Marina Kopeikina
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Marina Kopeikina has a total of 75 co-authors. Here are the top co-authors by number of shared publications:
- Anatolii Chumak
Інститут надтвердих матеріалів ім. В. М. Бакуля НАН України
8 shared publications - Andrey Manokhin
Bakul Institute for Superhard Materials, National Academy of Sciences of Ukraine, Kyiv, Ukraine
8 shared publications - S. An. Klimenko
Інститут надтвердих матеріалів ім. В. М. Бакуля НАН України
6 shared publications - Юрій Олексійович Мельнійчук
Інститут надтвердих матеріалів ім. В.М. Бакуля НАН України
5 shared publications Serhii Klymenko
4 shared publicationsSerhiy Klymenko
3 shared publications
Latest Publications
- Open Access
- 7 May 2026
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National technical university "Kharkiv Polytechnic Institute" Series: Techniques in a machine industry
- No. 2(12),p. 3-10
MODELING OF OBLIQUE CUTTING FORCES USING A ROUND PCBN INSERT TOOL DURING INTERRUPTED TURNING OF HARDENED STEEL
This study presents a numerical simulation of the cutting process of hardened steel using tools with varying rake angles, equipped with polycrystalline cubic boron nitride (PсBN) inserts. The DEFORM-3D finite element software was used to analyze the stress–strain state in the primary and secondary deformation zones during turning under impact loading. The results demonstrate that using tools with an inclined cutting edge significantly reduces impact load, cutting force, and signal variation, indicating improved process stability. It was established that increasing the rake angle up to 60° leads to a reduction in the normal components of the cutting force and the intensity of material deformation. The simulation results are confirmed by experimental data, supporting the recommendation of oblique cutting as an effective method for machining hardened steels under dynamic loading conditions.
- 7 May 2026
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National technical university "Kharkiv Polytechnic Institute" Series: Techniques in a machine industry
- No. 2(12),p. 3-10
Open AccessMODELING OF OBLIQUE CUTTING FORCES USING A ROUND PCBN INSERT TOOL DURING INTERRUPTED TURNING OF HARDENED STEEL
This study presents a numerical simulation of the cutting process of hardened steel using tools with varying rake angles, equipped with polycrystalline cubic boron nitride (PсBN) inserts. The DEFORM-3D finite element software was used to analyze the stress–strain state in the primary and secondary deformation zones during turning under impact loading. The results demonstrate that using tools with an inclined cutting edge significantly reduces impact load, cutting force, and signal variation, indicating improved process stability. It was established that increasing the rake angle up to 60° leads to a reduction in the normal components of the cutting force and the intensity of material deformation. The simulation results are confirmed by experimental data, supporting the recommendation of oblique cutting as an effective method for machining hardened steels under dynamic loading conditions.
- Open Access
- 10 February 2026
- Published by Chernihiv Polytechnic National University in TECHNICAL SCIENCES AND TECHNOLOGIES
- No. 1(43)
Modeling of vibration transfer and evaluation of vibration resistance of tools during impact cutting
The paper presents the results of mathematical modeling of vibration displacements of the cutting tool and assessment of vibration resistance of the cutting process under shock impulse loads. The dynamic model of the elastic system “tool-tool holder- workpiece” is considered, taking into account the feedback between the instantaneous cutting depth and the components of the cutting force. Based on the numerical solution of the second-order differential equation, an analysis of the influence of the geometry of the tool, in particular the angle of inclination of the cutting edge, on the amplitude of vibration displacements and the maximum values of the radial component of the cutting force is carried out. It is shown that an increase in the angle of inclination of the cutting edge leads to a decrease in the amplitude of tool oscillations and an increase in the vibration resistance of the cutting process. It is established that tools with an oblique radius cutting edge at angles λ = 50-60° provide maximum machining stability under conditions of impulse shock loads.
