Gayathri Pillai
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Gayathri Pillai has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
Antony Jeyaseelan
Indian Institute of Science
3 shared publications- Praveen Kumar
Indian Institute of Science
3 shared publications - Rudra Pratap
Centre for Nano Science and Engineering, Indian Institute of Science, Bangalore, 560012, India
3 shared publications - Antony Jeyaseelan
Materials Science Division, CSIR-National Aerospace Laboratories, Bangalore—560017, India
2 shared publications - Kongbrailatpam Sandeep Sharma
Center for Nano Science and Engineering, Indian Institute of Science at Bengaluru, Bengaluru, India
2 shared publications M. M. Nayak
Indian Institute of Science
2 shared publications
Latest Publications
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (20) , 30450-30462
Multimode Resonant Pressure Sensor With High Sensitivity and Wide Operating Range
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (20) , 30450-30462
Multimode Resonant Pressure Sensor With High Sensitivity and Wide Operating Range
- 1 January 2026
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 8 (1) , 125-133
Surface Engineering of Ti–Pt Bottom Electrodes for Precise Texture Control of PZT Thin Films on Si
- 1 January 2026
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 8 (1) , 125-133
Surface Engineering of Ti–Pt Bottom Electrodes for Precise Texture Control of PZT Thin Films on Si
- Open Access
- 17 November 2025
- Published by Springer Nature in Microsystems & Nanoengineering
- Vol. 11 (1) , 217
Switchable and tuneable high-performance acoustic modes in the L-X band using ferroelectric thin film on sapphire
High overtone bulk acoustic resonators (HBAR) are advantageous for on-chip quantum acoustodynamics (QAD) system as it gives access to stream of phonon modes with high lifetime in the microwave frequency range while retaining low power consumption and microscale footprint. In this paper we present a HBAR based on barium strontium titanate (BST) thin-film mounted on sapphire with modes exhibiting frequency quality factor product (fQ) of 1.72 × 1015 Hz which is the highest reported for a bulk acoustic wave resonator utilizing polycrystalline ferroelectric material as a means for acoustic wave excitation. Unlike other piezoelectric based HBARs, the DC field-induced piezoelectricity utilized in this work offers multiple on-chip tuneability of resonator’s dynamic parameters such as phonon lifetime, frequency modulation and coupling. The higher overtone feature can enable qubit(s) in a hybrid quantum circuit to interact with one or more acoustic modes to form a quantum transducer. Here, the multi-mode resonator exhibits a unique DC bias dependency, and this feature of the ferroelectric thin film adds control variables that efficiently tune static and dynamic material, mechanical and electrical properties of the device. The resonator records a loaded quality factor of 180,000 in X band and 140,000 in the L band when measured at 10 K. A controllable robust resonator with simple fabrication technique offering high fQ can be a strong platform to be used in QAD circuits for applications in metrology, quantum memory and quantum information processing.
- 17 November 2025
- Published by Springer Nature in Microsystems & Nanoengineering
- Vol. 11 (1) , 217
Open AccessSwitchable and tuneable high-performance acoustic modes in the L-X band using ferroelectric thin film on sapphire
High overtone bulk acoustic resonators (HBAR) are advantageous for on-chip quantum acoustodynamics (QAD) system as it gives access to stream of phonon modes with high lifetime in the microwave frequency range while retaining low power consumption and microscale footprint. In this paper we present a HBAR based on barium strontium titanate (BST) thin-film mounted on sapphire with modes exhibiting frequency quality factor product (fQ) of 1.72 × 1015 Hz which is the highest reported for a bulk acoustic wave resonator utilizing polycrystalline ferroelectric material as a means for acoustic wave excitation. Unlike other piezoelectric based HBARs, the DC field-induced piezoelectricity utilized in this work offers multiple on-chip tuneability of resonator’s dynamic parameters such as phonon lifetime, frequency modulation and coupling. The higher overtone feature can enable qubit(s) in a hybrid quantum circuit to interact with one or more acoustic modes to form a quantum transducer. Here, the multi-mode resonator exhibits a unique DC bias dependency, and this feature of the ferroelectric thin film adds control variables that efficiently tune static and dynamic material, mechanical and electrical properties of the device. The resonator records a loaded quality factor of 180,000 in X band and 140,000 in the L band when measured at 10 K. A controllable robust resonator with simple fabrication technique offering high fQ can be a strong platform to be used in QAD circuits for applications in metrology, quantum memory and quantum information processing.
