Vladyslav Matviichuk
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Vladyslav Matviichuk has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
Vladimir Nesterenkov
7 shared publications- Olena M. Berdnikova
E.O. Paton Electric Welding Institute of the National Academy of Sciences of Ukraine
6 shared publications - Володимир Михайлович Нестеренков
E.O. Paton Electric Welding Institute of the National Academy of Sciences of Ukraine
6 shared publications - Sviatoslav Motrunich
E.O.Paton Electric Welding Institute
2 shared publications - A.E. Dmitrenko1 shared publication
Illia Klochkov
1 shared publication
Latest Publications
- Open Access
- 12 October 2026
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 5 (12 (143)) , 16-28
Determining structure formation patterns in vt6 titanium alloy at electron beam powder bed fusion
This study refines the process that defines the microstructure and mechanical properties of samples manufactured by additive electron-beam melting (EBM) from the titanium alloy VT6 powder of the Ti-6Al-4V system. The task addressed is to establish regularities in the VT6 alloy structuring, thereby determining the relationship between the parameters of the additive process, the αʹ-phase morphology, defectivity, and mechanical properties. The spherical titanium alloy VT6 powder with a particle size of 40–160 μm was used as the raw material. 50 samples measuring 25 × 25 mm and 7.5 mm high were studied. For an electron beam energy density of 15–40 J/mm3 in the range of scanning speeds from 500 mm/s to 12000 mm/s, technological modes were determined that ensure a smooth surface morphology of articles. It is noted that the material of the samples is characterized by a layered structure with a uniform chemical composition. The microstructure of grains in the deposited metal in all samples consists of a lamellar αʹ-phase and a small amount of β-phase. The sizes of lamellar components vary depending on the technological parameters. The microhardness level is in the range HV = 192.1…392.42 with a relatively uniform distribution of values. The following rational printing modes have been established: 500 mm/s / 40 J/mm3, 4000 mm/s / 24 J/mm3, 6000 mm/s / 18 J/mm3, and 8000 mm/s / 16 J/mm3. They enable the formation of a structural state of the metal with minimal defects, a dispersed α′-structure, and a uniform distribution of microhardness. The results demonstrate that the combination of high-quality powder material and rational printing mode provides high process reproducibility, structural stability, and suitability of the technology for manufacturing articles with predicted characteristics
- 12 October 2026
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 5 (12 (143)) , 16-28
Open AccessDetermining structure formation patterns in vt6 titanium alloy at electron beam powder bed fusion
This study refines the process that defines the microstructure and mechanical properties of samples manufactured by additive electron-beam melting (EBM) from the titanium alloy VT6 powder of the Ti-6Al-4V system. The task addressed is to establish regularities in the VT6 alloy structuring, thereby determining the relationship between the parameters of the additive process, the αʹ-phase morphology, defectivity, and mechanical properties. The spherical titanium alloy VT6 powder with a particle size of 40–160 μm was used as the raw material. 50 samples measuring 25 × 25 mm and 7.5 mm high were studied. For an electron beam energy density of 15–40 J/mm3 in the range of scanning speeds from 500 mm/s to 12000 mm/s, technological modes were determined that ensure a smooth surface morphology of articles. It is noted that the material of the samples is characterized by a layered structure with a uniform chemical composition. The microstructure of grains in the deposited metal in all samples consists of a lamellar αʹ-phase and a small amount of β-phase. The sizes of lamellar components vary depending on the technological parameters. The microhardness level is in the range HV = 192.1…392.42 with a relatively uniform distribution of values. The following rational printing modes have been established: 500 mm/s / 40 J/mm3, 4000 mm/s / 24 J/mm3, 6000 mm/s / 18 J/mm3, and 8000 mm/s / 16 J/mm3. They enable the formation of a structural state of the metal with minimal defects, a dispersed α′-structure, and a uniform distribution of microhardness. The results demonstrate that the combination of high-quality powder material and rational printing mode provides high process reproducibility, structural stability, and suitability of the technology for manufacturing articles with predicted characteristics
- Open Access
- 28 July 2026
- Published by Elsevier in SSRN Electronic Journal
Effect of Process Parameters of the Additive Electron Beam Process on the Properties of Thin-Walled Products from VT6 Alloy