- 10 February 2026
- Published by Chernihiv Polytechnic National University in TECHNICAL SCIENCES AND TECHNOLOGIES
- No. 1(43)
Open AccessModeling of vibration transfer and evaluation of vibration resistance of tools during impact cutting
The paper presents the results of mathematical modeling of vibration displacements of the cutting tool and assessment of vibration resistance of the cutting process under shock impulse loads. The dynamic model of the elastic system “tool-tool holder- workpiece” is considered, taking into account the feedback between the instantaneous cutting depth and the components of the cutting force. Based on the numerical solution of the second-order differential equation, an analysis of the influence of the geometry of the tool, in particular the angle of inclination of the cutting edge, on the amplitude of vibration displacements and the maximum values of the radial component of the cutting force is carried out. It is shown that an increase in the angle of inclination of the cutting edge leads to a decrease in the amplitude of tool oscillations and an increase in the vibration resistance of the cutting process. It is established that tools with an oblique radius cutting edge at angles λ = 50-60° provide maximum machining stability under conditions of impulse shock loads.
- Open Access
- 26 June 2025
- Published by Zhytomyr Polytechnic State University in Технічна інженерія
- No. 1(95),p. 67-75
Визначення стабільності процесу різання в умовах динамічного навантаження
Продемонстровано підхід до кількісного визначення стабільності процесу різання в умовах динамічного навантаження. З цією метою пропонується оцінювати часові ряди величин сили різання та визначати показник стабільності як функцію від точності прогнозу, що визначається величиною середньоквадратичної похибки відхилення (RSME) величин прогнозованих та експериментальних значень сигналу сили різання. Прогнозування залежності здійснюється з використанням машинного навчання на основі методу екстремального градієнтного прискорення (XGB). Практична значущість розробленої методики полягає у можливості надати кількісну оцінку стабільності процесу різання незалежно від стану різальної кромки інструменту, що може характеризуватися як рівномірним зношуванням, так і наявністю дефектів (мікровикришувань, сколів) та макроруйнуванням. Експериментальні значення сили сигналів різання отримано при обробці заготовки з загартованої сталі з повздовжними пазами для імітації імпульсного динамічного навантаження на різальний інструмент з полікристалічним надтвердим композитом (PcBN) «Борсиніт». Фіксація значень сили різання здійснювалася з використанням динамометра УДМ-600 та АЦП ADA-1406. Встановлено, що значення RSME в діапазоні застосованих умов обробки (v = 120–210 м/хв; S = 0,10–0,19 мм/об; t = 0,1–0,2 мм) знаходилися в межах 40–60 Н. Оптимальні параметри режимів різання, що забезпечують стабільне різання в умовах динамічних навантажень відповідають умовам: повздовжня подача інструменту S = 0,10–0,12 мм/об; глибина різання t = 0,125–0,175 мм; швидкість різання v = 180–200 м/хв при RSME < 56. Також показано, що використання інструменту з кутом нахилу різальної кромки λ = 40–50° практично виключає руйнування різця та підвищує стабільність процесу різання.
- 26 June 2025
- Published by Zhytomyr Polytechnic State University in Технічна інженерія
- No. 1(95),p. 67-75
Open AccessВизначення стабільності процесу різання в умовах динамічного навантаження
Продемонстровано підхід до кількісного визначення стабільності процесу різання в умовах динамічного навантаження. З цією метою пропонується оцінювати часові ряди величин сили різання та визначати показник стабільності як функцію від точності прогнозу, що визначається величиною середньоквадратичної похибки відхилення (RSME) величин прогнозованих та експериментальних значень сигналу сили різання. Прогнозування залежності здійснюється з використанням машинного навчання на основі методу екстремального градієнтного прискорення (XGB). Практична значущість розробленої методики полягає у можливості надати кількісну оцінку стабільності процесу різання незалежно від стану різальної кромки інструменту, що може характеризуватися як рівномірним зношуванням, так і наявністю дефектів (мікровикришувань, сколів) та макроруйнуванням. Експериментальні значення сили сигналів різання отримано при обробці заготовки з загартованої сталі з повздовжними пазами для імітації імпульсного динамічного навантаження на різальний інструмент з полікристалічним надтвердим композитом (PcBN) «Борсиніт». Фіксація значень сили різання здійснювалася з використанням динамометра УДМ-600 та АЦП ADA-1406. Встановлено, що значення RSME в діапазоні застосованих умов обробки (v = 120–210 м/хв; S = 0,10–0,19 мм/об; t = 0,1–0,2 мм) знаходилися в межах 40–60 Н. Оптимальні параметри режимів різання, що забезпечують стабільне різання в умовах динамічних навантажень відповідають умовам: повздовжня подача інструменту S = 0,10–0,12 мм/об; глибина різання t = 0,125–0,175 мм; швидкість різання v = 180–200 м/хв при RSME < 56. Також показано, що використання інструменту з кутом нахилу різальної кромки λ = 40–50° практично виключає руйнування різця та підвищує стабільність процесу різання.
