Kun Bo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Kun Bo has a total of 38 co-authors. Here are the top co-authors by number of shared publications:
- Jianming Peng
College of Construction Engineering, Jilin University, Changchun 130026, China
2 shared publications - Maosen Wang
School of Construction Engineering, Jilin University, Changchun, China
2 shared publications - Mingyi Guo
State Key Laboratory of Deep Earth Exploration and Imaging, College of Construction Engineering, Jilin University, Changchun 130026, China
2 shared publications - Pinlu Cao
State Key Laboratory of Deep Earth Exploration and Imaging, College of Construction Engineering, Jilin University, Changchun 130026, China
2 shared publications Baoyi Chen
College of Construction Engineering
1 shared publication- Bo Qi
School of Prospecting and Surveying, Changchun Institute of Technology, Changchun, China
1 shared publication
Latest Publications
- Open Access
Durable Superhydrophobic Polyurea Coating with Anti-Icing Properties for Hydraulic Concrete Protection
Fragile surface textures limit the durability of superhydrophobic coatings for concrete protection in cold regions. Here, we developed a polyurea-silicone composite coating containing dodecyltriethoxysilane-modified silicon carbide particles distributed throughout the matrix. Sanding the cured surface exposed the embedded particles, creating a water-repellent texture. The optimized coating combined a water contact angle of approximately 151° and a roll-off angle of 9° with a tensile strength of 5.7 MPa and a toughness of 4.86 MJ·m−3. Superhydrophobicity persisted throughout 500 sandpaper abrasion cycles, with water contact angles remaining between 150° and 152°. Pull-off tests yielded an apparent bond strength of approximately 2.39 MPa, with cohesive failure within the mortar substrate. Compared with uncoated mortar, the coating reduced ice shear adhesion strength from approximately 1240 to 37 kPa and extended the time required for complete droplet freezing at −18 °C from 24 to 266 s. Ice shear strength remained approximately 50 kPa after 50 icing–deicing cycles, while tensile properties showed negligible changes after 100 freeze–thaw cycles. These findings show that embedding hydrophobic particles throughout a flexible polymer matrix can combine abrasion-resistant superhydrophobicity, low ice adhesion, and mechanical durability, offering a route to protective coatings for hydraulic concrete in cold regions.
Open AccessDurable Superhydrophobic Polyurea Coating with Anti-Icing Properties for Hydraulic Concrete Protection
Fragile surface textures limit the durability of superhydrophobic coatings for concrete protection in cold regions. Here, we developed a polyurea-silicone composite coating containing dodecyltriethoxysilane-modified silicon carbide particles distributed throughout the matrix. Sanding the cured surface exposed the embedded particles, creating a water-repellent texture. The optimized coating combined a water contact angle of approximately 151° and a roll-off angle of 9° with a tensile strength of 5.7 MPa and a toughness of 4.86 MJ·m−3. Superhydrophobicity persisted throughout 500 sandpaper abrasion cycles, with water contact angles remaining between 150° and 152°. Pull-off tests yielded an apparent bond strength of approximately 2.39 MPa, with cohesive failure within the mortar substrate. Compared with uncoated mortar, the coating reduced ice shear adhesion strength from approximately 1240 to 37 kPa and extended the time required for complete droplet freezing at −18 °C from 24 to 266 s. Ice shear strength remained approximately 50 kPa after 50 icing–deicing cycles, while tensile properties showed negligible changes after 100 freeze–thaw cycles. These findings show that embedding hydrophobic particles throughout a flexible polymer matrix can combine abrasion-resistant superhydrophobicity, low ice adhesion, and mechanical durability, offering a route to protective coatings for hydraulic concrete in cold regions.