The subject of investigation is the process of structure formation and mechanical properties of thin-walled products fabricated by additive electron beam melting (EBM) technology from VT6 titanium alloy (Ti–6Al–4V) powder. The alloy is widely used in industry due to its high weldability, strength, and fatigue resistance. Spherical VT6 titanium alloy powder with a particle size of 40–160 μm, produced by rotary plasma atomisation, was used as feedstock. A computer model was created in Materialise Magics software, from which 36 specimens were printed at beam travel speeds ranging from 500 to 6000 mm/s. It was established that a beam travel speed of 500 mm/s combined with an energy density of 40 J/mm³ ensures complete melting of the powder layer, stable shape formation, and controlled thermal conditions. This promotes the formation of a balanced (α+β)-microstructure with acicular α-phase morphology and α-lamella thickness of 0.5–1.5 μm. The volume fraction of α-Ti is 90±3 %, β-Ti - 10±3 %. The microhardness level of the specimens is HV0.1 = 3.5±0.7 GPa. The results demonstrate that the combination of high-quality powder feedstock and a rational printing mode ensures high process reproducibility, structural stability, and suitability of the technology for manufacturing thin-walled products.
- 28 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEffect of Process Parameters of the Additive Electron Beam Process on the Properties of Thin-Walled Products from VT6 Alloy
The subject of investigation is the process of structure formation and mechanical properties of thin-walled products fabricated by additive electron beam melting (EBM) technology from VT6 titanium alloy (Ti–6Al–4V) powder. The alloy is widely used in industry due to its high weldability, strength, and fatigue resistance. Spherical VT6 titanium alloy powder with a particle size of 40–160 μm, produced by rotary plasma atomisation, was used as feedstock. A computer model was created in Materialise Magics software, from which 36 specimens were printed at beam travel speeds ranging from 500 to 6000 mm/s. It was established that a beam travel speed of 500 mm/s combined with an energy density of 40 J/mm³ ensures complete melting of the powder layer, stable shape formation, and controlled thermal conditions. This promotes the formation of a balanced (α+β)-microstructure with acicular α-phase morphology and α-lamella thickness of 0.5–1.5 μm. The volume fraction of α-Ti is 90±3 %, β-Ti - 10±3 %. The microhardness level of the specimens is HV0.1 = 3.5±0.7 GPa. The results demonstrate that the combination of high-quality powder feedstock and a rational printing mode ensures high process reproducibility, structural stability, and suitability of the technology for manufacturing thin-walled products.
- Open Access
- 28 July 2026
- Published by Elsevier in SSRN Electronic Journal
Determining the Influence of Technological Parameters of the Electron-Beam Surfacing Process on Quality Indicators
This paper reports the technology and equipment designed for manufacturing parts and components with predefined properties by 3D printing methods. Underlying the technology is the use of a beam of high-power electrons to smelt metal powder in a vacuum chamber with the formation of successive layers that repeat the contours of the digital model of the article. The object of research is the process of surfacing articles from the Ti6Al4Vtitanium alloy powder. The purpose is to determine the optimal surfacing modes based on identifying the effect of process parameters on the quality indicators of articles. The result of the study is the analyzed influence of technological parameters on the properties of articles. The optimum energy density of the beam of 44.5 J/mm3has been determined. Based on the research results, 25 experimental samples were printed. Three beam speed modes were used: 270, 540, and 780 mm/s. For each mode, the dynamic focusing current varied from −1.2 to 1.27 A in increments of about 0.3 A. The articles were carefully examined. A method of raster electron microscopy was used to study the morphology of the samples' surfaces in several zones, namely in the central zone and along the contour; the roughness parameters of the surface micro relief, as well as the presence of defects (pores, non-melting, micro irregularities, inclusions), were established. It has been found that the articles are characterized mainly by a homogeneous micro relief of the profile. The structure of surfaces, formed in different zones depending on technological modes, differs in its morphology. Surfacing modes have been established that have the practical application: beam speed, 780 mm/s; power, 675 W; dynamic focus current, from –1.2 to 0 A. This provides for the minimal parameters of the surface micro relief and the absence of defects such as shrinkage pores, non-melting, as well as a minimum number of inclusions.
