Lei Lu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Lei Lu has a total of 60 co-authors. Here are the top co-authors by number of shared publications:
- Haijun Liu
School of Mechanical Engineering, Hefei University of Technology, Hefei, China
8 shared publications Jiang Han
School of Mechanical Engineering, Hefei University of Technology, Hefei, China
8 shared publicationsShan Chen
School of Mechanical Engineering, Hefei University of Technology, Hefei, China
6 shared publicationsLining Sun
Soochow University
5 shared publicationsLei Zhang
Soochow University
4 shared publications- Xiaoqing Tian
School of Mechanical Engineering, Hefei University of Technology, Hefei, China
4 shared publications
Latest Publications
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE/ASME Transactions on Mechatronics
- Vol. 31 (5) , 5582-5592
A Tool Posture Path Optimization Method for Robot-Turntable Surface Milling Process Based on 7-DOF Constant Tool-Tip-Stiffness
Robot-Turntable, with advantages such as extensive workspace, excellent flexibility, is gradually playing an important role in manufacturing process, especially suitable for large rotating parts such as propellers, impellers, etc. While providing sufficient degrees of freedom, thereby allowing greater flexibility in trajectory optimization, it also increases the difficulty of trajectory planning in joint-space. Moreover, insufficient stiffness further limits the widespread application of industrial robots in high-intensity machining. In response to this issue, this article proposes a tool posture path optimization method for 7-DOF robot-turntable milling process based on constant end-stiffness index of robot-turntable configuration machining equipment. First, the stiffness performance index of 7-DOF robot-turntable configuration machining equipment are established, and the stiffness performance index is introduced into the robot-turntable. Taking into account other constraints such as the dexterity index of 7-DOF robot-turntable, the tool posture path optimization model based on constant stiffness performance index is then established. Finally, four sets of trajectory machining experiments and two sets of metal surface machining experiments are conducted on the 7-DOF robot-turntable configuration machining equipment. The analysis of experimental data indicate that the joint trajectory planned using the constant stiffness index effectively reduces the robot’s vibration displacement during machining, thereby decreasing surface roughness.
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE/ASME Transactions on Mechatronics
- Vol. 31 (5) , 5582-5592
A Tool Posture Path Optimization Method for Robot-Turntable Surface Milling Process Based on 7-DOF Constant Tool-Tip-Stiffness
Robot-Turntable, with advantages such as extensive workspace, excellent flexibility, is gradually playing an important role in manufacturing process, especially suitable for large rotating parts such as propellers, impellers, etc. While providing sufficient degrees of freedom, thereby allowing greater flexibility in trajectory optimization, it also increases the difficulty of trajectory planning in joint-space. Moreover, insufficient stiffness further limits the widespread application of industrial robots in high-intensity machining. In response to this issue, this article proposes a tool posture path optimization method for 7-DOF robot-turntable milling process based on constant end-stiffness index of robot-turntable configuration machining equipment. First, the stiffness performance index of 7-DOF robot-turntable configuration machining equipment are established, and the stiffness performance index is introduced into the robot-turntable. Taking into account other constraints such as the dexterity index of 7-DOF robot-turntable, the tool posture path optimization model based on constant stiffness performance index is then established. Finally, four sets of trajectory machining experiments and two sets of metal surface machining experiments are conducted on the 7-DOF robot-turntable configuration machining equipment. The analysis of experimental data indicate that the joint trajectory planned using the constant stiffness index effectively reduces the robot’s vibration displacement during machining, thereby decreasing surface roughness.
- 1 August 2026
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 35 (8) , 08LT01
Balancing speed-torque trade-off in a piezoelectric inchworm rotary actuator via amplified-torsional flexures
A major challenge in designing piezoelectric inchworm rotary actuators is to balance rotational speed, load capacity, and output torque while retaining power-off self-locking capability and relaxed assembly tolerance. This study presents the design and experimental evaluation of a piezoelectric inchworm rotary actuator that achieves balanced rotational performance and integrated pre-tightening regulation through a hybrid amplified-torsional flexure stator. Double-output rhombus-type compliant clamping and driving mechanisms are combined with torsional flexures to increase the angular step size and provide self-locking functionality. A pre-tightening flexure mechanism is incorporated into a built-in architecture, with the entire rotary stator housed inside the rotor, thereby ensuring structural compactness and ease of assembly. A prototype with dimensions of Φ90 mm × 55 mm is fabricated and experimentally tested. The experimental results demonstrate a maximum velocity of 99.2 mrad s −1 at 40 Hz, an output torque exceeding 453.1 N·mm, and a vertical load capacity of up to 10 kg. In addition, a minimum rotary step of 2.66 μ rad is obtained at a driving voltage of 0.06 V. Good bidirectional consistency is also achieved through the shortened actuation chain, demonstrating the promising performance enabled by the hybrid amplified-torsional compliant driving mechanism.
