity at temperature beyond 150 ℃. Highest densification and minimum relative density (94%) were obtained in Gr–Al + 20 wt.%Si + 20 wt.%ES composite. These enhanced performances are largely due to the incorporation of ES particles. This study therefore demonstrated that ESs particles enhanced microhardness and lowered thermal expansion of Gr–Al-based composites which have promising applications in industries especially for thermal management.
- 15 February 2019
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 50 (2) , 126-139
Wear and corrosion studies of graphite‐aluminum composite reinforced with micro/nano‐TiB2 via spark plasma sintering
The demand for lightweight materials in the automobile and aerospace industries has led to various researches on graphite and graphite‐aluminum composites. The aim of this study was to investigate the effect of the addition of micron/nano TiB2 particles on the properties of graphite‐aluminum composite particularly the wear resistance. The powders were sintered at 550 °C and 50 MPa with more attention on the effect of the sintering temperature on densification, microhardness, coefficient of thermal expansion, wear and frictional force. The results show that the addition of nano TiB2 reduces the densification while improving the hardness of Gr−Al composite with the lowest value being 96.0 % of relative density and the highest microhardness of 43.58 HV 0.1. The coefficient of thermal expansion and frictional force of the composite materials increases with increasing TiB2 content and heating rate (100 °C/min–150 °C/min). TiB2 particles enhance the wear resistance of graphite‐aluminum composite. The addition of micro/nanoparticles of TiB2 to graphite‐aluminum composite increases its corrosion rate with improved passivation behavior in 3.5 wt.% NaCl solution. Nevertheless, 5 wt.% nano (100 °C/min) TiB2 additions do not affect the overall corrosion rate. This work has shown that we can take advantage of some of the properties of TiB2 to improve the performance of graphite‐aluminum composite.
- 15 February 2019
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 50 (2) , 126-139
Wear and corrosion studies of graphite‐aluminum composite reinforced with micro/nano‐TiB2 via spark plasma sintering
The demand for lightweight materials in the automobile and aerospace industries has led to various researches on graphite and graphite‐aluminum composites. The aim of this study was to investigate the effect of the addition of micron/nano TiB2 particles on the properties of graphite‐aluminum composite particularly the wear resistance. The powders were sintered at 550 °C and 50 MPa with more attention on the effect of the sintering temperature on densification, microhardness, coefficient of thermal expansion, wear and frictional force. The results show that the addition of nano TiB2 reduces the densification while improving the hardness of Gr−Al composite with the lowest value being 96.0 % of relative density and the highest microhardness of 43.58 HV 0.1. The coefficient of thermal expansion and frictional force of the composite materials increases with increasing TiB2 content and heating rate (100 °C/min–150 °C/min). TiB2 particles enhance the wear resistance of graphite‐aluminum composite. The addition of micro/nanoparticles of TiB2 to graphite‐aluminum composite increases its corrosion rate with improved passivation behavior in 3.5 wt.% NaCl solution. Nevertheless, 5 wt.% nano (100 °C/min) TiB2 additions do not affect the overall corrosion rate. This work has shown that we can take advantage of some of the properties of TiB2 to improve the performance of graphite‐aluminum composite.
- 18 August 2017
- Published by Springer Nature in Silicon
- Vol. 9 (6) , 855-865
Electrical Conductivity of Cu and Cu-2vol.% Nb Powders and the Effect of Varying Sintering Temperatures on their Mechanical Properties Using Spark Plasma Sintering
- 18 August 2017
- Published by Springer Nature in Silicon
- Vol. 9 (6) , 855-865
Electrical Conductivity of Cu and Cu-2vol.% Nb Powders and the Effect of Varying Sintering Temperatures on their Mechanical Properties Using Spark Plasma Sintering
- 1 September 2016
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 678, 241-248
Effect of starting powder particle size and heating rate on spark plasma sintering of Fe Ni alloys
- 1 September 2016
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 678, 241-248
Effect of starting powder particle size and heating rate on spark plasma sintering of Fe Ni alloys
- 1 March 2016
- Published by Elsevier in Archives de Pédiatrie
- Vol. 23 (3) , 268-274
Les soins kangourou pour nouveau-nés de faible poids de naissance au centre hospitalier national d’enfants Albert-Royer de Dakar
- 1 March 2016
- Published by Elsevier in Archives de Pédiatrie
- Vol. 23 (3) , 268-274
Les soins kangourou pour nouveau-nés de faible poids de naissance au centre hospitalier national d’enfants Albert-Royer de Dakar
- 1 February 2016
- Published by Elsevier in International Journal of Refractory Metals and Hard Materials
- Vol. 55, 16-23
A comparative study of spark plasma sintering and hybrid spark plasma sintering of 93W–4.9Ni–2.1Fe heavy alloy
- 1 February 2016
- Published by Elsevier in International Journal of Refractory Metals and Hard Materials
- Vol. 55, 16-23
A comparative study of spark plasma sintering and hybrid spark plasma sintering of 93W–4.9Ni–2.1Fe heavy alloy
- 23 January 2016
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 27 (5) , 4672-4688
Effect of micron and nano-sized ZrB2 addition on the microstructure and properties of spark plasma sintered graphite–aluminum hybrid composite
- 23 January 2016
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 27 (5) , 4672-4688
Effect of micron and nano-sized ZrB2 addition on the microstructure and properties of spark plasma sintered graphite–aluminum hybrid composite
- 1 November 2015
- Published by Elsevier in Powder Technology
- Vol. 284, 504-513
Spark plasma sintering of graphite–aluminum powder reinforced with SiC/Si particles
- 1 November 2015
- Published by Elsevier in Powder Technology
- Vol. 284, 504-513
Spark plasma sintering of graphite–aluminum powder reinforced with SiC/Si particles