Iliya L. Panov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Iliya L. Panov has a total of 38 co-authors. Here are the top co-authors by number of shared publications:
- Sergey Victorovich Panin
Institute of Strength Physics and Materials Science
14 shared publications - Svetlana A. Bochkareva
Institute of Strength Physics and Materials Science of the Siberian Branch of the Russian Academy of Sciences, Tomsk, Russia
13 shared publications - Boris A. Lyukshin
Institute of Strength Physics and Materials Science of the Siberian Branch of the Russian Academy of Sciences, Tomsk, Russia
4 shared publications - Vladislav Alexenko
Laboratory of Mechanics of Polymer Composite Materials, V.E. Panin Institute of Strength Physics and Materials Science of Siberian Branch of Russian Academy of Sciences, Tomsk, 634055, Russia
4 shared publications B. A. Lyukshin
National Research Tomsk State University, Tomsk, 634050 Russia
3 shared publications- Dmitry G. Buslovich
Laboratory of Nanobioengineering, V.E. Panin Institute of Strength Physics and Materials Science of Siberian Branch of Russian Academy of Sciences, Tomsk 634055, Russia
3 shared publications
Latest Publications
- Open Access
- 26 March 2025
- Published by Gruppo Italiano Frattura in Fracture and Structural Integrity
- Vol. 19 (72) , 280-294
Improving mechanical properties of removable complete dentures for maxilla by reinforcing their bases with perforated PEEK framework
The paper presents the results of computer simulation of a hybrid removable complete dentures (RCD) of a maxilla and analysis of its stress–strain states (SSSs) under typical operational loads. For improving their strength and stiffness, it was proposed to reinforce a base made of polymethylmethacrylate (PMMA) with a perforated framework (technological holes for enhancing adhesion) made of polyetheretherketone (PEEK). In total, the SSS for 10 different models were analyzed, simulating the presence or absence of a reinforcing framework as well as its perforation, location in the base, adhesion between the components, and the deformation of the alveolar ridge. The key difference of the conducted computer simulation was the application of a virtual support of the RCD. Its deformation imitated changes in the alveolar ridge height, as well as the presence of more rigid areas corresponding directly to both alveolar ridge and a torus. The SSSs for the FE-models were calculated by the finite element method using the ‘ABAQUS’ software package. The effect of the PEEK framework position on the mechanical properties of the RСD was assessed. It was shown that the main reason for the base’s failure was its bending under the applied loads. However, the load-bearing capacity of the RСD could be increased by 20–40% by embedding of the PEEK framework as an additional layer of the base dome. The effect of variation in the base support conditions, simulating the degradation of the alveolar ridge caused by the bone tissue resorption, was analyzed. It was found that the load-bearing capacity of the RСD could vary within 10% in such cases. The perforation in the PEEK framework did not reduce significantly the mechanical properties of the RСD, but its adhesion to the PMMA base exerted a decisive effect on the operational performance.
- 26 March 2025
- Published by Gruppo Italiano Frattura in Fracture and Structural Integrity
- Vol. 19 (72) , 280-294
Open AccessImproving mechanical properties of removable complete dentures for maxilla by reinforcing their bases with perforated PEEK framework
The paper presents the results of computer simulation of a hybrid removable complete dentures (RCD) of a maxilla and analysis of its stress–strain states (SSSs) under typical operational loads. For improving their strength and stiffness, it was proposed to reinforce a base made of polymethylmethacrylate (PMMA) with a perforated framework (technological holes for enhancing adhesion) made of polyetheretherketone (PEEK). In total, the SSS for 10 different models were analyzed, simulating the presence or absence of a reinforcing framework as well as its perforation, location in the base, adhesion between the components, and the deformation of the alveolar ridge. The key difference of the conducted computer simulation was the application of a virtual support of the RCD. Its deformation imitated changes in the alveolar ridge height, as well as the presence of more rigid areas corresponding directly to both alveolar ridge and a torus. The SSSs for the FE-models were calculated by the finite element method using the ‘ABAQUS’ software package. The effect of the PEEK framework position on the mechanical properties of the RСD was assessed. It was shown that the main reason for the base’s failure was its bending under the applied loads. However, the load-bearing capacity of the RСD could be increased by 20–40% by embedding of the PEEK framework as an additional layer of the base dome. The effect of variation in the base support conditions, simulating the degradation of the alveolar ridge caused by the bone tissue resorption, was analyzed. It was found that the load-bearing capacity of the RСD could vary within 10% in such cases. The perforation in the PEEK framework did not reduce significantly the mechanical properties of the RСD, but its adhesion to the PMMA base exerted a decisive effect on the operational performance.