- Open Access
- 29 January 2026
- Published by Century Science Publishing Co in Journal of Progress in Civil Engineering
- Vol. 8 (1) , 23-27
Mechanical Properties and Wellbore Stability Analysis of Beipiao Oil Shale
This study analyzes the wellbore stability of Beipiao oil shale in Liaoning Province. XRD analysis and triaxial compression tests, conducted at bedding inclination intervals of 30° (0°, 30°, 60°, and 90°), characterize the samples as hard-brittle shale with significant mechanical anisotropy. Specifically, the cohesion and internal friction angle of the rock matrix are 17.15 MPa and 36.21°, respectively, while those of the bedding weak planes are significantly lower at 8.95 MPa and 25.85°. By coupling a transversely isotropic model with Jaeger’s criterion, the collapse pressure equivalent density was calculated under various in-situ stress regimes. The results indicate that the optimal drilling trajectory varies with the stress regime: under strike-slip and reverse faulting conditions, the optimal trajectory aligns with the maximum horizontal in-situ stress (σH), whereas under normal faulting conditions, it aligns with the minimum horizontal in-situ stress (σh). These findings provide a theoretical basis for trajectory optimization in hard-brittle laminated formations.
- 29 January 2026
- Published by Century Science Publishing Co in Journal of Progress in Civil Engineering
- Vol. 8 (1) , 23-27
Open AccessMechanical Properties and Wellbore Stability Analysis of Beipiao Oil Shale
This study analyzes the wellbore stability of Beipiao oil shale in Liaoning Province. XRD analysis and triaxial compression tests, conducted at bedding inclination intervals of 30° (0°, 30°, 60°, and 90°), characterize the samples as hard-brittle shale with significant mechanical anisotropy. Specifically, the cohesion and internal friction angle of the rock matrix are 17.15 MPa and 36.21°, respectively, while those of the bedding weak planes are significantly lower at 8.95 MPa and 25.85°. By coupling a transversely isotropic model with Jaeger’s criterion, the collapse pressure equivalent density was calculated under various in-situ stress regimes. The results indicate that the optimal drilling trajectory varies with the stress regime: under strike-slip and reverse faulting conditions, the optimal trajectory aligns with the maximum horizontal in-situ stress (σH), whereas under normal faulting conditions, it aligns with the minimum horizontal in-situ stress (σh). These findings provide a theoretical basis for trajectory optimization in hard-brittle laminated formations.
- Open Access
- 28 February 2025
- Published by Century Science Publishing Co in Journal of Progress in Civil Engineering
- Vol. 7 (2) , 35-39
Study on the Shear Strength Characteristics of Remolded Laterite from Western Henan under Different Moisture Contents
In the western Henan region of China, laterite, as a typical type of special soil, plays a significant role in the engineering properties that directly impact infrastructure development and geological disaster prevention in the area. The effect of moisture content on its mechanical properties is particularly significant. To investigate the relationship between the shear strength and moisture content of remolded laterite in western Henan, this study employs a ring shear device to conduct shear tests under various moisture content and vertical stress conditions. The analysis of the shear strength variation with strain reveals that as moisture content increases, the shear strength generally decreases. After exceeding 30% moisture content, the shear strength decreases rapidly. The cohesion decreases quickly at first with increasing moisture content, then more slowly, and finally decreases sharply. The internal friction angle decreases gradually with increasing moisture content, but the rate of decrease accelerates only after the moisture content surpasses 30%. This study provides a theoretical basis for foundation treatment and slope stability assessment in laterite areas.
- 28 February 2025
- Published by Century Science Publishing Co in Journal of Progress in Civil Engineering
- Vol. 7 (2) , 35-39
Open AccessStudy on the Shear Strength Characteristics of Remolded Laterite from Western Henan under Different Moisture Contents
In the western Henan region of China, laterite, as a typical type of special soil, plays a significant role in the engineering properties that directly impact infrastructure development and geological disaster prevention in the area. The effect of moisture content on its mechanical properties is particularly significant. To investigate the relationship between the shear strength and moisture content of remolded laterite in western Henan, this study employs a ring shear device to conduct shear tests under various moisture content and vertical stress conditions. The analysis of the shear strength variation with strain reveals that as moisture content increases, the shear strength generally decreases. After exceeding 30% moisture content, the shear strength decreases rapidly. The cohesion decreases quickly at first with increasing moisture content, then more slowly, and finally decreases sharply. The internal friction angle decreases gradually with increasing moisture content, but the rate of decrease accelerates only after the moisture content surpasses 30%. This study provides a theoretical basis for foundation treatment and slope stability assessment in laterite areas.