- Open Access
- 27 December 2024
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National technical university "Kharkiv Polytechnic Institute" Series: Techniques in a machine industry
- No. 1(9),p. 13-18
STRENGTH FEATURES OF HARDENED STEEL TREATMENT BY TOOLS EQUIPPED WITH PcBN OF BH, BL GROUP
A set of studies has been carried out to investigate the power features of machining hardened steel with a tool equipped with PcBN of the VN group, obtained from the initial cBN powders coated with Ti and uncoated compounds, as well as PcBN of the BL group. The determined features of the machining process have shown that the wear of the cutting tool has a significant impact on the value of the cutting force components – when cutting at a speed of 350 m/min, the machining process with a tool of PcBN group BH obtained from coated powders, compared to machining with a tool of PcBN group BH obtained from uncoated powders, is characterized by a 15–20% lower value of the cutting force components. During high-speed machining under dynamic shock loads, a tool equipped with BH PcBN obtained from coated cBN powders, unlike cutters made of BL PcBN, retains its performance at a feed rate of 0, 38 mm/rev - usually, working under such conditions leads to brittle fracture of the tool equipped with PcBN of group BL due to chipping of individual fragments of the cutting edge from the back surface, and on the tool equipped with PcBN (5% Ti), there are separate traces of microchipping. The obtained research results indicate the possibility of using tools equipped with PcBN of group BH, sintered from coated cBN powders, under high-speed cutting conditions, which is typical for tools made of PcBN of group BL, but in the presence of dynamic loading.
- 27 December 2024
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National technical university "Kharkiv Polytechnic Institute" Series: Techniques in a machine industry
- No. 1(9),p. 13-18
Open AccessSTRENGTH FEATURES OF HARDENED STEEL TREATMENT BY TOOLS EQUIPPED WITH PcBN OF BH, BL GROUP
A set of studies has been carried out to investigate the power features of machining hardened steel with a tool equipped with PcBN of the VN group, obtained from the initial cBN powders coated with Ti and uncoated compounds, as well as PcBN of the BL group. The determined features of the machining process have shown that the wear of the cutting tool has a significant impact on the value of the cutting force components – when cutting at a speed of 350 m/min, the machining process with a tool of PcBN group BH obtained from coated powders, compared to machining with a tool of PcBN group BH obtained from uncoated powders, is characterized by a 15–20% lower value of the cutting force components. During high-speed machining under dynamic shock loads, a tool equipped with BH PcBN obtained from coated cBN powders, unlike cutters made of BL PcBN, retains its performance at a feed rate of 0, 38 mm/rev - usually, working under such conditions leads to brittle fracture of the tool equipped with PcBN of group BL due to chipping of individual fragments of the cutting edge from the back surface, and on the tool equipped with PcBN (5% Ti), there are separate traces of microchipping. The obtained research results indicate the possibility of using tools equipped with PcBN of group BH, sintered from coated cBN powders, under high-speed cutting conditions, which is typical for tools made of PcBN of group BL, but in the presence of dynamic loading.
