Aliff Farhan Mohd Yamin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Aliff Farhan Mohd Yamin has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Hamid Yusoff
Universiti Teknologi Mara Cawangan Pulau Pinang
4 shared publications - Wan Mazlina Wan Mohamed
Malaysia Institute of Transport (MITRANS), Universiti Teknologi MARA, Malaysia
4 shared publications - Koay Mei Hyie
Universiti Teknologi MARA Cawangan Pulau Pinang, Permatang Pauh Campus
3 shared publications - Mohd Azmi Ismail
School of Mechanical Engineering, Universiti Sains Malaysia, Nibong Tebal, Malaysia
3 shared publications - Muhammad Ridzwan Ramli
Malaysia Institute of Transport (MITRANS), College of Engineering, College of Engineering, Universiti Teknologi MARA Shah Alam, 40450 Shah Alam, Selangor, Malaysia
3 shared publications - Siti Nur Amalina Mohd Halidi
Universiti Teknologi MARA
2 shared publications
Latest Publications
- 6 May 2025
- Published by Rynnye Lyan Resources in Food Research
- Vol. 9 (Supplement) , 215
Implementation of an Internet of Things-based monitoring system to evaluate solar dryer performance on mullet fish
Solar drying is a widely used method for food preservation, offering a flexible and environmentally friendly approach. However, traditional open sun drying methods are inefficient and susceptible to losses and contamination. To address these limitations, a solar dryer with an Internet of Things (IoT)-based weight monitoring system was developed for drying mullet fish. The solar dryer was constructed using polycarbonate material and divided into two sections: a preparation section and a drying section. An IoTbased weighing system using load cells and an Arduino MKR 1010 board was implemented to monitor the weight reduction of the fish during the drying process. The performance of the solar dryer was evaluated based on weight reduction, temperature, relative humidity, moisture removal rate, and heat transfer. The results showed that the solar dryer achieved higher moisture removal rates (6.75 g/h) and total moisture loss (21.6%) compared to open sun drying which were 5.59 g/h and 17.9%, respectively. The weight reduction percentage and moisture removal rate varied depending on the day and relative humidity inside the solar dryer. The developed solar dryer with the IoT-based weight monitoring system provides real-time feedback to workers, improves drying efficiency, and ensures consistent product quality. It offers a promising solution for enhancing food preservation and reducing post-harvest losses in Malaysia and other regions with abundant solar energy.
- 6 May 2025
- Published by Rynnye Lyan Resources in Food Research
- Vol. 9 (Supplement) , 215
Implementation of an Internet of Things-based monitoring system to evaluate solar dryer performance on mullet fish
Solar drying is a widely used method for food preservation, offering a flexible and environmentally friendly approach. However, traditional open sun drying methods are inefficient and susceptible to losses and contamination. To address these limitations, a solar dryer with an Internet of Things (IoT)-based weight monitoring system was developed for drying mullet fish. The solar dryer was constructed using polycarbonate material and divided into two sections: a preparation section and a drying section. An IoTbased weighing system using load cells and an Arduino MKR 1010 board was implemented to monitor the weight reduction of the fish during the drying process. The performance of the solar dryer was evaluated based on weight reduction, temperature, relative humidity, moisture removal rate, and heat transfer. The results showed that the solar dryer achieved higher moisture removal rates (6.75 g/h) and total moisture loss (21.6%) compared to open sun drying which were 5.59 g/h and 17.9%, respectively. The weight reduction percentage and moisture removal rate varied depending on the day and relative humidity inside the solar dryer. The developed solar dryer with the IoT-based weight monitoring system provides real-time feedback to workers, improves drying efficiency, and ensures consistent product quality. It offers a promising solution for enhancing food preservation and reducing post-harvest losses in Malaysia and other regions with abundant solar energy.
