Johan Lönnqvist
Research Subjects
Johan Lönnqvist has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Anton Jansson
Swerim AB, 164 40 Stockholm, Sweden
2 shared publications - Bevis Hutchinson
Swerim AB
2 shared publications - Linda Bäcke
SSAB, 781 84 Borlänge, Sweden
2 shared publications - Mikael Malmström
Swerim AB, Kista, Sweden
2 shared publications - Chunhui Luo
Swerim AB, SE-164 40 Kista, Sweden
1 shared publication - David Lindell
Swerim AB, 164 40 Stockholm, Sweden
1 shared publication
Latest Publications
- Open Access
- 19 March 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (6) , 3901
Significance of Annealing Twins in Laser Ultrasonic Measurements of Grain Size in High-Strength Low-Alloy Steels
In this study, we demonstrate the significance of austenite annealing twin boundaries when calibrating laser ultrasonic measurements for gauging austenite grain size in situ during the thermomechanical processing of high-strength low-alloy steels. Simple calculations show how differences in twinning density can lead to errors in grain size measurements if twins are disregarded during calibration and the method is used for a broad range of steels. Conversely, when calibration is performed using alloys with a metastable austenite microstructure at room temperature, the same calibration is suitable for a broad range of HSLA steels, provided that annealing twins are taken into account. Since light optical microscopy does not allow the characterization of annealing twins in low-alloy steel, the verification of the laser ultrasonic results was conducted using the novel approach of comparing the twinned grain sizes obtained using the ultrasonic method in low-alloy steels with the austenite grain maps reconstructed from martensite orientation maps measured using electron backscatter diffraction. Finally, we show how differences in twinning density occur even for alloys with a roughly similar stacking fault energy, further highlighting the importance of annealing twins in the calibration of laser ultrasonic measurements for industrial use.
- 19 March 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (6) , 3901
Open AccessSignificance of Annealing Twins in Laser Ultrasonic Measurements of Grain Size in High-Strength Low-Alloy Steels
In this study, we demonstrate the significance of austenite annealing twin boundaries when calibrating laser ultrasonic measurements for gauging austenite grain size in situ during the thermomechanical processing of high-strength low-alloy steels. Simple calculations show how differences in twinning density can lead to errors in grain size measurements if twins are disregarded during calibration and the method is used for a broad range of steels. Conversely, when calibration is performed using alloys with a metastable austenite microstructure at room temperature, the same calibration is suitable for a broad range of HSLA steels, provided that annealing twins are taken into account. Since light optical microscopy does not allow the characterization of annealing twins in low-alloy steel, the verification of the laser ultrasonic results was conducted using the novel approach of comparing the twinned grain sizes obtained using the ultrasonic method in low-alloy steels with the austenite grain maps reconstructed from martensite orientation maps measured using electron backscatter diffraction. Finally, we show how differences in twinning density occur even for alloys with a roughly similar stacking fault energy, further highlighting the importance of annealing twins in the calibration of laser ultrasonic measurements for industrial use.
- Open Access
- 6 October 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (19) , 10048
Laser-Ultrasound-Based Grain Size Gauge for the Hot Strip Mill
The paper summarizes the creation of a robust online grain size gauge for a hot strip mill. A method and algorithm for calculating the grain size from the measured ultrasonic attenuation is presented. This new method is self-calibrating, does not rely on a geometrical reference sample and can cope with the effects of diffraction on the attenuation. The model is based on 52 quenched samples measured with more than 23,000 laser ultrasonics shots and has a correlation coefficient R2 of 0.8. Typical online laser ultrasonic measurements from the hot strip mill and the calculated grain size versus length are presented for a couple of steel strips.
- 6 October 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (19) , 10048
Open AccessLaser-Ultrasound-Based Grain Size Gauge for the Hot Strip Mill
The paper summarizes the creation of a robust online grain size gauge for a hot strip mill. A method and algorithm for calculating the grain size from the measured ultrasonic attenuation is presented. This new method is self-calibrating, does not rely on a geometrical reference sample and can cope with the effects of diffraction on the attenuation. The model is based on 52 quenched samples measured with more than 23,000 laser ultrasonics shots and has a correlation coefficient R2 of 0.8. Typical online laser ultrasonic measurements from the hot strip mill and the calculated grain size versus length are presented for a couple of steel strips.
- Open Access
Interaction of Carbon, Titanium, and Boron in Micro-Alloy Steels and Its Effect on Hot Ductility
Varying contents of carbon, titanium and boron were used in the base steel composition of 0.30 wt% Si, 2.0 wt% Mn, 0.006 wt% S, 0.03 wt% Nb, and 30–35 ppm N. Hot ductility tests were performed with Gleeble-3800, after the steel sample was in-situ melted, solidified, and cooled to the test temperature. Investigation was completed with thermodynamic and kinetic simulations. The best results were obtained for steels containing 58–100 ppm B and 35 ppm Ti. They showed very good hot ductility of 80–50% RA within the temperature range between 1250 °C and 800 °C. It was shown that titanium and boron were effective in improving the hot ductility. Titanium protected boron from binding into BN and was low enough to prevent excessive (Ti,Nb) carbonitride precipitation, which both could decrease hot ductility. Boron that precipitated along austenite grain boundaries as iron boride Fe2B was very beneficial for the hot ductility of steel.
Open AccessInteraction of Carbon, Titanium, and Boron in Micro-Alloy Steels and Its Effect on Hot Ductility
Varying contents of carbon, titanium and boron were used in the base steel composition of 0.30 wt% Si, 2.0 wt% Mn, 0.006 wt% S, 0.03 wt% Nb, and 30–35 ppm N. Hot ductility tests were performed with Gleeble-3800, after the steel sample was in-situ melted, solidified, and cooled to the test temperature. Investigation was completed with thermodynamic and kinetic simulations. The best results were obtained for steels containing 58–100 ppm B and 35 ppm Ti. They showed very good hot ductility of 80–50% RA within the temperature range between 1250 °C and 800 °C. It was shown that titanium and boron were effective in improving the hot ductility. Titanium protected boron from binding into BN and was low enough to prevent excessive (Ti,Nb) carbonitride precipitation, which both could decrease hot ductility. Boron that precipitated along austenite grain boundaries as iron boride Fe2B was very beneficial for the hot ductility of steel.
- 21 June 2021
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 52 (9) , 3727-3749
The Mechanism for Coarse Nb-Rich Particle Formation in Steel
- 21 June 2021
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 52 (9) , 3727-3749
The Mechanism for Coarse Nb-Rich Particle Formation in Steel