MFMichelângelo Vargas Fassarella

Michelângelo Vargas Fassarella

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Michelângelo Vargas Fassarella has a total of 28 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Characterization of Hedychium coronarium fiber and evaluation of its reinforcement in epoxy resin

    by Michelangelo Vargas Fassarella, Mateus Urbano Do Nascimento, Emilly Soares Gomes Silva, Fabricio Gomes Gonçalves, Laiza Andrade Lauriano, Caroline Palacio de Araujo, Michel Picanço Oliveira

    The replacement of synthetic fibers with lignocellulosic reinforcements has gained increasing attention due to their low cost, renewability, and environmental benefits. In this context, Hedychium coronarium (wild ginger), an invasive species with high biomass yield, was investigated as a novel fiber source for epoxy composites. Leaf sheath fibers (FLHC) were characterized for chemical composition, crystallinity (73.23%), crystallite size (2.56 nm), morphology, and tensile strength (196.6 MPa). Epoxy composites reinforced with 10, 20, and 30 wt% FLHC were evaluated through mechanical testing, thermal analysis (TGA/DTG), FTIR spectroscopy, and scanning electron microscopy. Fiber incorporation progressively enhanced tensile strength (59.98 MPa at 30 wt% loading), increased the elastic modulus by up to 250%, and tripled impact resistance, although limited fiber–matrix adhesion constrained further improvements in toughness. This study is novel in demonstrating, for the first time, that FLHC can function as a high‑quality reinforcement in epoxy composites, reducing demand for synthetic resins and valorising biomass from an invasive species.

  • Open Access

    Influence of Wood Chemical Composition on Liquefaction Efficiency and Polyurethane Foam Properties: A Study of Red Angico and Mahogany

    by Emilly Silva, Luísa Cruz-Lopes, Idalina Domingos, Fabricio Gonçalves, Bruna da Silva Cruz, Michelângelo Fassarella, Antônio Thiago de Almeida, Bruno Esteves

    Biomass liquefaction is a thermochemical process that converts lignocellulosic materials into reactive liquid intermediates, enabling the production of bio-based polyols as a sustainable alternative to petroleum-derived chemicals. This study investigates the liquefaction of two lignocellulosic biomasses, Red Angico (Anadenanthera colubrina) and Mahogany (Swietenia macrophylla), using a glycerol–ethylene glycol polyalcohol system, chosen for its renewable origin and high solvating efficiency. The resulting polyols were used to produce polyurethane (PU) foams, and their properties were evaluated in relation to biomass composition. The chemical composition of each biomass significantly influenced its liquefaction behavior and polyol characteristics. Mahogany achieved higher liquefaction efficiency, whereas Red Angico polyols generated PU foams with superior mechanical performance, highlighting the influence of species-specific chemistry. Water content and isocyanate index were found to modulate foam structure and compressive strength. This work demonstrates how tailored liquefaction strategies using polyalcohol systems can optimize bio-based PU foam properties, providing a sustainable route for high-performance polymer materials.


  • Statistical strategies for decision-making regarding the quality of particleboards with glass wool

    by Michelângelo V. Fassarella, Izabella Luzia S. Chaves, Juarez B. Paes, Roberto Carlos C. Lelis, Geovanna S. Polvarini, Udson O. Barros Junior, Fabricio G. Gonçalves

    This study evaluated multivariate statistical strategies to select critical properties for the performance of particleboards bonded with urea-formaldehyde (UF) adhesive modified with glass wool residues. Panels were produced with six different proportions of glass wool incorporated into the UF adhesive (0%, 3.34%, 4.93%, 6.52%, 9.49%, 12.35%). These panels were characterized by physical, mechanical, fire-retardant, and acoustic properties. Three statistical tools were applied: hierarchical cluster analysis, principal component analysis (PCA), and Pearson correlation. PCA explained 80.3% of the total variance, revealing distinct patterns among treatments, especially at the lowest and highest filler contents. The correlation matrix showed the interdependence between the rheological properties of the adhesive and the final composite performance. Glass wool as a filling material, in the proportion of 3.34% of the adhesive, provided the best performance among the panels, as it promoted balance between mechanical, physical and acoustic properties. Up to the limit of 6.52% glass wool contributed to improving fire resistance without significant changes in mechanical strength but reduced dimensional stability due to changes in adhesive rheology. The combination of multivariate analyses provided a robust approach to identify key attributes and guide the formulation of panels with enhanced technical and functional performance.

