Serkan Biyik
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Serkan Biyik has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
Murat Aydin
Department of Mechanical Engineering, Faculty of Engineering, Karadeniz Technical University, Trabzon, Turkey
2 shared publicationsFazli Arslan
Avrasya University
1 shared publication- Onur Güler
Karadeniz Technical University
1 shared publication - Temel Varol
Department of Metallurgical and Materials Engineering, Karadeniz Technical University, Trabzon, Türkiye
1 shared publication Ümit Alver
1 shared publication
Latest Publications
- Top Cited PapersOpen Access
- 16 February 2026
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 55 (4) , 3850-3867
Effect of TiO2 Content on the Arc-Erosion Resistance of Ag/SnO2 Electrical Contact Materials Prepared via Mechanical Alloying-Assisted Powder Metallurgy
In this study, the arc-erosion performances of AgSnO 2 -based electrical contact materials containing different amounts of titanium dioxide (TiO 2 ) were investigated using the mechanical alloying-assisted powder metallurgy method. For this purpose, composite powder synthesis was carried out through grinding experiments using a planetary ball mill, and the produced composite powders were subjected to molding and vacuum sintering processes. Subsequently, electrical wear tests were carried out under inductive loads to investigate the arc-erosion performance of composites. Scanning electron microscopy (SEM), energy dispersive x-ray spectroscopy (EDS), and laser diffractometry techniques were used to characterize powders, green compacts, composites and arc-affected surfaces. The results showed that the smallest composite powder size (1.186 µm) was obtained from samples containing 7% by weight of TiO 2 . Furthermore, it was determined that the green compacts containing 1% TiO 2 had the lowest porosity ratio (1.21%). In addition, the hardness values were observed to gradually increase from 82 HV to 112 HV with increasing TiO 2 content. It was also observed that the use of 5% TiO 2 improved the interfacial wettability between the matrix and reinforcement, thereby increasing the viscosity of the abraded material and reducing particle spatter. One of the key findings of the study is that, under test conditions of 220 V, 50 Hz, and 20 A, the addition of 5% TiO 2 reduced total mass losses by 46.78%.
- 16 February 2026
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 55 (4) , 3850-3867
Top Cited PapersOpen AccessEffect of TiO2 Content on the Arc-Erosion Resistance of Ag/SnO2 Electrical Contact Materials Prepared via Mechanical Alloying-Assisted Powder Metallurgy
In this study, the arc-erosion performances of AgSnO 2 -based electrical contact materials containing different amounts of titanium dioxide (TiO 2 ) were investigated using the mechanical alloying-assisted powder metallurgy method. For this purpose, composite powder synthesis was carried out through grinding experiments using a planetary ball mill, and the produced composite powders were subjected to molding and vacuum sintering processes. Subsequently, electrical wear tests were carried out under inductive loads to investigate the arc-erosion performance of composites. Scanning electron microscopy (SEM), energy dispersive x-ray spectroscopy (EDS), and laser diffractometry techniques were used to characterize powders, green compacts, composites and arc-affected surfaces. The results showed that the smallest composite powder size (1.186 µm) was obtained from samples containing 7% by weight of TiO 2 . Furthermore, it was determined that the green compacts containing 1% TiO 2 had the lowest porosity ratio (1.21%). In addition, the hardness values were observed to gradually increase from 82 HV to 112 HV with increasing TiO 2 content. It was also observed that the use of 5% TiO 2 improved the interfacial wettability between the matrix and reinforcement, thereby increasing the viscosity of the abraded material and reducing particle spatter. One of the key findings of the study is that, under test conditions of 220 V, 50 Hz, and 20 A, the addition of 5% TiO 2 reduced total mass losses by 46.78%.
- 18 September 2024
- Published by Uludag University Journal of the Faculty of Engineering in Uludağ University Journal of The Faculty of Engineering
- p. 713-724
TUNGSTEN KARBÜR TAKVİYELİ BAKIR ESASLI KOMPOZİT TOZUNUN MEKANİK ALAŞIMLAMA YÖNTEMİYLE SENTEZİNE İŞLEM KONTROL KATKILARININ ETKİSİ
Tungsten karbür (WC) parçacık-takviyeli bakır (Cu) esaslı kompozitler geleneksel malzemelere göre özellikle aşınma dayanımı, sertlik, yüksek sıcaklık dayanımı ve ark oluşumu ile gerçekleşen malzeme transferi üzerindeki olumlu etkileri sayesinde elektrik kontak malzemesi üretiminde kullanılmaktadır. CuWC kompozit tozu; işlem kontrol katkısı cinsi ve miktarı, öğütme hızı, bilye-toz-ağırlık oranı ve öğütme süresi gibi birçok işlem parametresinin optimize edilmesi sayesinde mekanik alaşımlama (MA) yöntemi ile üretilebilir. Bu yüzden çalışmada işlem kontrol katkısının, CuWC kompozit toz sentezine etkisi araştırılmıştır. Bu amaçla Cu ve WC tozlarından oluşan karışıma katı işlem kontrol katkısı olarak stearik asit, polietilen glikol ve çinko stearat ayrı ayrı ilave edilerek oluşturulan üç farklı karışım bilyeli öğütücüde öğütülmüştür. Polietilen glikol kullanımında öğütme verimi en düşük seviyelerde iken çinko stearatın 16 saate kadar belirgin etkisi öne çıkmaktadır. Ortalama toz boyutu değerleri ve SEM görüntülerinin karşılaştırılmasından 25 saatlik öğütme sonucunda en uygun işlem kontrol katkısının stearik asit olduğu tespit edilmiştir.
