S. An. Klimenko
S. An. Klimenko has a total of 42 co-authors. Here are the top co-authors by number of shared publications:
- Anatolii Chumak
Інститут надтвердих матеріалів ім. В. М. Бакуля НАН України
7 shared publications - Andrey Manokhin
Bakul Institute for Superhard Materials, National Academy of Sciences of Ukraine, Kyiv, Ukraine
6 shared publications - Marina Kopeikina
Інститут надтвердих матеріалів ім. В.М. Бакуля Національної академії наук України
6 shared publications - Юрій Олексійович Мельнійчук
Інститут надтвердих матеріалів ім. В.М. Бакуля НАН України
4 shared publications V. M. Beresnev
Karazin Kharkiv National University, Ministry of Education and Science of Ukraine
3 shared publications- Yurii Melniychuk
V. Bakul Institute for Superhard Materials, National Academy of Sciences of Ukraine, 2 Avtozavodska St., 04074 Kyiv, Ukraine
3 shared publications
Latest Publications
- Open Access
- 27 December 2024
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National technical university "Kharkiv Polytechnic Institute" Series: Techniques in a machine industry
- No. 1(9),p. 13-18
STRENGTH FEATURES OF HARDENED STEEL TREATMENT BY TOOLS EQUIPPED WITH PcBN OF BH, BL GROUP
A set of studies has been carried out to investigate the power features of machining hardened steel with a tool equipped with PcBN of the VN group, obtained from the initial cBN powders coated with Ti and uncoated compounds, as well as PcBN of the BL group. The determined features of the machining process have shown that the wear of the cutting tool has a significant impact on the value of the cutting force components – when cutting at a speed of 350 m/min, the machining process with a tool of PcBN group BH obtained from coated powders, compared to machining with a tool of PcBN group BH obtained from uncoated powders, is characterized by a 15–20% lower value of the cutting force components. During high-speed machining under dynamic shock loads, a tool equipped with BH PcBN obtained from coated cBN powders, unlike cutters made of BL PcBN, retains its performance at a feed rate of 0, 38 mm/rev - usually, working under such conditions leads to brittle fracture of the tool equipped with PcBN of group BL due to chipping of individual fragments of the cutting edge from the back surface, and on the tool equipped with PcBN (5% Ti), there are separate traces of microchipping. The obtained research results indicate the possibility of using tools equipped with PcBN of group BH, sintered from coated cBN powders, under high-speed cutting conditions, which is typical for tools made of PcBN of group BL, but in the presence of dynamic loading.
- 27 December 2024
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National technical university "Kharkiv Polytechnic Institute" Series: Techniques in a machine industry
- No. 1(9),p. 13-18
Open AccessSTRENGTH FEATURES OF HARDENED STEEL TREATMENT BY TOOLS EQUIPPED WITH PcBN OF BH, BL GROUP
A set of studies has been carried out to investigate the power features of machining hardened steel with a tool equipped with PcBN of the VN group, obtained from the initial cBN powders coated with Ti and uncoated compounds, as well as PcBN of the BL group. The determined features of the machining process have shown that the wear of the cutting tool has a significant impact on the value of the cutting force components – when cutting at a speed of 350 m/min, the machining process with a tool of PcBN group BH obtained from coated powders, compared to machining with a tool of PcBN group BH obtained from uncoated powders, is characterized by a 15–20% lower value of the cutting force components. During high-speed machining under dynamic shock loads, a tool equipped with BH PcBN obtained from coated cBN powders, unlike cutters made of BL PcBN, retains its performance at a feed rate of 0, 38 mm/rev - usually, working under such conditions leads to brittle fracture of the tool equipped with PcBN of group BL due to chipping of individual fragments of the cutting edge from the back surface, and on the tool equipped with PcBN (5% Ti), there are separate traces of microchipping. The obtained research results indicate the possibility of using tools equipped with PcBN of group BH, sintered from coated cBN powders, under high-speed cutting conditions, which is typical for tools made of PcBN of group BL, but in the presence of dynamic loading.