- 10 November 2023
- Published by Elsevier in Journal of Molecular Liquids
- Vol. 393
Synergistic effects of potassium alginate and silicates co-inhibition performance in shale hydration
- 10 November 2023
- Published by Elsevier in Journal of Molecular Liquids
- Vol. 393
Synergistic effects of potassium alginate and silicates co-inhibition performance in shale hydration
- 12 September 2023
- Published by Elsevier in Ceramics International
- Vol. 49 (23) , 37638-37649
Effects of TiB2 content and gradient structure on microstructural characterization and mechanical properties of TiB2/Al7050 composites
- 12 September 2023
- Published by Elsevier in Ceramics International
- Vol. 49 (23) , 37638-37649
Effects of TiB2 content and gradient structure on microstructural characterization and mechanical properties of TiB2/Al7050 composites
- Open Access
Optimum Design of Large-Diameter Reverse Circulation Drill Bit for Drilling Rescue Wells Using Orthogonal Experimental Method and CFD Simulation
Down-the-hole (DTH) hammer drilling with reverse circulation is a novel, mobile, high-speed drilling system suitable for the specific requirements of mine rescue. This technology can be applied to shorten the rescue time during mine accidents. The performance of reverse circulation (RC) drilling depends on the structural design of the drill bit. An orthogonal experimental design is executed to investigate the effect of the structural design parameters of the large-diameter drill bit for drilling rescue wells on the cutting carrying capacity and reverse circulation performance. This study employs computational fluid dynamics (CFD) software to solve the Navier–Stokes equation for three-dimensional steady flow and calculate the flow field around the drill bit to evaluate the RC efficiency. Six key geometric parameters were proven to have a direct influence on the RC performance, including the diameter of suction nozzles Dn, the length of nozzles L, the quantity of nozzles N, the diameter of the pilot hole Dg, the inclination angle of nozzles θs, and the deflection angle of nozzles θd. The CFD simulation experiments were implemented according to the orthogonal array L18(37) and were analyzed using the range, variance, and regression analysis. A mathematical model was developed for the RC efficiency to understand the effect of the factors. The results show that the diameter of suction nozzles Dn has an essential effect on the RC performance of the drill bit. An ideal combination is Dn = 20 mm, L = 50 mm, N = 3, Dg = 50 mm, and θs = 35°, θd = 10°, which was obtained through variance analysis and validated via CFD simulation for higher efficiency. To verify its real performance, a large-diameter RC drill bit with a diameter of 1.2 m was manufactured and tested in the field. The result demonstrated that the drill bit had excellent cutting transport and reverse circulation performance.
Open AccessOptimum Design of Large-Diameter Reverse Circulation Drill Bit for Drilling Rescue Wells Using Orthogonal Experimental Method and CFD Simulation
Down-the-hole (DTH) hammer drilling with reverse circulation is a novel, mobile, high-speed drilling system suitable for the specific requirements of mine rescue. This technology can be applied to shorten the rescue time during mine accidents. The performance of reverse circulation (RC) drilling depends on the structural design of the drill bit. An orthogonal experimental design is executed to investigate the effect of the structural design parameters of the large-diameter drill bit for drilling rescue wells on the cutting carrying capacity and reverse circulation performance. This study employs computational fluid dynamics (CFD) software to solve the Navier–Stokes equation for three-dimensional steady flow and calculate the flow field around the drill bit to evaluate the RC efficiency. Six key geometric parameters were proven to have a direct influence on the RC performance, including the diameter of suction nozzles Dn, the length of nozzles L, the quantity of nozzles N, the diameter of the pilot hole Dg, the inclination angle of nozzles θs, and the deflection angle of nozzles θd. The CFD simulation experiments were implemented according to the orthogonal array L18(37) and were analyzed using the range, variance, and regression analysis. A mathematical model was developed for the RC efficiency to understand the effect of the factors. The results show that the diameter of suction nozzles Dn has an essential effect on the RC performance of the drill bit. An ideal combination is Dn = 20 mm, L = 50 mm, N = 3, Dg = 50 mm, and θs = 35°, θd = 10°, which was obtained through variance analysis and validated via CFD simulation for higher efficiency. To verify its real performance, a large-diameter RC drill bit with a diameter of 1.2 m was manufactured and tested in the field. The result demonstrated that the drill bit had excellent cutting transport and reverse circulation performance.
