BRBalachandran Surya Rajan

Balachandran Surya Rajan

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Balachandran Surya Rajan has a total of 48 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Investigating the influence of periwinkle shell powder on the thermal and mechanical performance of high-density polyethylene composites

    by Abbas Saifee Valsadwala, Sriram Srinivasan, Surya Rajan Balachandran, S Shamshath Begum, Asit Baran Samui, Sandeep Kumar Shukla

    In this study, the shell powder of Littorina littorea commonly called periwinkle was used as an eco-friendly filler in High-Density Polyethylene (HDPE) to form periwinkle/HDPE composites (PHPC). Understanding the effect of different particle sizes of periwinkle shell powder (PSP) and optimizing their influence on PHPC is the main scope of this work. Periwinkle shell (PS) particles with sizes ranging from L53, PHPC53, PHPC75, PHPC90, PHPC105, and PHPC150, respectively. The composites were fabricated by incorporating 1 wt% PSP into the HDPE matrix using the compression molding technique and then subjected to morphological, thermal, and mechanical characterizations. Morphology studies using scanning electron microscopy (SEM) confirms 150 μm PSP had the best dispersion whereas 75 μm PSP resulted in agglomeration. PSP had little influence on the thermal stability of HDPE except for PHPC150 which showed an increase in the degradation temperature when compared to the virgin sample. Mechanical properties such as hardness, Young’s modulus, impact strength, and flexural modulus were enhanced by the addition of PSP. However, a decrease was noted in the elongation at break (%) and flexural strength of PHPC indicating the stiffening effect of the filler on the HDPE. In order to understand the particle size influence better, the extension evaluation method (EEM) was used for all samples and PHPC150 was found to be the best performing among all particle sizes.


  • A comparative study of original equipment manufacturer brake pads using tribological testing and hybrid ranking for enhanced decision making and cost effectiveness

    by Parthasarathy Balaji, Balachandran Surya Rajan, Katharbasha Sathickbasha, Jitendra Kumar Katiyar, Paramathma Baskara Sethupathi, Kottur Asrar Ahmed

    Tribological test and hybrid ranking techniques are employed to evaluate brake pads from original equipment manufacturers for Indian passenger cars. The study was conducted for four brake pads designated as OE1, OE2, OE3, and OE4. The assessment integrates the analytical hierarchy process with various ranking methods including Extension Evaluation Method, Complex Proportional Assessment, Preference Selection Index, and Technique for Order of Preference by Similarity to Ideal Solution. Brake pad samples undergo testing according to the standard IS2742 part 1-4 of 1994, generating crucial performance parameters such as performance coefficient of friction, hot coefficient of friction, normal coefficient of friction, fade percentage, recovery percentage, variation in coefficient of friction, wear thickness loss percentage, wear mass loss percentage, and time taken to reach maximum temperature. These performance metrics are technically analyzed and ranked using hybrid ranking techniques to enhance the decision-making process. The results show that OE4, a budget-friendly brake pad ranked first, is the best performer. OE2, a more expensive alternative, is placed second, and OE1 and OE3, which are more affordable possibilities, are ranked third and fourth, respectively. This research serves as a valuable resource for selecting brake pads for Indian passenger cars, especially in scenarios where technical specifications and cost-effectiveness are crucial considerations.


  • Extraction of cellulose nanocrystals from red banana peduncle agro‐waste and application in environmentally friendly biocomposite film

    by Nagarajan K. J., Sanjay M. R., Sathick Basha K., Raghav G. R., Ashok Kumar R., Siengchin S., Surya Rajan B., Sabari Nath P., Anish Khan

    The agricultural waste dumped onto the land is creating an environmental problem. The conversion of those easily available agro‐wastes into value‐added nano reinforcement materials for biopolymers is an alternative method of waste utilization and minimization. In the current study, the red banana peduncle (RBP) waste was used as a precursor in the extraction of carboxylated cellulose nanocrystals (CCNCs) by alkalization, acidified chlorination citric acid hydrolysis, as well as the assessment of its reinforcing capability in polyvinyl alcohol. The characterization of the extracted CCNCs is analyzed through electron microscopy, X‐ray diffraction (XRD), Fourier transform infrared spectroscopy (FT‐IR), and Thermogravimetric analysis (TGA), respectively. The CCNCs exhibit a rod‐like shape (235 ± 20 nm length and 17.2 ± 6 nm width) with a high crystallinity of 89.7%, a negative zeta potential (−48 mV), and good thermal resistivity against degradation up to 280 °C. Furthermore, the effects of CCNCs integration on the bionanocomposite films' tensile, optical, bio decomposition, and thermal behavior were examined. The bionanocomposite film with improved physical, functional, thermal and bio decomposition characteristics offers the possibility for active packaging applications.


