Nataliia Burdeina
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Nataliia Burdeina has a total of 66 co-authors. Here are the top co-authors by number of shared publications:
- Valentyn Glyva
Kyiv National University of Construction and Architecture
13 shared publications - Larysa Levchenko
National Technical University of Ukraine «Igor Sikorsky Kyiv Polytechnic Institute», Kyiv
12 shared publications - Yana Biruk
Kyiv National University of Construction and Architecture
11 shared publications - V. I. Nazarenko
State Institution "Kundiiev Institute of Occupational Health of the National Academy of Medical Sciences of Ukraine", Ukraine
7 shared publications - Kyrylo Nikolaiev
Interregional Academy of Personnel Management
6 shared publications - Oksana Tykhenko
National Aviation University
6 shared publications
Latest Publications
- Open Access
- 28 May 2026
- Published by Kyiv National University of Construction and Architecture in Strength of Materials and Theory of Structures
- No. 116
Theoretical and experimental bases for ensuring thermal and acoustic resistance of structural elements of buildings and shielding of electromagnetic radiation emission
An applied mathematical apparatus has been developed for predicting the thermal and acoustic resistance of building elements and the effectiveness of electromagnetic radiation shielding. Thermal resistance calculations take into account the influence of solar radiation and convective heat exchange on the outer surface of buildings. This makes it possible to rationalise the thermal protection of buildings and their energy efficiency. To predict the acoustic resistance of building structural elements, a multifactorial model of sound transmission through a protective layer has been improved, which has reduced the calculation error compared to known solutions. An applied calculation tool has been developed to predict the effectiveness of shielding electromagnetic radiation with building and facing materials. It is based on the relationships of electrodynamics of continuous media and is most suitable for multicomponent materials compared to semi-empirical formulas. Verification of the results obtained indicates an acceptable convergence of theoretical and experimental data. Given the presence of certain assumptions and simplifications in the calculations, in practical activities, a certain margin of effectiveness must be included in the protective properties of the designed materials and structures.
- 28 May 2026
- Published by Kyiv National University of Construction and Architecture in Strength of Materials and Theory of Structures
- No. 116
Open AccessTheoretical and experimental bases for ensuring thermal and acoustic resistance of structural elements of buildings and shielding of electromagnetic radiation emission
An applied mathematical apparatus has been developed for predicting the thermal and acoustic resistance of building elements and the effectiveness of electromagnetic radiation shielding. Thermal resistance calculations take into account the influence of solar radiation and convective heat exchange on the outer surface of buildings. This makes it possible to rationalise the thermal protection of buildings and their energy efficiency. To predict the acoustic resistance of building structural elements, a multifactorial model of sound transmission through a protective layer has been improved, which has reduced the calculation error compared to known solutions. An applied calculation tool has been developed to predict the effectiveness of shielding electromagnetic radiation with building and facing materials. It is based on the relationships of electrodynamics of continuous media and is most suitable for multicomponent materials compared to semi-empirical formulas. Verification of the results obtained indicates an acceptable convergence of theoretical and experimental data. Given the presence of certain assumptions and simplifications in the calculations, in practical activities, a certain margin of effectiveness must be included in the protective properties of the designed materials and structures.
- Open Access
- 30 October 2025
- Published by Kyiv National University of Construction and Architecture in Strength of Materials and Theory of Structures
- No. 115
Theoretical and experimental principles of designing sound insulation of buildings and structure
The principles of designing sound insulation of buildings and structures using materials of different physical characteristics are developed. The possibilities of simplifying sound insulation calculations for small values of the phase velocities of bending waves in the surface material are shown. It is shown that such a condition corresponds to small values of sound frequencies compared to the critical frequency of the surface. The limits of the acceptable error of calculations are determined, taking into account mainly resonant and inertial sound absorption. These limits roughly correspond to the sound frequencies f < 0,5fc, 0,5fc < f < 1,2fc and f > 1,2fc, fc being the critical surface frequency of these mass and dimensional parameters. The mathematical functions for calculating the sound insulation of surfaces made of soft materials are obtained. The values of the response functions of surfaces of different sizes are determined. It is shown that for frequencies above 300–400 Hz, the response function approaches unity and can be ignored. This conclusion is confirmed by experimental data, which have an acceptable agreement with the calculations. This greatly simplifies the practical design of soundproof structures. The principles of designing a two-layer structure to improve sound insulation are determined. It was found that sound insulation increases with an increase in the gap between the surfaces. However, at distances greater than 7-8·10-2 m, there is no increase in sound insulation, so an increase in the overall dimensions of soundproof structures is impractical.