- Open Access
- 12 September 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 138 (10)
Tunable phononic frequency combs in curved piezoelectric micromachined ultrasound transducers enabled by 2:1 internal resonance and a ferroelectric thin film
Phononic frequency combs have been demonstrated in various MEMS resonators through intermodal coupling, analogous to their optical counterparts. This work presents the generation of tunable frequency combs through nonlinear intermodal coupling based on 2:1 internal resonance and a ferroelectric thin film in curved circular piezoelectric micromachined ultrasound transducers (PMUTs). Our experiments reveal strong 2:1 resonance coupling between the first asymmetric and second symmetric modes of the circular PMUT and its critical role in comb evolution. Notably, robust comb behavior with varying comb spacing is observed at both coupled modes as a function of applied DC voltage, AC actuation voltage, and single-tone drive frequency. We provide a theoretical dynamical model that explains the experimental results and highlights the role of modal coupling via 2:1 internal resonance in comb generation. Our findings underscore the significance of resonance coupling and input parameters in generating and tuning phononic frequency combs, paving the way for advancements in nonlinear phononics.
- 12 September 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 138 (10)
Open AccessTunable phononic frequency combs in curved piezoelectric micromachined ultrasound transducers enabled by 2:1 internal resonance and a ferroelectric thin film
Phononic frequency combs have been demonstrated in various MEMS resonators through intermodal coupling, analogous to their optical counterparts. This work presents the generation of tunable frequency combs through nonlinear intermodal coupling based on 2:1 internal resonance and a ferroelectric thin film in curved circular piezoelectric micromachined ultrasound transducers (PMUTs). Our experiments reveal strong 2:1 resonance coupling between the first asymmetric and second symmetric modes of the circular PMUT and its critical role in comb evolution. Notably, robust comb behavior with varying comb spacing is observed at both coupled modes as a function of applied DC voltage, AC actuation voltage, and single-tone drive frequency. We provide a theoretical dynamical model that explains the experimental results and highlights the role of modal coupling via 2:1 internal resonance in comb generation. Our findings underscore the significance of resonance coupling and input parameters in generating and tuning phononic frequency combs, paving the way for advancements in nonlinear phononics.
- Open Access
- 8 May 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 1-12
Evolution of tunable phononic frequency combs via three-mode interaction in curved piezoelectric micromachined ultrasonic transducers
Phononic frequency combs are the mechanical counterparts of optical frequency combs, representing a pivotal progression in nonlinear studies of micro-electromechanical systems. This work presents the generation of tunable frequency combs based on three-mode interaction through combination internal resonance and a ferroelectric thin film in curved piezoelectric micromachined ultrasonic transducer. The experimental results demonstrate rich three-mode coupled nonlinear dynamics and how this coupling leads to frequency comb generation under specific input actuation parameters. The comb spacing and the number of spectral lines can be tuned by modulating the applied DC voltage, as well as the AC input voltage and frequency. Unlike previous studies on three-mode comb analysis, a theoretical model is systematically developed using nonlinear von Kármán plate theory to elucidate the experimentally observed dynamics of nonlinear three-mode intermodal coupling through combination internal resonance and its role in comb generation. Our findings demonstrate resonance coupling between the first and third asymmetric modes and the second symmetric modes, underscoring the generation of tunable multimode phononic frequency combs. This advancement paves the way for further progress in nonlinear phononics, enabling diverse applications in sensors, acoustic imaging, and phonon computation.