- Open Access
- 26 March 2025
- Published by Gruppo Italiano Frattura in Fracture and Structural Integrity
- Vol. 19 (72) , 280-294
Improving mechanical properties of removable complete dentures for maxilla by reinforcing their bases with perforated PEEK framework
The paper presents the results of computer simulation of a hybrid removable complete dentures (RCD) of a maxilla and analysis of its stress–strain states (SSSs) under typical operational loads. For improving their strength and stiffness, it was proposed to reinforce a base made of polymethylmethacrylate (PMMA) with a perforated framework (technological holes for enhancing adhesion) made of polyetheretherketone (PEEK). In total, the SSS for 10 different models were analyzed, simulating the presence or absence of a reinforcing framework as well as its perforation, location in the base, adhesion between the components, and the deformation of the alveolar ridge. The key difference of the conducted computer simulation was the application of a virtual support of the RCD. Its deformation imitated changes in the alveolar ridge height, as well as the presence of more rigid areas corresponding directly to both alveolar ridge and a torus. The SSSs for the FE-models were calculated by the finite element method using the ‘ABAQUS’ software package. The effect of the PEEK framework position on the mechanical properties of the RСD was assessed. It was shown that the main reason for the base’s failure was its bending under the applied loads. However, the load-bearing capacity of the RСD could be increased by 20–40% by embedding of the PEEK framework as an additional layer of the base dome. The effect of variation in the base support conditions, simulating the degradation of the alveolar ridge caused by the bone tissue resorption, was analyzed. It was found that the load-bearing capacity of the RСD could vary within 10% in such cases. The perforation in the PEEK framework did not reduce significantly the mechanical properties of the RСD, but its adhesion to the PMMA base exerted a decisive effect on the operational performance.
- 26 March 2025
- Published by Gruppo Italiano Frattura in Fracture and Structural Integrity
- Vol. 19 (72) , 280-294
Open AccessImproving mechanical properties of removable complete dentures for maxilla by reinforcing their bases with perforated PEEK framework
The paper presents the results of computer simulation of a hybrid removable complete dentures (RCD) of a maxilla and analysis of its stress–strain states (SSSs) under typical operational loads. For improving their strength and stiffness, it was proposed to reinforce a base made of polymethylmethacrylate (PMMA) with a perforated framework (technological holes for enhancing adhesion) made of polyetheretherketone (PEEK). In total, the SSS for 10 different models were analyzed, simulating the presence or absence of a reinforcing framework as well as its perforation, location in the base, adhesion between the components, and the deformation of the alveolar ridge. The key difference of the conducted computer simulation was the application of a virtual support of the RCD. Its deformation imitated changes in the alveolar ridge height, as well as the presence of more rigid areas corresponding directly to both alveolar ridge and a torus. The SSSs for the FE-models were calculated by the finite element method using the ‘ABAQUS’ software package. The effect of the PEEK framework position on the mechanical properties of the RСD was assessed. It was shown that the main reason for the base’s failure was its bending under the applied loads. However, the load-bearing capacity of the RСD could be increased by 20–40% by embedding of the PEEK framework as an additional layer of the base dome. The effect of variation in the base support conditions, simulating the degradation of the alveolar ridge caused by the bone tissue resorption, was analyzed. It was found that the load-bearing capacity of the RСD could vary within 10% in such cases. The perforation in the PEEK framework did not reduce significantly the mechanical properties of the RСD, but its adhesion to the PMMA base exerted a decisive effect on the operational performance.