- 30 October 2025
- Published by Kyiv National University of Construction and Architecture in Strength of Materials and Theory of Structures
- No. 115
Open AccessTheoretical and experimental principles of designing sound insulation of buildings and structure
The principles of designing sound insulation of buildings and structures using materials of different physical characteristics are developed. The possibilities of simplifying sound insulation calculations for small values of the phase velocities of bending waves in the surface material are shown. It is shown that such a condition corresponds to small values of sound frequencies compared to the critical frequency of the surface. The limits of the acceptable error of calculations are determined, taking into account mainly resonant and inertial sound absorption. These limits roughly correspond to the sound frequencies f < 0,5fc, 0,5fc < f < 1,2fc and f > 1,2fc, fc being the critical surface frequency of these mass and dimensional parameters. The mathematical functions for calculating the sound insulation of surfaces made of soft materials are obtained. The values of the response functions of surfaces of different sizes are determined. It is shown that for frequencies above 300–400 Hz, the response function approaches unity and can be ignored. This conclusion is confirmed by experimental data, which have an acceptable agreement with the calculations. This greatly simplifies the practical design of soundproof structures. The principles of designing a two-layer structure to improve sound insulation are determined. It was found that sound insulation increases with an increase in the gap between the surfaces. However, at distances greater than 7-8·10-2 m, there is no increase in sound insulation, so an increase in the overall dimensions of soundproof structures is impractical.
- Open Access
- 29 November 2024
- Published by Kyiv National University of Construction and Architecture in Strength of Materials and Theory of Structures
- No. 113,p. 329-336
Modelling the thermal resistance of layered structures for blocking infrared radiation
Ensuring high thermal resistance of building, cladding, finishing and other materials helps to solve the problems of energy efficiency of buildings and energy saving in general. Typically, building and cladding structures have several layers. This makes it difficult to predict their heat transfer. To solve these problems, it is proposed to model the thermal resistance of layered structures. The mathematical functions that should be used in modelling are determined. In particular, the mechanisms of heat transfer due to thermal conductivity and radiant heat transfer are separated. The assumptions and simplifications in the calculations that are acceptable in terms of errors are determined. The use of glass fibres for blocking infrared radiation is theoretically substantiated. The thermal resistance of a layered structure with an arbitrary number of layers and different thermal properties of each layer was modelled. The modelling was carried out using COMSOL tools. Changes in the thermal state of the layered structure in space and time were obtained. The modelling results were verified. Samples of materials based on glass fibre were manufactured and tested using a standard thermal imager. It was found that such a three-layer glass fibre material actually completely blocks infrared radiation at an initial temperature of up to 40 °С. Comparison of the results with the efficiency of a standard thermal insulation product shows that the predominant mechanism for blocking infrared radiation in a glass fibre-based product is the scattering of infrared radiation. This opens up the possibility of using glass fibre fabrics both to increase the thermal resistance of building and finishing materials and to produce infrared camouflage.
- 29 November 2024
- Published by Kyiv National University of Construction and Architecture in Strength of Materials and Theory of Structures
- No. 113,p. 329-336
Open AccessModelling the thermal resistance of layered structures for blocking infrared radiation
Ensuring high thermal resistance of building, cladding, finishing and other materials helps to solve the problems of energy efficiency of buildings and energy saving in general. Typically, building and cladding structures have several layers. This makes it difficult to predict their heat transfer. To solve these problems, it is proposed to model the thermal resistance of layered structures. The mathematical functions that should be used in modelling are determined. In particular, the mechanisms of heat transfer due to thermal conductivity and radiant heat transfer are separated. The assumptions and simplifications in the calculations that are acceptable in terms of errors are determined. The use of glass fibres for blocking infrared radiation is theoretically substantiated. The thermal resistance of a layered structure with an arbitrary number of layers and different thermal properties of each layer was modelled. The modelling was carried out using COMSOL tools. Changes in the thermal state of the layered structure in space and time were obtained. The modelling results were verified. Samples of materials based on glass fibre were manufactured and tested using a standard thermal imager. It was found that such a three-layer glass fibre material actually completely blocks infrared radiation at an initial temperature of up to 40 °С. Comparison of the results with the efficiency of a standard thermal insulation product shows that the predominant mechanism for blocking infrared radiation in a glass fibre-based product is the scattering of infrared radiation. This opens up the possibility of using glass fibre fabrics both to increase the thermal resistance of building and finishing materials and to produce infrared camouflage.
