S. Shamshath Begum
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
S. Shamshath Begum has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
Sandeep Kumar Shukla
Mahindra & Mahindra, Mahindra Research Valley, Chennai-603004, Tamil Nadu, India
2 shared publicationsAbbas Saifee Valsadwala
University of Akron
1 shared publication- Abbas Saifee Valsadwala
Department of Polymer Engineering, B. S. Abdur Rahman Crescent Institute of Science and Technology, Chennai-600048, Tamil Nadu, India
1 shared publication Asit Baran Samui
Institute of Chemical Technology
1 shared publication- Asit Baran Samui
Institute of Chemical Technology
1 shared publication - Balachandran Surya Rajan
Department of Mechanical Engineering B.S. Abdur Rahman Crescent Institute of Science and Technology Chennai Tamil Nadu India
1 shared publication
Latest Publications
- Open Access
- 1 October 2024
- Published by IOP Publishing in Materials Research Express
- Vol. 11 (10) , 105308
Investigating the influence of periwinkle shell powder on the thermal and mechanical performance of high-density polyethylene composites
In this study, the shell powder of Littorina littorea commonly called periwinkle was used as an eco-friendly filler in High-Density Polyethylene (HDPE) to form periwinkle/HDPE composites (PHPC). Understanding the effect of different particle sizes of periwinkle shell powder (PSP) and optimizing their influence on PHPC is the main scope of this work. Periwinkle shell (PS) particles with sizes ranging from L53, PHPC53, PHPC75, PHPC90, PHPC105, and PHPC150, respectively. The composites were fabricated by incorporating 1 wt% PSP into the HDPE matrix using the compression molding technique and then subjected to morphological, thermal, and mechanical characterizations. Morphology studies using scanning electron microscopy (SEM) confirms 150 μm PSP had the best dispersion whereas 75 μm PSP resulted in agglomeration. PSP had little influence on the thermal stability of HDPE except for PHPC150 which showed an increase in the degradation temperature when compared to the virgin sample. Mechanical properties such as hardness, Young’s modulus, impact strength, and flexural modulus were enhanced by the addition of PSP. However, a decrease was noted in the elongation at break (%) and flexural strength of PHPC indicating the stiffening effect of the filler on the HDPE. In order to understand the particle size influence better, the extension evaluation method (EEM) was used for all samples and PHPC150 was found to be the best performing among all particle sizes.
- 1 October 2024
- Published by IOP Publishing in Materials Research Express
- Vol. 11 (10) , 105308
Open AccessInvestigating the influence of periwinkle shell powder on the thermal and mechanical performance of high-density polyethylene composites
In this study, the shell powder of Littorina littorea commonly called periwinkle was used as an eco-friendly filler in High-Density Polyethylene (HDPE) to form periwinkle/HDPE composites (PHPC). Understanding the effect of different particle sizes of periwinkle shell powder (PSP) and optimizing their influence on PHPC is the main scope of this work. Periwinkle shell (PS) particles with sizes ranging from L53, PHPC53, PHPC75, PHPC90, PHPC105, and PHPC150, respectively. The composites were fabricated by incorporating 1 wt% PSP into the HDPE matrix using the compression molding technique and then subjected to morphological, thermal, and mechanical characterizations. Morphology studies using scanning electron microscopy (SEM) confirms 150 μm PSP had the best dispersion whereas 75 μm PSP resulted in agglomeration. PSP had little influence on the thermal stability of HDPE except for PHPC150 which showed an increase in the degradation temperature when compared to the virgin sample. Mechanical properties such as hardness, Young’s modulus, impact strength, and flexural modulus were enhanced by the addition of PSP. However, a decrease was noted in the elongation at break (%) and flexural strength of PHPC indicating the stiffening effect of the filler on the HDPE. In order to understand the particle size influence better, the extension evaluation method (EEM) was used for all samples and PHPC150 was found to be the best performing among all particle sizes.
- 12 July 2023
- Published by SAGE Publications in Journal of Elastomers & Plastics
- Vol. 55 (6) , 896-916
A study on nitrile rubber/polyvinyl chloride blend vulcanization kinetics with different fillers by using single isothermal rheograph
An attempt has been made to establish a reasonably accurate microkinetics model for accelerated sulfur vulcanization of commonly used acrylonitrile rubber/polyvinyl chloride (NBR/PVC 70/30) blend (NVC73) from a single, isothermal rheograph data of torque versus time. The effect of three different types of fillers, such as pre-exfoliated organically modified montmorillonite (OMMT) clay, graphite (GRT) powder, and high abrasion furnace (HAF) carbon black (CB), were studied. The kinetics study was done with six solid-state reaction kinetics models. Among these, Sestak-Berggren (SB) equation was found to be the best model for the present compositions. The SB kinetic rate expressions were evolved after several iterations using empirical values of autocatalytic and non-autocatalytic orders of ‘ m’ and ‘ n’, respectively. The gum vulcanizate and OMMT clay-loaded compositions were found to have comparable conversion function f (α) and almost identical reaction rate constants at 150°C, under isothermal conditions. In comparison, HAF CB and GRT rate expressions differed from clay-loaded compositions. The validity of the reaction rate equations obtained was confirmed by comparison of plots for experimental and derived conversions with time.