- 28 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessDetermining the Influence of Technological Parameters of the Electron-Beam Surfacing Process on Quality Indicators
This paper reports the technology and equipment designed for manufacturing parts and components with predefined properties by 3D printing methods. Underlying the technology is the use of a beam of high-power electrons to smelt metal powder in a vacuum chamber with the formation of successive layers that repeat the contours of the digital model of the article. The object of research is the process of surfacing articles from the Ti6Al4Vtitanium alloy powder. The purpose is to determine the optimal surfacing modes based on identifying the effect of process parameters on the quality indicators of articles. The result of the study is the analyzed influence of technological parameters on the properties of articles. The optimum energy density of the beam of 44.5 J/mm3has been determined. Based on the research results, 25 experimental samples were printed. Three beam speed modes were used: 270, 540, and 780 mm/s. For each mode, the dynamic focusing current varied from −1.2 to 1.27 A in increments of about 0.3 A. The articles were carefully examined. A method of raster electron microscopy was used to study the morphology of the samples' surfaces in several zones, namely in the central zone and along the contour; the roughness parameters of the surface micro relief, as well as the presence of defects (pores, non-melting, micro irregularities, inclusions), were established. It has been found that the articles are characterized mainly by a homogeneous micro relief of the profile. The structure of surfaces, formed in different zones depending on technological modes, differs in its morphology. Surfacing modes have been established that have the practical application: beam speed, 780 mm/s; power, 675 W; dynamic focus current, from –1.2 to 0 A. This provides for the minimal parameters of the surface micro relief and the absence of defects such as shrinkage pores, non-melting, as well as a minimum number of inclusions.
- Open Access
- 28 July 2026
- Published by Elsevier in SSRN Electronic Journal
Compensation of Spatial Deformation in Products at Additive Electron Beam Surfacing
The aim of the work is to analyze and optimize the shaping of GTE blade in the process of fabrication using additive electron beam technology. Using the method of computer simulation in the Simufact Additive software, the influence of technological printing parameters on product shaping was investigated, and shrinkage phenomena that occur during the printing process were analyzed. The printing simulation was performed and the results were compared to the reference model. The optimized computer models of GTE blades were created. According to the calculation results, when optimized models are used, the deviation in the geometric dimensions of printed blades does not exceed the product size tolerances of ±0.3 mm.
- 28 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessCompensation of Spatial Deformation in Products at Additive Electron Beam Surfacing
The aim of the work is to analyze and optimize the shaping of GTE blade in the process of fabrication using additive electron beam technology. Using the method of computer simulation in the Simufact Additive software, the influence of technological printing parameters on product shaping was investigated, and shrinkage phenomena that occur during the printing process were analyzed. The printing simulation was performed and the results were compared to the reference model. The optimized computer models of GTE blades were created. According to the calculation results, when optimized models are used, the deviation in the geometric dimensions of printed blades does not exceed the product size tolerances of ±0.3 mm.