- 8 May 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 1-12
Open AccessEvolution of tunable phononic frequency combs via three-mode interaction in curved piezoelectric micromachined ultrasonic transducers
Phononic frequency combs are the mechanical counterparts of optical frequency combs, representing a pivotal progression in nonlinear studies of micro-electromechanical systems. This work presents the generation of tunable frequency combs based on three-mode interaction through combination internal resonance and a ferroelectric thin film in curved piezoelectric micromachined ultrasonic transducer. The experimental results demonstrate rich three-mode coupled nonlinear dynamics and how this coupling leads to frequency comb generation under specific input actuation parameters. The comb spacing and the number of spectral lines can be tuned by modulating the applied DC voltage, as well as the AC input voltage and frequency. Unlike previous studies on three-mode comb analysis, a theoretical model is systematically developed using nonlinear von Kármán plate theory to elucidate the experimentally observed dynamics of nonlinear three-mode intermodal coupling through combination internal resonance and its role in comb generation. Our findings demonstrate resonance coupling between the first and third asymmetric modes and the second symmetric modes, underscoring the generation of tunable multimode phononic frequency combs. This advancement paves the way for further progress in nonlinear phononics, enabling diverse applications in sensors, acoustic imaging, and phonon computation.
- 21 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
- Vol. 72 (1) , 55-63
Cryogenic Characterization of Low-Loss Thin-Film Lithium Niobate on Sapphire Shear Horizontal Surface Acoustic Wave Devices
This paper reports a cryogenic study on wideband shear horizontal surface acoustic wave (SH-SAW) devices based on an emerging Y-cut LiNbO 3 /SiO 2 /Sapphire (LNOS) platform. To perform a comprehensive study, low-loss acoustic delay lines (ADLs) equipped with unidirectional transducers were designed with a wavelength (λ) of 4 μm (900 MHz) and a wide fractional bandwidth (FBW) of around 7%, featuring various physical delays ranging from 5λ to 200λ as testing structures. By cooling the temperature down to 5 K, the insertion loss (IL) of the longest ADL and the extracted propagation loss (PL) were characterized as 4.1 dB and 3.5 dB/mm, respectively. Compared with an IL of 5.78 dB and a PL of 4.37 dB/mm at 275 K, the temperature-dependent acoustic losses diminish at low temperatures, with the overall PL dominated by the acoustic waveguide formed by the acoustic velocity mismatch between layers. Furthermore, a one-port resonator (λ = 2.8 μm) with a large perceived effective electromechanical coupling greater than 40% was also characterized using the same technique, showing a 2X boost in the maximum Bode-Q at cryogenic temperatures. This study not only characterized the acoustic properties of wideband LNOS SH-SAW devices but also validated their excellent performance across a wide temperature range, suggesting their potential applications in cryogenic phononic circuits.
- 21 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
- Vol. 72 (1) , 55-63
Cryogenic Characterization of Low-Loss Thin-Film Lithium Niobate on Sapphire Shear Horizontal Surface Acoustic Wave Devices
This paper reports a cryogenic study on wideband shear horizontal surface acoustic wave (SH-SAW) devices based on an emerging Y-cut LiNbO 3 /SiO 2 /Sapphire (LNOS) platform. To perform a comprehensive study, low-loss acoustic delay lines (ADLs) equipped with unidirectional transducers were designed with a wavelength (λ) of 4 μm (900 MHz) and a wide fractional bandwidth (FBW) of around 7%, featuring various physical delays ranging from 5λ to 200λ as testing structures. By cooling the temperature down to 5 K, the insertion loss (IL) of the longest ADL and the extracted propagation loss (PL) were characterized as 4.1 dB and 3.5 dB/mm, respectively. Compared with an IL of 5.78 dB and a PL of 4.37 dB/mm at 275 K, the temperature-dependent acoustic losses diminish at low temperatures, with the overall PL dominated by the acoustic waveguide formed by the acoustic velocity mismatch between layers. Furthermore, a one-port resonator (λ = 2.8 μm) with a large perceived effective electromechanical coupling greater than 40% was also characterized using the same technique, showing a 2X boost in the maximum Bode-Q at cryogenic temperatures. This study not only characterized the acoustic properties of wideband LNOS SH-SAW devices but also validated their excellent performance across a wide temperature range, suggesting their potential applications in cryogenic phononic circuits.