- 1 August 2026
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 35 (8) , 08LT01
Balancing speed-torque trade-off in a piezoelectric inchworm rotary actuator via amplified-torsional flexures
A major challenge in designing piezoelectric inchworm rotary actuators is to balance rotational speed, load capacity, and output torque while retaining power-off self-locking capability and relaxed assembly tolerance. This study presents the design and experimental evaluation of a piezoelectric inchworm rotary actuator that achieves balanced rotational performance and integrated pre-tightening regulation through a hybrid amplified-torsional flexure stator. Double-output rhombus-type compliant clamping and driving mechanisms are combined with torsional flexures to increase the angular step size and provide self-locking functionality. A pre-tightening flexure mechanism is incorporated into a built-in architecture, with the entire rotary stator housed inside the rotor, thereby ensuring structural compactness and ease of assembly. A prototype with dimensions of Φ90 mm × 55 mm is fabricated and experimentally tested. The experimental results demonstrate a maximum velocity of 99.2 mrad s −1 at 40 Hz, an output torque exceeding 453.1 N·mm, and a vertical load capacity of up to 10 kg. In addition, a minimum rotary step of 2.66 μ rad is obtained at a driving voltage of 0.06 V. Good bidirectional consistency is also achieved through the shortened actuation chain, demonstrating the promising performance enabled by the hybrid amplified-torsional compliant driving mechanism.
- 13 May 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 138 (5-6) , 2281-2295
High-precision trajectory calibration for robot surface machining by meta-heuristic search algorithm from local error in machining area
- 13 May 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 138 (5-6) , 2281-2295
High-precision trajectory calibration for robot surface machining by meta-heuristic search algorithm from local error in machining area
- 2 April 2025
- Published by Cambridge University Press (CUP) in Robotica
- Vol. 43 (4) , 1491-1511
Improving machining trajectory accuracy for dual-robot system with in situ laser measurement and meta-heuristic optimization
Industrial robots are widely utilized in the machining of complex parts because of their flexibility. However, their low positioning accuracy and spatial geometric error characteristics significantly limit the contour precision of robot machined parts. Therefore, in the robot machining procedure, an in situ measurement system is typically required. This study aims to enhance the trajectory accuracy of robotic machining through robotic in situ measurement and meta-heuristic optimization. In this study, a measurement-machining dual-robot system for measurement and machining is established, consisting of a measurement robot with a laser sensor mounted at the robot end and a machining robot equipped with a machining tool. In the measuring process, high-precision standard spheres are set on the edge of the machining area, and the high-precision standard geometry is measured by the measurement robot. According to measured geometry information in the local area, the trajectory accuracy for the machining robot is improved. By utilizing the standard radius of the standard spheres and adopting a meta-heuristic optimization algorithm, this study addresses the complexity of the robot kinematics model, while also overcoming local optima commonly introduced by gradient-based iterative methods. The results of the experiments in this study confirm that the proposed method markedly refines the precision of the robot machining trajectory.
- 2 April 2025
- Published by Cambridge University Press (CUP) in Robotica
- Vol. 43 (4) , 1491-1511
Improving machining trajectory accuracy for dual-robot system with in situ laser measurement and meta-heuristic optimization
Industrial robots are widely utilized in the machining of complex parts because of their flexibility. However, their low positioning accuracy and spatial geometric error characteristics significantly limit the contour precision of robot machined parts. Therefore, in the robot machining procedure, an in situ measurement system is typically required. This study aims to enhance the trajectory accuracy of robotic machining through robotic in situ measurement and meta-heuristic optimization. In this study, a measurement-machining dual-robot system for measurement and machining is established, consisting of a measurement robot with a laser sensor mounted at the robot end and a machining robot equipped with a machining tool. In the measuring process, high-precision standard spheres are set on the edge of the machining area, and the high-precision standard geometry is measured by the measurement robot. According to measured geometry information in the local area, the trajectory accuracy for the machining robot is improved. By utilizing the standard radius of the standard spheres and adopting a meta-heuristic optimization algorithm, this study addresses the complexity of the robot kinematics model, while also overcoming local optima commonly introduced by gradient-based iterative methods. The results of the experiments in this study confirm that the proposed method markedly refines the precision of the robot machining trajectory.