- 23 November 2024
- Published by Springer Nature
- p. 133-137
Composite Gradient Coatings Design for Ensuring Electromagnetic Compatibility of Onboard and Ground Electronic Equipment
- 23 November 2024
- Published by Springer Nature
- p. 133-137
Composite Gradient Coatings Design for Ensuring Electromagnetic Compatibility of Onboard and Ground Electronic Equipment
- Open Access
- 25 October 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 5 (10 (131)) , 45-52
Applying heterogeneous building materials for the protection of people against electromagnetic radiation
The object of this study is the processes of shielding electromagnetic radiation by building and facing materials. The research is aimed at solving the problem of ensuring the electromagnetic safety of people by improving the composition and structures of building and facing materials. Means for improving the electromagnetic safety of people under industrial and domestic conditions using non-homogeneous building materials have been determined. The shielding properties of reinforced concrete structures were studied. A methodology for increasing their efficiency depending on the amplitude-frequency characteristics of the radiation that needs shielding has been devised. The efficiency of electromagnetic radiation shielding by heterogeneous dielectric building materials based on cement concrete and basalt fibers was determined. It was established that shielding through the refraction of electromagnetic waves on inhomogeneities does not give an acceptable effect. The expediency of covering basalt fibers with a conductive substance to increase the protective properties of materials was substantiated. The protective properties of flat facing material with carbonyl iron content were studied. It has been shown that the properties of materials can be effectively controlled by adjusting the filler. The material's transmission coefficient of ultra-high frequency electromagnetic radiation does not exceed 0.40, and the reflection coefficient – 0.25 with a filler content in the base of 14–15 % by volume. This makes it possible to simultaneously ensure the electromagnetic safety of people and the stable functioning of wireless communication devices. The advantage of the material is the low coefficients of reflection of electromagnetic waves, which does not lead to deterioration of the electromagnetic situation in other areas where people stay. It has been established that the addition of boron nitride to the facing material significantly increases the thermal insulation characteristics of the coating and contributes to the solution of energy saving problems. Adding a layer containing boron nitride to the material provides thermal conductivity coefficients of 0.030–0.031 W/m·K, which is better than known analogs
- 25 October 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 5 (10 (131)) , 45-52
Open AccessApplying heterogeneous building materials for the protection of people against electromagnetic radiation
The object of this study is the processes of shielding electromagnetic radiation by building and facing materials. The research is aimed at solving the problem of ensuring the electromagnetic safety of people by improving the composition and structures of building and facing materials. Means for improving the electromagnetic safety of people under industrial and domestic conditions using non-homogeneous building materials have been determined. The shielding properties of reinforced concrete structures were studied. A methodology for increasing their efficiency depending on the amplitude-frequency characteristics of the radiation that needs shielding has been devised. The efficiency of electromagnetic radiation shielding by heterogeneous dielectric building materials based on cement concrete and basalt fibers was determined. It was established that shielding through the refraction of electromagnetic waves on inhomogeneities does not give an acceptable effect. The expediency of covering basalt fibers with a conductive substance to increase the protective properties of materials was substantiated. The protective properties of flat facing material with carbonyl iron content were studied. It has been shown that the properties of materials can be effectively controlled by adjusting the filler. The material's transmission coefficient of ultra-high frequency electromagnetic radiation does not exceed 0.40, and the reflection coefficient – 0.25 with a filler content in the base of 14–15 % by volume. This makes it possible to simultaneously ensure the electromagnetic safety of people and the stable functioning of wireless communication devices. The advantage of the material is the low coefficients of reflection of electromagnetic waves, which does not lead to deterioration of the electromagnetic situation in other areas where people stay. It has been established that the addition of boron nitride to the facing material significantly increases the thermal insulation characteristics of the coating and contributes to the solution of energy saving problems. Adding a layer containing boron nitride to the material provides thermal conductivity coefficients of 0.030–0.031 W/m·K, which is better than known analogs
- Open Access
- 27 September 2024
- Published by Kyiv National University of Construction and Architecture in Spatial development
- No. 9,p. 163-174
IMPROVEMENT OF THE METHODOLOGY FOR OBTAINING BASELINE DATA TO RATIONALISE THE EFFECTIVENESS OF SHIELDING PHYSICAL FIELDS
The shortcomings of the current regulatory framework for obtaining initial data for the design of materials and structures for shielding electromagnetic and acoustic fields are identified. It is shown that in order to obtain reliable data by the method of field measurements, it is necessary to be guided by the maximum basic error of the equipment. The calculations of the total electromagnetic field differ in the two existing acts on electromagnetic safety. They give different results, which complicates design work and forces the use of over-efficiency protection. It is necessary to harmonise national and international standards for determining the electromagnetic load on people. Currently, Ukraine lacks a metrological and methodological framework for determining the specific absorbed energy and specific absorbed power of an electromagnetic field. Only resonant structures are effective for protection against low-frequency sound and infrasound. To obtain information about the frequencies of maximum amplitudes that are selected as resonant, it is necessary to measure the previous vibration spectrum. But this is not provided for by the current standards.