- 1 January 2024
- Published by Chernihiv Polytechnic National University in TECHNICAL SCIENCES AND TECHNOLOGIES
- No. 3(37)
Багатошарові леговані нітридні покриття системи TiAlN
Наведено результати досліджень гами багатошарових наноструктурних покриттів на основі системи TiAlN – стру-ктурного стану, морфології, складу, мікрогеометрії інтерфейсу. Покриття загальною товщиною 7–8 мкм з товщиною ша-рів (TiAlN/СrN) 20–30 нм, нанесене вакуумно-дуговим методом на основу з надтвердої кераміки на основі кубічного нітриду бору. Розглянуто вплив на показники стану інтерфейсу покриттів легування їхніх матеріалів Y та Si, комплексом елементів – Y, Zr, Nb. На основі аналізу результатів вивчення інтерфейсу покриттів методом скетч-тестування встановлено агезійний і когезійний механізми руйнування покриттів залежно від рівня легування їхніх матеріалів, запропоновано перспективні напрями використання покриттів для застосування в різальному інструменті з PcBN
- 1 January 2024
- Published by Chernihiv Polytechnic National University in TECHNICAL SCIENCES AND TECHNOLOGIES
- No. 3(37)
Багатошарові леговані нітридні покриття системи TiAlN
Наведено результати досліджень гами багатошарових наноструктурних покриттів на основі системи TiAlN – стру-ктурного стану, морфології, складу, мікрогеометрії інтерфейсу. Покриття загальною товщиною 7–8 мкм з товщиною ша-рів (TiAlN/СrN) 20–30 нм, нанесене вакуумно-дуговим методом на основу з надтвердої кераміки на основі кубічного нітриду бору. Розглянуто вплив на показники стану інтерфейсу покриттів легування їхніх матеріалів Y та Si, комплексом елементів – Y, Zr, Nb. На основі аналізу результатів вивчення інтерфейсу покриттів методом скетч-тестування встановлено агезійний і когезійний механізми руйнування покриттів залежно від рівня легування їхніх матеріалів, запропоновано перспективні напрями використання покриттів для застосування в різальному інструменті з PcBN
- Open Access
- 1 January 2024
- Published by Chernihiv Polytechnic National University in TECHNICAL SCIENCES AND TECHNOLOGIES
- No. 1(35),p. 65-74
STRUCTURAL STATE OF COMPOSITES SINTERED FROM cBN POEDERS WITH A COATING OF COMPOUNDS Ti
The paper presents the results of experimental studies of the structural state of composites obtained at high temperatures and pressures from cBN powders with coatings deposited by CVD from Ti compounds using a gas transport reaction. The features and quantitative parameters of the structure of the composites depending on the presence of Ti in the coating were determined. It has been experimentally established that the matrices of the obtained composites are formed by submicron grains of TiN and TiB2, the quantitative differences of which correspond to the concentration of Ti in the coating - from 3 to 8 %. The structure of the obtained composites is characterized by a uniform distribution of the ceramic matrix between the cBN grains, which is achieved due to the high-quality encapsulation of individual grains of the superhard phase in the coating. The ceramic layers have the largest dimensions (up to 10-12 μm) in the area of triple joints, the width of the zone between two adjacent cBN particles is < 1 μm. When moving from a coated powder to a composite, the shape of the diffraction peaks changes, which is associated with the stresses of the first and/or second kind inherent in the studied samples. Sintering of the powder leads to a decrease in the size of the blocks from 56 nm to 27 nm, an increase in the lattice strain from 0.11 to 0.24 %, in TiN - to an increase in the lattice parameter in the composite by 10% (from 0.4244 nm to 0.4253 nm), a decrease in the size of crystallites within individual grains from 100 nm to 20 nm, and an increase in the lattice strain by 0.47 %. At the same time, TiN nitride is supersaturated with nitrogen, which is a significant increase in its lattice parameter, and the coating formed in this case is exclusively oriented in the (022) direction.