  • Open Access

    Influence of Wood Chemical Composition on Liquefaction Efficiency and Polyurethane Foam Properties: A Study of Red Angico and Mahogany

    by Emilly Soares Gomes Silva, Luísa Cruz-Lopes, Idalina Domingos, Fabricio Gonçalves, Bruna da Silva Cruz, Michelângelo Vargas Fassarella, Antônio Thiago de Almeida, Bruno Esteves

    This study investigates the chemical composition, liquefaction behavior, and polyurethane foam (PU) properties of two lignocellulosic biomasses, Red Angico (Anadenanthera colubrina) and Mahogany (Swietenia macrophylla), as potential sources of bio-based polyols. Detailed chemical characterization revealed that Red Angico has high α-cellulose (48.44%) and moderate hemicellulose (25.68%) content, while Mahogany shows the inverse, with high hemicellulose (56.11%) and low cellulose (18.24%), influencing their reactivity during liquefaction. Liquefaction trials using a polyalcohol system (glycerol:ethylene glycol) demonstrated higher conversion efficiency for Mahogany, reaching 93.4% at 180 °C in 60 minutes, compared to 73.9% for Red Angico. Hydroxyl value analysis revealed increasing functionality for Mahogany polyols with time, whereas Red Angico showed declining values, indicating possible recondensation reactions. PU foams were synthesized using the resulting polyols, with compressive strength and modulus increasing with isocyanate index. Red Angico foams, despite lower OH values, displayed superior mechanical performance, attributed to their lower hydroxyl content favoring optimal crosslinking. Water content, used as a chemical blowing agent, negatively impacted compressive strength for both foams due to increased porosity. Results highlight the species-specific influence of chemical composition on liquefaction behavior and foam performance, suggesting tailored processing conditions are essential for maximizing bio-based PU properties.

  • Open Access

    Chemical Modification of Pachira aquatica Oil for Bio-Based Polyurethane Wood Adhesives

    by Emilly Silva, Bruno Esteves, Idalina Domingos, Margarida Almeida, Bruno Araújo, Izabella Chaves, Michelângelo Fassarella, Roberto Lelis, Juarez Paes, Luísa Carvalho, et al.

    The development of biomass-based adhesives has attracted interest as an alternative to petroleum-derived synthetic and potentially toxic adhesives. Pachira aquatica oil is a renewable raw material that can be incorporated into an MDI-based polyurethane system. In this study, the chemical composition and reactivity of P. aquatica oil were characterized using GC–MS, FTIR, and hydroxyl index measurements. The oil showed a predominance of saturated fatty acids, particularly methyl hexadecanoate (64.80%), derived from palmitic acid, and exhibited a low initial hydroxyl value. To enhance reactivity, the oil was transesterified with glycerol under different conditions, producing polyols with substantially increased hydroxyl values (412–769 mg KOH g−1), as confirmed by the intensified O–H and C–O bands in the FTIR spectra. The polyurethane adhesives were formulated from the selected polyols (P3 and P4) and evaluated at different NCO/OH ratios and pressing temperatures, using ABES shear tests. The highest ABES shear strength recorded was approximately 3.6 MPa, obtained for isocyanate indices between 0.8 and 1.0 and temperatures around 115 °C. Although this value represents the best performance among the tested conditions, it remains below the industrial benchmarks typically associated with the EN 205 standard (≈10 MPa). It is important to note that the ABES and EN 205 methods are not directly comparable due to differences in testing protocols. Nevertheless, the results indicate that, under the evaluated conditions, the adhesives exhibit limited mechanical performance and require further optimization.


  • Open Access

    The Potential for Glass Wool Waste as a Filler in UF Adhesive to Promote Particleboard Strength

    by Michelângelo Vargas Fassarella, Izabella Luzia Silva Chaves, Pedro Gutemberg Alcântara Segundinho, Juarez Benigno Paes, Roberto Carlos Costa Lelis, Michel Picanço Oliveira, Emilly Soares Gomes Silva, Fabricio Gomes Gonçalves

    Wastes, biomasses, and nanoparticles have motivated reformulations of adhesives in the wood-based-panel industry. This study investigated the incorporation of glass wool (GW) waste as a filler material in urea–formaldehyde (UF) adhesive, evaluating its effects on the adhesive properties as well as on the physical, mechanical, fire-retardant, and acoustic properties of particleboards. Panels with a target density of 700 kg m−3 were produced with different proportions of glass wool in the adhesive (T1: 0%; T2: 3.34%; T3: 4.93%; T4: 6.52%; T5: 9.49%; T6: 12.35%). The adhesive-coated particle mat was pressed in a hydraulic press at 160 °C under a compression force of 72 tons for 10 min. The panels were subjected to analyses of their physical, mechanical, fire-retardant, and acoustic properties, as well as scanning electron microscopy (SEM) analyses. Statistical analysis involved regression, analysis of variance, and a Scott–Knott test (p < 0.05). The results indicated that adding 3.34% GW to the adhesive improved the modulus of rupture, internal bond strength, screw withdrawal resistance, and acoustic efficiency of the panels. A glass wool content of 12.35% enhanced the hardness and the damping factor. These findings highlight the potential of glass wool as a functional filler material in UF adhesive, promoting the development of stronger and more sustainable particleboards.