- 4 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Microelectromechanical Systems
- Vol. 33 (6) , 793-805
Synchronized Opto-Electro-Mechanical Measurements for Estimation of Energy Dissipation in Thin-Film-Piezoelectricon-Substrate MEMS/NEMS Devices
Piezoelectric microelectromechanical systems have significant market potential owing to their superior capabilities of transduction to those of standard capacitive and piezoresistive devices. However, piezoelectric films are often lossy, which reduces the Quality Factor of devices and affects their performance. It is thus important to examine all sources of energy dissipation in such devices and accurately determine them based on experimental data. Currently used methods to quantify energy dissipation from different sources and the properties of materials based on experimental data are set-up for piezoelectric devices, in which energy storage and dissipation primarily occur in the same piezoelectric material. Moreover, such methods rely on resonance-antiresonance measurements, and thus are unsuitable for thin-film-piezoelectric-on-substrate (TPoS) Micro/Nano devices that have i) a significant portion of energy stored in the substrate/device layer, ii) a low signal-to-noise ratio owing to either lossy piezoelectric films or high motional impedance, or iii) a larger feedthrough capacitance, arising primarily from collocated electrodes, in addition to the internal capacitance of the piezoelectric film. In this paper, we propose a method that overcomes these challenges based on synchronized optical and electrical measurements. We develop a comprehensive physics-based model to extract all the relevant parameters for the device, including the coefficient of piezoelectric coupling, internal and feedthrough capacitance, loss tangents (dielectric, piezoelectric, and mechanical), and the contributions of different sources to the Quality Factor of the device. We showcase the proposed method by using a PZT-based TPoS MEMS cantilever and a Piezoelectric Micromachined Ultrasonic Transducers (PMUT). 2024-0063
- 4 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Microelectromechanical Systems
- Vol. 33 (6) , 793-805
Synchronized Opto-Electro-Mechanical Measurements for Estimation of Energy Dissipation in Thin-Film-Piezoelectricon-Substrate MEMS/NEMS Devices
Piezoelectric microelectromechanical systems have significant market potential owing to their superior capabilities of transduction to those of standard capacitive and piezoresistive devices. However, piezoelectric films are often lossy, which reduces the Quality Factor of devices and affects their performance. It is thus important to examine all sources of energy dissipation in such devices and accurately determine them based on experimental data. Currently used methods to quantify energy dissipation from different sources and the properties of materials based on experimental data are set-up for piezoelectric devices, in which energy storage and dissipation primarily occur in the same piezoelectric material. Moreover, such methods rely on resonance-antiresonance measurements, and thus are unsuitable for thin-film-piezoelectric-on-substrate (TPoS) Micro/Nano devices that have i) a significant portion of energy stored in the substrate/device layer, ii) a low signal-to-noise ratio owing to either lossy piezoelectric films or high motional impedance, or iii) a larger feedthrough capacitance, arising primarily from collocated electrodes, in addition to the internal capacitance of the piezoelectric film. In this paper, we propose a method that overcomes these challenges based on synchronized optical and electrical measurements. We develop a comprehensive physics-based model to extract all the relevant parameters for the device, including the coefficient of piezoelectric coupling, internal and feedthrough capacitance, loss tangents (dielectric, piezoelectric, and mechanical), and the contributions of different sources to the Quality Factor of the device. We showcase the proposed method by using a PZT-based TPoS MEMS cantilever and a Piezoelectric Micromachined Ultrasonic Transducers (PMUT). 2024-0063
- 19 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Letters
- Vol. 7 (12) , 1-4
Ultrasensitive Pressure Sensor Based on an Integrated Circular Piezoelectric MEMS Resonator and Diaphragm Structure
In this letter, we report an ultrasensitive pressure sensor based on an integrated circular piezoelectric microelectromechanical resonator and stainless-steel diaphragm structure. Finite element analysis is conducted to validate the working principle of the sensor, identify modes with high-pressure sensitivity and estimate the resonance frequency drift. The sensor operates on the principle of frequency shift caused by the coupling between the applied pressure and stress of the resonator. The high electromechanical coupling coefficient of Lead Zirconate Titanate facilitates seamless transduction between the physical domains of interest. The sensitivity of the sensor is 31, 711 ppm/bar and 14, 600 ppm/bar for the first and second flexural modes with nonlinearity of 2.2% full-scale (FS) and 0.84%FS, respectively, in the operating range of 0-5 bar at room temperature. The sensor exhibits excellent repeatability for multiple bidirectional pressure sweep. The proof of concept demonstrated in this letter will enable miniaturization and batch fabrication of pressure sensors with high sensitivity and bandwidth of operation.