- 1 January 2024
- Published by Chernihiv Polytechnic National University in TECHNICAL SCIENCES AND TECHNOLOGIES
- No. 1(35),p. 65-74
Open AccessSTRUCTURAL STATE OF COMPOSITES SINTERED FROM cBN POEDERS WITH A COATING OF COMPOUNDS Ti
The paper presents the results of experimental studies of the structural state of composites obtained at high temperatures and pressures from cBN powders with coatings deposited by CVD from Ti compounds using a gas transport reaction. The features and quantitative parameters of the structure of the composites depending on the presence of Ti in the coating were determined. It has been experimentally established that the matrices of the obtained composites are formed by submicron grains of TiN and TiB2, the quantitative differences of which correspond to the concentration of Ti in the coating - from 3 to 8 %. The structure of the obtained composites is characterized by a uniform distribution of the ceramic matrix between the cBN grains, which is achieved due to the high-quality encapsulation of individual grains of the superhard phase in the coating. The ceramic layers have the largest dimensions (up to 10-12 μm) in the area of triple joints, the width of the zone between two adjacent cBN particles is < 1 μm. When moving from a coated powder to a composite, the shape of the diffraction peaks changes, which is associated with the stresses of the first and/or second kind inherent in the studied samples. Sintering of the powder leads to a decrease in the size of the blocks from 56 nm to 27 nm, an increase in the lattice strain from 0.11 to 0.24 %, in TiN - to an increase in the lattice parameter in the composite by 10% (from 0.4244 nm to 0.4253 nm), a decrease in the size of crystallites within individual grains from 100 nm to 20 nm, and an increase in the lattice strain by 0.47 %. At the same time, TiN nitride is supersaturated with nitrogen, which is a significant increase in its lattice parameter, and the coating formed in this case is exclusively oriented in the (022) direction.
- Open Access
- 20 September 2023
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National technical university "Kharkiv Polytechnic Institute" Series: Techniques in a machine industry
- No. 1(7),p. 16-21
EXERIMENTAL ESTIMATION OF HARD TURNING CONTACT CHARACTERISTICS
При обробці загартованої сталі інструментом з ПНТМ на основі КНБ в умовах близьких до ортогонального різання визначені сили різання в залежності від величини подачі та швидкості різання. Встановлено величину контактних напружень, коефіцієнту тертя та довжину контакту стружки з передньою поверхнею різця для швидкості різання 100 м/хв та отримано шліфи стружки, які демонструють морфологію стружки. Експериментально встановлено, що при обробці загартованої підшипникової сталі величина тангенійної та радиальної складових сили різання, що діють на передній поверхні інструменту при подачі 0,05 мм/об та швидкості різання 100 м/хв становить 125 Н/мм та 42 Н/мм відповідно. Середній коефіцієнт тертя при цьому становить 0,33. Показано, що для вимірювання довжини контакту стружки з передньою поверхнею різця доцільно використовувати тонкі металеві PVD покриття товщиною ~ 0,1 мкм, що дозволяє підвищити точність визначення даного параметру. Зразки стружки, отримані у досліджуваному діапазоні умов обробки свідчать про сегментний тип стружкоутворення. Вимірювання товщини стружки отриманої при подачі 0,05 мм/об та швидкості різання 100 м/хв мають товщину від 40 до 80 мкм.
- 20 September 2023
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National technical university "Kharkiv Polytechnic Institute" Series: Techniques in a machine industry
- No. 1(7),p. 16-21
Open AccessEXERIMENTAL ESTIMATION OF HARD TURNING CONTACT CHARACTERISTICS
При обробці загартованої сталі інструментом з ПНТМ на основі КНБ в умовах близьких до ортогонального різання визначені сили різання в залежності від величини подачі та швидкості різання. Встановлено величину контактних напружень, коефіцієнту тертя та довжину контакту стружки з передньою поверхнею різця для швидкості різання 100 м/хв та отримано шліфи стружки, які демонструють морфологію стружки. Експериментально встановлено, що при обробці загартованої підшипникової сталі величина тангенійної та радиальної складових сили різання, що діють на передній поверхні інструменту при подачі 0,05 мм/об та швидкості різання 100 м/хв становить 125 Н/мм та 42 Н/мм відповідно. Середній коефіцієнт тертя при цьому становить 0,33. Показано, що для вимірювання довжини контакту стружки з передньою поверхнею різця доцільно використовувати тонкі металеві PVD покриття товщиною ~ 0,1 мкм, що дозволяє підвищити точність визначення даного параметру. Зразки стружки, отримані у досліджуваному діапазоні умов обробки свідчать про сегментний тип стружкоутворення. Вимірювання товщини стружки отриманої при подачі 0,05 мм/об та швидкості різання 100 м/хв мають товщину від 40 до 80 мкм.