- Open Access
Experimental Study on the Insulation Layer Thickness of a Novel Ice Coring Device in Loose Sandstone-Type Uranium Deposits
The target strata of sandstone-type uranium deposits are usually located in the fragile and loose strata, which makes it difficult to obtain core samples; consequently, a novel ice coring device for loose sandstone-type uranium deposits is proposed to solve this problem. Experiments proved that the artificial sample can replace the natural sample, and the coring method has high reliability. Ensuring the allegro formation of an ice valve with a given cold source is critical for this coring system, and reducing the loss of cold energy with help of insulation layer is one of the methods to speed up the formation of ice valve. Since the diameter of the drill tool is limited by its working scenario, the thickness of insulation layer is limited to ensure the size of core. Therefore, this paper conducted laboratory experiments of the insulation layer with different thicknesses to study the effect of the insulation layer on the formation of the sand–ice valve. Results show that the insulation layer can reduce the loss of cold energy during the freezing process and significantly affect the formation time of the sand–ice valve. When the thickness of the aerogel insulation layer is 2 mm, the freezing time is 44% shorter than that without insulation layer. According to the tests, the novel ice coring device is expected to solve the coring problem in loose sandstone-type uranium deposits.
Open AccessExperimental Study on the Insulation Layer Thickness of a Novel Ice Coring Device in Loose Sandstone-Type Uranium Deposits
The target strata of sandstone-type uranium deposits are usually located in the fragile and loose strata, which makes it difficult to obtain core samples; consequently, a novel ice coring device for loose sandstone-type uranium deposits is proposed to solve this problem. Experiments proved that the artificial sample can replace the natural sample, and the coring method has high reliability. Ensuring the allegro formation of an ice valve with a given cold source is critical for this coring system, and reducing the loss of cold energy with help of insulation layer is one of the methods to speed up the formation of ice valve. Since the diameter of the drill tool is limited by its working scenario, the thickness of insulation layer is limited to ensure the size of core. Therefore, this paper conducted laboratory experiments of the insulation layer with different thicknesses to study the effect of the insulation layer on the formation of the sand–ice valve. Results show that the insulation layer can reduce the loss of cold energy during the freezing process and significantly affect the formation time of the sand–ice valve. When the thickness of the aerogel insulation layer is 2 mm, the freezing time is 44% shorter than that without insulation layer. According to the tests, the novel ice coring device is expected to solve the coring problem in loose sandstone-type uranium deposits.
- Open Access
Experimental and Numerical Study on Air Flow Behavior for a Novel Retractable Reverse Circulation Drill Bit of Casing-while-Drilling (CwD)
A reverse circulation Down-The-Hole (DTH) hammer drill bit in Casing-while-Drilling (CwD) processes is designed and applied to drilling under complicated formation. The drill bit is a special retractable drill bit with an exclusive reverse circulation gas channel. Using numerical simulations and experiments, the influence of the gas channel structure parameters of the drill bit, including the inner jet nozzles, flushing nozzles, suction channel, and other parameters, on its reverse circulation performance is analyzed, and the optimal gas channel structure parameters of the drill bit are determined to improve the reverse circulation effect. The results show that the flushing nozzles and inner jet nozzles have an important influence on entrainment performance. The entrainment rate decreases as the flushing nozzle diameter increases and decreases as the inner jet nozzle diameter increases. An increase in the suction channel diameter can improve the reverse circulation effect of the drill bit. The spiral slot drill bit is more conducive to air being sucked into the central channel in the form of spiral flow, so it can improve the entrainment performance. The entrainment rate can reach 23.4% with the optimum structured drill bit.
