Iman Adibnazari
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Iman Adibnazari has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Michael Thomas Tolley
Department of Mechanical and Aerospace Engineering, University of California San Diego, La Jolla, CA 92093, USA
5 shared publications - Allyson E. Chen
Department of Mechanical and Aerospace Engineering, University of California San Diego, La Jolla, CA, USA
1 shared publication Dimitri D. Deheyn
Marine Biology Research Division, Scripps Institution of Oceanography, La Jolla, CA, USA
1 shared publication- Donald Ruffatto
Department of Mechanical and Aerospace Engineering, University of California, San Diego, San Diego, CA, United States
1 shared publication - Dylan Drotman
Mechanical Engineering, University of California, San Diego, San Diego, California United States of America 92122
1 shared publication George Nakoud
Department of Mechanical and Aerospace Engineering, University of California, San Diego, CA, USA
1 shared publication
Latest Publications
- 13 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 11 (5) , 5502-5509
Bioinspired Agile Swimming With a Highly Underactuated Soft Ribbon Fin
Soft autonomous underwater vehicles (AUVs) that employ biological swimming mechanisms have demonstrated immense promise in navigating marine environments with increased efficiency and adaptability and decreased environmental disturbances in comparison to their rigid counterparts. However, most AUVs with soft propulsors are poorly suited for precise swimming at low speeds and station holding tasks—two capabilities critical to underwater monitoring and manipulation. In contrast, gymnotid fish undulate an elongated ribbon fin to aptly swim at low-speeds with high agility and have inspired soft AUVs that mimic their swimming mechanics. However, these AUVs typically use numerous actuators to force undulatory kinematics in their ribbon fin rather than leveraging the fluid-structure interaction between the soft ribbon fin and surrounding water. In this work, we developed a sparsely actuated robot, inspired by the black ghost knifefish (apteronotus albifrons) and capable of highly agile swimming with only two actuated fin rays. Leveraging prior work on the hydrodynamics of ribbon-finned swimming, we constructed a heuristic for expected thrust generation as a function of the ribbon fin's actuation. Using this heuristic, we investigated four parameterized motion primitives for agile in-plane swimming: 1) forward swimming, 2) banked turning maneuvers, 3) pure yaw rotation, and 4) lateral (i.e., sideways) swimming. We developed a single parametric gait to express all of these primitives and experimentally characterized each primitive. Ultimately, we found that by leveraging fluid-structure interaction, our highly underactuated platform could execute the in-plane swimming capabilities necessary for agile locomotion.
- 13 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 11 (5) , 5502-5509
Bioinspired Agile Swimming With a Highly Underactuated Soft Ribbon Fin
Soft autonomous underwater vehicles (AUVs) that employ biological swimming mechanisms have demonstrated immense promise in navigating marine environments with increased efficiency and adaptability and decreased environmental disturbances in comparison to their rigid counterparts. However, most AUVs with soft propulsors are poorly suited for precise swimming at low speeds and station holding tasks—two capabilities critical to underwater monitoring and manipulation. In contrast, gymnotid fish undulate an elongated ribbon fin to aptly swim at low-speeds with high agility and have inspired soft AUVs that mimic their swimming mechanics. However, these AUVs typically use numerous actuators to force undulatory kinematics in their ribbon fin rather than leveraging the fluid-structure interaction between the soft ribbon fin and surrounding water. In this work, we developed a sparsely actuated robot, inspired by the black ghost knifefish (apteronotus albifrons) and capable of highly agile swimming with only two actuated fin rays. Leveraging prior work on the hydrodynamics of ribbon-finned swimming, we constructed a heuristic for expected thrust generation as a function of the ribbon fin's actuation. Using this heuristic, we investigated four parameterized motion primitives for agile in-plane swimming: 1) forward swimming, 2) banked turning maneuvers, 3) pure yaw rotation, and 4) lateral (i.e., sideways) swimming. We developed a single parametric gait to express all of these primitives and experimentally characterized each primitive. Ultimately, we found that by leveraging fluid-structure interaction, our highly underactuated platform could execute the in-plane swimming capabilities necessary for agile locomotion.
- 13 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 11 (1) , 466-473
Fluidic Control of Untethered Underwater Soft Robots
Soft robots offer considerable advantages relative to traditional, rigid robots, including: versatility, safety, and rich dynamic behavior. A common approach for actuating soft robots is to use pumps and valves to control pressures and flow rates through fluidic channels embedded in a soft material, to cause desired deformations. Usually, an electronic control board carries the pumps, valves, and other components to control this fluid flow. Currently, many existing hydraulic control systems are designed with application-specific performance requirements, forcing researchers to either invest substantial time and effort into developing custom hardware or constrain their soft robotic systems to the limitations of available control platforms. To address these issues, we present an approach to controlling soft robots underwater that can be achieved with a compact, hydraulic control system. We demonstrate this approach with hardware design housed in a 3D-printable enclosure that is water-resistant up to 1 m for 30 min. The system features three independently controlled pumps, each capable of reversible actuation, with a combined maximum pressure of 0.9 MPa and a maximum flow rate of 3.6 L/min. Additionally, we present an approach to flow sensing using onboard RPM sensors, which avoids adding impedance to the fluid channels and, when combined with our direct pump drive approach, enables precise and simultaneous control of multiple soft actuators. This system offers an accessible platform to accelerate the development of future underwater soft robots.
