OBOlena M. Berdnikova

Olena M. Berdnikova

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Olena M. Berdnikova has a total of 107 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Determining structure formation patterns in vt6 titanium alloy at electron beam powder bed fusion

    by Vladyslav Matviichuk, Vladimir Nesterenkov, Olena Berdnikova

    This study refines the process that defines the microstructure and mechanical properties of samples manufactured by additive electron-beam melting (EBM) from the titanium alloy VT6 powder of the Ti-6Al-4V system. The task addressed is to establish regularities in the VT6 alloy structuring, thereby determining the relationship between the parameters of the additive process, the αʹ-phase morphology, defectivity, and mechanical properties. The spherical titanium alloy VT6 powder with a particle size of 40–160 μm was used as the raw material. 50 samples measuring 25 × 25 mm and 7.5 mm high were studied. For an electron beam energy density of 15–40 J/mm3 in the range of scanning speeds from 500 mm/s to 12000 mm/s, technological modes were determined that ensure a smooth surface morphology of articles. It is noted that the material of the samples is characterized by a layered structure with a uniform chemical composition. The microstructure of grains in the deposited metal in all samples consists of a lamellar αʹ-phase and a small amount of β-phase. The sizes of lamellar components vary depending on the technological parameters. The microhardness level is in the range HV = 192.1…392.42 with a relatively uniform distribution of values. The following rational printing modes have been established: 500 mm/s / 40 J/mm3, 4000 mm/s / 24 J/mm3, 6000 mm/s / 18 J/mm3, and 8000 mm/s / 16 J/mm3. They enable the formation of a structural state of the metal with minimal defects, a dispersed α′-structure, and a uniform distribution of microhardness. The results demonstrate that the combination of high-quality powder material and rational printing mode provides high process reproducibility, structural stability, and suitability of the technology for manufacturing articles with predicted characteristics

  • Specific features of the 25KhGNMT structural steel surface after treatment with pulse barrier discharge

    by L. M. Lobanov, M. O. Pashchyn, O. М. Berdnikova, О. S. Kushnarova, V. O. Bereka, O. L. Mikhodui

    The use of electrophysical processing methods for metal materials to improve the mechanical properties of metal and alloy products is a promising direction for the development of surface strengthening processes. The use of pulsed barrier discharge (PBD), which generates low-temperature plasma on the metal surface during processing is a new approach in metalworking. The effect of PBD on structural changes at the dislocation level and their influence on the physicomechanical properties of 25KhGNMT steel after its surface treatment is studied. The features of the structure formed in the surface layers of the treated metal are analyzed. The research shows that, compared to untreated metal, noticeable structural and phase changes are observed in the surface treated with PBD up to a thickness of 2200 mkm: the formation of a martensite-bainite structure with an increase in the volume fraction of lower bainite; fragmentation of rail structural components; formation of a substructure with a generally uniform distribution of dislocation density and the absence of local internal stress concentrators. This provides surface strengthening and crack-growth resistance of structural steel.

  • Open Access

    Determining the Influence of Technological Parameters of the Electron-Beam Surfacing Process on Quality Indicators

    by Vladyslav Matviichuk, Vladimir Nesterenkov, Olena Berdnikova

    This paper reports the technology and equipment designed for manufacturing parts and components with predefined properties by 3D printing methods. Underlying the technology is the use of a beam of high-power electrons to smelt metal powder in a vacuum chamber with the formation of successive layers that repeat the contours of the digital model of the article. The object of research is the process of surfacing articles from the Ti6Al4Vtitanium alloy powder. The purpose is to determine the optimal surfacing modes based on identifying the effect of process parameters on the quality indicators of articles. The result of the study is the analyzed influence of technological parameters on the properties of articles. The optimum energy density of the beam of 44.5 J/mm3has been determined. Based on the research results, 25 experimental samples were printed. Three beam speed modes were used: 270, 540, and 780 mm/s. For each mode, the dynamic focusing current varied from −1.2 to 1.27 A in increments of about 0.3 A. The articles were carefully examined. A method of raster electron microscopy was used to study the morphology of the samples' surfaces in several zones, namely in the central zone and along the contour; the roughness parameters of the surface micro relief, as well as the presence of defects (pores, non-melting, micro irregularities, inclusions), were established. It has been found that the articles are characterized mainly by a homogeneous micro relief of the profile. The structure of surfaces, formed in different zones depending on technological modes, differs in its morphology. Surfacing modes have been established that have the practical application: beam speed, 780 mm/s; power, 675 W; dynamic focus current, from –1.2 to 0 A. This provides for the minimal parameters of the surface micro relief and the absence of defects such as shrinkage pores, non-melting, as well as a minimum number of inclusions.