Open AccessExperimental and Numerical Study on Air Flow Behavior for a Novel Retractable Reverse Circulation Drill Bit of Casing-while-Drilling (CwD)
A reverse circulation Down-The-Hole (DTH) hammer drill bit in Casing-while-Drilling (CwD) processes is designed and applied to drilling under complicated formation. The drill bit is a special retractable drill bit with an exclusive reverse circulation gas channel. Using numerical simulations and experiments, the influence of the gas channel structure parameters of the drill bit, including the inner jet nozzles, flushing nozzles, suction channel, and other parameters, on its reverse circulation performance is analyzed, and the optimal gas channel structure parameters of the drill bit are determined to improve the reverse circulation effect. The results show that the flushing nozzles and inner jet nozzles have an important influence on entrainment performance. The entrainment rate decreases as the flushing nozzle diameter increases and decreases as the inner jet nozzle diameter increases. An increase in the suction channel diameter can improve the reverse circulation effect of the drill bit. The spiral slot drill bit is more conducive to air being sucked into the central channel in the form of spiral flow, so it can improve the entrainment performance. The entrainment rate can reach 23.4% with the optimum structured drill bit.
- Open Access
- 20 October 2016
- Published by MDPI AG in Applied Sciences
- Vol. 6 (10) , 305
Performance Study of a Fluidic Hammer Controlled by an Output-Fed Bistable Fluidic Oscillator
Using a no-moving-component output-fed bistable fluidic oscillator to control fluid flows into a parallel path has been recognized for a considerable time, but as yet it is not so widely adopted as its obvious benefits would deserve. This may be attributed to the encountered problems associated with its jet behavior, complicated by its loading characteristics. In order to investigate a typical case for the application of the output-fed fluidic oscillator, this paper elaborates on the computational fluid dynamics (CFD) simulation method for studying the performance of a fluidic hammer controlled by an output-fed bistable fluidic oscillator. Given that couple mechanism exists between the flow field in the fluidic oscillator and the impact body, dynamic mesh technique and a user-defined function written in C programming language were used to update the mesh in the simulations. In terms of the evaluation of performance, the focus is on the single-impact energy and output power of the fluidic hammer in this study, to investigate the effect of different parameters of the impact body on them. Experimental tests based on the noncontact measuring method were conducted to verify the simulation results, by which the accuracy and reliability of this CFD simulation method was proved.
- 20 October 2016
- Published by MDPI AG in Applied Sciences
- Vol. 6 (10) , 305
Open AccessPerformance Study of a Fluidic Hammer Controlled by an Output-Fed Bistable Fluidic Oscillator
Using a no-moving-component output-fed bistable fluidic oscillator to control fluid flows into a parallel path has been recognized for a considerable time, but as yet it is not so widely adopted as its obvious benefits would deserve. This may be attributed to the encountered problems associated with its jet behavior, complicated by its loading characteristics. In order to investigate a typical case for the application of the output-fed fluidic oscillator, this paper elaborates on the computational fluid dynamics (CFD) simulation method for studying the performance of a fluidic hammer controlled by an output-fed bistable fluidic oscillator. Given that couple mechanism exists between the flow field in the fluidic oscillator and the impact body, dynamic mesh technique and a user-defined function written in C programming language were used to update the mesh in the simulations. In terms of the evaluation of performance, the focus is on the single-impact energy and output power of the fluidic hammer in this study, to investigate the effect of different parameters of the impact body on them. Experimental tests based on the noncontact measuring method were conducted to verify the simulation results, by which the accuracy and reliability of this CFD simulation method was proved.