Praveen Kumar
Research Subjects
Praveen Kumar has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Gayathri Pillai
Centre for Nano Science and Engineering, Indian Institute of Science, Bengaluru, India
3 shared publications - Mandar M. Inamdar
Department of Civil Engineering, Indian Institute of Technology Bombay, Mumbai 400076, India
3 shared publications - Antony Jeyaseelan
Materials Science Division, CSIR-National Aerospace Laboratories, Bangalore—560017, India
2 shared publications - Dnyanesh N. Pawaskar
Department of Mechanical Engineering, Indian Institute of Technology Bombay, Mumbai, India
2 shared publications M. M. Nayak
Indian Institute of Science
2 shared publications- Rudra Pratap
Centre for Nano Science and Engineering, Indian Institute of Science, Bangalore, 560012, India
2 shared publications
Latest Publications
- Open Access
- 15 October 2026
- Published by Springer Nature in Research Square
Overcoming Material Trade-Offs in MEMS Transducers via Lateral Ferroelectric–Piezoelectric Thin-film Integration
Piezoelectric microelectromechanical systems (MEMS) transducers are constrained by a fundamental materials trade-off. Materials that enable strong electromechanical actuation typically exhibit high dielectric permittivity and loss and in contrast, materials optimized for electrical sensing generally provide weaker piezoelectric coupling. Here, we overcome this limitation through the first extensive experimental demonstration of a laterally integrated ferroelectric–piezoelectric resonator architecture designed to enhance transceiver efficiency and figure of merit (FoM). Lead Zirconate Titanate (PZT) and Aluminum Nitride (AlN) are integrated with equal area coverage within the same resonator plane. In this configuration, the high piezoelectric coefficient of PZT enables efficient electromechanical actuation, while the low permittivity and dielectric loss of AlN enable high-voltage sensing. The second resonant mode is used to directly compare actuation and sensing performance under identical strain conditions. This allows material-dependent transduction effects to be isolated. Experimental results demonstrate an approximately 10× increase in electrical output voltage when PZT is used for actuation and AlN for sensing, compared with the reverse configuration. This enhancement is observed across devices spanning frequencies from the kHz to MHz range and results in a substantial improvement in FoM. The architecture also enables DC-bias tunability and enhanced performance through ferroelectric poling of PZT while preserving low-loss AlN sensing. These results establish lateral material integration as an effective strategy for combining complementary ferroelectric and piezoelectric functionalities within a single MEMS resonator for sensing, signal processing, and ultrasonic applications.
- 15 October 2026
- Published by Springer Nature in Research Square
Open AccessOvercoming Material Trade-Offs in MEMS Transducers via Lateral Ferroelectric–Piezoelectric Thin-film Integration
Piezoelectric microelectromechanical systems (MEMS) transducers are constrained by a fundamental materials trade-off. Materials that enable strong electromechanical actuation typically exhibit high dielectric permittivity and loss and in contrast, materials optimized for electrical sensing generally provide weaker piezoelectric coupling. Here, we overcome this limitation through the first extensive experimental demonstration of a laterally integrated ferroelectric–piezoelectric resonator architecture designed to enhance transceiver efficiency and figure of merit (FoM). Lead Zirconate Titanate (PZT) and Aluminum Nitride (AlN) are integrated with equal area coverage within the same resonator plane. In this configuration, the high piezoelectric coefficient of PZT enables efficient electromechanical actuation, while the low permittivity and dielectric loss of AlN enable high-voltage sensing. The second resonant mode is used to directly compare actuation and sensing performance under identical strain conditions. This allows material-dependent transduction effects to be isolated. Experimental results demonstrate an approximately 10× increase in electrical output voltage when PZT is used for actuation and AlN for sensing, compared with the reverse configuration. This enhancement is observed across devices spanning frequencies from the kHz to MHz range and results in a substantial improvement in FoM. The architecture also enables DC-bias tunability and enhanced performance through ferroelectric poling of PZT while preserving low-loss AlN sensing. These results establish lateral material integration as an effective strategy for combining complementary ferroelectric and piezoelectric functionalities within a single MEMS resonator for sensing, signal processing, and ultrasonic applications.
