Evgeney Eduardovich Gusev
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Evgeney Eduardovich Gusev has a total of 65 co-authors. Here are the top co-authors by number of shared publications:
- Anna A. Dedkova
National Research University of Electronic Technology (MIET), Zelenograd, Russia
13 shared publications - Gleb Dmitrievich Demin
National Research University of Electronic Technology (MIET), Moscow, Zelenograd, Russia
5 shared publications N. A. Djuzhev
National Research University of Electronic Technology (MIET), Zelenograd, Russia
5 shared publicationsM. A. Makhiboroda
National Research University of Electronic Technology (MIET), Zelenograd, Russia
4 shared publicationsN. A. Dyuzhev
National Research University of Electronic Technology (MIET), Zelenograd, Russia
4 shared publications- Nikolay Alekseevich Djuzhev
MEMSEC R&D Center, National Research University of Electronic Technology (MIET), 124498 Moscow, Russia
4 shared publications
Latest Publications
- 1 April 2025
- Published by Pleiades Publishing Ltd in Mechanics of Solids
- Vol. 60 (2) , 839-847
Multifunctional Shuttle for Processing Small Diameter and Ultra-Thin Semiconductor Wafers
In a first for Russia, a 100 mm diameter wafer was processed to create holes for TSV structures using automated equipment designed for 150 mm diameter wafers without needing to reconfigure the installations. A shuttle wafer was developed for this purpose. The reliability of the silicon shuttle was determined through experimental studies of the mechanical strength of silicon. The thickness of the ultra-thin Si wafer that can be processed without damage in the shuttle wafer on installations with a vacuum table was calculated based on the data obtained.
- 1 April 2025
- Published by Pleiades Publishing Ltd in Mechanics of Solids
- Vol. 60 (2) , 839-847
Multifunctional Shuttle for Processing Small Diameter and Ultra-Thin Semiconductor Wafers
In a first for Russia, a 100 mm diameter wafer was processed to create holes for TSV structures using automated equipment designed for 150 mm diameter wafers without needing to reconfigure the installations. A shuttle wafer was developed for this purpose. The reliability of the silicon shuttle was determined through experimental studies of the mechanical strength of silicon. The thickness of the ultra-thin Si wafer that can be processed without damage in the shuttle wafer on installations with a vacuum table was calculated based on the data obtained.
- 21 March 2025
- Published by Technosphera JSC in Nanoindustry Russia
- Vol. 18 (2) , 148-159
ОЦЕНКА ВЛИЯНИЯ ИОННОЙ ОБРАБОТКИ НА ВЕЛИЧИНУ ОСТАТОЧНЫХ МЕХАНИЧЕСКИХ НАПРЯЖЕНИЙ В Al2O3/Si
Представлены результаты исследования влияния времени ионной обработки тонкопленочного покрытия Al2O3, сформированного на кремниевой подложке, на величину остаточных напряжений в интерфейсе "пленка – подложка". Ионное травление пленки осуществляется ионами аргона из источника Пеннинга. Впервые показана взаимосвязь формы подложки и уровня механических напряжений после обработки покрытия Al2O3 источником ионов. Показано негативное влияние обработки диэлектрического покрытия Al2O3 высокоэнергетическим потоком ионов аргона на внешний вид пленки.
- 21 March 2025
- Published by Technosphera JSC in Nanoindustry Russia
- Vol. 18 (2) , 148-159
ОЦЕНКА ВЛИЯНИЯ ИОННОЙ ОБРАБОТКИ НА ВЕЛИЧИНУ ОСТАТОЧНЫХ МЕХАНИЧЕСКИХ НАПРЯЖЕНИЙ В Al2O3/Si
Представлены результаты исследования влияния времени ионной обработки тонкопленочного покрытия Al2O3, сформированного на кремниевой подложке, на величину остаточных напряжений в интерфейсе "пленка – подложка". Ионное травление пленки осуществляется ионами аргона из источника Пеннинга. Впервые показана взаимосвязь формы подложки и уровня механических напряжений после обработки покрытия Al2O3 источником ионов. Показано негативное влияние обработки диэлектрического покрытия Al2O3 высокоэнергетическим потоком ионов аргона на внешний вид пленки.