  • Open Access

    Additive Electron Beam Technology for Manufacture of Metal Products from Powder Materials  

    by Vladyslav Matviichuk, Vladimir Nesterenkov, Olena Berdnikova

    The aim of the work is to create additive electron beam technology for layer-by-layer manufacture of metal parts from powder materials. To carry out investigations, an experimental model of additive equipment was made, a software and hardware platform for additive manufacturing was designed, technological methods and modes of printing products of a set shape with predicted strength properties were invented. Applying the additive method, 25 experimental samples for further tests were printed. For each of the products, the speed of beam movement, its power and dynamic focusing current were determined. The influence of basic parameters of the technological process of surfacing on the formation and features of the surface structure and chemical composition of the samples were studied. It was found that the chemical composition of products corresponds to the composition of raw materials except for the content of aluminium, which is underestimated by 0.6‒1.96 % relative to the chemical composition of the powder. To eliminate this drawback, it is necessary to maintain the aluminium content in titanium alloy powders at the highest level. According to the results of investigations in the created equipment, according to computer models, the products of industrial and medical purpose were printed, the printing modes of which are optimized. From the powders of titanium alloys, the models of stator blades of a gas turbine aircraft engine, human skull implant and bioprosthesis were manufactured.

  • Open Access

    Determining the Influence of Technological Parameters of Electron Beam Surfacing Process on the Microstructure and Microhardness of Ti-6Al-4V Alloy

    by Vladyslav Matviichuk, Vladimir Nesterenkov, Olena Berdnikova

    This paper reports the devised technology and equipment for manufacturing parts and assemblies with pre-defined properties by 3D printing methods. Underlying the technology is the application of a high-power electron beam to fuse metal powder in a vacuum chamber with the formation of successive layers that repeat the contours of the digital model of the product. The object of research is the process of surfacing products made of Ti6Al4V titanium alloy powder. The influence of technological parameters (speed and power of the electron beam) on the formation of the structure of the deposited metal and its mechanical properties was investigated. 3 samples printed under 3 modes were studied: beam speed, 270, 540, and 780 mm/s; power, 240, 495, and 675 W, respectively. The beam energy density was 44.5 J/mm3; the trajectory displacement step was 0.2 mm; the dynamic focusing current Idf was –0.31 A; and the powder layer thickness was 0.1 mm. The samples were examined by conventional methods. The structures were studied using an optical microscope, images were recorded with a camera. The Vickers hardness was measured with a microhardness meter in the direction from the technological supports to the surface of the sample, as well as along the surface of the product, and in the layers of the middle part of the sample. It was established that the articles had a dense cast structure of surfaced metal. On all samples, large crystallites with a uniform lamellar-acicular structure of α´-phase with a small amount of β-phase are formed along the height, mostly without defects with uniform microhardness both along the height and along the surface. It was determined that the surfacing mode at beam speed, 240 mm/s; power, 270 W is the most rational for practical use. Under this mode, a stronger structure is formed when it is crushed, reducing the width of the crystallites by 1.55 and 1.17 times compared to other modes

  • Optimization of silicon and aluminum content for improving properties of the heat-affected zone metal of high-hardness Cr–Ni–Mo steels

    by O. S. Kushnarova, V. А. Kostin, V. D. Poznyakov, I. I. Alekseienko, T. O. Alekseienko, O. M. Berdnikova