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (20) , 30450-30462
Multimode Resonant Pressure Sensor With High Sensitivity and Wide Operating Range
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (20) , 30450-30462
Multimode Resonant Pressure Sensor With High Sensitivity and Wide Operating Range
- Open Access
- 12 September 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 138 (10)
Tunable phononic frequency combs in curved piezoelectric micromachined ultrasound transducers enabled by 2:1 internal resonance and a ferroelectric thin film
Phononic frequency combs have been demonstrated in various MEMS resonators through intermodal coupling, analogous to their optical counterparts. This work presents the generation of tunable frequency combs through nonlinear intermodal coupling based on 2:1 internal resonance and a ferroelectric thin film in curved circular piezoelectric micromachined ultrasound transducers (PMUTs). Our experiments reveal strong 2:1 resonance coupling between the first asymmetric and second symmetric modes of the circular PMUT and its critical role in comb evolution. Notably, robust comb behavior with varying comb spacing is observed at both coupled modes as a function of applied DC voltage, AC actuation voltage, and single-tone drive frequency. We provide a theoretical dynamical model that explains the experimental results and highlights the role of modal coupling via 2:1 internal resonance in comb generation. Our findings underscore the significance of resonance coupling and input parameters in generating and tuning phononic frequency combs, paving the way for advancements in nonlinear phononics.
- 12 September 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 138 (10)
Open AccessTunable phononic frequency combs in curved piezoelectric micromachined ultrasound transducers enabled by 2:1 internal resonance and a ferroelectric thin film
Phononic frequency combs have been demonstrated in various MEMS resonators through intermodal coupling, analogous to their optical counterparts. This work presents the generation of tunable frequency combs through nonlinear intermodal coupling based on 2:1 internal resonance and a ferroelectric thin film in curved circular piezoelectric micromachined ultrasound transducers (PMUTs). Our experiments reveal strong 2:1 resonance coupling between the first asymmetric and second symmetric modes of the circular PMUT and its critical role in comb evolution. Notably, robust comb behavior with varying comb spacing is observed at both coupled modes as a function of applied DC voltage, AC actuation voltage, and single-tone drive frequency. We provide a theoretical dynamical model that explains the experimental results and highlights the role of modal coupling via 2:1 internal resonance in comb generation. Our findings underscore the significance of resonance coupling and input parameters in generating and tuning phononic frequency combs, paving the way for advancements in nonlinear phononics.
- 29 October 2024
- Published by ASME International in Journal of Computational and Nonlinear Dynamics
- Vol. 19 (12) , 1-11
Characterization of Three-Mode Combination Internal Resonances in Electrostatically Actuated Flexible–Flexible Microbeams
Nonlinear intermodal coupling based on internal resonances in MEMS resonators has advanced significantly over the past two decades for various real-world applications. In this study, we demonstrate the existence of various three-mode combination internal resonances between the first five flexural modes of electrostatically actuated flexible-flexible beams and dynamic modal interaction between three modes via internal resonance. We first calculate the natural frequencies of the beam as a function of the stiffnesses of the transverse and rotational springs of the flexible supports, utilizing both analytical formulation and finite element analysis. Following this, we identify six combination internal resonances among the first five modes and use applied DC voltage to validate the exactness of one commensurable internal resonance condition (ω2=ω5-ω4). Subsequently, we studied a detailed forced vibration analysis corresponding to this resonance condition by solving the five-mode coupled governing equations through numerical time integration and the method of multiple scales. The results compellingly exhibit three-mode intermodal coupling among the second, fourth, and fifth modes as a function of excitation amplitude and frequency. Alongside this, intriguing nonlinear phenomena such as threshold behavior, saturation phenomena, and auto-parametric instability are observed. Finally, this paper provides a systematic methodology for investigating three-mode combination internal resonances and related nonlinear dynamics, offering significant insights that could be used in observing phonon or mechanical lasing phenomena in MEMS resonators.
