Yurii Melniychuk
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yurii Melniychuk has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Anatolii Chumak
Інститут надтвердих матеріалів ім. В. М. Бакуля НАН України
3 shared publications - Andrey Manokhin
Bakul Institute for Superhard Materials, National Academy of Sciences of Ukraine, Kyiv, Ukraine
3 shared publications - S. An. Klimenko
Інститут надтвердих матеріалів ім. В. М. Бакуля НАН України
3 shared publications - Marina Kopeikina
Інститут надтвердих матеріалів ім. В.М. Бакуля Національної академії наук України
2 shared publications Serhii Klymenko
2 shared publications- Юрій Олексійович Мельнійчук
Інститут надтвердих матеріалів ім. В.М. Бакуля НАН України
2 shared publications
Latest Publications
- Open Access
- 27 December 2024
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National technical university "Kharkiv Polytechnic Institute" Series: Techniques in a machine industry
- No. 1(9),p. 13-18
STRENGTH FEATURES OF HARDENED STEEL TREATMENT BY TOOLS EQUIPPED WITH PcBN OF BH, BL GROUP
A set of studies has been carried out to investigate the power features of machining hardened steel with a tool equipped with PcBN of the VN group, obtained from the initial cBN powders coated with Ti and uncoated compounds, as well as PcBN of the BL group. The determined features of the machining process have shown that the wear of the cutting tool has a significant impact on the value of the cutting force components – when cutting at a speed of 350 m/min, the machining process with a tool of PcBN group BH obtained from coated powders, compared to machining with a tool of PcBN group BH obtained from uncoated powders, is characterized by a 15–20% lower value of the cutting force components. During high-speed machining under dynamic shock loads, a tool equipped with BH PcBN obtained from coated cBN powders, unlike cutters made of BL PcBN, retains its performance at a feed rate of 0, 38 mm/rev - usually, working under such conditions leads to brittle fracture of the tool equipped with PcBN of group BL due to chipping of individual fragments of the cutting edge from the back surface, and on the tool equipped with PcBN (5% Ti), there are separate traces of microchipping. The obtained research results indicate the possibility of using tools equipped with PcBN of group BH, sintered from coated cBN powders, under high-speed cutting conditions, which is typical for tools made of PcBN of group BL, but in the presence of dynamic loading.
- 27 December 2024
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National technical university "Kharkiv Polytechnic Institute" Series: Techniques in a machine industry
- No. 1(9),p. 13-18
Open AccessSTRENGTH FEATURES OF HARDENED STEEL TREATMENT BY TOOLS EQUIPPED WITH PcBN OF BH, BL GROUP
A set of studies has been carried out to investigate the power features of machining hardened steel with a tool equipped with PcBN of the VN group, obtained from the initial cBN powders coated with Ti and uncoated compounds, as well as PcBN of the BL group. The determined features of the machining process have shown that the wear of the cutting tool has a significant impact on the value of the cutting force components – when cutting at a speed of 350 m/min, the machining process with a tool of PcBN group BH obtained from coated powders, compared to machining with a tool of PcBN group BH obtained from uncoated powders, is characterized by a 15–20% lower value of the cutting force components. During high-speed machining under dynamic shock loads, a tool equipped with BH PcBN obtained from coated cBN powders, unlike cutters made of BL PcBN, retains its performance at a feed rate of 0, 38 mm/rev - usually, working under such conditions leads to brittle fracture of the tool equipped with PcBN of group BL due to chipping of individual fragments of the cutting edge from the back surface, and on the tool equipped with PcBN (5% Ti), there are separate traces of microchipping. The obtained research results indicate the possibility of using tools equipped with PcBN of group BH, sintered from coated cBN powders, under high-speed cutting conditions, which is typical for tools made of PcBN of group BL, but in the presence of dynamic loading.