- Open Access
- 28 July 2026
- Published by Elsevier in SSRN Electronic Journal
Additive Electron Beam Technology for Manufacture of Metal Products from Powder Materials
The aim of the work is to create additive electron beam technology for layer-by-layer manufacture of metal parts from powder materials. To carry out investigations, an experimental model of additive equipment was made, a software and hardware platform for additive manufacturing was designed, technological methods and modes of printing products of a set shape with predicted strength properties were invented. Applying the additive method, 25 experimental samples for further tests were printed. For each of the products, the speed of beam movement, its power and dynamic focusing current were determined. The influence of basic parameters of the technological process of surfacing on the formation and features of the surface structure and chemical composition of the samples were studied. It was found that the chemical composition of products corresponds to the composition of raw materials except for the content of aluminium, which is underestimated by 0.6‒1.96 % relative to the chemical composition of the powder. To eliminate this drawback, it is necessary to maintain the aluminium content in titanium alloy powders at the highest level. According to the results of investigations in the created equipment, according to computer models, the products of industrial and medical purpose were printed, the printing modes of which are optimized. From the powders of titanium alloys, the models of stator blades of a gas turbine aircraft engine, human skull implant and bioprosthesis were manufactured.
- 28 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessAdditive Electron Beam Technology for Manufacture of Metal Products from Powder Materials
The aim of the work is to create additive electron beam technology for layer-by-layer manufacture of metal parts from powder materials. To carry out investigations, an experimental model of additive equipment was made, a software and hardware platform for additive manufacturing was designed, technological methods and modes of printing products of a set shape with predicted strength properties were invented. Applying the additive method, 25 experimental samples for further tests were printed. For each of the products, the speed of beam movement, its power and dynamic focusing current were determined. The influence of basic parameters of the technological process of surfacing on the formation and features of the surface structure and chemical composition of the samples were studied. It was found that the chemical composition of products corresponds to the composition of raw materials except for the content of aluminium, which is underestimated by 0.6‒1.96 % relative to the chemical composition of the powder. To eliminate this drawback, it is necessary to maintain the aluminium content in titanium alloy powders at the highest level. According to the results of investigations in the created equipment, according to computer models, the products of industrial and medical purpose were printed, the printing modes of which are optimized. From the powders of titanium alloys, the models of stator blades of a gas turbine aircraft engine, human skull implant and bioprosthesis were manufactured.
- Open Access
- 28 July 2026
- Published by Elsevier in SSRN Electronic Journal
Determining the Influence of Technological Parameters of Electron Beam Surfacing Process on the Microstructure and Microhardness of Ti-6Al-4V Alloy
This paper reports the devised technology and equipment for manufacturing parts and assemblies with pre-defined properties by 3D printing methods. Underlying the technology is the application of a high-power electron beam to fuse metal powder in a vacuum chamber with the formation of successive layers that repeat the contours of the digital model of the product. The object of research is the process of surfacing products made of Ti6Al4V titanium alloy powder. The influence of technological parameters (speed and power of the electron beam) on the formation of the structure of the deposited metal and its mechanical properties was investigated. 3 samples printed under 3 modes were studied: beam speed, 270, 540, and 780 mm/s; power, 240, 495, and 675 W, respectively. The beam energy density was 44.5 J/mm3; the trajectory displacement step was 0.2 mm; the dynamic focusing current Idf was –0.31 A; and the powder layer thickness was 0.1 mm. The samples were examined by conventional methods. The structures were studied using an optical microscope, images were recorded with a camera. The Vickers hardness was measured with a microhardness meter in the direction from the technological supports to the surface of the sample, as well as along the surface of the product, and in the layers of the middle part of the sample. It was established that the articles had a dense cast structure of surfaced metal. On all samples, large crystallites with a uniform lamellar-acicular structure of α´-phase with a small amount of β-phase are formed along the height, mostly without defects with uniform microhardness both along the height and along the surface. It was determined that the surfacing mode at beam speed, 240 mm/s; power, 270 W is the most rational for practical use. Under this mode, a stronger structure is formed when it is crushed, reducing the width of the crystallites by 1.55 and 1.17 times compared to other modes