- Open Access
- 15 March 2024
- Published by Gruppo Italiano Frattura in Fracture and Structural Integrity
- Vol. 18 (68) , 390-409
Ultrasonic welding of lap joints of PEI plates with PEI/CF-fabric prepregs
In this study, ultrasonic welding (USW) of lap joints of polyetherimide (PEI) plates (adherends) with carbon fiber (CF) prepregs impregnated with PEI was investigated. No energy director (ED) was used, so binder contents were varied in the prepregs to compensate for the lack of the polymer in the fusion zone. In addition, the effect of the USW parameters on the structure and the mechanical properties of the lap-joints were analyzed. The most homogeneous macrostructure, the maintained structural integrity of both the CF-fabric in the prepregs and the lap-joined PEI adherends, as well as the maximum strength properties (tensile strength) were revealed for the USW joints with the minimum polymer content in the prepreg. In this case, rising the USW time from 400 up to 800 ms radically changed the macrostructure of the fusion zone, while the strength properties did not vary significantly (shear stresses were 42–48 MPa). Computer simulation of the influence of the PEI/CF-fabric ratios in the prepregs on the deformation response of the USW joints showed that the prepreg thicknesses and, accordingly, the PEI/CF ratios did not exert a noticeable effect on the strain–stress (tensile) diagrams, while the determining factor was the adhesion level.
- 15 March 2024
- Published by Gruppo Italiano Frattura in Fracture and Structural Integrity
- Vol. 18 (68) , 390-409
Open AccessUltrasonic welding of lap joints of PEI plates with PEI/CF-fabric prepregs
In this study, ultrasonic welding (USW) of lap joints of polyetherimide (PEI) plates (adherends) with carbon fiber (CF) prepregs impregnated with PEI was investigated. No energy director (ED) was used, so binder contents were varied in the prepregs to compensate for the lack of the polymer in the fusion zone. In addition, the effect of the USW parameters on the structure and the mechanical properties of the lap-joints were analyzed. The most homogeneous macrostructure, the maintained structural integrity of both the CF-fabric in the prepregs and the lap-joined PEI adherends, as well as the maximum strength properties (tensile strength) were revealed for the USW joints with the minimum polymer content in the prepreg. In this case, rising the USW time from 400 up to 800 ms radically changed the macrostructure of the fusion zone, while the strength properties did not vary significantly (shear stresses were 42–48 MPa). Computer simulation of the influence of the PEI/CF-fabric ratios in the prepregs on the deformation response of the USW joints showed that the prepreg thicknesses and, accordingly, the PEI/CF ratios did not exert a noticeable effect on the strain–stress (tensile) diagrams, while the determining factor was the adhesion level.
- Open Access
Structure and Deformation Behavior of Polyphenylene Sulfide-Based Laminates Reinforced with Carbon Fiber Tapes Activated by Cold Atmospheric Plasma
Low-temperature plasma treatment with atmospheric discharge with runaway electrons (DRE) was shown to be an efficient way to activate carbon fiber’s (CF) surface and subsequently increase its interlayer shear strength (ILSS) values. It was demonstrated that an acceptable ILSS level was achieved after a DRE plasma treatment duration of 15 min. The treatment of CFs resulted in their surface roughness being increased and their functional groups grafting. The XPS data showed a change in the chemical composition and the formation of reactive oxygen-containing groups. SEM examinations of the PPS/CF laminates clearly demonstrated a difference in adhesive interaction at the PPS/CF interface. After the DRE plasma treatment, CFs were better wetted with the polymer, and the samples cohesively fractured predominantly through the matrix, but not along the PPS/CF interface, as was observed for the sample reinforced with the untreated CFs. The computer simulation results showed that raising the adhesive strength enhanced the ILSS values, but reduced resistance to transverse cracking under the loading pin. In general, higher flexural strength of the PPS/CF laminates was achieved with a greater interlayer adhesion level, which was consistent with the obtained experimental data.