- 18 September 2024
- Published by Technosphera JSC in Nanoindustry Russia
- Vol. 17 (6) , 372-381
ОЦЕНКА ВЛИЯНИЯ ТОЛЩИНЫ ПОКРЫТИЯ НА ВЕЛИЧИНУ ОСТАТОЧНЫХ МЕХАНИЧЕСКИХ НАПРЯЖЕНИЙ В AL2O3/Si
Представлены результаты исследования влияния толщины тонкопленочных покрытий на величину остаточных напряжений в интерфейсе пленка–подложка. В процессе эксперимента использована Si-подложка с тонкой пленкой Al2O3, сформированной магнетронным способом. Впервые показана взаимосвязь формы подложки и уровня остаточных напряжений в тонкопленочном покрытии. Применена модернизированная методика исследования остаточных напряжений в тонкопленочных покрытиях, позволяющая определять механические напряжения в локальных областях тонкой пленки.
- 18 September 2024
- Published by Technosphera JSC in Nanoindustry Russia
- Vol. 17 (6) , 372-381
ОЦЕНКА ВЛИЯНИЯ ТОЛЩИНЫ ПОКРЫТИЯ НА ВЕЛИЧИНУ ОСТАТОЧНЫХ МЕХАНИЧЕСКИХ НАПРЯЖЕНИЙ В AL2O3/Si
Представлены результаты исследования влияния толщины тонкопленочных покрытий на величину остаточных напряжений в интерфейсе пленка–подложка. В процессе эксперимента использована Si-подложка с тонкой пленкой Al2O3, сформированной магнетронным способом. Впервые показана взаимосвязь формы подложки и уровня остаточных напряжений в тонкопленочном покрытии. Применена модернизированная методика исследования остаточных напряжений в тонкопленочных покрытиях, позволяющая определять механические напряжения в локальных областях тонкой пленки.
- 1 April 2024
- Published by Pleiades Publishing Ltd in Mechanics of Solids
- Vol. 59 (2) , 746-753
Influence of Cyclic Loading on Physical and Mechanical Properties of Thin-Film Membrane Structures
The principle of modifying the mechanical properties of thin-film membrane structures of arbitrary shape by a non-contact method was proposed, implemented and explained for the first time. The idea was tested on a thin-film aluminum membrane formed by the magnetron method on a silicon substrate. The external influence was carried out through a cyclic load in the form of releasing and supplying excess air pressure to the membrane. As a result of repeated impacts, the physical properties of materials (grain size and roughness) and mechanical properties (internal mechanical stresses and critical overpressure) change. Changing the magnitude of residual mechanical stresses in the membrane material allows the formation of a surface with the required curvature value. In this work, after a cyclic load with a pressure equal to half the critical pressure, the following effects were revealed: the deflection of the membrane in the absence of external influence increased by more than an order of magnitude, the structure passed into a plastic type of deformation, the critical burst pressure decreased by several tens of percent. The use of this methodology makes it possible to create new materials with unique mechanical properties.
- 1 April 2024
- Published by Pleiades Publishing Ltd in Mechanics of Solids
- Vol. 59 (2) , 746-753
Influence of Cyclic Loading on Physical and Mechanical Properties of Thin-Film Membrane Structures
The principle of modifying the mechanical properties of thin-film membrane structures of arbitrary shape by a non-contact method was proposed, implemented and explained for the first time. The idea was tested on a thin-film aluminum membrane formed by the magnetron method on a silicon substrate. The external influence was carried out through a cyclic load in the form of releasing and supplying excess air pressure to the membrane. As a result of repeated impacts, the physical properties of materials (grain size and roughness) and mechanical properties (internal mechanical stresses and critical overpressure) change. Changing the magnitude of residual mechanical stresses in the membrane material allows the formation of a surface with the required curvature value. In this work, after a cyclic load with a pressure equal to half the critical pressure, the following effects were revealed: the deflection of the membrane in the absence of external influence increased by more than an order of magnitude, the structure passed into a plastic type of deformation, the critical burst pressure decreased by several tens of percent. The use of this methodology makes it possible to create new materials with unique mechanical properties.
- 1 April 2024
- Published by Pleiades Publishing Ltd in Nanobiotechnology Reports
- Vol. 19 (2) , 197-207
Technology for Manufacturing TSV Structures for the Creation of Silicon Interposers Using Temporary-Bonding Technology
For the first time in Russia, we present a technology for temporary wafer bonding, which is used to form through holes in silicon (through-silica via (TSV) structures) with a high aspect ratio of depth to diameter (more than 10 to 1), as well as a method for transferring alignment marks from the front to the back side of a thin Si wafer, consisting in the use of a glass carrier plate, which allows for a sufficient amount of deflection of the assembly for lithography. The modernized operating parameters of Si-glass bonding, which consist in controlling the cooling rate of the plates and applying pressure to the plates during their cooling phase, ensure a reduction in the deflection of the resulting assembly by 75% before thinning and by 65% after thinning to a residual thickness of 125 μm while maintaining the mechanical integrity of the plates.