  • Synergistic effect of bismuth III sulfide and iron sulfide in the tribological performance of brake friction composite

    by Surya Rajan B, Sathickbasha K, Asrar Ahmed K, Hariharasakthisudhan P, Velmurugan C, Baskara Sethupathi P, Balaji P, Francesco Cotilli, K J Nagarajan

    Metal sulfides play a major role in determining the friction and wear performance of the brake friction composites. The usage of the combinations of metal sulfides improves tribological performance compared to its individual metal sulfides in the formulation of friction material. In this work, the effect of the Bismuth III sulfide and Iron disulfide combination was evaluated against the tribological performance in the formulation of the friction materials. Six brake friction pads were developed by properly balancing the weight percentage of Bismuth III sulfide and Iron disulfide in the formulation. The tribological performance of the friction liners was studied using a chase tribo-meter following the IS2742 test protocol. The worn surfaces of the brake pad samples were examined for its surface morphology and elemental behaviour using a Scanning electron microscope and an Energy-dispersive x-ray spectroscope. It was observed that the partial replacement of the Bismuth III sulfide with Iron sulfide improves the friction and fade performance. The abrasive nature of the Iron sulfide in the friction pad increases the coefficient of friction and causes the high wear loss beyond the ratio of 4:6 of the mixed sulfides. A statistical approach named preference selection Index was employed to rank the brake friction materials based on the multiple performance criteria.


  • Varying Cu and Zn composition in brass and its effect on the fade and recovery behavior of the phenolic‐based friction composites

    by Asrar Ahmed K, Rasool Mohideen S, Surya Rajan Balachandran, Sai Balaji M.A.

    Brass as a functional filler in the formulation of brake friction composites helps to improve the thermal conductivity, tribo‐load bearing ability, fade, recovery and wear resistance of the brake pads. The commercial brass alloy has 70 wt% copper and 30 wt% zinc. In this work, the tribological performance of the brass powders with 60 wt% Cu +40 wt% Zn and 80 wt% Cu +20 wt% Zn having similar morphology with the commercial brass was evaluated. The commercial and the two modified versions of brass filler were introduced in the formulation. Totally nine phenolic brake composite were formulated and fabricated by varying the brass filler types and their composition (6, 8 and 10 wt%) in the brake formulations. The tribological performance of the developed brake pads was studied using a chase‐type friction tester following IS 2742 test standard. The worn surface of the tested samples was studied using scanning electron microscopy and energy‐dispersive X‐ray spectroscopy. The tribological performance of the developed samples shows a nonlinear behavior concerning the variation in the composition. Therefore, statistical evaluation techniques such as hybrid analytical hierarchy process coupled with extension evaluation method (AHP‐EEM) and analytical hierarchy process coupled with Preference Selection Index (AHP‐PSI) were used to rank the developed samples based on the multiple tribological performance parameters. Based on the evaluation process the brake composite's composition with 8 wt% brass containing 70 wt% Cu and 30 wt% Zn has given the best overall performance.


  • Evaluation of mechanical properties of novel GLARE laminates filled with nanoclay

    by Hariharasakthisudhan Ponnarengan, Logesh Kamaraj, Surya Rajan Balachandran, Sathickbasha Kathar Basha

    In this research work, we have investigated the effect of nanoclay fillers in the epoxy adhesive on improving the interfacial adhesion and the mechanical properties of glass‐reinforced aluminum laminates. The laminates were prepared with a varying weight percentage of nanoclay fillers (i.e., 3, 4, and 5 wt%) in the epoxy resin using the hand lay‐up method. During the tensile test, the laminate's anisotropic nature was investigated using the samples cut in different orientations to the rolling direction (i.e., 0, 45, and 90°). The flexural, lap shear, and impact tests were conducted as per ASTM standards. After each test, the failure mechanisms of laminates were studied using the scanning electron microscope. The results showed that 3 wt% of nanoclay added in the epoxy enhanced the laminates' overall mechanical properties than other composites. The fiber metal laminates (FML) containing the nano clay more than 3 wt% showed deterioration in the mechanical property due to the improper distribution of nanoclay in the epoxy matrix. The FML's mechanical properties with nano clay filler were compared with other fillers' performance in the previous studies. It was found that the mechanical properties of FML with nano clay filler were more significant than others.


