DXDeming Xiong

Deming Xiong

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Deming Xiong has a total of 15 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Foamed ceramsite derived from oil-based drilling cutting residue and fly ash: basic properties, risk assessment, and application

    by Deming Xiong, Zheng Sun

    Oil-based drilling cuttings residue (OBDCR) and fly ash (FA) are hazardous industrial solid wastes whose safe and cost-effective disposal remains an environmental challenge. This study addresses this issue by developing a novel approach to transform OBDCR and FA into value-added foamed ceramsite, thereby contributing to sustainable waste management and resource recovery. The primary aim was to optimize the synthesis parameters to produce a lightweight, high-strength, and environmentally stable material. Using OBDCR and FA as the main raw materials and borax as a fluxing agent, a univariate experimental design was employed to systematically investigate the effects of calcination temperature, duration, and foaming agent content on the material's properties. The ceramsite was characterized in terms of porosity, water absorption, compressive strength, acid/alkali resistance, and heavy metal leaching potential. Results demonstrated that under optimal conditions (850 °C, 1 h, 6% foaming agent, and OBDCR:FA:Borax = 35:35:30), the foamed ceramsite exhibited superior performance: 65% porosity, 14.9% water absorption, 4.02 MPa compressive strength, and acid/alkali resistance exceeding 99%. Critically, the leaching concentrations of heavy metals were significantly below the limits of Chinese national standard GB/T 5085.3, and multiple ecological risk assessment methods confirmed negligible environmental hazards. Pilot-scale experiments further validated the feasibility and economic potential of this approach. This work presents a novel, efficient, and low-risk pathway for the utilization of hazardous solid wastes, offering a practical inorganic material solution for industrial waste recycling and environmental protection.


  • Open Access

    Physicochemical properties and heavy metals characteristics of building ceramsites with oil-based drilling cutting residues

    by Deming Xiong, Chaoqiang Wang

    Oil-based drilling cutting residues (OBDCRs) are among the primary solid wastes generated during shale gas exploration and development. Utilizing existing equipment to transform OBDCRs into ceramsites appears to be a feasible and resource-efficient approach. In this study, building ceramsites were prepared with OBDCRs incorporating with fly ash (a byproduct of coal combustion) as raw materials. The aim was to comprehensively and systematically investigate physicochemical properties and characteristics of heavy metals (HMs) in the ceramsites. Research shows that building ceramsites can indeed be prepared using OBDCRs, which exhibit good comprehensive properties and strong resistance to acid/ alkali. The main HMs found in ceramsite are barium (Ba), chromium (Cr), nickel (Ni), lead (Pb), arsenic (As), cadmium (Cd), and mercury (Hg). During the calcination process, these OBDCRs, along with fly ash and foaming agent, underwent mutual melting, resulting in the formation of glass, anorthite and mullite. These newly formed phases effectively encapsulated HMs, resulting in varying degrees of enrichment of HMs such as As, Ba, Pb, Cr, and Ni, except for Cd and Hg. However, the leaching toxicity of these HMs in the ceramsite was significantly lower compared to that of the original OBDCRs. Further analysis revealed a significant increase in the proportion of Fe–Mn Oxides and Organic Matter in HMs such as Cr, Ni, As, Cd, and Pb, while the proportion of Exchangeable and Carbonates forms decreased markedly. This trend clearly demonstrated that the calcination process modified the physical and chemical properties of the ceramsite, and effectively stabilized HMs, i.e., migrated from an active state to a more stable form.


  • The pozzolanic activity of calcined oil-based drilling cuttings—aluminosilicate composites

    by Deming Xiong, Chaoqiang Wang

    In order to reduce the environmental impact of shale gas production and towards the attenuation of artificial pozzolanic materials production cost, new oil-based drilling cuttings (OBDCs) pozzolanic materials have been introduced. After calcination, the chemical composition and the pozzolanic activity of oil-based drilling cuttings residue (OBDCRs) were investigated. The combination of X-ray diffraction (XRD), thermogravimetric analysis (TG), and Fourier transform infrared (FTIR) techniques shed light on impacts of pretreatment, calcination temperature, and Ba2+ on minerals’ structure and pozzolanic activity. The results showed that, after high temperature calcination, the components of Si or Al in the OBDCRs particle surface and structure were activated and recombined to produce corresponding activity. Ba2+ could promote the pozzolanic activity of OBDCRs. The 28-day-compressive strength of OBDCRs was bigger than 31.33Mpa, and the compression strength ratios of cement mortar were bigger than 65%. Therefore, the pozzolanic reactivity of the treated OBDCs was competitive with that of conventional shale, which indicates that the heat treatment of OBDCs produces a cement substitute without any secondary pollution.