- 5 June 2024
- Published by Springer Nature
- p. 365-369
Prediction of the 96.5Sn-3.0Ag-0.5Cu Stress–Strain Curves Using Artificial Neural Network
- 5 June 2024
- Published by Springer Nature
- p. 365-369
Prediction of the 96.5Sn-3.0Ag-0.5Cu Stress–Strain Curves Using Artificial Neural Network
- Open Access
- 3 February 2023
- Published by Akademia Baru Publishing in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
- Vol. 102 (1) , 171-183
The Aerodynamic Characteristics Investigation on NACA 0012 Airfoil with Owl’s Wing Serrations for Future Air Vehicle
Owls have an incredibly unique ability to fly in silence, and this ability has significant potential to reduce noise pollution from aircraft engines. For decades, researchers have been studying the noise abatement system in conventional aircraft, but only a few of them had looked into the owl’s ability to reduce the aircraft noise level, especially on the serrated wing. The present study aims to investigate the lift and drag coefficient of the serrated wings including leading-edge serrations, trailing-edge serrations, both-edge serrations, and the original/baseline wing model from the NACA 0012 airfoil. The experimental testing was performed in a wind tunnel at Reynolds numbers of 20,000 and 40,000 and angle of attack from 2° to 30°, in 2° angle intervals. In general, the results showed that each wing model produced a similar lift and drag coefficient profiles, which were proportional to the angle of attack. At Reynolds number of 40,000, the lift coefficient increases from 0.45 to 1.5, as the angle of attack increases from 2° to 24°. Afterward, it decreased as the angle of attack exceeded 24°. According to the data, the trailing-edge serrations model showed the lowest drag coefficient at a Reynolds number of 40,000. Meanwhile, the highest lift coefficient at Reynolds number of 40,000 had been produced by the baseline wing model. This result is beneficial in reducing the noise generation produced by wing structure and at the same time enhancing aerodynamic efficiency.
- 3 February 2023
- Published by Akademia Baru Publishing in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
- Vol. 102 (1) , 171-183
Open AccessThe Aerodynamic Characteristics Investigation on NACA 0012 Airfoil with Owl’s Wing Serrations for Future Air Vehicle
Owls have an incredibly unique ability to fly in silence, and this ability has significant potential to reduce noise pollution from aircraft engines. For decades, researchers have been studying the noise abatement system in conventional aircraft, but only a few of them had looked into the owl’s ability to reduce the aircraft noise level, especially on the serrated wing. The present study aims to investigate the lift and drag coefficient of the serrated wings including leading-edge serrations, trailing-edge serrations, both-edge serrations, and the original/baseline wing model from the NACA 0012 airfoil. The experimental testing was performed in a wind tunnel at Reynolds numbers of 20,000 and 40,000 and angle of attack from 2° to 30°, in 2° angle intervals. In general, the results showed that each wing model produced a similar lift and drag coefficient profiles, which were proportional to the angle of attack. At Reynolds number of 40,000, the lift coefficient increases from 0.45 to 1.5, as the angle of attack increases from 2° to 24°. Afterward, it decreased as the angle of attack exceeded 24°. According to the data, the trailing-edge serrations model showed the lowest drag coefficient at a Reynolds number of 40,000. Meanwhile, the highest lift coefficient at Reynolds number of 40,000 had been produced by the baseline wing model. This result is beneficial in reducing the noise generation produced by wing structure and at the same time enhancing aerodynamic efficiency.
- Open Access
- 9 April 2022
- Published by Akademia Baru Publishing in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
- Vol. 93 (2) , 100-110
The Evolution of Induced Drag of Multi-Winglets for Aerodynamic Performance of NACA23015
Eagle is one of the most manoeuvrable and aerodynamically efficient bird capable of soaring for a mile, and it has high gliding ratio that can reach high velocities. Unmanned Aerial Vehicles () used in military and civilian applications are required to loiter at significant altitude without being targeted by observers. However, the induced drag is usually held mainly at the wingtip, which affects the performance of the in steady state condition due to wingtip vortex. Therefore, the objectives of this paper are to study the effect of multi-winglet on different configurations in the performance of lift and drag coefficients and to analyse the flow pattern of multi-winglet with difference configurations. The wing airfoil used was with chord length of and wingspan of . The multi-winglet device was simulated using software with three, five and seven multi-winglet configurations at angles of attack between -5° to 20° (with increment of 5°) and at flying speed of . This study found that seven multi-winglets demonstrated better results in lift and drag coefficients compared to other models at low angles of attack. In conclusion, multi-winglets can improve the aerodynamic performance of airfoil in reducing the induced drag and increasing the lift coefficient, which is suitable to be implemented at low angles of attack due to the bluffing body of winglet at high angles of attack.
- 9 April 2022
- Published by Akademia Baru Publishing in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
- Vol. 93 (2) , 100-110
Open AccessThe Evolution of Induced Drag of Multi-Winglets for Aerodynamic Performance of NACA23015
Eagle is one of the most manoeuvrable and aerodynamically efficient bird capable of soaring for a mile, and it has high gliding ratio that can reach high velocities. Unmanned Aerial Vehicles () used in military and civilian applications are required to loiter at significant altitude without being targeted by observers. However, the induced drag is usually held mainly at the wingtip, which affects the performance of the in steady state condition due to wingtip vortex. Therefore, the objectives of this paper are to study the effect of multi-winglet on different configurations in the performance of lift and drag coefficients and to analyse the flow pattern of multi-winglet with difference configurations. The wing airfoil used was with chord length of and wingspan of . The multi-winglet device was simulated using software with three, five and seven multi-winglet configurations at angles of attack between -5° to 20° (with increment of 5°) and at flying speed of . This study found that seven multi-winglets demonstrated better results in lift and drag coefficients compared to other models at low angles of attack. In conclusion, multi-winglets can improve the aerodynamic performance of airfoil in reducing the induced drag and increasing the lift coefficient, which is suitable to be implemented at low angles of attack due to the bluffing body of winglet at high angles of attack.