- 1 April 2024
- Published by Pleiades Publishing Ltd in Nanobiotechnology Reports
- Vol. 19 (2) , 197-207
Technology for Manufacturing TSV Structures for the Creation of Silicon Interposers Using Temporary-Bonding Technology
For the first time in Russia, we present a technology for temporary wafer bonding, which is used to form through holes in silicon (through-silica via (TSV) structures) with a high aspect ratio of depth to diameter (more than 10 to 1), as well as a method for transferring alignment marks from the front to the back side of a thin Si wafer, consisting in the use of a glass carrier plate, which allows for a sufficient amount of deflection of the assembly for lithography. The modernized operating parameters of Si-glass bonding, which consist in controlling the cooling rate of the plates and applying pressure to the plates during their cooling phase, ensure a reduction in the deflection of the resulting assembly by 75% before thinning and by 65% after thinning to a residual thickness of 125 μm while maintaining the mechanical integrity of the plates.
- 1 February 2024
- Published by Pleiades Publishing Ltd in Mechanics of Solids
- Vol. 59 (1) , 20-26
Study of the Effect of Radiation Exposure on Grain Size and Mechanical Properties of Thin-Film Aluminum
For the first time, an experimental dependence of the grain size and mechanical properties of a thin-film aluminum material on the dose of short-wave radiation has been obtained. A thin film of aluminum was formed on a silicon substrate using magnetron sputtering. The effect of a decrease in mechanical strength and biaxial elastic modulus with increasing radiation dose was identified. This effect is explained by a decrease in grain size and roughness on a thin-film aluminum membrane. For the microscopically measured range of aluminum grain sizes, the inverse Hall-Petch relation is used. During the research, it was determined that during irradiation the number of grain boundaries and the number of grains themselves increases, which leads to an increase in the likelihood of deformation.
- 1 February 2024
- Published by Pleiades Publishing Ltd in Mechanics of Solids
- Vol. 59 (1) , 20-26
Study of the Effect of Radiation Exposure on Grain Size and Mechanical Properties of Thin-Film Aluminum
For the first time, an experimental dependence of the grain size and mechanical properties of a thin-film aluminum material on the dose of short-wave radiation has been obtained. A thin film of aluminum was formed on a silicon substrate using magnetron sputtering. The effect of a decrease in mechanical strength and biaxial elastic modulus with increasing radiation dose was identified. This effect is explained by a decrease in grain size and roughness on a thin-film aluminum membrane. For the microscopically measured range of aluminum grain sizes, the inverse Hall-Petch relation is used. During the research, it was determined that during irradiation the number of grain boundaries and the number of grains themselves increases, which leads to an increase in the likelihood of deformation.
- Open Access
Deformations of Single-Crystal Silicon Circular Plate: Theory and Experiment
In this paper, the experimental methodology for the single-crystal circular plate deformation measurement and subsequent procedure for the quantitation of its mechanical properties are developed. The procedure is based on a new numerical-analytical solution of non-linear boundary-value problem for finite deformations of a circular anisotropic plate. Using the developed method, a study of the deformation of single-crystal circular plates formed on the basis of a silicon-on-insulator structure was carried out. The values of residual stresses are determined and it is shown that the presence of these stresses increases the flexural rigidity of the plate by several times.
Open AccessDeformations of Single-Crystal Silicon Circular Plate: Theory and Experiment
In this paper, the experimental methodology for the single-crystal circular plate deformation measurement and subsequent procedure for the quantitation of its mechanical properties are developed. The procedure is based on a new numerical-analytical solution of non-linear boundary-value problem for finite deformations of a circular anisotropic plate. Using the developed method, a study of the deformation of single-crystal circular plates formed on the basis of a silicon-on-insulator structure was carried out. The values of residual stresses are determined and it is shown that the presence of these stresses increases the flexural rigidity of the plate by several times.
- Open Access
- 26 December 2023
- Published by MDPI AG in Preprints.org
Deformations of Single-Crystal Silicon Circular Plate: Theory and Experiment
In the paper the experimental methodology for the single-crystal circular plate deformation measurement and subsequent procedure for mechanical properties quantitation are developed. The procedure is based on a new numerical-analytical solution of nonlinear boundary-value problem for finite deformations of a circular anisotropic plate. Using the developed method, a study of the deformation of single-crystal circular plates formed on the basis of a silicon-on-insulator structure was carried out. The values of residual stresses are determined and it is shown that the presence of these stresses increases the flexural rigidity of the plate in several times.
