NNNadia Chrisayu Natasha

Nadia Chrisayu Natasha

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Nadia Chrisayu Natasha has a total of 31 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Using the gold bullion slag from Indonesia as lithium resources with HCL leaching method

    by Nadia Natasha, Ghina Rabbani, Nofrijon Sofyan, Johny Soedarsono, Agus Prasetyo, Ahmad Maksum, Rini Riastuti, Isnanda Nuriskasari

    Primary resources are typically used in lithium extraction. Unfortunately, it impacts the dependency on the availability of primary resources to fulfill the lithium demand. Therefore, the use of secondary resources can be an alternative to using lithium resources. Gold bullion slag is an example of a potential secondary resource used as a lithium source because it contains 0.009 % lithium. This research aims at increasing lithium recovery from the gold bullion slag by studying the effects of various variables to enhance lithium recovery. Lithium extraction was carried out via HCl leaching process with concentrations of 0.5, 1.0, 1.5, and 2.0 M at 25, 40, 55, and 70 °C for 15, 30, 60, and 120 minutes. Inductively coupled plasma-optical emission spectrometry (ICP-OES) was used to examine lithium level, whereas scanning electron microscope equipped with energy dispersive X-ray spectroscopy (SEM-EDX) was used to look over the morphology. The significance of the recovery value was analyzed statistically using analysis of variance (ANOVA). The optimum variables to reach 98 % as the highest lithium recovery percentage are 1 M HCl at 55 °C for 60 minutes. ANOVA results on the acid concentration significance of the recovery value show that the p-value (0.001) is smaller than the alpha value (0.005). While, ANOVA results on the temperature and time significance of the recovery value show that the p-value (0.894) is greater than the alpha value (0.005) and p-value (0.9986) is greater than the alpha value (0.005), respectively. Analysis showed that variation in HCl concentration affected the lithium recovery value; however, temperature and time of leaching had an insignificant effect on lithium recovery. These data show that slag can be used as alternative resources to produce the lithium

  • Open Access

    MORPHOLOGY AND RESISTIVITY VALUE OF FLOURINE-DOPED TIN OXIDE (FTO) USING INDONESIAN LOCAL DIMETHYLTIN DICHLORIIDE (DTMC) PRECURSORS

    by Apti Mira Rizki, Fariza Eka Yunita, Latifa Hanum Lalasari, Januar Irawan, Tri Arini, Florentinus Firdiyono, Lia Andriyah, Nadia Chrisayu Natasha, Akhmad Herman Yuwono

    Transparent Conductive Oxide (TCO) is the main component for solar cell fabrication. One of the promising types of TCO is fluorine-doped tin oxide (FTO). The method used in depositing the conductive layer of FTO is spray pyrolysis with an ultrasonic nebulizer. The precursor is a local Indonesian product, dimethyl tin dichloride (DMTC), with doping ammonium fluoride (NH4F). The variable that used in this study were variations in deposition time (5. 10. 15. 20, and 25 minutes) with a fixed substrate temperature at 300°C and doping variations (un-doped, 2 wt.% doped and 8 wt.% doped) to see the effect of adding F doping to the precursor solution. The resistivity value with deposition time of 5. 10. 15. 20 and 25 minute (2 wt.% doped) is 0.218x100; 0.449x10-1; 1,567x10-2; 0.676x10-2 0.377x10-2 Ω.cm. For doping variations (un-doped, 2 wt% doped and 8 wt% doped) the value is 0.883x10-2; 0.377x10-2; 0.506x10-3 Ω.cm. There is a decreasing trend in the resistivity values obtained along with the increase in deposition time and the addition of doping to obtain better conductive properties. The grain size will increase with increasing deposition time and the addition of doping. The optimum resistivity value obtained in this study was 0.377x10-2 Ω.cm, obtained at the deposition time of 25 minutes with 2 wt.% doping.