  • Top Cited Papers

    A comprehensive review on cellulose nanocrystals and cellulose nanofibers: Pretreatment, preparation, and characterization

    by K. J. Nagarajan, N. R. Ramanujam, M. R. Sanjay, Suchart. Siengchin, B. Surya Rajan, K. Sathick Basha, P. Madhu, G. R. Raghav

    Crafting ecological materials from green resources is posing a significant challenge for the researchers and scientists around the globe and has resulted in the development of nanocellulose materials, which has paved the way for enriching the basic knowledge and many opportunities on developing bio‐based materials. This has augmented the utilization of carbohydrate‐based organic materials and successfully replacing conventional nonrenewable materials. Cellulose nanomaterials (CNMs) belonging to the newer emerging field of nanomaterials are finding increasing interest among the investigators owing to their environmentally sustainable characteristics like biodegradability, biocompatibility, and potential availability in abundance at a cheaper price. The present review article intends to provide a detailed insight about the advancements and various challenges postured in the field of cellulose nanocrystals (CNCs) and cellulose nanofibers (CNFs). The article further discusses about different cellulose fiber extraction sources and their methods, purification processes employed, various sample preparation and drying techniques used for CNCs and CNFs. The article also outlines the various characterization methods practiced for scrutinizing CNCs and CNFs when used in polymer matrix composites. Finally, the benefits of using the CNMs in several potential applications such as paper, oil and gas industries, food packaging and structural sectors, conductive ink and water purification areas, medical and printed electronic fields are highlighted in this extensively reviewed article.


  • Effect of multi‐walled carbon nano‐tube on mechanical behavior of glass laminate aluminum reinforced epoxy composites

    by K. Logesh, P. Hariharasakthisudhan, B. Surya Rajan, A. Arul Marcel Moshi, V. Khalkar

    This research work is focused on development of epoxy based fiber metal laminate (FML) that comprised of multi‐walled carbon nano‐tube (MWCNT), glass fiber, and aluminum metal sheet. The hand layup technique was employed to fabricate the sandwich FML with different weight percentages (3, 4, and 5 wt%.) of MWCNT. The mechanical properties of the developed FMLs were determined through tensile, flexural, lap shear, and hardness tests following ASTM and IS standards. The scanning electron microscope (SEM) was used to characterize the failure mechanism of composites. The FML with MWCNT offered superior tensile and shear properties up to the addition of 4 wt%. The MWCNTs were found to be agglomerated in the epoxy when added more than 4 wt%. The FML's showed larger deformation before complete failure in shear mode with respect to the addition of MWCNTs. However, there was no considerable improvement recorded in the flexural and impact behavior of the FML composition. The addition of MWCNT fillers in the epoxy turned it more brittle and exhibited comparatively less deformation before failure in flexural mode.


  • Reusing exhausted alkaline battery powder as reinforcement in AA6061 composites and mechanical characterization

    by Hariharasakthisudhan Ponnarengan, Logesh Kamaraj, Surya Rajan Balachandran, Sathickbasha Kathar Basha

    One of the practical difficulties in replacing the conventional alloys with composite material is the cost of the synthetic reinforcement used in all types of composite materials. In the last two decades, several agricultural and industrial wastes were tried as reinforcement in polymer and metal matrix to enhance the mechanical and tribological properties of the composites. It is the need of the hour to develop the low-cost composites which can be achieved by reusing the commercial wastes as reinforcement in metal matrix materials. In this study, Aluminum alloy (AA6061) was used as matrix material. Alkaline battery powder after usage was reinforced in AA6061 matrix in different volume percentages (2, 4, 6, 8, and 12 vol %). The tensile properties of composite materials were evaluated using ASTM standards. The 6 vol % of used up alkaline battery powder in AA6061 improved the tensile properties after which a decrement in properties was observed. The porosity and agglomeration of reinforcement were noted as the prime reason for the decrement in properties. The ductile fracture was noticed in composites that possessed reinforcement volume of up to 6%. The combination of ductile and brittle was found in the composites with 8 and 12 vol % of reinforcement.


  • Open Access

    Inspiration of reinforcements, manufacturing methods, and microstructural changes on wear behavior of metal matrix composites—a recent review

    by P Hariharasakthisudhan, B Surya Rajan, K Sathickbasha

    The Metal Matrix Composites (MMCs) are increasingly replacing the commercial alloys in engineering components and undergoing intense analysis in the development of advanced composite structures. The metal matrix composites exhibit superior mechanical and tribological behavior than alloys in wear critical applications. Profound research works have been carried out in manufacturing the MMCs for improved friction and wear behavior. This study highlights the recent investigations from the perspective of wear behavior of MMCs. The effect of reinforcements and manufacturing processes of composites on wear behavior is elaborated. The significance of mechanical factors such as normal load, sliding speed and sliding distance is explained. The wear mechanisms observed in MMCs and studies on sub surface damages of composites are reported.