- Open Access
- 8 December 2024
- Published by V. N. Karazin Kharkiv National University in East European Journal of Physics
- No. 4,p. 11-24
A Review of Vacuum-ARC Multilayer Coatings with High-Strength Characteristics and Adhesive Properties
Using the TiSiN/MeN (Me = Cr, Nb, W, Mo, TiZr) coatings system as an example, the analyzed results of multilayer coatings with nanolayers of various functional purposes require a systematic approach to understanding the role of selected materials, growth conditions, microstructure, and required properties. Nanoscale grain boundaries, coherent interlayer boundaries, and changes in columnar morphology at the micro level significantly change the physical and mechanical properties of coatings. For all coatings, an increase in mechanical parameters (hardness, modulus of elasticity) is observed due to the formation of a nanoscale phase (which additionally prevents the movement of dislocations together with nanocomposite TiSiN). In addition, there is a mismatch of crystal lattices between layers. Effectively contributes to strengthening due to variable fields of stresses and strains caused by deformations of elastic coherence. Research has determined optimal conditions for the formation of coatings in a wide range of gas (nitrogen) pressure and shear potential, which also allowed for establishing the factors of structural changes and operational characteristics that will be optimal for their industrial use.
- 8 December 2024
- Published by V. N. Karazin Kharkiv National University in East European Journal of Physics
- No. 4,p. 11-24
Open AccessA Review of Vacuum-ARC Multilayer Coatings with High-Strength Characteristics and Adhesive Properties
Using the TiSiN/MeN (Me = Cr, Nb, W, Mo, TiZr) coatings system as an example, the analyzed results of multilayer coatings with nanolayers of various functional purposes require a systematic approach to understanding the role of selected materials, growth conditions, microstructure, and required properties. Nanoscale grain boundaries, coherent interlayer boundaries, and changes in columnar morphology at the micro level significantly change the physical and mechanical properties of coatings. For all coatings, an increase in mechanical parameters (hardness, modulus of elasticity) is observed due to the formation of a nanoscale phase (which additionally prevents the movement of dislocations together with nanocomposite TiSiN). In addition, there is a mismatch of crystal lattices between layers. Effectively contributes to strengthening due to variable fields of stresses and strains caused by deformations of elastic coherence. Research has determined optimal conditions for the formation of coatings in a wide range of gas (nitrogen) pressure and shear potential, which also allowed for establishing the factors of structural changes and operational characteristics that will be optimal for their industrial use.
- 1 January 2024
- Published by Chernihiv Polytechnic National University in TECHNICAL SCIENCES AND TECHNOLOGIES
- No. 3(37)
Багатошарові леговані нітридні покриття системи TiAlN
Наведено результати досліджень гами багатошарових наноструктурних покриттів на основі системи TiAlN – стру-ктурного стану, морфології, складу, мікрогеометрії інтерфейсу. Покриття загальною товщиною 7–8 мкм з товщиною ша-рів (TiAlN/СrN) 20–30 нм, нанесене вакуумно-дуговим методом на основу з надтвердої кераміки на основі кубічного нітриду бору. Розглянуто вплив на показники стану інтерфейсу покриттів легування їхніх матеріалів Y та Si, комплексом елементів – Y, Zr, Nb. На основі аналізу результатів вивчення інтерфейсу покриттів методом скетч-тестування встановлено агезійний і когезійний механізми руйнування покриттів залежно від рівня легування їхніх матеріалів, запропоновано перспективні напрями використання покриттів для застосування в різальному інструменті з PcBN
- 1 January 2024
- Published by Chernihiv Polytechnic National University in TECHNICAL SCIENCES AND TECHNOLOGIES
- No. 3(37)
Багатошарові леговані нітридні покриття системи TiAlN
Наведено результати досліджень гами багатошарових наноструктурних покриттів на основі системи TiAlN – стру-ктурного стану, морфології, складу, мікрогеометрії інтерфейсу. Покриття загальною товщиною 7–8 мкм з товщиною ша-рів (TiAlN/СrN) 20–30 нм, нанесене вакуумно-дуговим методом на основу з надтвердої кераміки на основі кубічного нітриду бору. Розглянуто вплив на показники стану інтерфейсу покриттів легування їхніх матеріалів Y та Si, комплексом елементів – Y, Zr, Nb. На основі аналізу результатів вивчення інтерфейсу покриттів методом скетч-тестування встановлено агезійний і когезійний механізми руйнування покриттів залежно від рівня легування їхніх матеріалів, запропоновано перспективні напрями використання покриттів для застосування в різальному інструменті з PcBN