- 26 December 2023
- Published by MDPI AG in Preprints.org
Open AccessDeformations of Single-Crystal Silicon Circular Plate: Theory and Experiment
In the paper the experimental methodology for the single-crystal circular plate deformation measurement and subsequent procedure for mechanical properties quantitation are developed. The procedure is based on a new numerical-analytical solution of nonlinear boundary-value problem for finite deformations of a circular anisotropic plate. Using the developed method, a study of the deformation of single-crystal circular plates formed on the basis of a silicon-on-insulator structure was carried out. The values of residual stresses are determined and it is shown that the presence of these stresses increases the flexural rigidity of the plate in several times.
- 18 October 2022
- Published by Allerton Press in Mechanics of Solids
- Vol. 57 (5) , 1044-1053
Study of the Mechanical Properties of Thin-Film Membranes Made of Oxide and Silicon Nitride
Thin-film membranes are made from alternating layers of silicon oxide and silicon nitride using a group technology. The influence of the number of layers c
- 18 October 2022
- Published by Allerton Press in Mechanics of Solids
- Vol. 57 (5) , 1044-1053
Study of the Mechanical Properties of Thin-Film Membranes Made of Oxide and Silicon Nitride
Thin-film membranes are made from alternating layers of silicon oxide and silicon nitride using a group technology. The influence of the number of layers c
- 1 January 2022
- Published by Ioffe Institute Russian Academy of Sciences in Technical Physics
- Vol. 92 (13) , 2033
Peculiarities of deformation of round thin-film membranes and experimental determination of their effective characteristics
The features of thin-film membranes, which are formed above round holes in silicon substrates using the Bosch-process are considered. The membrane has a complex shape due to the presence of the stress state of the initial films. The analysis of the dependence of the membrane deflection w on the supplied overpressure P is used to calculate the mechanical characteristics of the membranes. In this case, it is necessary to determine directly on the membrane its diameter, the thickness of the constituent layers, the change in the topography of the membrane surface over its entire area as the overpressure increases. Determination of the membrane diameter and the thicknesses of the constituent layers is shown by the example of p-Si*/SiNx/SiO2 and SiNx/SiO2/SiNx/SiO2 membranes. We used spectral ellipsometry, energy-dispersive X-ray spectroscopy, optical profilometry, optical microscopy. The influence of the peculiarities of the fixing conditions on the stress-strain state of membranes is shown, and the assessment is carried out by means of numerical modeling. A technique has been developed for measuring and calculating the mechanical characteristics of membranes that have an initial deflection. The calculation result is shown on the example of a membrane with an initial deflection of 2 μm --- SiNx/SiO2/SiNx/SiO2 and a membrane with an initial deflection of 30 μm --- Al/SiO2/Al. Keywords: stress, bulging method, films, thin-layer coating, film thickness, membrane, pressure blister test, residual stress, microelectromechanical systems, MEMS, silicon substrate, large deformations, strain, deflections, circular membrane, bulge testing.
- 1 January 2022
- Published by Ioffe Institute Russian Academy of Sciences in Technical Physics
- Vol. 92 (13) , 2033
Peculiarities of deformation of round thin-film membranes and experimental determination of their effective characteristics
The features of thin-film membranes, which are formed above round holes in silicon substrates using the Bosch-process are considered. The membrane has a complex shape due to the presence of the stress state of the initial films. The analysis of the dependence of the membrane deflection w on the supplied overpressure P is used to calculate the mechanical characteristics of the membranes. In this case, it is necessary to determine directly on the membrane its diameter, the thickness of the constituent layers, the change in the topography of the membrane surface over its entire area as the overpressure increases. Determination of the membrane diameter and the thicknesses of the constituent layers is shown by the example of p-Si*/SiNx/SiO2 and SiNx/SiO2/SiNx/SiO2 membranes. We used spectral ellipsometry, energy-dispersive X-ray spectroscopy, optical profilometry, optical microscopy. The influence of the peculiarities of the fixing conditions on the stress-strain state of membranes is shown, and the assessment is carried out by means of numerical modeling. A technique has been developed for measuring and calculating the mechanical characteristics of membranes that have an initial deflection. The calculation result is shown on the example of a membrane with an initial deflection of 2 μm --- SiNx/SiO2/SiNx/SiO2 and a membrane with an initial deflection of 30 μm --- Al/SiO2/Al. Keywords: stress, bulging method, films, thin-layer coating, film thickness, membrane, pressure blister test, residual stress, microelectromechanical systems, MEMS, silicon substrate, large deformations, strain, deflections, circular membrane, bulge testing.