- 27 September 2024
- Published by Kyiv National University of Construction and Architecture in Spatial development
- No. 9,p. 163-174
Open AccessIMPROVEMENT OF THE METHODOLOGY FOR OBTAINING BASELINE DATA TO RATIONALISE THE EFFECTIVENESS OF SHIELDING PHYSICAL FIELDS
The shortcomings of the current regulatory framework for obtaining initial data for the design of materials and structures for shielding electromagnetic and acoustic fields are identified. It is shown that in order to obtain reliable data by the method of field measurements, it is necessary to be guided by the maximum basic error of the equipment. The calculations of the total electromagnetic field differ in the two existing acts on electromagnetic safety. They give different results, which complicates design work and forces the use of over-efficiency protection. It is necessary to harmonise national and international standards for determining the electromagnetic load on people. Currently, Ukraine lacks a metrological and methodological framework for determining the specific absorbed energy and specific absorbed power of an electromagnetic field. Only resonant structures are effective for protection against low-frequency sound and infrasound. To obtain information about the frequencies of maximum amplitudes that are selected as resonant, it is necessary to measure the previous vibration spectrum. But this is not provided for by the current standards.
- Open Access
- 30 April 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 2 (10 (128)) , 26-33
Study of air deionization factors
The object of research is the dynamics in the concentration of air ions and suspended particles in atmospheric air and in supply-exhaust ventilation systems. An urgent task is to determine the factors and obtain quantitative data on the deionization of the atmospheric air that enters the environment where people live. Quantitative data on changes in the concentration of air ions depending on the time of day, temperature, and relative air humidity have been established. It was shown that even in the absence of significant man-made influence on the concentration of suspended particles, this indicator is at least 7000 cm-3. In the presence of wind, this indicator reaches 30000 cm-3 and higher. Measurement of the spectrum of suspended particles in the range of 0,3–6,0 μm showed that the predominant fraction is particles with sizes of about 3 μm. Studies have been conducted on changes in the concentrations of air ions in supply-exhaust ventilation systems. It was established that in the air duct made of galvanized iron, which has a length of 16 m, the concentration of negative air ions is reduced by 67 %, and positive by 78 %. Laboratory studies of air deionization in air ducts made of different materials were carried out. There is significant air deionization in metal and cardboard ducts while it is absent in wooden ducts. This indicates the electrical nature of deionization. A calculation method for forecasting the aero-ionic mode of premises, taking into account the factors of air deionization, is proposed. For rooms with supply-exhaust ventilation, a calculation apparatus is proposed taking into account the air exchange rate (the number of complete air changes per unit of time). The results make it possible to choose the required performance of artificial air ionization devices for normalizing the aero-ionic regimes in the premises
- 30 April 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 2 (10 (128)) , 26-33
Open AccessStudy of air deionization factors
The object of research is the dynamics in the concentration of air ions and suspended particles in atmospheric air and in supply-exhaust ventilation systems. An urgent task is to determine the factors and obtain quantitative data on the deionization of the atmospheric air that enters the environment where people live. Quantitative data on changes in the concentration of air ions depending on the time of day, temperature, and relative air humidity have been established. It was shown that even in the absence of significant man-made influence on the concentration of suspended particles, this indicator is at least 7000 cm-3. In the presence of wind, this indicator reaches 30000 cm-3 and higher. Measurement of the spectrum of suspended particles in the range of 0,3–6,0 μm showed that the predominant fraction is particles with sizes of about 3 μm. Studies have been conducted on changes in the concentrations of air ions in supply-exhaust ventilation systems. It was established that in the air duct made of galvanized iron, which has a length of 16 m, the concentration of negative air ions is reduced by 67 %, and positive by 78 %. Laboratory studies of air deionization in air ducts made of different materials were carried out. There is significant air deionization in metal and cardboard ducts while it is absent in wooden ducts. This indicates the electrical nature of deionization. A calculation method for forecasting the aero-ionic mode of premises, taking into account the factors of air deionization, is proposed. For rooms with supply-exhaust ventilation, a calculation apparatus is proposed taking into account the air exchange rate (the number of complete air changes per unit of time). The results make it possible to choose the required performance of artificial air ionization devices for normalizing the aero-ionic regimes in the premises