Open AccessStructure and Deformation Behavior of Polyphenylene Sulfide-Based Laminates Reinforced with Carbon Fiber Tapes Activated by Cold Atmospheric Plasma
Low-temperature plasma treatment with atmospheric discharge with runaway electrons (DRE) was shown to be an efficient way to activate carbon fiber’s (CF) surface and subsequently increase its interlayer shear strength (ILSS) values. It was demonstrated that an acceptable ILSS level was achieved after a DRE plasma treatment duration of 15 min. The treatment of CFs resulted in their surface roughness being increased and their functional groups grafting. The XPS data showed a change in the chemical composition and the formation of reactive oxygen-containing groups. SEM examinations of the PPS/CF laminates clearly demonstrated a difference in adhesive interaction at the PPS/CF interface. After the DRE plasma treatment, CFs were better wetted with the polymer, and the samples cohesively fractured predominantly through the matrix, but not along the PPS/CF interface, as was observed for the sample reinforced with the untreated CFs. The computer simulation results showed that raising the adhesive strength enhanced the ILSS values, but reduced resistance to transverse cracking under the loading pin. In general, higher flexural strength of the PPS/CF laminates was achieved with a greater interlayer adhesion level, which was consistent with the obtained experimental data.
- 25 March 2023
- Published by Springer Nature in Russian Physics Journal
- Vol. 65 (12) , 2193-2200
Influence of Plasma Modification of Basalt Fibers on the Physical and Mechanical Characteristics of Peek-Based Laminates
- 25 March 2023
- Published by Springer Nature in Russian Physics Journal
- Vol. 65 (12) , 2193-2200
Influence of Plasma Modification of Basalt Fibers on the Physical and Mechanical Characteristics of Peek-Based Laminates
- Open Access
Surface Modification of Carbon Fibers by Low-Temperature Plasma with Runaway Electrons for Manufacturing PEEK-Based Laminates
(1) Background: The paper addresses the effect of carbon fibers (CFs) treatment by low-temperature plasma with runaway electrons on the deformation behavior of the polyetheretherketone (PEEK)-layered composites. (2) Methods: The effect of the interlayer adhesion on the mechanical response of the composites was assessed through the tensile and three-point bending tests. In addition, computer simulations of the three-point bending were carried out with the use of the finite element analysis (FEM) with varying conditions at the “PEEK–CF layers” interface. (3) Results: DRE–plasma treatment during the optimal time of t = 15 min led to formation of a rougher surface and partial desizing of a finishing agent. The shear strength of the layered composites increased by 54%, while the tensile strength and the flexural modulus (at three-point bending) increased by 16% (up to 893 MPa) and by 10% (up to 93 GPa), respectively. (4) Conclusions: The results of the numerical experiments showed that the increase in the stiffness, on the one hand, gave rise to enlarging the flexural modulus; on the other hand, a nonlinear decrease in the strength may occur. For this reason, the intention to maximize the level of the interlayer stiffness can result in lowering the fracture toughness, for example, at manufacturing high-strength composites.
Open AccessSurface Modification of Carbon Fibers by Low-Temperature Plasma with Runaway Electrons for Manufacturing PEEK-Based Laminates
(1) Background: The paper addresses the effect of carbon fibers (CFs) treatment by low-temperature plasma with runaway electrons on the deformation behavior of the polyetheretherketone (PEEK)-layered composites. (2) Methods: The effect of the interlayer adhesion on the mechanical response of the composites was assessed through the tensile and three-point bending tests. In addition, computer simulations of the three-point bending were carried out with the use of the finite element analysis (FEM) with varying conditions at the “PEEK–CF layers” interface. (3) Results: DRE–plasma treatment during the optimal time of t = 15 min led to formation of a rougher surface and partial desizing of a finishing agent. The shear strength of the layered composites increased by 54%, while the tensile strength and the flexural modulus (at three-point bending) increased by 16% (up to 893 MPa) and by 10% (up to 93 GPa), respectively. (4) Conclusions: The results of the numerical experiments showed that the increase in the stiffness, on the one hand, gave rise to enlarging the flexural modulus; on the other hand, a nonlinear decrease in the strength may occur. For this reason, the intention to maximize the level of the interlayer stiffness can result in lowering the fracture toughness, for example, at manufacturing high-strength composites.