  • Open Access

    Investigation of surfactant effect during synthesis of magnesium oxide nanoparticles from bittern using ultrasonic destruction process

    by Fariza Eka Yunita, Eko Sulistiyono, Nadia Chrisayu Natasha, Ahmad Rizky Rhamdani, Florentinus Firdiyono, Latifa Hanum Lalasari, Tri Arini, Enggar Setya Widyaningrum, Erlina Yustanti

    Magnesium oxide (MgO) nanoparticles have been widely used in a variety of applications because of their good surface reactivity. Magnesium oxide from bittern has a larger surface area compared to magnesium oxide from calcined magnesite and magnesium ions precipitation from bittern using sodium hydroxide has higher purity than using calcium hydroxide or ammonium hydroxide. In this research, sodium hydroxide was added to a bittern solution obtaining magnesium hydroxide precipitate, followed by the calcination process to produce magnesium oxide. Nano magnesium oxide was synthesized by the ultrasonic destruction process using ethanol and 2-propanol as media. In this study, sonication time and particle concentration effect on the ultrasonic destruction process were investigated. During the process, the sonication time was varied between 8, 16, 32, 64, and 128 minutes while the magnesium oxide concentration was varied between 1 %, 2 %, and 3 %. Increasing sonication time and particle concentration will decrease the particle size. The previous study shows that particles with very small sizes tend to have an agglomeration effect. The aim of this work is to optimize nano magnesium oxide production from bittern. Surfactant addition was also studied to prevent agglomeration between particles. Four types of surfactant namely anionic (sodium lauryl sulfate), cationic (cetyl tri-methyl-ammonium bromide), amphoteric (fatty acid amido alkyl betaine), and non-ionic (nonylphenol 10 ethoxylated) with a concentration of 1 % and a volume of 0.125 ml were added during the second ultrasonic destruction process. All types of surfactants have a positive effect to prevent agglomeration during the ultrasonic destruction process, with the amphoteric surfactant having the highest performance


  • Open Access

    The use of mica schist from Indonesia as raw material for lithium extraction process using sulfate roasting and acid leaching

    by Nadia Chrisayu Natasha, Latifa Hanum Lalasari, Lia Andriyah, Tri Arini, Fariza Yunita, Didied Haryono, Fani Rinanda

    Lithium minerals become a sub-economic raw material for lithium production to fulfill the lithium demand. This study is about lithium extraction from mica schist using the roasting and leaching processes. The mica schist located in Kebumen, Indonesia was used to study the phenomena during the lithium extraction process. Sodium sulfate was used as a roasting agent while 0.36 M sulfuric acid was used as a leaching agent. Solid/liquid ratio (1:5, 1:10, 1:15 and 1:20 (g/mL)) and leaching time (30, 60, 90 and 120 minutes) were used as variables in this study. The roasting process was done at 700 °С for 40 minutes while the leaching process was done at 70 °С and 350 rpm. The ratio of additive and mica schist was 1.5:1 (g/g). XRD, ICP-OES, and SEM were used to observe the formed compounds, chemical composition and morphology of the materials. HighScore Plus (HSP) was used to interpret the content of each compound in mica schist, roasted mica schist, and residue. ICP analysis confirmed that the mica schist contains 45.28 ppm of lithium. It is supported by XRD that lithium exists in mica schist as lepidolite (KLi2AlSi4O10(F,OH)2). Sulfate roasting did not affect the type of lepidolite but the lepidolite reactivity against the chemical agent. SEM analysis shows that the roasting process reduced the average particle size from 32.17 to 27.16 µm. ICP analysis of roasted mica schist shows that lithium concentration was reduced from 45.28 to 1.27 ppm. The optimum result from this study was 97.66 % extraction of lithium while solid/liquid ratio was 1:5 (g/ml) and leaching time was 30 minutes. HSP shows that lepidolite contents in initial mica schist, roasted mica schist and residue were 60.6; 24.3 and 18.7 %, respectively. Lithium concentration in the residue according to ICP analysis is 1.06 ppm.