- 13 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 11 (1) , 466-473
Fluidic Control of Untethered Underwater Soft Robots
Soft robots offer considerable advantages relative to traditional, rigid robots, including: versatility, safety, and rich dynamic behavior. A common approach for actuating soft robots is to use pumps and valves to control pressures and flow rates through fluidic channels embedded in a soft material, to cause desired deformations. Usually, an electronic control board carries the pumps, valves, and other components to control this fluid flow. Currently, many existing hydraulic control systems are designed with application-specific performance requirements, forcing researchers to either invest substantial time and effort into developing custom hardware or constrain their soft robotic systems to the limitations of available control platforms. To address these issues, we present an approach to controlling soft robots underwater that can be achieved with a compact, hydraulic control system. We demonstrate this approach with hardware design housed in a 3D-printable enclosure that is water-resistant up to 1 m for 30 min. The system features three independently controlled pumps, each capable of reversible actuation, with a combined maximum pressure of 0.9 MPa and a maximum flow rate of 3.6 L/min. Additionally, we present an approach to flow sensing using onboard RPM sensors, which avoids adding impedance to the fluid channels and, when combined with our direct pump drive approach, enables precise and simultaneous control of multiple soft actuators. This system offers an accessible platform to accelerate the development of future underwater soft robots.
- Open Access
- 24 March 2022
- Published by Frontiers Media SA in Frontiers in Robotics and AI
- Vol. 9, 838913
Branching Vine Robots for Unmapped Environments
While exploring complex unmapped spaces is a persistent challenge for robots, plants are able to reliably accomplish this task. In this work we develop branching robots that deploy through an eversion process that mimics key features of plant growth (i.e., apical extension, branching). We show that by optimizing the design of these robots, we can successfully traverse complex terrain even in unseen instances of an environment. By simulating robot growth through a set of known training maps and evaluating performance with a reward heuristic specific to the intended application (i.e., exploration, anchoring), we optimized robot designs with a particle swarm algorithm. We show these optimization efforts transfer from training on known maps to performance on unseen maps in the same type of environment, and that the resulting designs are specialized to the environment used in training. Furthermore, we fabricated several optimized branching everting robot designs and demonstrated key aspects of their performance in hardware. Our branching designs replicated three properties found in nature: anchoring, coverage, and reachability. The branching designs were able to reach 25% more of a given space than non-branching robots, improved anchoring forces by 12.55×, and were able to hold greater than 100× their own mass (i.e., a device weighing 5 g held 575 g). We also demonstrated anchoring with a robot that held a load of over 66.7 N at an internal pressure of 50 kPa. These results show the promise of using branching vine robots for traversing complex and unmapped terrain.
- 24 March 2022
- Published by Frontiers Media SA in Frontiers in Robotics and AI
- Vol. 9, 838913
Open AccessBranching Vine Robots for Unmapped Environments
While exploring complex unmapped spaces is a persistent challenge for robots, plants are able to reliably accomplish this task. In this work we develop branching robots that deploy through an eversion process that mimics key features of plant growth (i.e., apical extension, branching). We show that by optimizing the design of these robots, we can successfully traverse complex terrain even in unseen instances of an environment. By simulating robot growth through a set of known training maps and evaluating performance with a reward heuristic specific to the intended application (i.e., exploration, anchoring), we optimized robot designs with a particle swarm algorithm. We show these optimization efforts transfer from training on known maps to performance on unseen maps in the same type of environment, and that the resulting designs are specialized to the environment used in training. Furthermore, we fabricated several optimized branching everting robot designs and demonstrated key aspects of their performance in hardware. Our branching designs replicated three properties found in nature: anchoring, coverage, and reachability. The branching designs were able to reach 25% more of a given space than non-branching robots, improved anchoring forces by 12.55×, and were able to hold greater than 100× their own mass (i.e., a device weighing 5 g held 575 g). We also demonstrated anchoring with a robot that held a load of over 66.7 N at an internal pressure of 50 kPa. These results show the promise of using branching vine robots for traversing complex and unmapped terrain.