- Open Access
- 3 July 2023
- Published by Zhytomyr Polytechnic State University in Технічна інженерія
- No. 1(91),p. 17-25
Працездатність різального інструменту, оснащеного ПКНБ групи BL, при швидкісній обробці загартованої сталі
У роботі досліджувалися розроблені в Інституті надтвердих матеріалів ім. В.М. Бакуля інструменти з надтвердих матеріалів на основі КНБ групи BL, виготовлені з додаванням керамічних компонентів TaN, TiC, TiN. Такі матеріали класифікуються як керамоматричні композити (КМК). Твердість нових модифікацій композитів інструментального призначення становила від 31,2 до 40,2 ГПа. Експериментальні дослідження проводилися в умовах високошвидкісного різання загартованих сталей ШХ15 та ХВГ. Вивчалася працездатність надтвердих композитів за критерієм відсутності крихкого руйнування різальної кромки інструменту та ефективність нових композитів за критерієм мінімальної інтенсивності зношування задньої поверхні різців під час різання з режимами, що відповідають умовам фінішної обробки. Високі експлуатаційні параметри – якість оброки та мінімальна інтенсивність зношування – були продемонстровані інструментами, що оснащені КМК, які містять матрицю, утворену карбідом титану.
- 3 July 2023
- Published by Zhytomyr Polytechnic State University in Технічна інженерія
- No. 1(91),p. 17-25
Open AccessПрацездатність різального інструменту, оснащеного ПКНБ групи BL, при швидкісній обробці загартованої сталі
У роботі досліджувалися розроблені в Інституті надтвердих матеріалів ім. В.М. Бакуля інструменти з надтвердих матеріалів на основі КНБ групи BL, виготовлені з додаванням керамічних компонентів TaN, TiC, TiN. Такі матеріали класифікуються як керамоматричні композити (КМК). Твердість нових модифікацій композитів інструментального призначення становила від 31,2 до 40,2 ГПа. Експериментальні дослідження проводилися в умовах високошвидкісного різання загартованих сталей ШХ15 та ХВГ. Вивчалася працездатність надтвердих композитів за критерієм відсутності крихкого руйнування різальної кромки інструменту та ефективність нових композитів за критерієм мінімальної інтенсивності зношування задньої поверхні різців під час різання з режимами, що відповідають умовам фінішної обробки. Високі експлуатаційні параметри – якість оброки та мінімальна інтенсивність зношування – були продемонстровані інструментами, що оснащені КМК, які містять матрицю, утворену карбідом титану.
- Open Access
- 28 July 2022
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National technical university "Kharkiv Polytechnic Institute" Series: Techniques in a machine industry
- No. 1,p. 3-9
SIMULATION OF THE STATE OF THE CHIP FORMATION ZONE DURING FACE MILLING OF HARDENED STEEL
The article considers the results of modeling the stress-strain and thermal state of the cutting zone during face milling of hardened steel with a tool equipped with polycrystalline superhard composite based on cubic boron nitride. The influence of strengthening the surface layer of the processed material, characteristic for different passes of different tools, on the cutting forces, shrinkage of chips, the length of contact of chips with the front surface of the tool is shown. The connection of non-stationary nature of machining with incisions of each of the tool blades and exit from the cutting zone with the presence of periods of increase in cutting temperature and cooling of the cutting tool has been studied.
- 28 July 2022
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National technical university "Kharkiv Polytechnic Institute" Series: Techniques in a machine industry
- No. 1,p. 3-9
Open AccessSIMULATION OF THE STATE OF THE CHIP FORMATION ZONE DURING FACE MILLING OF HARDENED STEEL
The article considers the results of modeling the stress-strain and thermal state of the cutting zone during face milling of hardened steel with a tool equipped with polycrystalline superhard composite based on cubic boron nitride. The influence of strengthening the surface layer of the processed material, characteristic for different passes of different tools, on the cutting forces, shrinkage of chips, the length of contact of chips with the front surface of the tool is shown. The connection of non-stationary nature of machining with incisions of each of the tool blades and exit from the cutting zone with the presence of periods of increase in cutting temperature and cooling of the cutting tool has been studied.