- 12 July 2023
- Published by SAGE Publications in Journal of Elastomers & Plastics
- Vol. 55 (6) , 896-916
A study on nitrile rubber/polyvinyl chloride blend vulcanization kinetics with different fillers by using single isothermal rheograph
An attempt has been made to establish a reasonably accurate microkinetics model for accelerated sulfur vulcanization of commonly used acrylonitrile rubber/polyvinyl chloride (NBR/PVC 70/30) blend (NVC73) from a single, isothermal rheograph data of torque versus time. The effect of three different types of fillers, such as pre-exfoliated organically modified montmorillonite (OMMT) clay, graphite (GRT) powder, and high abrasion furnace (HAF) carbon black (CB), were studied. The kinetics study was done with six solid-state reaction kinetics models. Among these, Sestak-Berggren (SB) equation was found to be the best model for the present compositions. The SB kinetic rate expressions were evolved after several iterations using empirical values of autocatalytic and non-autocatalytic orders of ‘ m’ and ‘ n’, respectively. The gum vulcanizate and OMMT clay-loaded compositions were found to have comparable conversion function f (α) and almost identical reaction rate constants at 150°C, under isothermal conditions. In comparison, HAF CB and GRT rate expressions differed from clay-loaded compositions. The validity of the reaction rate equations obtained was confirmed by comparison of plots for experimental and derived conversions with time.
- Open Access
- 22 November 2021
- Published by Springer Nature in Research Square
Use of eco-benign periwinkle shell particle for making composites and study their effect on the thermal and mechanical properties of novel HDPE composites
In this investigation, the shell powder of Littorina littorea commonly called periwinkle was used as an eco-benign filler in High-Density Polyethylene (HDPE) to form periwinkle/HDPE composites (PHPC). Understanding the effect of different particle sizes of periwinkle shell powder (PSP) and optimizing their influence on PHPC is the main scope of work. Periwinkle shell (PS) particle sizes from <53 μm to 150 μm were chosen as reinforcement. The different PSP size like <53 μm, 53 μm, 75 μm, 90 μm, 105 μm and 150 μm chosen in this study were named as PHPCL53, PHPC53, PHPC75, PHPC90, PHPC105, and PHPC150 respectively. The composites were fabricated by incorporating 1 weight % of PSP into HDPE matrix using compression molding technique and then subjected to morphological, thermal, and mechanical characterizations. Morphology studies using scanning electron microscope (SEM) confirms 150 μm PSP had best dispersion whereas 75 μm PSP resulted with agglomeration. PSP had little influence on the thermal stability of HDPE except for PHPC150 which showed rise in degradation temperature when compared to the neat sample. Mechanical properties such as hardness, Young’s modulus, impact strength, and flexural modulus were enhanced by the addition of PSP. Whereas, a decrease was noted in elongation at break (%) and flexural strength of PHPC indicating the stiffening effect of filler on HDPE. In order to understand the particle size influence better, the extension evaluation method (EEM) was performed for all samples and PHPC150 was found to be the best performing among all particle sizes.
- 22 November 2021
- Published by Springer Nature in Research Square
Open AccessUse of eco-benign periwinkle shell particle for making composites and study their effect on the thermal and mechanical properties of novel HDPE composites
In this investigation, the shell powder of Littorina littorea commonly called periwinkle was used as an eco-benign filler in High-Density Polyethylene (HDPE) to form periwinkle/HDPE composites (PHPC). Understanding the effect of different particle sizes of periwinkle shell powder (PSP) and optimizing their influence on PHPC is the main scope of work. Periwinkle shell (PS) particle sizes from <53 μm to 150 μm were chosen as reinforcement. The different PSP size like <53 μm, 53 μm, 75 μm, 90 μm, 105 μm and 150 μm chosen in this study were named as PHPCL53, PHPC53, PHPC75, PHPC90, PHPC105, and PHPC150 respectively. The composites were fabricated by incorporating 1 weight % of PSP into HDPE matrix using compression molding technique and then subjected to morphological, thermal, and mechanical characterizations. Morphology studies using scanning electron microscope (SEM) confirms 150 μm PSP had best dispersion whereas 75 μm PSP resulted with agglomeration. PSP had little influence on the thermal stability of HDPE except for PHPC150 which showed rise in degradation temperature when compared to the neat sample. Mechanical properties such as hardness, Young’s modulus, impact strength, and flexural modulus were enhanced by the addition of PSP. Whereas, a decrease was noted in elongation at break (%) and flexural strength of PHPC indicating the stiffening effect of filler on HDPE. In order to understand the particle size influence better, the extension evaluation method (EEM) was performed for all samples and PHPC150 was found to be the best performing among all particle sizes.