- Open Access
- 26 February 2024
- Published by National Technical University Kharkiv Polytechnic Institute in Advanced Information Systems
- Vol. 8 (1) , 24-30
MODELING OF THE EXTERNAL MAGNETIC FIELD OF ELECTRIC MACHINES
Powerful electric machines – such as electric generators, electric motors generate a magnetic field of great tension. These fields negatively effect on personnel and can to violate the stability of electronic equipment. To determine safe areas for workers, laying communication cables and placing sensitive electronic equipment, it is advisable to model the propagation of magnetic fields of electrical machines. This will make it possible to rationalize the placing of electrical equipment at design stages. The most common high-power electrical machines are four-pole electrical machines with a dipole-quadrupole structure of the external magnetic field. The purpose of the research is a development of models of the propagation of the external magnetic field generated by alternating current electric machines. Results of the research: it is substantiated that to simulate the propagation of the magnetic field of electric machines, it is advisable to use the Gauss equation for the magnetic scalar potential. This will make it possible to take into account the required number of spatial harmonics of the magnetic field to ensure an acceptable calculation error. An electric machine is considered in a spherical approximation. Calculations were carried out in spherical coordinates. The distances were determined in relative radii of the electric machine - the ratio of the radius of the machine to the definition of field strength. The calculations were made for two planes of spherical coordinates and a three-dimensional image was obtained. As a result of the simulation, it is possible to determine the magnetic field strength of a four-pole electric machine at selected distances and directions around the electric machine with the required accuracy. It has been established that there are points of zero external magnetic field strength around electrical machines. Verification of the simulation results was carried out using the method of full-scale measurements of the magnetic field strength around a real four-pole machine. The measurement results showed acceptable agreement with the calculated data. Conclusions: the chosen approach and the results of modeling the propagation of the external magnetic field of electrical machines can be used to design the placement of electrical equipment, taking into account the requirements for electromagnetic safety and electromagnetic compatibility of technical equipment.
- 26 February 2024
- Published by National Technical University Kharkiv Polytechnic Institute in Advanced Information Systems
- Vol. 8 (1) , 24-30
Open AccessMODELING OF THE EXTERNAL MAGNETIC FIELD OF ELECTRIC MACHINES
Powerful electric machines – such as electric generators, electric motors generate a magnetic field of great tension. These fields negatively effect on personnel and can to violate the stability of electronic equipment. To determine safe areas for workers, laying communication cables and placing sensitive electronic equipment, it is advisable to model the propagation of magnetic fields of electrical machines. This will make it possible to rationalize the placing of electrical equipment at design stages. The most common high-power electrical machines are four-pole electrical machines with a dipole-quadrupole structure of the external magnetic field. The purpose of the research is a development of models of the propagation of the external magnetic field generated by alternating current electric machines. Results of the research: it is substantiated that to simulate the propagation of the magnetic field of electric machines, it is advisable to use the Gauss equation for the magnetic scalar potential. This will make it possible to take into account the required number of spatial harmonics of the magnetic field to ensure an acceptable calculation error. An electric machine is considered in a spherical approximation. Calculations were carried out in spherical coordinates. The distances were determined in relative radii of the electric machine - the ratio of the radius of the machine to the definition of field strength. The calculations were made for two planes of spherical coordinates and a three-dimensional image was obtained. As a result of the simulation, it is possible to determine the magnetic field strength of a four-pole electric machine at selected distances and directions around the electric machine with the required accuracy. It has been established that there are points of zero external magnetic field strength around electrical machines. Verification of the simulation results was carried out using the method of full-scale measurements of the magnetic field strength around a real four-pole machine. The measurement results showed acceptable agreement with the calculated data. Conclusions: the chosen approach and the results of modeling the propagation of the external magnetic field of electrical machines can be used to design the placement of electrical equipment, taking into account the requirements for electromagnetic safety and electromagnetic compatibility of technical equipment.