- Open Access
Binderless Polycrystalline Cubic Boron Nitride Sintered Compacts for Machining of Cemented Carbides
High-purity, superhard, binderless polycrystalline cubic boron nitride (BL-PCBN) was obtained by direct hBN to cBN transformation in a toroid-type high-pressure apparatus at a pressure of 8.0 GPa and temperature of 2250 °C (HPHT-DCS; high-pressure, high-temperature direct conversion sintering). X-ray diffraction analysis revealed a prominent [111] axial texture in the sintered material when the axis was oriented perpendicular to the end surface of the sample. Vickers hardness tests conducted at a load of 49 N showed that BL-PCBN possessed an exceptional hardness value of 63.4 GPa. Finally, cutting tools made of BL-PCBN and SN-PCBN (Si3N4-doped cBN-based composite) reference materials were tested during the turning of a cemented tungsten carbide workpiece. The results of the cutting tests demonstrated that the wear resistance of the BL-PCBN material obtained with the HPHT-DCS process is 1.5–1.9 times higher compared to the conventional SN-PCBN material, suggesting its significant potential for industrial application.
Open AccessBinderless Polycrystalline Cubic Boron Nitride Sintered Compacts for Machining of Cemented Carbides
High-purity, superhard, binderless polycrystalline cubic boron nitride (BL-PCBN) was obtained by direct hBN to cBN transformation in a toroid-type high-pressure apparatus at a pressure of 8.0 GPa and temperature of 2250 °C (HPHT-DCS; high-pressure, high-temperature direct conversion sintering). X-ray diffraction analysis revealed a prominent [111] axial texture in the sintered material when the axis was oriented perpendicular to the end surface of the sample. Vickers hardness tests conducted at a load of 49 N showed that BL-PCBN possessed an exceptional hardness value of 63.4 GPa. Finally, cutting tools made of BL-PCBN and SN-PCBN (Si3N4-doped cBN-based composite) reference materials were tested during the turning of a cemented tungsten carbide workpiece. The results of the cutting tests demonstrated that the wear resistance of the BL-PCBN material obtained with the HPHT-DCS process is 1.5–1.9 times higher compared to the conventional SN-PCBN material, suggesting its significant potential for industrial application.
- Open Access
- 1 January 2024
- Published by Chernihiv Polytechnic National University in TECHNICAL SCIENCES AND TECHNOLOGIES
- No. 1(35),p. 65-74
STRUCTURAL STATE OF COMPOSITES SINTERED FROM cBN POEDERS WITH A COATING OF COMPOUNDS Ti
The paper presents the results of experimental studies of the structural state of composites obtained at high temperatures and pressures from cBN powders with coatings deposited by CVD from Ti compounds using a gas transport reaction. The features and quantitative parameters of the structure of the composites depending on the presence of Ti in the coating were determined. It has been experimentally established that the matrices of the obtained composites are formed by submicron grains of TiN and TiB2, the quantitative differences of which correspond to the concentration of Ti in the coating - from 3 to 8 %. The structure of the obtained composites is characterized by a uniform distribution of the ceramic matrix between the cBN grains, which is achieved due to the high-quality encapsulation of individual grains of the superhard phase in the coating. The ceramic layers have the largest dimensions (up to 10-12 μm) in the area of triple joints, the width of the zone between two adjacent cBN particles is < 1 μm. When moving from a coated powder to a composite, the shape of the diffraction peaks changes, which is associated with the stresses of the first and/or second kind inherent in the studied samples. Sintering of the powder leads to a decrease in the size of the blocks from 56 nm to 27 nm, an increase in the lattice strain from 0.11 to 0.24 %, in TiN - to an increase in the lattice parameter in the composite by 10% (from 0.4244 nm to 0.4253 nm), a decrease in the size of crystallites within individual grains from 100 nm to 20 nm, and an increase in the lattice strain by 0.47 %. At the same time, TiN nitride is supersaturated with nitrogen, which is a significant increase in its lattice parameter, and the coating formed in this case is exclusively oriented in the (022) direction.