  • Correction to: Characteristic pollutant purification analysis of modified phosphogypsum comprehensive utilization

    by Chao‑Qiang Wang, De‑Ming Xiong, Yu Chen, Kai Wu, Min‑Jie Tu, Pei‑Xin Wang, Zhao‑Ji Zhang, Lei Zhou


  • Characteristic pollutant purification analysis of modified phosphogypsum comprehensive utilization

    by Chao-Qiang Wang, De-Ming Xiong, Yu Chen, Kai Wu, Min-Jie Tu, Pei-Xin Wang, Zhao-Ji Zhang, Lei Zhou

    The waste product phosphogypsum (PG) is produced in phosphoric acid production processes. Its storage requires large amounts of land resources and poses serious environmental risks. In this work, detailed experimental research was carried out to investigate the potential reuse of PG after calcination modification as a novel building material for cast-in-place concrete products. The calcination modification mechanism was studied, and the environmental risk assessment of modified PG was presented. The results showed that the calcination modification includes crystal phase transformation, removal of impurities, and modifying the pH value. The calcination was carried out at 280 °C for 5 h, where the resulting product was a pH value of 7.1, and the soluble fluorine and phosphorus removal rates reached up to 69.2% and 71.2%, respectively. These removal rates met the requirements of the China national standard Phosphogypsum (GB/T 23456-2018). To ensure the environmental safety, ecological risk assessment methods for determining the leaching toxicity of the modified PG were employed. The toxicity of Ba and P elements in the modified PG products was assessed, as well as the leaching toxicity concentrations of all particular heavy metals, which were found well below the limits set by the national standards. All the results presented strongly suggest that the 280 °C modified PG presented here has excellent application potential as a raw component in building materials.


  • Particular pollutants, human health risk and ecological risk of oil-based drilling fluid: a case study of Fuling shale gas field

    by Deming Xiong, Xu Han

    Samples of new oil-based drilling fluid (NOBDF) and circulating oil-based drilling fluid (COBDF) in Chongqing were tested and analyzed to evaluate the possible impact of oil-based drilling fluid (OBDF) on human health and ecological environment. Organic matter, metals, and naturally occurring radionuclide materials (NORMs) in OBDF samples were analyzed and determined by gas chromatography-mass spectrometry, high-performance liquid chromatography, PANalytical Axios Fast XRF spectrometer, and gamma ray spectrometer. The results revealed that the contents of trace metals and NORMs in OBDF were less, which would not cause local ecological risk or health risk to the drilling crew. However, the concentrations of various aromatics analyzed in OBDF were very high, which was easy to pose serious environmental and health hazards. There were 8 aromatic hydrocarbons (AHs) in NOBDF and 15 AHs in COBDF. And the total carcinogenic risk value of each aromatic hydrocarbon was far greater than 10–4, which belonged to an unacceptable level. In addition, the inhalation pathway seemed to be the most significant source of carcinogenic risk, accounting for 99% of the total carcinogenic risk. Meanwhile, it is recommended to equip drilling workers with gas masks and develop all-oil biodiesel drilling fluid.


  • Open Access

    Characteristic Pollutants Purification Analysis of Modified Phosphogypsum Comprehensive Utilization

    by Chao-Qiang Wang, De-Ming Xiong, Yu Chen, Kai Wu, Pei-Xin Wang, Zhao-Ji Zhang, Lei Zhou

    The waste product Phosphogypsum (PG) produces in phosphoric acid production processes. Its storage requires large amounts of land resources and exist serious environmental risks. In this work detailed experimental research was carried out to investigate the potential reuse of PG after calcination modification as a novel building material for cast-in-place concrete products. The calcination modification mechanism was studied and the environmental risk assessment of modified PG is presented. The calcination modification includes crystal phase transformation, removal of impurities and modifying the pH value. The calcination was carried out at 280℃ for 3-4 hours, where the resulting product is a pH value of 7.3, and the soluble fluorine and phosphorus removal rates reach up to 72.7% and 82.4% respectively. These removal rates meet the requirements of the national Phosphogypsum standard (GB/T 23456-2009). To ensure the environmental safety, ecological risk assessment methods for determining the leaching toxicity of the modified PG were employed. The toxicity of Ba and P elements in the modified PG products was assessed, as well as the leaching toxicity concentrations of all particular heavy metals, which were found well below the limits set by the national standards. All the results presented strongly suggest that the 280℃ modified PG presented here has excellent application potential as a raw component in building materials.

  • Particular pollutants, physical properties, and environmental performance of porous ceramsite materials containing oil-based drilling cuttings residues

    by Deming Xiong, Chaoqiang Wang, Xin Huang

    The mineral compositions of oil-based drilling cutting residues (ODCRs) were similar to that of clay, which could be used as raw materials for ceramsite. In this study, the maximum addition of ODCRs and the optimum calcination conditions were studied by single factor experiment. The microstructure, phase composition, and element distribution of ceramsite were studied by means of SEM, XRD and EDS. The ceramsite, with a 40% ODCRs content, was calcined at 1000 °C for 2 h. After cooling down, the ceramsite had good physical properties, including low density, low water absorption, and high compressive strength. The bulk density was 850–970 kg/m3, the water absorption was 2.1–10%, and the cylinder compressive strength was 6–11.8 MPa. And most of the heavy metals in ODCRs were effectively solidified. The organic toxic substances were completely burned. The leaching amount of harmful elements met the requirements of Chinese standards. The ceramsite would avoid secondary pollution to the environment. So the ceramsite made from ODCRs can not only improve the processing speed of ODCRs, but also be used as building materials, greening materials, industrial filter materials, etc., and increase its environmental and social benefits.