- Open Access
- 29 June 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (13) , 4511
Design of Wear-Resistant UHMWPE-Based Composites Loaded with Wollastonite Microfibers Treated with Various Silane Coupling Agents
The tribomechanical properties of the wear-resistant ultrahigh molecular weight polyethylene (UHMWPE)-based composites loaded with wollastonite microfibres silanized with various coupling agents (“KH-550”, “Penta-1006”, and “OTS”) were investigated. It was demonstrated that the mechanical properties of UHMWPE-based composites filled with various amounts of wollastonite (7–23 wt. %) increased by 1.3 times (yield strength) and by 1.8 times (elastic modulus), while the wollastonite silanization further improved yield strength by 9% in some cases. It was demonstrated that the composite loaded with 23 wt. % wollastonite silanized with the “KH-550” coupling agent possessed the maximum wear resistance under “moderate” conditions of tribological loading. Under “severe” conditions, the composites containing 23 wt. % wollastonite silanized with the less efficient “OTS” and “Penta-1006” agents showed the greatest wear resistance during dry sliding friction. Wear resistance significantly depended on filler weight fraction and the load–speed mode of the tribological tests. Based on the obtained experimental data on the mechanical (including impact toughness) and tribological properties of the UHMWPE-based composites loaded with wollastonite, the optimal compositions (the filler content and the type of the coupling agent) for two load–speed modes were designed using the developed computer algorithm. The composites provided the predefined high tribomechanical properties for operation in the metal-polymer friction units compared to neat polymer.
- 29 June 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (13) , 4511
Open AccessDesign of Wear-Resistant UHMWPE-Based Composites Loaded with Wollastonite Microfibers Treated with Various Silane Coupling Agents
The tribomechanical properties of the wear-resistant ultrahigh molecular weight polyethylene (UHMWPE)-based composites loaded with wollastonite microfibres silanized with various coupling agents (“KH-550”, “Penta-1006”, and “OTS”) were investigated. It was demonstrated that the mechanical properties of UHMWPE-based composites filled with various amounts of wollastonite (7–23 wt. %) increased by 1.3 times (yield strength) and by 1.8 times (elastic modulus), while the wollastonite silanization further improved yield strength by 9% in some cases. It was demonstrated that the composite loaded with 23 wt. % wollastonite silanized with the “KH-550” coupling agent possessed the maximum wear resistance under “moderate” conditions of tribological loading. Under “severe” conditions, the composites containing 23 wt. % wollastonite silanized with the less efficient “OTS” and “Penta-1006” agents showed the greatest wear resistance during dry sliding friction. Wear resistance significantly depended on filler weight fraction and the load–speed mode of the tribological tests. Based on the obtained experimental data on the mechanical (including impact toughness) and tribological properties of the UHMWPE-based composites loaded with wollastonite, the optimal compositions (the filler content and the type of the coupling agent) for two load–speed modes were designed using the developed computer algorithm. The composites provided the predefined high tribomechanical properties for operation in the metal-polymer friction units compared to neat polymer.