- Open Access
- 1 January 2024
- Published by Chernihiv Polytechnic National University in TECHNICAL SCIENCES AND TECHNOLOGIES
- No. 1(35),p. 65-74
STRUCTURAL STATE OF COMPOSITES SINTERED FROM cBN POEDERS WITH A COATING OF COMPOUNDS Ti
The paper presents the results of experimental studies of the structural state of composites obtained at high temperatures and pressures from cBN powders with coatings deposited by CVD from Ti compounds using a gas transport reaction. The features and quantitative parameters of the structure of the composites depending on the presence of Ti in the coating were determined. It has been experimentally established that the matrices of the obtained composites are formed by submicron grains of TiN and TiB2, the quantitative differences of which correspond to the concentration of Ti in the coating - from 3 to 8 %. The structure of the obtained composites is characterized by a uniform distribution of the ceramic matrix between the cBN grains, which is achieved due to the high-quality encapsulation of individual grains of the superhard phase in the coating. The ceramic layers have the largest dimensions (up to 10-12 μm) in the area of triple joints, the width of the zone between two adjacent cBN particles is < 1 μm. When moving from a coated powder to a composite, the shape of the diffraction peaks changes, which is associated with the stresses of the first and/or second kind inherent in the studied samples. Sintering of the powder leads to a decrease in the size of the blocks from 56 nm to 27 nm, an increase in the lattice strain from 0.11 to 0.24 %, in TiN - to an increase in the lattice parameter in the composite by 10% (from 0.4244 nm to 0.4253 nm), a decrease in the size of crystallites within individual grains from 100 nm to 20 nm, and an increase in the lattice strain by 0.47 %. At the same time, TiN nitride is supersaturated with nitrogen, which is a significant increase in its lattice parameter, and the coating formed in this case is exclusively oriented in the (022) direction.
- 1 January 2024
- Published by Chernihiv Polytechnic National University in TECHNICAL SCIENCES AND TECHNOLOGIES
- No. 1(35),p. 65-74
Open AccessSTRUCTURAL STATE OF COMPOSITES SINTERED FROM cBN POEDERS WITH A COATING OF COMPOUNDS Ti
The paper presents the results of experimental studies of the structural state of composites obtained at high temperatures and pressures from cBN powders with coatings deposited by CVD from Ti compounds using a gas transport reaction. The features and quantitative parameters of the structure of the composites depending on the presence of Ti in the coating were determined. It has been experimentally established that the matrices of the obtained composites are formed by submicron grains of TiN and TiB2, the quantitative differences of which correspond to the concentration of Ti in the coating - from 3 to 8 %. The structure of the obtained composites is characterized by a uniform distribution of the ceramic matrix between the cBN grains, which is achieved due to the high-quality encapsulation of individual grains of the superhard phase in the coating. The ceramic layers have the largest dimensions (up to 10-12 μm) in the area of triple joints, the width of the zone between two adjacent cBN particles is < 1 μm. When moving from a coated powder to a composite, the shape of the diffraction peaks changes, which is associated with the stresses of the first and/or second kind inherent in the studied samples. Sintering of the powder leads to a decrease in the size of the blocks from 56 nm to 27 nm, an increase in the lattice strain from 0.11 to 0.24 %, in TiN - to an increase in the lattice parameter in the composite by 10% (from 0.4244 nm to 0.4253 nm), a decrease in the size of crystallites within individual grains from 100 nm to 20 nm, and an increase in the lattice strain by 0.47 %. At the same time, TiN nitride is supersaturated with nitrogen, which is a significant increase in its lattice parameter, and the coating formed in this case is exclusively oriented in the (022) direction.