- 8 February 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 7 (2) , 4134-4141
Combining Suction and Friction to Stabilize a Soft Gripper to Shear and Normal Forces, for Manipulation of Soft Objects in Wet Environments
Soft robotic gripping in wet environments is generally limited by the presence of a liquid that lubricates the interface between the gripper and an object being manipulated. The use of soft grippers is particularly beneficial for manipulating soft, delicate objects, yet is further limited by low grip strengths. We propose the use of suction, a form of adhesion that functions well in wet environments, to enhance soft robotic grippers. We stabilized the suction against shear disturbances using soft actuated fingers decorated with fluid-channeling patterns to enhance friction, counteracting the interfacial lubrication experienced in wet environments. We therefore combined the uses of attachment via suction and shear stability via friction to create an adhesive soft gripper. We evaluated the contributions to attachment of each component to help stabilize it against dislodgement forces that act in parallel and normal to an object that it aimed to manipulate. By identifying these contributions, we envision that such an adhesive gripper can be used to benefit soft robotic manipulation in a variety of wet environments, from surgical to subsea applications.
- 8 February 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 7 (2) , 4134-4141
Combining Suction and Friction to Stabilize a Soft Gripper to Shear and Normal Forces, for Manipulation of Soft Objects in Wet Environments
Soft robotic gripping in wet environments is generally limited by the presence of a liquid that lubricates the interface between the gripper and an object being manipulated. The use of soft grippers is particularly beneficial for manipulating soft, delicate objects, yet is further limited by low grip strengths. We propose the use of suction, a form of adhesion that functions well in wet environments, to enhance soft robotic grippers. We stabilized the suction against shear disturbances using soft actuated fingers decorated with fluid-channeling patterns to enhance friction, counteracting the interfacial lubrication experienced in wet environments. We therefore combined the uses of attachment via suction and shear stability via friction to create an adhesive soft gripper. We evaluated the contributions to attachment of each component to help stabilize it against dislodgement forces that act in parallel and normal to an object that it aimed to manipulate. By identifying these contributions, we envision that such an adhesive gripper can be used to benefit soft robotic manipulation in a variety of wet environments, from surgical to subsea applications.
- Open Access
- 25 May 2021
- Published by Wiley in Advanced Intelligent Systems
- Vol. 3 (7) , 2100001
Gas‐Lubricated Vibration‐Based Adhesion for Robotics
Controllable adhesion has the capability to enable mobile robots to move freely across vertical and inverted surfaces for applications such as inspection, exploration, and cleaning. Previous methods for generating controllable adhesion have relied on fluidic adhesion through suction forces, electromagnetic adhesion through magnetic or electrical interactions, or dry fibrillar structures. Herein, a new method for achieving controllable adhesion by vibrating a flexible plate near a surface, which generates a strong and controllable attraction force, is presented. This adhesion mechanism has the unique property of providing strong adhesion normal to a surface, but very low resistance to motion parallel to the surface, making it attractive for mobile robots. Adhesive capabilities of vibration‐based adhesion (VBA) to characterize adhesive force dependence on vibration frequency and surface size are studied. Spatial pressure measurements within the adhesive zone, in combination with visualization of surface vibration modes, demonstrate that adhesion is localized to the center of the disk and decreases radially. A mobile robot to highlight the capabilities and robustness of VBA for payload transport, climbing to inversion transitions, and adhesion control is developed. Overall, a novel physical mechanism for robot‐surface adhesion that is robust, controllable, and enables rapid low‐friction locomotion is presented herein.
- 25 May 2021
- Published by Wiley in Advanced Intelligent Systems
- Vol. 3 (7) , 2100001
Open AccessGas‐Lubricated Vibration‐Based Adhesion for Robotics
Controllable adhesion has the capability to enable mobile robots to move freely across vertical and inverted surfaces for applications such as inspection, exploration, and cleaning. Previous methods for generating controllable adhesion have relied on fluidic adhesion through suction forces, electromagnetic adhesion through magnetic or electrical interactions, or dry fibrillar structures. Herein, a new method for achieving controllable adhesion by vibrating a flexible plate near a surface, which generates a strong and controllable attraction force, is presented. This adhesion mechanism has the unique property of providing strong adhesion normal to a surface, but very low resistance to motion parallel to the surface, making it attractive for mobile robots. Adhesive capabilities of vibration‐based adhesion (VBA) to characterize adhesive force dependence on vibration frequency and surface size are studied. Spatial pressure measurements within the adhesive zone, in combination with visualization of surface vibration modes, demonstrate that adhesion is localized to the center of the disk and decreases radially. A mobile robot to highlight the capabilities and robustness of VBA for payload transport, climbing to inversion transitions, and adhesion control is developed. Overall, a novel physical mechanism for robot‐surface adhesion that is robust, controllable, and enables rapid low‐friction locomotion is presented herein.