- 29 October 2024
- Published by ASME International in Journal of Computational and Nonlinear Dynamics
- Vol. 19 (12) , 1-11
Characterization of Three-Mode Combination Internal Resonances in Electrostatically Actuated Flexible–Flexible Microbeams
Nonlinear intermodal coupling based on internal resonances in MEMS resonators has advanced significantly over the past two decades for various real-world applications. In this study, we demonstrate the existence of various three-mode combination internal resonances between the first five flexural modes of electrostatically actuated flexible-flexible beams and dynamic modal interaction between three modes via internal resonance. We first calculate the natural frequencies of the beam as a function of the stiffnesses of the transverse and rotational springs of the flexible supports, utilizing both analytical formulation and finite element analysis. Following this, we identify six combination internal resonances among the first five modes and use applied DC voltage to validate the exactness of one commensurable internal resonance condition (ω2=ω5-ω4). Subsequently, we studied a detailed forced vibration analysis corresponding to this resonance condition by solving the five-mode coupled governing equations through numerical time integration and the method of multiple scales. The results compellingly exhibit three-mode intermodal coupling among the second, fourth, and fifth modes as a function of excitation amplitude and frequency. Alongside this, intriguing nonlinear phenomena such as threshold behavior, saturation phenomena, and auto-parametric instability are observed. Finally, this paper provides a systematic methodology for investigating three-mode combination internal resonances and related nonlinear dynamics, offering significant insights that could be used in observing phonon or mechanical lasing phenomena in MEMS resonators.
- 7 December 2023
- Published by Springer Nature in International Journal of Dynamics and Control
- Vol. 12 (7) , 2128-2143
Mass sensing based on nonlinear intermodal coupling via 2:1 internal resonance of electrostatically actuated clamped–clamped microbeams
- 7 December 2023
- Published by Springer Nature in International Journal of Dynamics and Control
- Vol. 12 (7) , 2128-2143
Mass sensing based on nonlinear intermodal coupling via 2:1 internal resonance of electrostatically actuated clamped–clamped microbeams
- 19 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Letters
- Vol. 7 (12) , 1-4
Ultrasensitive Pressure Sensor Based on an Integrated Circular Piezoelectric MEMS Resonator and Diaphragm Structure
In this letter, we report an ultrasensitive pressure sensor based on an integrated circular piezoelectric microelectromechanical resonator and stainless-steel diaphragm structure. Finite element analysis is conducted to validate the working principle of the sensor, identify modes with high-pressure sensitivity and estimate the resonance frequency drift. The sensor operates on the principle of frequency shift caused by the coupling between the applied pressure and stress of the resonator. The high electromechanical coupling coefficient of Lead Zirconate Titanate facilitates seamless transduction between the physical domains of interest. The sensitivity of the sensor is 31, 711 ppm/bar and 14, 600 ppm/bar for the first and second flexural modes with nonlinearity of 2.2% full-scale (FS) and 0.84%FS, respectively, in the operating range of 0-5 bar at room temperature. The sensor exhibits excellent repeatability for multiple bidirectional pressure sweep. The proof of concept demonstrated in this letter will enable miniaturization and batch fabrication of pressure sensors with high sensitivity and bandwidth of operation.