- 28 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessDetermining the Influence of Technological Parameters of Electron Beam Surfacing Process on the Microstructure and Microhardness of Ti-6Al-4V Alloy
This paper reports the devised technology and equipment for manufacturing parts and assemblies with pre-defined properties by 3D printing methods. Underlying the technology is the application of a high-power electron beam to fuse metal powder in a vacuum chamber with the formation of successive layers that repeat the contours of the digital model of the product. The object of research is the process of surfacing products made of Ti6Al4V titanium alloy powder. The influence of technological parameters (speed and power of the electron beam) on the formation of the structure of the deposited metal and its mechanical properties was investigated. 3 samples printed under 3 modes were studied: beam speed, 270, 540, and 780 mm/s; power, 240, 495, and 675 W, respectively. The beam energy density was 44.5 J/mm3; the trajectory displacement step was 0.2 mm; the dynamic focusing current Idf was –0.31 A; and the powder layer thickness was 0.1 mm. The samples were examined by conventional methods. The structures were studied using an optical microscope, images were recorded with a camera. The Vickers hardness was measured with a microhardness meter in the direction from the technological supports to the surface of the sample, as well as along the surface of the product, and in the layers of the middle part of the sample. It was established that the articles had a dense cast structure of surfaced metal. On all samples, large crystallites with a uniform lamellar-acicular structure of α´-phase with a small amount of β-phase are formed along the height, mostly without defects with uniform microhardness both along the height and along the surface. It was determined that the surfacing mode at beam speed, 240 mm/s; power, 270 W is the most rational for practical use. Under this mode, a stronger structure is formed when it is crushed, reducing the width of the crystallites by 1.55 and 1.17 times compared to other modes
- Open Access
- 28 July 2026
- Published by Elsevier in SSRN Electronic Journal
Determining Technological Parameters for Obtaining Ta15 Titanium Alloy Blanks with Improved Mechanical Characteristics Using the Electron-Beam 3d Printing Method
The object of this study is the process of electron beam 3D printing of articles made of TA15 titanium alloy powder. Peculiarities of the structure and properties formation of alloy blanks, obtained by this method have been described. Influence of process parameters (electron beam power and geometric scanning parameters) on the characteristics of the material were considered. Step of displacement of the beam trajectory changed from 0.1 to 0.25 mm with an interval of 0.05 mm. Specific energy of the electron beam varied from 20 to 70 J/mm3 for every trajectory displacement step. The macrostructure was examined visually while the microstructure was studied by optical microscopy. Mechanical properties were determined by uniaxial tension and impact bending tests. It was established that depending on the 3D printing parameters the macrostructure of most samples is dense but with unfavorable parameters non-fusions or shrinkage porosity defects may form. The microstructure of the dendritic type has an α´+β lamellar-acicular morphology, its dispersity and shape of α´–phase areas vary depending on the process parameters. A scanning step of 0.2 mm and a beam energy of 40 J/mm3 allows obtaining a dispersed microstructure in which there are no non-fusions and shrinkage micropores. The value of the Rm is 27 %, and the R0.2 is 24 % higher than that of the alloy obtained by the conventional technology of electron beam melting. The A5 is 3.2 times higher. However, impact toughness of the sample with dendrite unfavorable orientation to the direction of load applying may be lower compared to conventional technology. The results could be used for devising commercial technology of high strength titanium alloys parts produced by 3D printing
- 28 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessDetermining Technological Parameters for Obtaining Ta15 Titanium Alloy Blanks with Improved Mechanical Characteristics Using the Electron-Beam 3d Printing Method