- 1 January 2024
- Published by Chernihiv Polytechnic National University in TECHNICAL SCIENCES AND TECHNOLOGIES
- No. 1(35),p. 65-74
Open AccessSTRUCTURAL STATE OF COMPOSITES SINTERED FROM cBN POEDERS WITH A COATING OF COMPOUNDS Ti
The paper presents the results of experimental studies of the structural state of composites obtained at high temperatures and pressures from cBN powders with coatings deposited by CVD from Ti compounds using a gas transport reaction. The features and quantitative parameters of the structure of the composites depending on the presence of Ti in the coating were determined. It has been experimentally established that the matrices of the obtained composites are formed by submicron grains of TiN and TiB2, the quantitative differences of which correspond to the concentration of Ti in the coating - from 3 to 8 %. The structure of the obtained composites is characterized by a uniform distribution of the ceramic matrix between the cBN grains, which is achieved due to the high-quality encapsulation of individual grains of the superhard phase in the coating. The ceramic layers have the largest dimensions (up to 10-12 μm) in the area of triple joints, the width of the zone between two adjacent cBN particles is < 1 μm. When moving from a coated powder to a composite, the shape of the diffraction peaks changes, which is associated with the stresses of the first and/or second kind inherent in the studied samples. Sintering of the powder leads to a decrease in the size of the blocks from 56 nm to 27 nm, an increase in the lattice strain from 0.11 to 0.24 %, in TiN - to an increase in the lattice parameter in the composite by 10% (from 0.4244 nm to 0.4253 nm), a decrease in the size of crystallites within individual grains from 100 nm to 20 nm, and an increase in the lattice strain by 0.47 %. At the same time, TiN nitride is supersaturated with nitrogen, which is a significant increase in its lattice parameter, and the coating formed in this case is exclusively oriented in the (022) direction.
- Open Access
- 20 September 2023
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National technical university "Kharkiv Polytechnic Institute" Series: Techniques in a machine industry
- No. 1(7),p. 16-21
EXERIMENTAL ESTIMATION OF HARD TURNING CONTACT CHARACTERISTICS
При обробці загартованої сталі інструментом з ПНТМ на основі КНБ в умовах близьких до ортогонального різання визначені сили різання в залежності від величини подачі та швидкості різання. Встановлено величину контактних напружень, коефіцієнту тертя та довжину контакту стружки з передньою поверхнею різця для швидкості різання 100 м/хв та отримано шліфи стружки, які демонструють морфологію стружки. Експериментально встановлено, що при обробці загартованої підшипникової сталі величина тангенійної та радиальної складових сили різання, що діють на передній поверхні інструменту при подачі 0,05 мм/об та швидкості різання 100 м/хв становить 125 Н/мм та 42 Н/мм відповідно. Середній коефіцієнт тертя при цьому становить 0,33. Показано, що для вимірювання довжини контакту стружки з передньою поверхнею різця доцільно використовувати тонкі металеві PVD покриття товщиною ~ 0,1 мкм, що дозволяє підвищити точність визначення даного параметру. Зразки стружки, отримані у досліджуваному діапазоні умов обробки свідчать про сегментний тип стружкоутворення. Вимірювання товщини стружки отриманої при подачі 0,05 мм/об та швидкості різання 100 м/хв мають товщину від 40 до 80 мкм.
- 20 September 2023
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National technical university "Kharkiv Polytechnic Institute" Series: Techniques in a machine industry
- No. 1(7),p. 16-21
Open AccessEXERIMENTAL ESTIMATION OF HARD TURNING CONTACT CHARACTERISTICS
При обробці загартованої сталі інструментом з ПНТМ на основі КНБ в умовах близьких до ортогонального різання визначені сили різання в залежності від величини подачі та швидкості різання. Встановлено величину контактних напружень, коефіцієнту тертя та довжину контакту стружки з передньою поверхнею різця для швидкості різання 100 м/хв та отримано шліфи стружки, які демонструють морфологію стружки. Експериментально встановлено, що при обробці загартованої підшипникової сталі величина тангенійної та радиальної складових сили різання, що діють на передній поверхні інструменту при подачі 0,05 мм/об та швидкості різання 100 м/хв становить 125 Н/мм та 42 Н/мм відповідно. Середній коефіцієнт тертя при цьому становить 0,33. Показано, що для вимірювання довжини контакту стружки з передньою поверхнею різця доцільно використовувати тонкі металеві PVD покриття товщиною ~ 0,1 мкм, що дозволяє підвищити точність визначення даного параметру. Зразки стружки, отримані у досліджуваному діапазоні умов обробки свідчать про сегментний тип стружкоутворення. Вимірювання товщини стружки отриманої при подачі 0,05 мм/об та швидкості різання 100 м/хв мають товщину від 40 до 80 мкм.