- 19 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Letters
- Vol. 7 (12) , 1-4
Ultrasensitive Pressure Sensor Based on an Integrated Circular Piezoelectric MEMS Resonator and Diaphragm Structure
In this letter, we report an ultrasensitive pressure sensor based on an integrated circular piezoelectric microelectromechanical resonator and stainless-steel diaphragm structure. Finite element analysis is conducted to validate the working principle of the sensor, identify modes with high-pressure sensitivity and estimate the resonance frequency drift. The sensor operates on the principle of frequency shift caused by the coupling between the applied pressure and stress of the resonator. The high electromechanical coupling coefficient of Lead Zirconate Titanate facilitates seamless transduction between the physical domains of interest. The sensitivity of the sensor is 31, 711 ppm/bar and 14, 600 ppm/bar for the first and second flexural modes with nonlinearity of 2.2% full-scale (FS) and 0.84%FS, respectively, in the operating range of 0-5 bar at room temperature. The sensor exhibits excellent repeatability for multiple bidirectional pressure sweep. The proof of concept demonstrated in this letter will enable miniaturization and batch fabrication of pressure sensors with high sensitivity and bandwidth of operation.
- 13 July 2022
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 32 (8) , 084004
Investigation of support transducer enabled higher-order radial bulk mode MEMS resonator and low phase noise oscillator
This work reports the successful excitation of a novel bulk acoustic mode whose actuation and sensing are facilitated by the support transducer topology (STT). The design methodology concurrently supports low motional impedance and high energy confinement features which are crucial for frequency reference components in Radio Frequency communication. A conventional bulk mode operating in the width extension (WE) mode is deployed to efficiently excite the higher-order radial mode using the STT design feature of resonant frequency matching. The thin-film piezoelectric on substrate support transducers excited in a WE mode is mechanically coupled to the bulk silicon allowing the acoustic energy of the MEMS resonator to be stored maximally in the high-quality factor ( Q ) resonant tank, thereby alleviating the overall losses due to low- Q of the piezoelectric thin film and electrode material. The resonator exhibits a Q of 19 728 at 63.56 MHz resonant frequency with a motional resistance ( R m ) of 368 Ω when measured in vacuum at a power level of 0 dBm. Under cryogenic measurement conditions, the device recorded a Q of 24 153 at 15 K. A standalone WE resonator is studied to put a spotlight on the quality factor enhancement technique using the STT. The STT enabled novel bulk mode enhances the overall Q by 320% and halves the R m . When implemented as an oscillator, its performance exceeds the Global System for Mobile communication standards phase noise (PN) requirements. PN of −136.95 dBc Hz −1 and −161.52 dBc Hz −1 at 1 kHz and 1 MHz offset, respectively, were recorded when normalized to a carrier frequency of 13 MHz.
- 13 July 2022
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 32 (8) , 084004
Investigation of support transducer enabled higher-order radial bulk mode MEMS resonator and low phase noise oscillator
This work reports the successful excitation of a novel bulk acoustic mode whose actuation and sensing are facilitated by the support transducer topology (STT). The design methodology concurrently supports low motional impedance and high energy confinement features which are crucial for frequency reference components in Radio Frequency communication. A conventional bulk mode operating in the width extension (WE) mode is deployed to efficiently excite the higher-order radial mode using the STT design feature of resonant frequency matching. The thin-film piezoelectric on substrate support transducers excited in a WE mode is mechanically coupled to the bulk silicon allowing the acoustic energy of the MEMS resonator to be stored maximally in the high-quality factor ( Q ) resonant tank, thereby alleviating the overall losses due to low- Q of the piezoelectric thin film and electrode material. The resonator exhibits a Q of 19 728 at 63.56 MHz resonant frequency with a motional resistance ( R m ) of 368 Ω when measured in vacuum at a power level of 0 dBm. Under cryogenic measurement conditions, the device recorded a Q of 24 153 at 15 K. A standalone WE resonator is studied to put a spotlight on the quality factor enhancement technique using the STT. The STT enabled novel bulk mode enhances the overall Q by 320% and halves the R m . When implemented as an oscillator, its performance exceeds the Global System for Mobile communication standards phase noise (PN) requirements. PN of −136.95 dBc Hz −1 and −161.52 dBc Hz −1 at 1 kHz and 1 MHz offset, respectively, were recorded when normalized to a carrier frequency of 13 MHz.