- Open Access
- 17 January 2022
- Published by Akademia Baru Publishing in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
- Vol. 91 (1) , 69-82
The Optimisation of Aerodynamic Performance Enhancement of a Flapping Wing using Response Surface Methodology
Flapping-Wing Micro Air Vehicles (FW-MAVs) are small hand-held flying vehicles that can manoeuvre in constrained space owing to their lightweight, low aspect ratio and can fly in a low Reynolds number environment. Among all wing types, flapping wings have the most potential in fulfilling this flight requirement since it offers good agility in confined spaces. However, the design problem for the flapping wings lies in lift generation and figuring out the main factors that play the biggest role in generating lift. In the present work, the effects of design parameters such as camber, velocity and frequency of the flapping wing have been investigated using the response surface methodology (RSM). The standard quadratic model of RSM called Central Composite Design (CCD) was utilized to identify and optimize the flapping wing. The experimental results were found to be in good agreement with the predicted outcomes. Out of 20 experimental trials determined by CCD, the optimum camber, velocity, and frequency were found to be 15%, 4.29 m/s and 9 Hz respectively. The experimental results in this study are reasonable and accurate and can be used for describing the aerodynamic parameters. This study also established the usefulness of RSM in optimizing the aerodynamic properties for flapping wing mechanism.
- 17 January 2022
- Published by Akademia Baru Publishing in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
- Vol. 91 (1) , 69-82
Open AccessThe Optimisation of Aerodynamic Performance Enhancement of a Flapping Wing using Response Surface Methodology
Flapping-Wing Micro Air Vehicles (FW-MAVs) are small hand-held flying vehicles that can manoeuvre in constrained space owing to their lightweight, low aspect ratio and can fly in a low Reynolds number environment. Among all wing types, flapping wings have the most potential in fulfilling this flight requirement since it offers good agility in confined spaces. However, the design problem for the flapping wings lies in lift generation and figuring out the main factors that play the biggest role in generating lift. In the present work, the effects of design parameters such as camber, velocity and frequency of the flapping wing have been investigated using the response surface methodology (RSM). The standard quadratic model of RSM called Central Composite Design (CCD) was utilized to identify and optimize the flapping wing. The experimental results were found to be in good agreement with the predicted outcomes. Out of 20 experimental trials determined by CCD, the optimum camber, velocity, and frequency were found to be 15%, 4.29 m/s and 9 Hz respectively. The experimental results in this study are reasonable and accurate and can be used for describing the aerodynamic parameters. This study also established the usefulness of RSM in optimizing the aerodynamic properties for flapping wing mechanism.
- Open Access
- 5 August 2021
- Published by Akademia Baru Publishing in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
- Vol. 85 (2) , 33-43
Experimental Study of Rigid and Flexible Tandem Wing for Micro Aerial Vehicle
Unmanned aerial vehicle is becoming increasingly popular each year. Now, aeronautical researchers are focusing on size minimization of unmanned aerial vehicle, especially drone and micro aerial vehicle. The lift coefficient of micro aerial vehicle has wing dimension of 12 cm and mass of less than 7 g. In the present study, with the aid of 3D printer, polylactic acid material was used to develop the micro aerial vehicle structure for tandem wing arrangement. The materials for rigid wing skin and flexible wing skin were laminating film and latex membrane, respectively. The present work elaborates the lift coefficient profiles on rigid wing skin and flexible wing skin at wing flapping frequency of 11 Hz, three different Reynolds numbers of 14000, 19000 and 24000, and five different angles of attacks between 0° and 50°. According to the results obtained, the lift coefficient decreased as the Reynolds number increased. The lift coefficient increased up to 9 as the angle of attack increased from 0° to 50° at the Reynolds number of 14000 for flexible wing skin. The results also showed that the lift coefficient of flexible wing skin was higher than that of rigid wing skin at the attack angle of10° and below, except for the Reynolds number of 14000.