- 15 January 2025
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 36 (2) , 025016
A robot in-place geometric model reconstruction method for additive manufacturing parts by fusing 3D scanner measuring data
Geometric model reconstruction of additive manufacturing (AM) parts based on in-place measurement (IPM) is meaningful in realizing the robotic post-processing of AM parts. However, the low motion accuracy of the robot and the low efficiency of the IPM system restrict the development of the in-place model reconstruction. This paper presents a reconstruction method that integrates the 3D scanner and the robotic IPM system to improve the accuracy and efficiency of the model reconstruction. First, considering the measurement errors in the robotic IPM system, an error correction model is developed by measuring the calibration ball (CB) at the boundary of the measurement space. For each CB, a modified correction matrix (MCM) is constructed based on measurement data and geometric parameters of the CB to compensate for measurement errors. Second, a CB in the measurement space is measured, and the MCMs of each CB at the boundary are combined using the neural network model. Based on the measurement data of the CB, a geometric error correction model for the entire measurement space is developed, which corrects the spatial distribution of geometric errors in the robotic IPM system and enhances its accuracy within the measurement space. Finally, a local motion algorithm based on IPM data is proposed to calibrate the large volume of point cloud data from a 3D scanner. A high-precision model of AM parts is quickly reconstructed by fusing the few high-accuracy robotic IPM data with the large volume of low-accuracy point cloud data obtained by the 3D scanner. In order to verify the effectiveness of the method proposed in this paper, the measurement experiments on the CB are conducted. The results show that the model reconstruction accuracy can reach 0.06 mm compared with point cloud data obtained by the 3D scanner. The AM concave and convex parts are measured and the manufacturing geometric accuracy is analyzed by the proposed method. Compared to the digital model, the maximum deviation of the AM concave part is 1.3864 mm, and the maximum deviation of the AM convex part is 1.6802 mm.
- 15 January 2025
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 36 (2) , 025016
A robot in-place geometric model reconstruction method for additive manufacturing parts by fusing 3D scanner measuring data
Geometric model reconstruction of additive manufacturing (AM) parts based on in-place measurement (IPM) is meaningful in realizing the robotic post-processing of AM parts. However, the low motion accuracy of the robot and the low efficiency of the IPM system restrict the development of the in-place model reconstruction. This paper presents a reconstruction method that integrates the 3D scanner and the robotic IPM system to improve the accuracy and efficiency of the model reconstruction. First, considering the measurement errors in the robotic IPM system, an error correction model is developed by measuring the calibration ball (CB) at the boundary of the measurement space. For each CB, a modified correction matrix (MCM) is constructed based on measurement data and geometric parameters of the CB to compensate for measurement errors. Second, a CB in the measurement space is measured, and the MCMs of each CB at the boundary are combined using the neural network model. Based on the measurement data of the CB, a geometric error correction model for the entire measurement space is developed, which corrects the spatial distribution of geometric errors in the robotic IPM system and enhances its accuracy within the measurement space. Finally, a local motion algorithm based on IPM data is proposed to calibrate the large volume of point cloud data from a 3D scanner. A high-precision model of AM parts is quickly reconstructed by fusing the few high-accuracy robotic IPM data with the large volume of low-accuracy point cloud data obtained by the 3D scanner. In order to verify the effectiveness of the method proposed in this paper, the measurement experiments on the CB are conducted. The results show that the model reconstruction accuracy can reach 0.06 mm compared with point cloud data obtained by the 3D scanner. The AM concave and convex parts are measured and the manufacturing geometric accuracy is analyzed by the proposed method. Compared to the digital model, the maximum deviation of the AM concave part is 1.3864 mm, and the maximum deviation of the AM convex part is 1.6802 mm.