The object of this study is the process of electron beam 3D printing of articles made of TA15 titanium alloy powder. Peculiarities of the structure and properties formation of alloy blanks, obtained by this method have been described. Influence of process parameters (electron beam power and geometric scanning parameters) on the characteristics of the material were considered. Step of displacement of the beam trajectory changed from 0.1 to 0.25 mm with an interval of 0.05 mm. Specific energy of the electron beam varied from 20 to 70 J/mm3 for every trajectory displacement step. The macrostructure was examined visually while the microstructure was studied by optical microscopy. Mechanical properties were determined by uniaxial tension and impact bending tests. It was established that depending on the 3D printing parameters the macrostructure of most samples is dense but with unfavorable parameters non-fusions or shrinkage porosity defects may form. The microstructure of the dendritic type has an α´+β lamellar-acicular morphology, its dispersity and shape of α´–phase areas vary depending on the process parameters. A scanning step of 0.2 mm and a beam energy of 40 J/mm3 allows obtaining a dispersed microstructure in which there are no non-fusions and shrinkage micropores. The value of the Rm is 27 %, and the R0.2 is 24 % higher than that of the alloy obtained by the conventional technology of electron beam melting. The A5 is 3.2 times higher. However, impact toughness of the sample with dendrite unfavorable orientation to the direction of load applying may be lower compared to conventional technology. The results could be used for devising commercial technology of high strength titanium alloys parts produced by 3D printing
- Open Access
- 27 July 2026
- Published by Elsevier in SSRN Electronic Journal
Electron Beam Powder Bed Fusion of VT6 Titanium Alloy for Aircraft Applications
This study investigates components produced by additive electron beam powder bed fusion (EB-PBF) technology using VT6 (Ti 6Al 4V) titanium alloy. A material widely employed in aerospace applications due to its weldability, strength, and fatigue resistance. A key challenge remains achieving high density, uniform microstructure and stable operational properties in manufactured parts. To address this, digital modeling of the aircraft gas turbine engines (GTE) parts was performed in Materialise Magics and process optimization in Simufact Additive. Experimental samples included a turbine wheel, four turbine blades and reference specimens. Chemical analysis confirmed alloy compliance, while microstructural studies revealed a lamellar α′-phase with needle like morphology (0.5–1.5 μm) and minor β phase content. Alloying elements were evenly distributed, with no segregation or porosity; average microhardness HV0.1 reached 3.71 GPa. The results demonstrate that the manufactured parts meet GTE requirements, showing high density, strength, and reliability. Integration of digital modeling with 3D printing and optimized parameters enabled the production of components with fully dense structure, stable microstructure, controlled texture and high geometric accuracy, highlighting the effectiveness and scalability of this approach for serial production of critical aerospace part
- 27 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessElectron Beam Powder Bed Fusion of VT6 Titanium Alloy for Aircraft Applications
This study investigates components produced by additive electron beam powder bed fusion (EB-PBF) technology using VT6 (Ti 6Al 4V) titanium alloy. A material widely employed in aerospace applications due to its weldability, strength, and fatigue resistance. A key challenge remains achieving high density, uniform microstructure and stable operational properties in manufactured parts. To address this, digital modeling of the aircraft gas turbine engines (GTE) parts was performed in Materialise Magics and process optimization in Simufact Additive. Experimental samples included a turbine wheel, four turbine blades and reference specimens. Chemical analysis confirmed alloy compliance, while microstructural studies revealed a lamellar α′-phase with needle like morphology (0.5–1.5 μm) and minor β phase content. Alloying elements were evenly distributed, with no segregation or porosity; average microhardness HV0.1 reached 3.71 GPa. The results demonstrate that the manufactured parts meet GTE requirements, showing high density, strength, and reliability. Integration of digital modeling with 3D printing and optimized parameters enabled the production of components with fully dense structure, stable microstructure, controlled texture and high geometric accuracy, highlighting the effectiveness and scalability of this approach for serial production of critical aerospace part
- Open Access
- 27 July 2026
- Published by Elsevier in SSRN Electronic Journal
Application of Additive Electron Beam Technologies for Manufacture of Metal Products
The prospects of manufacturing a wide range of parts and units were noted using electron beam technologies. In the work the features of creating such technology are considered using the domestic raw materials in the form of powder materials or filler wire. In the laboratory equipment the cylindrical and rectangular specimens were manufactured, thus proving the possibility of implementing the additive technology for the needs of industry. Keywords-electron beam surfacing, products of specified shape, 3D-printing method, powder materials, filler wires, laboratory equipment.