- 5 August 2021
- Published by Akademia Baru Publishing in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
- Vol. 85 (2) , 33-43
Open AccessExperimental Study of Rigid and Flexible Tandem Wing for Micro Aerial Vehicle
Unmanned aerial vehicle is becoming increasingly popular each year. Now, aeronautical researchers are focusing on size minimization of unmanned aerial vehicle, especially drone and micro aerial vehicle. The lift coefficient of micro aerial vehicle has wing dimension of 12 cm and mass of less than 7 g. In the present study, with the aid of 3D printer, polylactic acid material was used to develop the micro aerial vehicle structure for tandem wing arrangement. The materials for rigid wing skin and flexible wing skin were laminating film and latex membrane, respectively. The present work elaborates the lift coefficient profiles on rigid wing skin and flexible wing skin at wing flapping frequency of 11 Hz, three different Reynolds numbers of 14000, 19000 and 24000, and five different angles of attacks between 0° and 50°. According to the results obtained, the lift coefficient decreased as the Reynolds number increased. The lift coefficient increased up to 9 as the angle of attack increased from 0° to 50° at the Reynolds number of 14000 for flexible wing skin. The results also showed that the lift coefficient of flexible wing skin was higher than that of rigid wing skin at the attack angle of10° and below, except for the Reynolds number of 14000.
- Open Access
- 1 November 2019
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1349 (1) , 012013
Failure prediction of the solder joints in the ball-grid-array package under thermal loading
This paper studies the numerical failure mechanism of the solder joints in the ball grid array (BGA) package under thermal reliability process. The package consists of the silicon die, the Flame Retardant 4 (FR-4) substrate and the FR-4 printed circuit board (PCB). A total of 64 95.5Sn-4.0Ag-0.5Cu (SAC405) solder joints with a diameter of 0.46 mm are arranged together in area array fashion with a pitch distance of 0.8 mm. Only a quarter-model of the package is simulated since all the geometry, loading and boundary conditions (BC) is symmetry at the centre of the package. The package is exposed with thermal loading, initially at the liquidus temperature of 220°C to room temperature (25°C). Then, it follows with 3 additional thermal cycles between 125°C and -40°C with a ramp rate of 11°C/min and 15 minutes dwell time, respectively. Unified inelastic strain model (Anand model) was used to compute the inelastic behaviour of the solder joints. Results show that the stress level at the critical solder joints and the corresponding inelastic strain are 39.91 MPa of 0.2083%, respectively after the end of the solder reflow cooling process. As predicted, the inelastic strains accumulate continuously in the solder joint throughout the temperature cycles. Additionally, in the critical solder joint, both high stress and inelastic strain gradients are localized near to the solder-IMC interfaces. Prolong the thermal cycles can extensively accumulate the inelastic strains which lead to fatigue crack and subsequently crack propagation in the solder joints. After the end of the FE simulation, the highest stress and inelastic strain predicted are 57.96 MPa and 0.5781%, respectively.
- 1 November 2019
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1349 (1) , 012013
Open AccessFailure prediction of the solder joints in the ball-grid-array package under thermal loading
This paper studies the numerical failure mechanism of the solder joints in the ball grid array (BGA) package under thermal reliability process. The package consists of the silicon die, the Flame Retardant 4 (FR-4) substrate and the FR-4 printed circuit board (PCB). A total of 64 95.5Sn-4.0Ag-0.5Cu (SAC405) solder joints with a diameter of 0.46 mm are arranged together in area array fashion with a pitch distance of 0.8 mm. Only a quarter-model of the package is simulated since all the geometry, loading and boundary conditions (BC) is symmetry at the centre of the package. The package is exposed with thermal loading, initially at the liquidus temperature of 220°C to room temperature (25°C). Then, it follows with 3 additional thermal cycles between 125°C and -40°C with a ramp rate of 11°C/min and 15 minutes dwell time, respectively. Unified inelastic strain model (Anand model) was used to compute the inelastic behaviour of the solder joints. Results show that the stress level at the critical solder joints and the corresponding inelastic strain are 39.91 MPa of 0.2083%, respectively after the end of the solder reflow cooling process. As predicted, the inelastic strains accumulate continuously in the solder joint throughout the temperature cycles. Additionally, in the critical solder joint, both high stress and inelastic strain gradients are localized near to the solder-IMC interfaces. Prolong the thermal cycles can extensively accumulate the inelastic strains which lead to fatigue crack and subsequently crack propagation in the solder joints. After the end of the FE simulation, the highest stress and inelastic strain predicted are 57.96 MPa and 0.5781%, respectively.
- Open Access
- 1 February 2017
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 97, 01059
Influence of Material Properties on the Fluid-Structure Interaction aspects during Molded Underfill Process
MATEC Web of Conferences, open access proceedings in Materials science, Engineering and Chemistry
- 1 February 2017
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 97, 01059
Open AccessInfluence of Material Properties on the Fluid-Structure Interaction aspects during Molded Underfill Process
MATEC Web of Conferences, open access proceedings in Materials science, Engineering and Chemistry