Shahnor Basri
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Shahnor Basri has a total of 122 co-authors. Here are the top co-authors by number of shared publications:
- Faizal Mustapha
Department of Aerospace Engineering, Faculty of Engineering, Universiti Putra Malaysia, Serdang 43400, Malaysia
9 shared publications - Behzad Bahraminejad
Department of Electrical Engineering, Majlesi Branch, Islamic Azad University, Esfahan, Iran
6 shared publications - Maryam Mohd Isa
Universiti Putra Malaysia
6 shared publications Dewan Muhammad Nuruzzaman
4 shared publications- Mohamed Thariq Hameed Sultan
Department of Aerospace Engineering, Faculty of Engineering, Universiti Putra Malaysia (UPM), Serdang 43400, Selangor, Malaysia
4 shared publications Waqar Asrar
4 shared publications
Latest Publications
- Open Access
- 6 April 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 342 (1) , 012063
Preparation and characterization of 6-layered functionally graded nickel-alumina (Ni-Al2O3) composites
- 6 April 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 342 (1) , 012063
Open AccessPreparation and characterization of 6-layered functionally graded nickel-alumina (Ni-Al2O3) composites
- 1 April 2018
- Published by Jaypee Brothers Medical Publishing in World Journal of Dentistry
- Vol. 9 (2) , 137-144
Functionally Graded Materials: An Overview of Dental Applications
- 1 April 2018
- Published by Jaypee Brothers Medical Publishing in World Journal of Dentistry
- Vol. 9 (2) , 137-144
Functionally Graded Materials: An Overview of Dental Applications
- 20 March 2017
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 889, 90-95
Phase Contamination Characterization of Stepwise-Built Functionally Graded Hydroxyapatite/Titanium (HA/Ti) Sintered under Various Atmospheres
Fourier Transform Infrared Spectroscopy (FTIR) and X-Ray Diffraction (XRD) test were utilized to detect the phase transformation of a HA/Ti Functionally Graded Material (FGM) prepared via Powder Metallurgy (PM) technique. The effects of oxygen (O2), nitrogen (N2), forming (N2+H2) and Argon (Ar) sintering atmospheres on the FGM specimens were examined by considering the gas flowing duration. It was found that the original metallurgical profile of pure Ti in HA/Ti FGM sintered under N2 atmosphere was almost preserved. However the carburization of the pure Ti was observed on the specimen. Medium alkyl halides (C-Br) and alkenes (-C=C-) stretches were detected, producing the dominant elements in the pure Ti layer of the specimen. The almost stable constituent element remains in the specimen sintered under flowing N2+H2 atmosphere as detected by XRD result. This proved the significance of controlling the sintering atmosphere during the entire sintering process. The results achieved reveal the high tendency of Ti and HA elements to react with the sintering environment, thus very precise furnace with controllable atmosphere is crucial for the fabrication of the HA/Ti FGM.
- 20 March 2017
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 889, 90-95
Phase Contamination Characterization of Stepwise-Built Functionally Graded Hydroxyapatite/Titanium (HA/Ti) Sintered under Various Atmospheres
Fourier Transform Infrared Spectroscopy (FTIR) and X-Ray Diffraction (XRD) test were utilized to detect the phase transformation of a HA/Ti Functionally Graded Material (FGM) prepared via Powder Metallurgy (PM) technique. The effects of oxygen (O2), nitrogen (N2), forming (N2+H2) and Argon (Ar) sintering atmospheres on the FGM specimens were examined by considering the gas flowing duration. It was found that the original metallurgical profile of pure Ti in HA/Ti FGM sintered under N2 atmosphere was almost preserved. However the carburization of the pure Ti was observed on the specimen. Medium alkyl halides (C-Br) and alkenes (-C=C-) stretches were detected, producing the dominant elements in the pure Ti layer of the specimen. The almost stable constituent element remains in the specimen sintered under flowing N2+H2 atmosphere as detected by XRD result. This proved the significance of controlling the sintering atmosphere during the entire sintering process. The results achieved reveal the high tendency of Ti and HA elements to react with the sintering environment, thus very precise furnace with controllable atmosphere is crucial for the fabrication of the HA/Ti FGM.
- Open Access
- 1 February 2016
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 114 (1) , 012118
Experimental investigation on the mechanical properties of glass fiber reinforced nylon
Damage localization in a glass fiber reinforced composite plate
- 1 February 2016
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 114 (1) , 012118
Open AccessExperimental investigation on the mechanical properties of glass fiber reinforced nylon
Damage localization in a glass fiber reinforced composite plate
- Open Access
- 1 February 2016
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 114 (1) , 012104
Al-TiH2Composite Foams Magnesium Alloy
The work presented here in describes the synthesis of aluminum based titanium-hydride particulate composite by casting method and its foaming behavior of magnesium alloy. Results obtained indicate that the Al-10TiH2 composite can be synthesized successfully by casting method. Further, results also reveal that closed-cell magnesium alloy foam can be synthesized by using Al-10TiH2 composite as a foaming agent.