  • Open Access

    Effect of Leaching Temperature on Lithium Recovery fromLi-Montmorillonite (Bledug Kuwu’s Mud)

    by L H Lalasari, M Rohmah, I Setiawan, N C Natasha, L Andriyah, T Arini, F Firdiyono, J Wahyuadi

    The availability of lithium resources in the world is important along with the development of electronic technology and electrical transportation, especially lithium batteries. In Indonesia, lithium is found in brine associated with hot spring, clay associated with a geothermal activity, and spodumene minerals. The Bledug Kuwu's Mud contained a Li-Montmorillonite phase with lithium content that was 0.0029%. For lithium recovery, Li-Montmorillonite was leached with distilled water on the S / L ratio was 1: 2 for 3 hours. In this experiment, the leaching temperature was varied as follows: 25 o C, 30 o C, 35 o C, and 45 o C. Experimental results showed that lithium recovery from Li-Montmorillonite was successfully carried out by water leaching at atmospheric pressure. This result was supported by XRD analysis on residues. It indicated that there was no Li-Montmorillonite phase at the residues. The highest percentage of lithium recoveries in this research obtained at leaching temperature of 25 o C was 87.2% (15.78 ppm).


  • Lithium recovery from Bledug Kuwu Mud volcano using water leaching method

    by Miftakhur Rohmah, Latifa Hanum Lalasari, Johny Wahyuadi, Nadia Chrisayu Natasha

    Bledug Kuwu of Mud Volcano was investigated by water leaching for lithium recovery in Indonesia deposit. Mud volcano can be used as an alternative resources beside minerals and brine because lithium trapped by geothermal phenomenon. Bledug Kuwu Mud is dominated by Aluminium-Silica Clays and lithium can be found in Li-Montmorillonite phase of Clays. The mud sample which treated in the experiment contains 0.0029% lithium on wet condition. Water leaching was done by adding 500 ml water into the mud to make its ratio become 1:2. The leaching was performed in mixer settler under ambient and low temperature (45 °C) for 2, 3, 4, 5 hours. Lithium, Sodium, Potassium, Calcium, and Magnesium which analyzed by Inductively Coupled Plasma, they were abundant element in the brine composition as the filtrate. As increasing temperature, the recovery percentage of lithium was decrease. Water leaching can recovered up to 80% lithium on Clays for ambient and lower temperature. X-Ray diffraction shows that Li-Montmorillonite didn't detect in the dried mud of residue for all experiment. Scanning Electron Microscope used to determine morphology modification of clays after water treatment at different temperature. Furthermore, brine can be used for brine resource on the next lithium processing.


  • Calcium extraction from brine water and seawater using oxalic acid

    by Nadia Chrisayu Natasha, Latifa Hanum Lalasari

    Calcium can be extracted not only from rocks but also from natural liquor such as seawater and brine water. In order to extract the calcium from seawater and brine water, oxalic acid was used in this research. Effect of variations of the volume of the oxalic acid at a constant concentration in seawater and brine water to produce calcium was investigated. The concentration of oxalic acid was 100 g/l and the variations of its volume were 2 ml, 4 ml, 6 ml, 8 ml, 10 ml, 20 ml, 30 ml, 40 ml, and 50 ml. The used seawater and brine water were firstly evaporated from 100 ml into 50 ml and then the oxalic acid was added into them with mixing to produce the calcium precipitates. The precipitates were analyzed by X-ray diffraction (XRD) and scanning electron microscope (SEM) and the filtrates were analyzed by inductively coupled plasma-optical emission spectrometry (ICP-OES). The SEM analysis showed that the precipitates from brine water were consisted of only calcium compound while from seawater sodium one was also found along with calcium compound. The XRD analysis showed that the calcium was present in the form of calcium oxalate for both seawater and brine water. The ICP-OES analysis of the filtrate from seawater precipitation showed that the its calcium content was decreased from 826.20 ppm to 0.04 ppm while from brine water, it decreased from 170.06 ppm to 1.96 ppm. These results showed that both seawater and brine water have the potential to be a raw material for calcium production.