- 25 April 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 132 (9-10) , 4841-4855
Axis path planning of five-axis surface machining by optimizing differential vector of the axis movement considering tool posture limits
- 25 April 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 132 (9-10) , 4841-4855
Axis path planning of five-axis surface machining by optimizing differential vector of the axis movement considering tool posture limits
- Open Access
Driving Force and Blossoming Analysis of a Composite Triangular Rollable and Collapsible (TRAC) Boom Used in Aerospace Technologies
Deployable and foldable tape-spring booms are widely used in aerospace technologies, especially for large-scale membrane structures. Semi-circular (STEM) and lenticular (CTM) boom cross-sections were invented for specific applications since these configurations have either a concise structure or a high twisting stiffness. Moreover, a triangular cross-section (TRAC) boom was proposed years ago, as its more scattered configuration could afford a higher bending stiffness after deployment. Meanwhile, blossoming is one of the most serious failure modes during boom deployment, and is commonly caused by a relatively high load acting on the boom tip. For the sake of avoiding blossoming failure, the highest load a boom can withstand should be found theoretically for a better design. This paper aims at acquiring the highest tip load (i.e., driving force) a TRAC boom can withstand through establishing an analytical model. Furthermore, a numerical analysis is carried out to provide some verification, whose modeling and analysis method has been verified by a comparison with the experimental data from previous investigations. The research in this paper gives more guidance for the design of deployable TRAC tape-spring booms.
Open AccessDriving Force and Blossoming Analysis of a Composite Triangular Rollable and Collapsible (TRAC) Boom Used in Aerospace Technologies
Deployable and foldable tape-spring booms are widely used in aerospace technologies, especially for large-scale membrane structures. Semi-circular (STEM) and lenticular (CTM) boom cross-sections were invented for specific applications since these configurations have either a concise structure or a high twisting stiffness. Moreover, a triangular cross-section (TRAC) boom was proposed years ago, as its more scattered configuration could afford a higher bending stiffness after deployment. Meanwhile, blossoming is one of the most serious failure modes during boom deployment, and is commonly caused by a relatively high load acting on the boom tip. For the sake of avoiding blossoming failure, the highest load a boom can withstand should be found theoretically for a better design. This paper aims at acquiring the highest tip load (i.e., driving force) a TRAC boom can withstand through establishing an analytical model. Furthermore, a numerical analysis is carried out to provide some verification, whose modeling and analysis method has been verified by a comparison with the experimental data from previous investigations. The research in this paper gives more guidance for the design of deployable TRAC tape-spring booms.
- 2 June 2023
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 24 (10) , 1821-1833
Iterative Generation Method of Arc Length Parameterized Curve Tool Path for Surface Machining from Short-Line Tool Path
- 2 June 2023
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 24 (10) , 1821-1833
Iterative Generation Method of Arc Length Parameterized Curve Tool Path for Surface Machining from Short-Line Tool Path
- Open Access
Roll-Out Deployment Process Analysis of a Fiber Reinforced Polymer (FRP) Composite Tape-Spring Boom
Deployable extendable booms are widely used in aerospace technology due to many advantages they have, such as high folded-ratio, lightweight and self-deployable properties. A bistable FRP composite boom can not only extend its tip outwards with a corresponding rotation speed on the hub, but can also drive the hub rolling outwards with a fixed boom tip, which is commonly called roll-out deployment. In a bistable boom’s roll-out deployment process, the second stability can keep the coiled section from chaos without introducing a controlling mechanism. Because of this, the boom’s roll-out deployment velocity is not under control, and a high moving speed at the end will give the structure a big impact. Therefore, predicting the velocity in this whole deployment process is necessary to be researched. This paper aims to analyze the roll-out deployment process of a bistable FRP composite tape-spring boom. First, based on the Classical Laminate Theory, a dynamic analytical model of a bistable boom is established through the energy method. Afterwards, an experiment is introduced to produce some practical verification for comparison with the analytical results. According to the comparison with the experiment, the analytical model is verified for predicting the deployment velocity when the boom is relatively short, which can cover most booms using CubeSats. Finally, a parametric study reveals the relationship between the boom properties and the deployment behaviors. The research of this paper will give some guidance to the design of a composite roll-out deployable boom.