- 18 September 2024
- Published by Uludag University Journal of the Faculty of Engineering in Uludağ University Journal of The Faculty of Engineering
- p. 713-724
TUNGSTEN KARBÜR TAKVİYELİ BAKIR ESASLI KOMPOZİT TOZUNUN MEKANİK ALAŞIMLAMA YÖNTEMİYLE SENTEZİNE İŞLEM KONTROL KATKILARININ ETKİSİ
Tungsten karbür (WC) parçacık-takviyeli bakır (Cu) esaslı kompozitler geleneksel malzemelere göre özellikle aşınma dayanımı, sertlik, yüksek sıcaklık dayanımı ve ark oluşumu ile gerçekleşen malzeme transferi üzerindeki olumlu etkileri sayesinde elektrik kontak malzemesi üretiminde kullanılmaktadır. CuWC kompozit tozu; işlem kontrol katkısı cinsi ve miktarı, öğütme hızı, bilye-toz-ağırlık oranı ve öğütme süresi gibi birçok işlem parametresinin optimize edilmesi sayesinde mekanik alaşımlama (MA) yöntemi ile üretilebilir. Bu yüzden çalışmada işlem kontrol katkısının, CuWC kompozit toz sentezine etkisi araştırılmıştır. Bu amaçla Cu ve WC tozlarından oluşan karışıma katı işlem kontrol katkısı olarak stearik asit, polietilen glikol ve çinko stearat ayrı ayrı ilave edilerek oluşturulan üç farklı karışım bilyeli öğütücüde öğütülmüştür. Polietilen glikol kullanımında öğütme verimi en düşük seviyelerde iken çinko stearatın 16 saate kadar belirgin etkisi öne çıkmaktadır. Ortalama toz boyutu değerleri ve SEM görüntülerinin karşılaştırılmasından 25 saatlik öğütme sonucunda en uygun işlem kontrol katkısının stearik asit olduğu tespit edilmiştir.
- Open Access
- 16 July 2024
- Published by Iskender AKKURT in International Journal of Computational and Experimental Science and Engineering
- Vol. 10 (3)
Influence of Polyethylene Glycol and Methanol Additions on the Mechanical Alloying Behavior of Cu-4B4C Composite Powder
This study investigated the effect of different process control agent (PCA) usage on mechanical alloying behavior of boron carbide (B4C) reinforced copper (Cu) based composite powder. For this purpose, elemental Cu and B4C powders were weighed and powder specimens were prepared with respect to appropriate mass ratios (96% Cu and 4% B4C). Two different PCA additives, namely polyethylene glycol (PEG) and methanol, were also used to prepare powder samples. The amount of PCA was kept constant at 5wt.% for both specimen. These prepared powder samples were then milled using a planetary type ball-mill. After specified milling periods, milling runs were interrupted and powder samples were extracted from the milling vials for further powder characterization including powder morphology using scanning electron microscopy (SEM) and average particle size (APS) via laser diffraction analysis (Mastersizer). Accordingly, after the completion of milling runs, namely 15 hours of ball-milling, methanol addition was found much more effective at reducing particle sizes than PEG. Final APS values for powder specimens having PEG and methanol as PCAs were determined to be 8.237 and 4.101 microns, respectively.
- 16 July 2024
- Published by Iskender AKKURT in International Journal of Computational and Experimental Science and Engineering
- Vol. 10 (3)
Open AccessInfluence of Polyethylene Glycol and Methanol Additions on the Mechanical Alloying Behavior of Cu-4B4C Composite Powder
This study investigated the effect of different process control agent (PCA) usage on mechanical alloying behavior of boron carbide (B4C) reinforced copper (Cu) based composite powder. For this purpose, elemental Cu and B4C powders were weighed and powder specimens were prepared with respect to appropriate mass ratios (96% Cu and 4% B4C). Two different PCA additives, namely polyethylene glycol (PEG) and methanol, were also used to prepare powder samples. The amount of PCA was kept constant at 5wt.% for both specimen. These prepared powder samples were then milled using a planetary type ball-mill. After specified milling periods, milling runs were interrupted and powder samples were extracted from the milling vials for further powder characterization including powder morphology using scanning electron microscopy (SEM) and average particle size (APS) via laser diffraction analysis (Mastersizer). Accordingly, after the completion of milling runs, namely 15 hours of ball-milling, methanol addition was found much more effective at reducing particle sizes than PEG. Final APS values for powder specimens having PEG and methanol as PCAs were determined to be 8.237 and 4.101 microns, respectively.
- Top Cited Papers
- 1 August 2021
- Published by Elsevier in Advanced Powder Technology
- Vol. 32 (8) , 2873-2890
The wear and arc erosion behavior of novel copper based functionally graded electrical contact materials fabricated by hot pressing assisted electroless plating
- 1 August 2021
- Published by Elsevier in Advanced Powder Technology
- Vol. 32 (8) , 2873-2890
Top Cited PapersThe wear and arc erosion behavior of novel copper based functionally graded electrical contact materials fabricated by hot pressing assisted electroless plating
- 19 September 2014
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 44 (1) , 457-466
Arc-Erosion Behavior of Boric Oxide-Reinforced Silver-Based Electrical Contact Materials Produced by Mechanical Alloying
- 19 September 2014
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 44 (1) , 457-466
Arc-Erosion Behavior of Boric Oxide-Reinforced Silver-Based Electrical Contact Materials Produced by Mechanical Alloying