- Open Access
- 15 June 2021
- Published by National Technical University Kharkiv Polytechnic Institute in Cutting & Tools in Technological System
- No. 94,p. 102-114
FINISH MACHINING OF THE CUTTING INSERTS FROM CUBIC BORINE NITRIDE BL GROUP COMPOSITE
Finishing methods of machining of superhard composite’s working elements based on cubic boron nitride BL group are considered. The results of the microgeometry formation research of the cutting inserts’ surfaces during machining by free powders of synthetic diamond, grinding wheels and a method of vibro-magnetic-abrasive machining (VMAM) are presented. It is shown that during VMAM the friction between the inserts’ surfaces and the abrasive particles result in microremoval of the material, which reduces the roughness of the cutting inserts’ surfaces. It is established that additional fine grinding with 14/10 mkm synthetic diamond powder provides the absence of microgeometry defects of the cutting inserts’ surfaces left by pre-machining. The result of high-quality rounding of cutting edges and the formation of surfaces of cutting inserts with less roughness is an increase in strength and wear resistance of metal-cutting tools in high-speed machining under conditions of significant loads.
- 15 June 2021
- Published by National Technical University Kharkiv Polytechnic Institute in Cutting & Tools in Technological System
- No. 94,p. 102-114
Open AccessFINISH MACHINING OF THE CUTTING INSERTS FROM CUBIC BORINE NITRIDE BL GROUP COMPOSITE
Finishing methods of machining of superhard composite’s working elements based on cubic boron nitride BL group are considered. The results of the microgeometry formation research of the cutting inserts’ surfaces during machining by free powders of synthetic diamond, grinding wheels and a method of vibro-magnetic-abrasive machining (VMAM) are presented. It is shown that during VMAM the friction between the inserts’ surfaces and the abrasive particles result in microremoval of the material, which reduces the roughness of the cutting inserts’ surfaces. It is established that additional fine grinding with 14/10 mkm synthetic diamond powder provides the absence of microgeometry defects of the cutting inserts’ surfaces left by pre-machining. The result of high-quality rounding of cutting edges and the formation of surfaces of cutting inserts with less roughness is an increase in strength and wear resistance of metal-cutting tools in high-speed machining under conditions of significant loads.
- 1 November 2018
- Published by Allerton Press in Journal of Superhard Materials
- Vol. 40 (6) , 424-431
Promising Types of Coatings for PCBN Tools
The paper reviews the present-day trends in the development of new types of wear-resistant coatings, including nanostructured ones, for PCBN tools. The main currently pursued approaches to creation...
- 1 November 2018
- Published by Allerton Press in Journal of Superhard Materials
- Vol. 40 (6) , 424-431
Promising Types of Coatings for PCBN Tools
The paper reviews the present-day trends in the development of new types of wear-resistant coatings, including nanostructured ones, for PCBN tools. The main currently pursued approaches to creation...
- 1 July 2017
- Published by Allerton Press in Journal of Superhard Materials
- Vol. 39 (4) , 288-297
Special features of the applications of cutting tools from polycrystalline cubic boron nitride with protective coatings
The results of the investigations on the efficiency of cutting tools from polycrystalline superhard materials based on cubic boron nitride with a protective coating. A hypothesis is proposed for the...
- 1 July 2017
- Published by Allerton Press in Journal of Superhard Materials
- Vol. 39 (4) , 288-297
Special features of the applications of cutting tools from polycrystalline cubic boron nitride with protective coatings
The results of the investigations on the efficiency of cutting tools from polycrystalline superhard materials based on cubic boron nitride with a protective coating. A hypothesis is proposed for the...
- 1 July 2015
- Published by Springer Nature in Powder Metallurgy and Metal Ceramics
- Vol. 54 (3-4) , 140-150
Formation of a Tribofilm in the Surface Layer of Al–Ti–Cr–N–B Magnetron Coating on Boron Nitride During Turning of Hardened Steel
- 1 July 2015
- Published by Springer Nature in Powder Metallurgy and Metal Ceramics
- Vol. 54 (3-4) , 140-150
Formation of a Tribofilm in the Surface Layer of Al–Ti–Cr–N–B Magnetron Coating on Boron Nitride During Turning of Hardened Steel