- Open Access
Effect of Adhesion on Mechanical and Tribological Properties of Glass Fiber Composites, Based on Ultra-High Molecular Weight Polyethylene Powders with Various Initial Particle Sizes
The aim of this study was to assess the effect of adhesion between the non-polar, ultra-high molecular weight polyethylene (UHMWPE) matrix and the glass fiber fillers of various lengths treated with the commercially available “KH-550” agent, on the mechanical and tribological properties of the UHMWPE-based composites. The motivation was to find the optimal compositions of the polymer composite, for the compression sintering manufacturing of lining plates for the protection of marine venders and construction vehicles, as well as transport equipment. It was shown that the initial powder size at equal molecular weight determined the distribution patterns of the glass fibers in the matrix, and, as a consequence, the mechanical and tribological properties of the composites. Based on the obtained experimental data and the results of the calculation by a developed computer algorithm, control parameters were determined to give practical recommendations (polymer powder size and glass fiber length), for the production of the UHMWPE-composites having specified mechanical and tribological characteristics. The “GUR4022 + 10% LGF” composite, loaded with the chopped 3 mm glass fibers treated with the “KH-550”, was recommended for severe operating conditions (high loads, including impact and abrasive wear). For mild operating conditions (including cases when the silane coupling agent could not be used), the “GUR2122 + 10% MGF” and “GUR2122 + 10% LGF” composites, based on the fine UHMWPE powder, were recommended. However, the cost and technological efficiency of the filler (flowability, dispersibility) and polymer powder processing should be taken into account, in addition to the specified mechanical and tribological properties.
Open AccessEffect of Adhesion on Mechanical and Tribological Properties of Glass Fiber Composites, Based on Ultra-High Molecular Weight Polyethylene Powders with Various Initial Particle Sizes
The aim of this study was to assess the effect of adhesion between the non-polar, ultra-high molecular weight polyethylene (UHMWPE) matrix and the glass fiber fillers of various lengths treated with the commercially available “KH-550” agent, on the mechanical and tribological properties of the UHMWPE-based composites. The motivation was to find the optimal compositions of the polymer composite, for the compression sintering manufacturing of lining plates for the protection of marine venders and construction vehicles, as well as transport equipment. It was shown that the initial powder size at equal molecular weight determined the distribution patterns of the glass fibers in the matrix, and, as a consequence, the mechanical and tribological properties of the composites. Based on the obtained experimental data and the results of the calculation by a developed computer algorithm, control parameters were determined to give practical recommendations (polymer powder size and glass fiber length), for the production of the UHMWPE-composites having specified mechanical and tribological characteristics. The “GUR4022 + 10% LGF” composite, loaded with the chopped 3 mm glass fibers treated with the “KH-550”, was recommended for severe operating conditions (high loads, including impact and abrasive wear). For mild operating conditions (including cases when the silane coupling agent could not be used), the “GUR2122 + 10% MGF” and “GUR2122 + 10% LGF” composites, based on the fine UHMWPE powder, were recommended. However, the cost and technological efficiency of the filler (flowability, dispersibility) and polymer powder processing should be taken into account, in addition to the specified mechanical and tribological properties.
- Open Access
Material Design Methodology for Optimized Wear-Resistant Thermoplastic–Matrix Composites Based on Polyetheretherketone and Polyphenylene Sulfide
The main goal of this paper is to design and justify optimized compositions of thermoplastic–matrix wear-resistant composites based on polyetheretherketone (PEEK) and polyphenylene sulfide (PPS). Their mechanical and tribological properties have been specified in the form of bilateral and unilateral limits. For this purpose, a material design methodology has been developed. It has enabled to determine the optimal degrees of filling of the PEEK- and PPS-based composites with carbon microfibers and polytetrafluoroethylene particles. According to the results of tribological tests, the PEEK-based composites have been less damaged on the metal counterpart than the PPS-based samples having the same degree of filling. Most likely, this was due to more uniform permolecular structure and greater elasticity of the matrix. The described methodology is versatile and can be used to design various composites. Its implementation does not impose any limits on the specified properties of the material matrix or the reinforcing inclusions. The initial data on the operational characteristics can be obtained experimentally or numerically. The methodology enables to design the high-strength wear-resistant composites which are able to efficiently operate both in metal–polymer and ceramic–polymer friction units.