- Open Access
- 21 November 2023
- Published by National Technical University Kharkiv Polytechnic Institute in Cutting & Tools in Technological System
- No. 99,p. 21-33
ACTUAL CONTACT AREA ON THE WORN CLEARANCE FACE OF THE CUTTER WITH THE ROUND KYBORITE INSERT
For a tool equipped with a circular cutting insert, a dependence is proposed for calculating the nominal area of the contact area on the back surface. It is proved that the actual area of the contact area of the tool differs significantly from the nominal one due to the presence of a system of micro-irregularities, which makes a difference in the assessment of machining process parameters. Using the example of a tool equipped with a circular cutting insert made of polycrystalline cubic boron nitride ciborite, an approach to determining the actual contact area of the back surface with the workpiece during finishing turning of hardened steel is considered. The possibility of taking into account the influence of the system of irregularities in the contact area, determined by the parameters of its topography, on the size of the actual area is shown, and the ratio of the actual and nominal areas of the contact areas of the tool is determined, and it is found that, depending on the degree of development of the microrelief, the ratio of the actual and nominal areas of the contact surface of the cutter differs by at least 20%. It is shown that the actual contact area is also related to the total length of the main and auxiliary cutting edges, determined by the maximum values of the main and auxiliary angles in the cutter plan, and the size of the wear chamfer on the back surface of the cutter.
- 21 November 2023
- Published by National Technical University Kharkiv Polytechnic Institute in Cutting & Tools in Technological System
- No. 99,p. 21-33
Open AccessACTUAL CONTACT AREA ON THE WORN CLEARANCE FACE OF THE CUTTER WITH THE ROUND KYBORITE INSERT
For a tool equipped with a circular cutting insert, a dependence is proposed for calculating the nominal area of the contact area on the back surface. It is proved that the actual area of the contact area of the tool differs significantly from the nominal one due to the presence of a system of micro-irregularities, which makes a difference in the assessment of machining process parameters. Using the example of a tool equipped with a circular cutting insert made of polycrystalline cubic boron nitride ciborite, an approach to determining the actual contact area of the back surface with the workpiece during finishing turning of hardened steel is considered. The possibility of taking into account the influence of the system of irregularities in the contact area, determined by the parameters of its topography, on the size of the actual area is shown, and the ratio of the actual and nominal areas of the contact areas of the tool is determined, and it is found that, depending on the degree of development of the microrelief, the ratio of the actual and nominal areas of the contact surface of the cutter differs by at least 20%. It is shown that the actual contact area is also related to the total length of the main and auxiliary cutting edges, determined by the maximum values of the main and auxiliary angles in the cutter plan, and the size of the wear chamfer on the back surface of the cutter.
- Open Access
- 3 July 2023
- Published by Zhytomyr Polytechnic State University in Технічна інженерія
- No. 1(91),p. 17-25
Працездатність різального інструменту, оснащеного ПКНБ групи BL, при швидкісній обробці загартованої сталі
У роботі досліджувалися розроблені в Інституті надтвердих матеріалів ім. В.М. Бакуля інструменти з надтвердих матеріалів на основі КНБ групи BL, виготовлені з додаванням керамічних компонентів TaN, TiC, TiN. Такі матеріали класифікуються як керамоматричні композити (КМК). Твердість нових модифікацій композитів інструментального призначення становила від 31,2 до 40,2 ГПа. Експериментальні дослідження проводилися в умовах високошвидкісного різання загартованих сталей ШХ15 та ХВГ. Вивчалася працездатність надтвердих композитів за критерієм відсутності крихкого руйнування різальної кромки інструменту та ефективність нових композитів за критерієм мінімальної інтенсивності зношування задньої поверхні різців під час різання з режимами, що відповідають умовам фінішної обробки. Високі експлуатаційні параметри – якість оброки та мінімальна інтенсивність зношування – були продемонстровані інструментами, що оснащені КМК, які містять матрицю, утворену карбідом титану.