- 27 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessApplication of Additive Electron Beam Technologies for Manufacture of Metal Products
The prospects of manufacturing a wide range of parts and units were noted using electron beam technologies. In the work the features of creating such technology are considered using the domestic raw materials in the form of powder materials or filler wire. In the laboratory equipment the cylindrical and rectangular specimens were manufactured, thus proving the possibility of implementing the additive technology for the needs of industry. Keywords-electron beam surfacing, products of specified shape, 3D-printing method, powder materials, filler wires, laboratory equipment.
- Open Access
- 30 October 2025
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 5 (12 (137)) , 36-46
Determining the properties of gas turbine engine components manufactured from VT6 titanium alloy powder (Ti-6Al-4V) by using additive electron beam technology
This study considers components manufactured by additive electron beam manufacturing (EBM) from Ti-6Al-4V (VT6) titanium alloy powder. This material is one of the most widely used in aircraft engine production due to its combination of high weldability, strength, as well as resistance to fatigue loading. The task addressed is to achieve consistently high density, structural uniformity, and stable operational properties in gas turbine engines (GTEs) components manufactured from VT6 alloy by the EBM method. To fabricate specimens, a digital model was constructed in Materialise Magics, while layer-by-layer analysis and optimization of process parameters were carried out in Simufact Additive. Using the EBM process, experimental specimens were produced, including four GTE blades, a turbine wheel, and control samples. The chemical composition confirmed full compliance of the parts with the VT6 (Ti-6Al-4V) alloy standard. The microstructure is characterized by a lamellar α′-phase with a minor fraction of β-phase; the α-phase exhibits an acicular morphology with crystal thickness ranging from 0.5 to 1.5 μm. A uniform distribution of alloying elements, as well as the absence of segregation and porosity, was observed. The average microhardness value HV100 was determined to be 3.71 GPa. The results confirmed that the manufactured parts met the requirements for GTE components, demonstrating high density, strength, and operational reliability. The integration of simulation with subsequent EBM fabrication, optimization of process parameters, and the use of produced VT6 powder enabled the production of parts with zero porosity and stable microstructure. The components also showed controlled texture and high geometric accuracy. This confirms the effectiveness of the proposed approach and highlights its potential for scaling into serial production of critical components with predictable performance characteristics
- 30 October 2025
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 5 (12 (137)) , 36-46
Open AccessDetermining the properties of gas turbine engine components manufactured from VT6 titanium alloy powder (Ti-6Al-4V) by using additive electron beam technology
This study considers components manufactured by additive electron beam manufacturing (EBM) from Ti-6Al-4V (VT6) titanium alloy powder. This material is one of the most widely used in aircraft engine production due to its combination of high weldability, strength, as well as resistance to fatigue loading. The task addressed is to achieve consistently high density, structural uniformity, and stable operational properties in gas turbine engines (GTEs) components manufactured from VT6 alloy by the EBM method. To fabricate specimens, a digital model was constructed in Materialise Magics, while layer-by-layer analysis and optimization of process parameters were carried out in Simufact Additive. Using the EBM process, experimental specimens were produced, including four GTE blades, a turbine wheel, and control samples. The chemical composition confirmed full compliance of the parts with the VT6 (Ti-6Al-4V) alloy standard. The microstructure is characterized by a lamellar α′-phase with a minor fraction of β-phase; the α-phase exhibits an acicular morphology with crystal thickness ranging from 0.5 to 1.5 μm. A uniform distribution of alloying elements, as well as the absence of segregation and porosity, was observed. The average microhardness value HV100 was determined to be 3.71 GPa. The results confirmed that the manufactured parts met the requirements for GTE components, demonstrating high density, strength, and operational reliability. The integration of simulation with subsequent EBM fabrication, optimization of process parameters, and the use of produced VT6 powder enabled the production of parts with zero porosity and stable microstructure. The components also showed controlled texture and high geometric accuracy. This confirms the effectiveness of the proposed approach and highlights its potential for scaling into serial production of critical components with predictable performance characteristics