- 19 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Letters
- Vol. 7 (12) , 1-4
Ultrasensitive Pressure Sensor Based on an Integrated Circular Piezoelectric MEMS Resonator and Diaphragm Structure
In this letter, we report an ultrasensitive pressure sensor based on an integrated circular piezoelectric microelectromechanical resonator and stainless-steel diaphragm structure. Finite element analysis is conducted to validate the working principle of the sensor, identify modes with high-pressure sensitivity and estimate the resonance frequency drift. The sensor operates on the principle of frequency shift caused by the coupling between the applied pressure and stress of the resonator. The high electromechanical coupling coefficient of Lead Zirconate Titanate facilitates seamless transduction between the physical domains of interest. The sensitivity of the sensor is 31, 711 ppm/bar and 14, 600 ppm/bar for the first and second flexural modes with nonlinearity of 2.2% full-scale (FS) and 0.84%FS, respectively, in the operating range of 0-5 bar at room temperature. The sensor exhibits excellent repeatability for multiple bidirectional pressure sweep. The proof of concept demonstrated in this letter will enable miniaturization and batch fabrication of pressure sensors with high sensitivity and bandwidth of operation.
- 3 August 2023
- Published by Springer Nature in Journal of Vibration Engineering & Technologies
- Vol. 12 (3) , 3783-3796
Investigation of a Bandpass Filter Based on Nonlinear Modal Coupling via 2:1 Internal Resonance of Electrostatically Actuated Clamped-Guided Microbeams
- 3 August 2023
- Published by Springer Nature in Journal of Vibration Engineering & Technologies
- Vol. 12 (3) , 3783-3796
Investigation of a Bandpass Filter Based on Nonlinear Modal Coupling via 2:1 Internal Resonance of Electrostatically Actuated Clamped-Guided Microbeams
- 13 August 2021
- Published by Springer Nature in Meccanica
- Vol. 57 (1) , 143-163
Investigating internal resonances and 3:1 modal interaction in an electrostatically actuated clamped-hinged microbeam
- 13 August 2021
- Published by Springer Nature in Meccanica
- Vol. 57 (1) , 143-163
Investigating internal resonances and 3:1 modal interaction in an electrostatically actuated clamped-hinged microbeam
- 1 January 2013
- Published by Inderscience Publishers in International Journal of Structural Engineering
- Vol. 4 (3) , 234
Response of piping system with semi-active variable friction dampers under tri-directional seismic excitation
Seismic loads on piping system due to earthquakes can cause excessive vibrations, which can lead to serious instability resulting in damage or complete failure. In this paper, semi-active variable friction dampers (SAVFDs) have been studied to mitigate seismic response and vibration control of piping system used in the process industries, fossil and fissile fuel power plant. A study is also conducted on the performance of control due to variation in gain multiplier (α) in the present control law, which plays an important role in the present control algorithm of the damper. The effectiveness of the SAVFD in terms of reduction in the responses, namely, displacements, accelerations and base shear of the piping system is investigated by comparing uncontrolled responses under four artificial earthquake motions with increasing amplitudes. The analytical results demonstrate that the SAVFDs under particular optimum parameters are very effective and practically implementable for the seismic response mitigation, vibration control and seismic requalification of piping systems.
- 1 January 2013
- Published by Inderscience Publishers in International Journal of Structural Engineering
- Vol. 4 (3) , 234
Response of piping system with semi-active variable friction dampers under tri-directional seismic excitation
Seismic loads on piping system due to earthquakes can cause excessive vibrations, which can lead to serious instability resulting in damage or complete failure. In this paper, semi-active variable friction dampers (SAVFDs) have been studied to mitigate seismic response and vibration control of piping system used in the process industries, fossil and fissile fuel power plant. A study is also conducted on the performance of control due to variation in gain multiplier (α) in the present control law, which plays an important role in the present control algorithm of the damper. The effectiveness of the SAVFD in terms of reduction in the responses, namely, displacements, accelerations and base shear of the piping system is investigated by comparing uncontrolled responses under four artificial earthquake motions with increasing amplitudes. The analytical results demonstrate that the SAVFDs under particular optimum parameters are very effective and practically implementable for the seismic response mitigation, vibration control and seismic requalification of piping systems.