  • Open Access

    Physical and Mechanical Properties of Juvenile Wood of Anadenanthera peregrina (L.) Speg. from Thinning

    by Emilly Soares Gomes Silva, Fabricio Gomes Gonçalves, Pedro Gutemberg Alcântara Segundinho, Cleyton Machado Prata Filho, Yonny Martinez Lopez, Izabella Luzia Silva Chaves, Donatian Gustave, Michelângelo Vargas Fassarella, Bruno Miguel Morais Lemos Esteves

    Reducing the rotation period through thinning and changing planting spacing can influence the technological properties of wood, with little attention paid to the effects of these variables on the raw material, which limits its processing in the wood sector. This work aimed to evaluate the physical and mechanical properties of wood from Anadenanthera peregrina juveniles thinned in three planting spacings (3 m × 3 m, 4 m × 4 m, and 5 m × 5 m). The physical properties in the base-top and pith–shell directions and the mechanical properties of the samples were evaluated. The results indicate better technological properties for wood with larger spacings. The physical properties showed decreasing trends in the base-top direction and increasing trends in the pith-bark direction, with a distinct trend in the degree of collapse. The average basic density of the different planting spacings varied between 0.47 g cm−3 and 0.63 g cm−3. The mechanical properties obtained for the 4 m × 4 m spacing were superior to those of the other spacings. Wood from young A. peregrina is an alternative for industrial processing, as wood from higher planting densities is more suitable for purposes that require resistance and rigidity.


  • Open Access

    Extracción de taninos de la corteza de Pinus spp tratada térmicamente – aplicación como adhesivo

    by Fabricio Gomes Gonçalves, Izabella Luzia Silva Chaves, Michelângelo Vargas Fassarella, Alice Soares Brito, Émilly Soares Gomes da Silva, Yonny Martinez López, Rafael Espósito Gonçalves de Oliveira

    Se identificó la influencia del tratamiento térmico en la obtención de compuestos tánicos condensables a partir de residuos de corteza de Pinus spp para la producción de adhesivo. Los tratamientos térmicos fueron: (a) corteza sin tratamiento térmico (testigo); (b) corteza expuesta a 60 °C durante 50 h en seco; (c) corteza expuesta a 120 °C durante 10 h en vapor; (d) corteza adherida al tronco expuesta a 120 °C durante 10 h en vapor. Para su caracterización química, la corteza fue molida y clasificada. Se extrajeron los compuestos tánicos mediante reflujo con agua destilada durante 2 h; se adicionaron sales de carbonato de sodio y sulfito de sodio, ambos a 5% en relación con la masa seca. Para el testigo fueron evaluadas las propiedades del tanino comercial de Acacia mearnsii (acacia negra). El proceso de extracción de taninos fue realizado en autoclave y se evaluaron las siguientes propiedades: viscosidad, pH, tiempo de formación de gel, contenido de sólidos y densidad. Tanto la corteza expuesta a 120 °C durante 10 horas en vapor como la adherida al tronco sometida a 120 °C a vapor durante 10 h, para ambas sales, exhibieron los mayores rendimientos de taninos. Los extractos tánicos obtenidos a partir de carbonato de sodio presentaron una estructura alcalina, alta viscosidad y menor tiempo de formación de gel. Sin embargo, los extractos obtenidos a partir de sulfito de sodio proporcionaron un carácter ácido y contenido de sólidos próximos a los encontrados en los extractos tánicos acuosos obtenido de la acacia negra.


  • Open Access

    Relação entre propriedades elásticas e biológicas em painéis aglomerados feitos com resíduos de madeira de eucalipto

    by Fabricio Gomes Gonçalves, Pedro Gutemberg de Alcântara Segundinho, Michelângelo Vargas Fassarella, Daniela Minini, Vinícius Peixoto Tinti, Yonny Martinez Lopez, Mayária Josiânia Kercília Firmes Sampaio Felberg

    RESUMO Neste trabalho obteve-se corpos de prova provenientes de painéis aglomerados confeccionados a partir de resíduos de madeira serrada de eucalipto. Caracterizou-se o módulo de elasticidade a partir da frequência flexional e longitudinal e módulo de cisalhamento por meio de ensaios não destrutivo e destrutivo. Foram avaliadas a resistência biológica dos painéis a partir da reação aos fungos Neolentinus lepideus e Brunneoporus malicola (≈ Gloeopyllum trabeum) e com térmitas Cryptotermes brevis e Nasutitermes sp. Nestes ensaios determinou-se a perda de massa após o período de ataque. Observou-se relação entre o método de vibração flexional do corpo de prova retangular com o módulo de elasticidade estático, possibilitando o uso desse método. Os painéis com menor teor de tanino (2%) no adesivo apresentaram desempenhos mecânicos inferiores. As técnicas utilizadas mostraram ser possível a estimação das propriedades em painéis aglomerados. Os painéis apresentaram-se mais resistentes para o fungo B. malicola com as menores perdas de massa (média geral de 15,73%) em relação ao N. lepideus (45,73%). Os painéis confeccionados com 100 % de tanino-formaldeído promoveram maior perda de massa quando em contato com a térmita Cryptotermes brevis (12,54%) e para ambos os fungos B. malicola (21,2%) e N. lepideus (53,8%). Para as térmitas Nasutitermes sp. os painéis com 100% de tanino foram menos degradados.