Open AccessMaterial Design Methodology for Optimized Wear-Resistant Thermoplastic–Matrix Composites Based on Polyetheretherketone and Polyphenylene Sulfide
The main goal of this paper is to design and justify optimized compositions of thermoplastic–matrix wear-resistant composites based on polyetheretherketone (PEEK) and polyphenylene sulfide (PPS). Their mechanical and tribological properties have been specified in the form of bilateral and unilateral limits. For this purpose, a material design methodology has been developed. It has enabled to determine the optimal degrees of filling of the PEEK- and PPS-based composites with carbon microfibers and polytetrafluoroethylene particles. According to the results of tribological tests, the PEEK-based composites have been less damaged on the metal counterpart than the PPS-based samples having the same degree of filling. Most likely, this was due to more uniform permolecular structure and greater elasticity of the matrix. The described methodology is versatile and can be used to design various composites. Its implementation does not impose any limits on the specified properties of the material matrix or the reinforcing inclusions. The initial data on the operational characteristics can be obtained experimentally or numerically. The methodology enables to design the high-strength wear-resistant composites which are able to efficiently operate both in metal–polymer and ceramic–polymer friction units.
- Open Access
- 19 November 2019
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2167 (1) , 020121
Content optimization of polyphenylene sulfide composites filled with carbon fibers of different size
The chemical content of polyphenylene sulfide (PPS) based composite with specified physical–mechanical properties is determined in the study with the use of experimental data on the dependence of effective properties (volumetric wear, elastic modulus, elongation at break, etc.) versus the values of control parameters. The latter are degree of filling with (i) Short Carbon Fibers (SCF) of ∼70 µm long and (ii) Chopped Carbon Fibers (CCF) ∼2 mm long. After the required number of experimental reference points has been determined the technique for data supplementation up to a regular numerical array with the use of linear interpolation is employed. The obtained dependences of the effective properties versus the control parameter values are constructed in the form of surfaces and corresponding isolines. At the contour plots, a region with the required effective properties is then highlighted. Since the regions overlap each other, their intersection determines the allowable control parameters range that impart the required values to the effective properties. The possibility to design filled polymer materials with a complex of predefined strain-strength and tribological properties is demonstrated. The experimental results are used to gain the reference points in contrast to the previously used approach when a set of computational experiment data were employed. On the one hand, the combination of a full-scale laboratory and computational experiments makes the process of modeling and design materials more evident, clear and reasonable from a physical point of view. On the other hand, it allows to interpret the results as more reliable, as well as less time and material consuming.
- 19 November 2019
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2167 (1) , 020121
Open AccessContent optimization of polyphenylene sulfide composites filled with carbon fibers of different size
The chemical content of polyphenylene sulfide (PPS) based composite with specified physical–mechanical properties is determined in the study with the use of experimental data on the dependence of effective properties (volumetric wear, elastic modulus, elongation at break, etc.) versus the values of control parameters. The latter are degree of filling with (i) Short Carbon Fibers (SCF) of ∼70 µm long and (ii) Chopped Carbon Fibers (CCF) ∼2 mm long. After the required number of experimental reference points has been determined the technique for data supplementation up to a regular numerical array with the use of linear interpolation is employed. The obtained dependences of the effective properties versus the control parameter values are constructed in the form of surfaces and corresponding isolines. At the contour plots, a region with the required effective properties is then highlighted. Since the regions overlap each other, their intersection determines the allowable control parameters range that impart the required values to the effective properties. The possibility to design filled polymer materials with a complex of predefined strain-strength and tribological properties is demonstrated. The experimental results are used to gain the reference points in contrast to the previously used approach when a set of computational experiment data were employed. On the one hand, the combination of a full-scale laboratory and computational experiments makes the process of modeling and design materials more evident, clear and reasonable from a physical point of view. On the other hand, it allows to interpret the results as more reliable, as well as less time and material consuming.