- 1 February 2016
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 114 (1) , 012104
Open AccessAl-TiH2Composite Foams Magnesium Alloy
The work presented here in describes the synthesis of aluminum based titanium-hydride particulate composite by casting method and its foaming behavior of magnesium alloy. Results obtained indicate that the Al-10TiH2 composite can be synthesized successfully by casting method. Further, results also reveal that closed-cell magnesium alloy foam can be synthesized by using Al-10TiH2 composite as a foaming agent.
- Open Access
- 1 February 2016
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 114 (1) , 012012
CAE applications in a thermoforming mould design
Preparation of honeycomb layer is a critical step for successful fabrications of thermoformed based sandwiched structures. This paper deals with an initial investigation on the rapid manufacturing process of corrugated sheet with 120° dihedral angles. Time history of local displacements and thickness, assuming viscous dominated material model for a 1mm thick thermoformable material, was computed by using ANSYS® Polyflow solver. The quality of formed surfaces was evaluated for selection of mould geometry and assessment of two common variants of thermoforming process. Inadequate mesh refinement of a membrane elements produces satisfactorily detailing and incomplete forming. A perfectly uniform material distribution was predicted using drape forming process. However, the geometrical properties of vacuum formed part are poorly distributed and difficult to control with increasing inflation volumes. Details of the discrepancies and the contributions of the CAE tool to complement traditional trial and error methodology in the process and design development are discussed.
- 1 February 2016
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 114 (1) , 012012
Open AccessCAE applications in a thermoforming mould design
Preparation of honeycomb layer is a critical step for successful fabrications of thermoformed based sandwiched structures. This paper deals with an initial investigation on the rapid manufacturing process of corrugated sheet with 120° dihedral angles. Time history of local displacements and thickness, assuming viscous dominated material model for a 1mm thick thermoformable material, was computed by using ANSYS® Polyflow solver. The quality of formed surfaces was evaluated for selection of mould geometry and assessment of two common variants of thermoforming process. Inadequate mesh refinement of a membrane elements produces satisfactorily detailing and incomplete forming. A perfectly uniform material distribution was predicted using drape forming process. However, the geometrical properties of vacuum formed part are poorly distributed and difficult to control with increasing inflation volumes. Details of the discrepancies and the contributions of the CAE tool to complement traditional trial and error methodology in the process and design development are discussed.
- Open Access
- 1 February 2016
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 114 (1) , 012043
Modeling and flow analysis of pure nylon polymer for injection molding process
In the production of complex plastic parts, injection molding is one of the most popular industrial processes. This paper addresses the modeling and analysis of the flow process of the nylon (polyamide) polymer for injection molding process. To determine the best molding conditions, a series of simulations are carried out using Autodesk Moldflow Insight software and the processing parameters are adjusted. This mold filling commercial software simulates the cavity filling pattern along with temperature and pressure distributions in the mold cavity. In the modeling, during the plastics flow inside the mold cavity, different flow parameters such as fill time, pressure, temperature, shear rate and warp at different locations in the cavity are analyzed. Overall, this Moldflow is able to perform a relatively sophisticated analysis of the flow process of pure nylon. Thus the prediction of the filling of a mold cavity is very important and it becomes useful before a nylon plastic part to be manufactured.
- 1 February 2016
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 114 (1) , 012043
Open AccessModeling and flow analysis of pure nylon polymer for injection molding process
In the production of complex plastic parts, injection molding is one of the most popular industrial processes. This paper addresses the modeling and analysis of the flow process of the nylon (polyamide) polymer for injection molding process. To determine the best molding conditions, a series of simulations are carried out using Autodesk Moldflow Insight software and the processing parameters are adjusted. This mold filling commercial software simulates the cavity filling pattern along with temperature and pressure distributions in the mold cavity. In the modeling, during the plastics flow inside the mold cavity, different flow parameters such as fill time, pressure, temperature, shear rate and warp at different locations in the cavity are analyzed. Overall, this Moldflow is able to perform a relatively sophisticated analysis of the flow process of pure nylon. Thus the prediction of the filling of a mold cavity is very important and it becomes useful before a nylon plastic part to be manufactured.
- 1 October 2014
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 629, 437-443
Effect of Sintering Temperature on Functionally Graded Nickel/Alumina Plate
Functionally graded material that consists of gradually changed dual-phase compositions along the thickness direction of its structure has been introduced as an answer to sharp interfaces problems occur while the processing. In order to observe the morphological and shrinkage due to the sintering process, the Ni/Al2O3 FG samples were manufactured via powder metallurgy routes under argon atmosphere. This study reveals that the sintering temperature does affects the sintering behaviors including the microstructures and radial dimensions of the FG plates. The numerical simulation is found to be useful to predict the stress concentration area within the structures and consequently improve the design of the FG plates.
- 1 October 2014
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 629, 437-443
Effect of Sintering Temperature on Functionally Graded Nickel/Alumina Plate
Functionally graded material that consists of gradually changed dual-phase compositions along the thickness direction of its structure has been introduced as an answer to sharp interfaces problems occur while the processing. In order to observe the morphological and shrinkage due to the sintering process, the Ni/Al2O3 FG samples were manufactured via powder metallurgy routes under argon atmosphere. This study reveals that the sintering temperature does affects the sintering behaviors including the microstructures and radial dimensions of the FG plates. The numerical simulation is found to be useful to predict the stress concentration area within the structures and consequently improve the design of the FG plates.