- 3 July 2023
- Published by Zhytomyr Polytechnic State University in Технічна інженерія
- No. 1(91),p. 17-25
Open AccessПрацездатність різального інструменту, оснащеного ПКНБ групи BL, при швидкісній обробці загартованої сталі
У роботі досліджувалися розроблені в Інституті надтвердих матеріалів ім. В.М. Бакуля інструменти з надтвердих матеріалів на основі КНБ групи BL, виготовлені з додаванням керамічних компонентів TaN, TiC, TiN. Такі матеріали класифікуються як керамоматричні композити (КМК). Твердість нових модифікацій композитів інструментального призначення становила від 31,2 до 40,2 ГПа. Експериментальні дослідження проводилися в умовах високошвидкісного різання загартованих сталей ШХ15 та ХВГ. Вивчалася працездатність надтвердих композитів за критерієм відсутності крихкого руйнування різальної кромки інструменту та ефективність нових композитів за критерієм мінімальної інтенсивності зношування задньої поверхні різців під час різання з режимами, що відповідають умовам фінішної обробки. Високі експлуатаційні параметри – якість оброки та мінімальна інтенсивність зношування – були продемонстровані інструментами, що оснащені КМК, які містять матрицю, утворену карбідом титану.
- Open Access
- 1 January 2023
- Published by Chernihiv Polytechnic National University in TECHNICAL SCIENCES AND TECHNOLOGIES
- No. 2(32),p. 42-51
INITIAL PREREQUISITES FOR THE DEVELOPMENT OF TECHNOLOGY FOR TURNING WELDED PARTS
Визначено вихідні передумови розробки технології точіння наплавлених деталей, які включають розрахунок припусків та граничних розмірів виробу відповідно до технологічних переходів і товщини наплавленого покриття. Наведений підхід до встановлення глибини різання, яка забезпечує наявність у шарі покриття на обробленій деталі найкращих і найбільш сталих властивостей, що надає виробу кращі експлуатаційні показники, зокрема більшу зносостійкість. У загальному вигляді середня глибина різання може бути визначена за допомогою кривої відносної опорної поверхні профілю покриття, а з урахуванням методу Херста змінну частину глибини різання під час оброблення покриттів може бути визначено через фрактальну розмірність профілю їхньої поверхні. Розглянуто деякі підходи до визначення швидкості різання, які базуються на вимогах забезпечення якості шару наплавленого покриття і стійкості різального інструменту, та геометричних параметрів інструменту з урахуванням властивостей оброблюваного матеріалу.
- 1 January 2023
- Published by Chernihiv Polytechnic National University in TECHNICAL SCIENCES AND TECHNOLOGIES
- No. 2(32),p. 42-51
Open AccessINITIAL PREREQUISITES FOR THE DEVELOPMENT OF TECHNOLOGY FOR TURNING WELDED PARTS
Визначено вихідні передумови розробки технології точіння наплавлених деталей, які включають розрахунок припусків та граничних розмірів виробу відповідно до технологічних переходів і товщини наплавленого покриття. Наведений підхід до встановлення глибини різання, яка забезпечує наявність у шарі покриття на обробленій деталі найкращих і найбільш сталих властивостей, що надає виробу кращі експлуатаційні показники, зокрема більшу зносостійкість. У загальному вигляді середня глибина різання може бути визначена за допомогою кривої відносної опорної поверхні профілю покриття, а з урахуванням методу Херста змінну частину глибини різання під час оброблення покриттів може бути визначено через фрактальну розмірність профілю їхньої поверхні. Розглянуто деякі підходи до визначення швидкості різання, які базуються на вимогах забезпечення якості шару наплавленого покриття і стійкості різального інструменту, та геометричних параметрів інструменту з урахуванням властивостей оброблюваного матеріалу.