- 25 December 2023
- Published by Kundiiev Institute of Occupational Health of National Academy of Medical Sciences of Ukraine in Ukrainian Journal of Occupational Health
- Vol. 2023 (4) , 285-293
Light pulsation coefficient in workplaces with visual means of displaying information and ways of its normalization
Light pulsation coefficient in workplaces with visual means of displaying information and ways of its normalization: ISSN 2223-6775 Ukrainian journal of occupational health Vol.19, No 4, 2023https://doi.org/10.33573/ujoh2023.04 Light pulsation coefficient in workplaces with visual means of displaying information and ways of its normalization Nazarenko V.I.1, Glyva V.A.2
- 25 December 2023
- Published by Kundiiev Institute of Occupational Health of National Academy of Medical Sciences of Ukraine in Ukrainian Journal of Occupational Health
- Vol. 2023 (4) , 285-293
Light pulsation coefficient in workplaces with visual means of displaying information and ways of its normalization
Light pulsation coefficient in workplaces with visual means of displaying information and ways of its normalization: ISSN 2223-6775 Ukrainian journal of occupational health Vol.19, No 4, 2023https://doi.org/10.33573/ujoh2023.04 Light pulsation coefficient in workplaces with visual means of displaying information and ways of its normalization Nazarenko V.I.1, Glyva V.A.2
- Open Access
- 31 August 2023
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 4 (10 (124)) , 6-14
Identifying regularities in the propagation of air ions in rooms with artificial air ionization
The object of the study is the dynamics of air ion spread in rooms from the source of artificial air ionization under different starting conditions. There is currently the problem of distribution of air ions in the room with regulatory concentrations in all critical zones. An effective method of ensuring proper air ion concentrations is to model their propagation from ionization sources. Existing approaches to calculating the dynamics of air ions of both polarities have been improved in this study. Unlike known solutions, the impact on their concentration of electrostatic field and the interaction of air ions with suspended particles was taken into account. A model of air ion propagation in rooms with artificial air ionization and the principles of its numerical modeling was built. The use of Laplace Equation in the aerodynamic model instead of the Navier-Stokes equation for the potential of the flow rate has made it possible to design an "Ion 3D" tool, which reduces the time of implementation of one scenario from several hours to 7 seconds. Modeling of the propagation of air ions of both polarities in the room under different initial conditions was carried out. Two-dimensional and three-dimensional models with their visualization was implemented. The peculiarity of the resulting models is that they make it possible to determine the concentrations of air ions in any section of the room by three coordinates. Given this, the rapid selection of the variants of the source data makes it possible to achieve the normative values of concentrations of air ions in the area of breathing – exceeding 500 cm-3 of each polarity. Simulation makes it possible to design a room in which, under the condition of artificial ionization of air, the concentrations of air ions close to the optimal values of 3000–5000 cm-3 are provided
- 31 August 2023
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 4 (10 (124)) , 6-14
Open AccessIdentifying regularities in the propagation of air ions in rooms with artificial air ionization
The object of the study is the dynamics of air ion spread in rooms from the source of artificial air ionization under different starting conditions. There is currently the problem of distribution of air ions in the room with regulatory concentrations in all critical zones. An effective method of ensuring proper air ion concentrations is to model their propagation from ionization sources. Existing approaches to calculating the dynamics of air ions of both polarities have been improved in this study. Unlike known solutions, the impact on their concentration of electrostatic field and the interaction of air ions with suspended particles was taken into account. A model of air ion propagation in rooms with artificial air ionization and the principles of its numerical modeling was built. The use of Laplace Equation in the aerodynamic model instead of the Navier-Stokes equation for the potential of the flow rate has made it possible to design an "Ion 3D" tool, which reduces the time of implementation of one scenario from several hours to 7 seconds. Modeling of the propagation of air ions of both polarities in the room under different initial conditions was carried out. Two-dimensional and three-dimensional models with their visualization was implemented. The peculiarity of the resulting models is that they make it possible to determine the concentrations of air ions in any section of the room by three coordinates. Given this, the rapid selection of the variants of the source data makes it possible to achieve the normative values of concentrations of air ions in the area of breathing – exceeding 500 cm-3 of each polarity. Simulation makes it possible to design a room in which, under the condition of artificial ionization of air, the concentrations of air ions close to the optimal values of 3000–5000 cm-3 are provided