Open AccessRoll-Out Deployment Process Analysis of a Fiber Reinforced Polymer (FRP) Composite Tape-Spring Boom
Deployable extendable booms are widely used in aerospace technology due to many advantages they have, such as high folded-ratio, lightweight and self-deployable properties. A bistable FRP composite boom can not only extend its tip outwards with a corresponding rotation speed on the hub, but can also drive the hub rolling outwards with a fixed boom tip, which is commonly called roll-out deployment. In a bistable boom’s roll-out deployment process, the second stability can keep the coiled section from chaos without introducing a controlling mechanism. Because of this, the boom’s roll-out deployment velocity is not under control, and a high moving speed at the end will give the structure a big impact. Therefore, predicting the velocity in this whole deployment process is necessary to be researched. This paper aims to analyze the roll-out deployment process of a bistable FRP composite tape-spring boom. First, based on the Classical Laminate Theory, a dynamic analytical model of a bistable boom is established through the energy method. Afterwards, an experiment is introduced to produce some practical verification for comparison with the analytical results. According to the comparison with the experiment, the analytical model is verified for predicting the deployment velocity when the boom is relatively short, which can cover most booms using CubeSats. Finally, a parametric study reveals the relationship between the boom properties and the deployment behaviors. The research of this paper will give some guidance to the design of a composite roll-out deployable boom.
- Open Access
- 24 April 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (9) , 5328
Ball-End Cutting Tool Posture Optimization for Robot Surface Milling Considering Different Joint Load
Robots with openness and flexibility have attracted a large number of researchers to conduct in-depth studies in the field of surface machining. However, there is a redundant degree of freedom (DOF) in 6-DOF robot machining: when a ball end milling cutter is used to process curved parts, the tool point needs to strictly follow the planned milling trajectory, but the tool axis vector only needs to be within a certain range. During the machining process, the rotation of the tool around its axis is not constrained. Therefore, it is necessary to optimize the redundant DOF. Aiming at the redundant DOF of the tool axis vector in ball end milling for surface parts, a Redundancy Optimization strategy for Minimum Joint trajectory (ROMJ) is proposed. It takes the shortest trajectory of robot joints as the optimization objective, and the numerical optimization method is adopted to carry out the optimal design of tool axis vector trajectory in the milling process. Before optimization, to decrease the data volume, the number of track points is sampled and adjusted based on curve characterization errors. In the optimization process, considering the obvious difference in the load quality characteristics of the robot joints, a Redundancy Optimization strategy for Minimum Joint trajectory considering the different Load of joints (ROMJ-L) is proposed. The load difference coefficients of each joint are introduced into the optimization objective of the trajectory of robot joints. By using this method, the optimal design of each joint trajectory of the robot is realized. In order to verify the methods proposed in this paper, a comparison experiment is carried out. The results show that under the same tool point trajectory, the proposed methods can significantly reduce the robot joint trajectory, and the joint trajectory is influenced by the load difference of each joint. Finally, an Eflin-10 robot is used to process the butterfly trajectory tool path by the trajectory planned by the ROMJ-L method, and the results show that the method is practical.
- 24 April 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (9) , 5328
Open AccessBall-End Cutting Tool Posture Optimization for Robot Surface Milling Considering Different Joint Load
Robots with openness and flexibility have attracted a large number of researchers to conduct in-depth studies in the field of surface machining. However, there is a redundant degree of freedom (DOF) in 6-DOF robot machining: when a ball end milling cutter is used to process curved parts, the tool point needs to strictly follow the planned milling trajectory, but the tool axis vector only needs to be within a certain range. During the machining process, the rotation of the tool around its axis is not constrained. Therefore, it is necessary to optimize the redundant DOF. Aiming at the redundant DOF of the tool axis vector in ball end milling for surface parts, a Redundancy Optimization strategy for Minimum Joint trajectory (ROMJ) is proposed. It takes the shortest trajectory of robot joints as the optimization objective, and the numerical optimization method is adopted to carry out the optimal design of tool axis vector trajectory in the milling process. Before optimization, to decrease the data volume, the number of track points is sampled and adjusted based on curve characterization errors. In the optimization process, considering the obvious difference in the load quality characteristics of the robot joints, a Redundancy Optimization strategy for Minimum Joint trajectory considering the different Load of joints (ROMJ-L) is proposed. The load difference coefficients of each joint are introduced into the optimization objective of the trajectory of robot joints. By using this method, the optimal design of each joint trajectory of the robot is realized. In order to verify the methods proposed in this paper, a comparison experiment is carried out. The results show that under the same tool point trajectory, the proposed methods can significantly reduce the robot joint trajectory, and the joint trajectory is influenced by the load difference of each joint. Finally, an Eflin-10 robot is used to process the butterfly trajectory tool path by the trajectory planned by the ROMJ-L method, and the results show that the method is practical.