    The choice of the Cr–Ni–Mo alloying system for high (450–550 HB) and ultra-high (> 600 HB) hardness steels, taking into account the influence of silicon (Si) and aluminum (Al) on the properties depending on the thickness of the protective elements of the struc¬ture is substantiated. To decrease steel intensity of the protection system against high-energy impacts, it is sufficient to use plates with a thickness of 20 mm and the maxi¬mum silicon content in the steel is of priority to ensure its surface hardness. It is shown that for t < 20 mm, an increased Si content is advisable to ensure high surface hard¬ness, while for t > 20 mm the through-hardenability and impact toughness are determining factors. This is achieved by an increased Al content due to the grain refinement of austenite. The influence of the Al/Si content ratio on the combination of mechanical pro¬perties and microstructure stability, in particular in the heat-affected zone of welded joints, is analyzed. The need for a differentiated approach to choosing an alloying system and optimizing the Al/Si content ratio in accordance with the thickness of the protective struc¬tural elements and expected failure mechanisms is substantiated.

  • Features of the Formation of the Structure of Welded Joints of Structural Steels during Underwater Welding with Filler Wire 12X18N9T Using External Electromagnetic Influence

    by Sergey Maksimov, Olena A. Prilipko, Olena M. Berdnikova, Olga Kushnarova, Igor Alekseenko

    During underwater wet welding, the environment has a corresponding effect on the mechanical properties of the weld metal. The use of external electromagnetic action (EEA) during welding is promising for influencing the formation of welded joints and the structure formation in physically inhomogeneous environments. Experimental studies have demonstrated the effectiveness of EEA application in reducing the tendency of weld metal to form pores, enhancing degassing, and lowering hydrogen content etc. The paper presents a metallographic study of the welded joint metal of structural steel (St3) after underwater welding with 12Kh18N9T filler wire, both without and with the use of EEA. Based on calculation methods and predictive modelling, optimal operating modes of the electromagnetic system for an experimental study of the EEA effect during underwater welding have been established and implemented. It has been established that the weld metal mainly has a ferrite-pearlite structure, while an austenitic structure with elongated grains is formed in the weld metal. When using the EEA, the grain structure of the weld metal is refined by an average of 1.5 times with an insignificant decrease in microhardness. In the heat-affected zone (HAZ), in the areas of large grain (I HAZ), recrystallisation (II HAZ) and incomplete recrystallisation (III HAZ), a bainitic structure is formed in the presence of ferrite layers. Under the influence of the EEA, the grain size is refined by 1.2 times in the I HAZ and II HAZ with a decrease in the thickness of ferrite layers and an increase in microhardness by an average of 7 ... 10%. The formation of such a structure will provide a set of strength properties and toughness of the welded joint metal. Research has proven that the technology of wet welding under water using the EEA allows for the production of high-quality welded joints with a high set of physical and mechanical properties of the metal of both welded joints and the HAZ.

  • Structure and Properties of Experimental Low-Cost Titanium Alloys

    by Svitlana Hryhorenko, Olena M. Berdnikova, Olga Kushnarova, Valery Kostin, Yevhenii Titkov, Liubov Yeremeieva

    Phase components of experimental low cost titanium alloys, their substructure and parameters, dislocation structure, features of phase formation in the metal, which differ in alloying systems, were studied using complex research methods. The stoichiometric composition of dispersed phases in the internal volumes of alloy grains was determined by diffraction patterns using transmission electron microscopy. It is shown that in the structure of titanium alloy Ti-2,8Al-5,1Mo-4,9Fe there are dispersed nanoparticles of intermetallic phases of different morphology and stoichiometric composition. These are the phases: Ti 3 Al and Fe 2 Ti with a size of 10…40 nm; Mo 9 Ti 4 - 20…120 nm. Studies of titanium alloy Ti-1,5Fe-O showed the presence in the structure of mainly nanoparticles of oxides: Ti 3 O 5 size 10…30 nm and Ti 4 Fe 2 O, FeTiO 5 (10…90 nm), as well as intermetallics Fe 2 Ti (10…40 nm). It is established that the formation of nanoparticles of intermetallic and oxide phases in the thin plate structure of the investigated experimental low cost titanium alloys promotes the formation of the substructure with uniform distribution of dislocation density. This provides a high level of mechanical properties of alloys.