Hsiao-Hsing Chou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Hsiao-Hsing Chou has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Hsin-Liang Chen
Department of Electrical and Computer Engineering, Tamkang University, 151, Yingzhuan Rd., Tamsui Dist., New Taipei City 251301, Taiwan
7 shared publications - San-Fu Wang
National Chin-Yi University of Technology College of Electrical Engineering and Computer Science Taichung and Department of Electronic Engineering, National Chin-Yi University of Technology, Taichung, Taiwan
4 shared publications - Jen-Shiun Chiang
Department of Electrical and Computer Engineering Tamkang University New Taipei City Taiwan
3 shared publications - Chun-Kai Fu
Leadtrend Technology Corporation, New Taipei City, Taiwan
2 shared publications - Wen-Hao Luo
Department of Electrical Engineering, National Penghu University of Science and Technology, Penghu, Magong City 880011, Taiwan
2 shared publications Cheng-Yu Chang
1 shared publication
Latest Publications
- 26 March 2026
- Published by Elsevier in Integration
- Vol. 109
A dual-loop controlled buck converter with fast transient response
- 26 March 2026
- Published by Elsevier in Integration
- Vol. 109
A dual-loop controlled buck converter with fast transient response
- 5 April 2025
- Published by World Scientific Pub Co Pte Ltd in Journal of Circuits, Systems and Computers
- Vol. 34 (10)
Buck Converter Scheme with High Transient Response
This paper proposed the buck converter with a high transient response. This control scheme is derived from the current mode control (CMC) architecture to further improve its transient performance. The advantages of the converter are as follows: (a) Superior transient response. The recovery time for step-up/step-down is within 1.6[ ] [ ]s. (b) The structure of the scheme is simple and easy to implement. (c) For an input voltage of 3.0–3.6[ ]V and output voltage of 1.0–2.5[ ]V, the converter maintains a constant switching frequency. This feature solves the EMI issue in applications. (d) Although the proposed scheme is derived from the CMC architecture, it does not require a current sensor. The control topology, analysis, operation principle and circuit realization of the converter are presented in this paper. In the future, the proposed circuits can be fabricated by UMC 0.18[ ] [ ]m 1P6M CMOS processes.
- 5 April 2025
- Published by World Scientific Pub Co Pte Ltd in Journal of Circuits, Systems and Computers
- Vol. 34 (10)
Buck Converter Scheme with High Transient Response
This paper proposed the buck converter with a high transient response. This control scheme is derived from the current mode control (CMC) architecture to further improve its transient performance. The advantages of the converter are as follows: (a) Superior transient response. The recovery time for step-up/step-down is within 1.6[ ] [ ]s. (b) The structure of the scheme is simple and easy to implement. (c) For an input voltage of 3.0–3.6[ ]V and output voltage of 1.0–2.5[ ]V, the converter maintains a constant switching frequency. This feature solves the EMI issue in applications. (d) Although the proposed scheme is derived from the CMC architecture, it does not require a current sensor. The control topology, analysis, operation principle and circuit realization of the converter are presented in this paper. In the future, the proposed circuits can be fabricated by UMC 0.18[ ] [ ]m 1P6M CMOS processes.
- 10 March 2025
- Published by Springer Nature in Circuits, Systems, and Signal Processing
- Vol. 44 (7) , 4487-4510
A 6th-Order Current-Mirror-Based Gm-C Bandpass Filter with the Binary Searching Calibration Scheme for Capacitor Sensing Applications
- 10 March 2025
- Published by Springer Nature in Circuits, Systems, and Signal Processing
- Vol. 44 (7) , 4487-4510
A 6th-Order Current-Mirror-Based Gm-C Bandpass Filter with the Binary Searching Calibration Scheme for Capacitor Sensing Applications
- 12 September 2024
- Published by Springer Nature in Circuits, Systems, and Signal Processing
- Vol. 44 (1) , 2-23
Discrete-Time Delta-Sigma Modulator with Successively Approximating Register ADC Assisted Analog Feedback Technique
- 12 September 2024
- Published by Springer Nature in Circuits, Systems, and Signal Processing
- Vol. 44 (1) , 2-23
Discrete-Time Delta-Sigma Modulator with Successively Approximating Register ADC Assisted Analog Feedback Technique
- Open Access
- 15 March 2024
- Published by Springer Nature in Research Square
A 6th-Order Current-Mirror-Based Gm-C Bandpass Filter with the Binary Searching Calibration Scheme for Capacitor Sensing Applications
This paper presents the current-mirror-based Gm-C bandpass filter with a digitally binary searching calibration scheme. The current-mirror-based circuit technique can be a highly regular structure, which drives the proposed filter to implement the conceptions of the modularized unit and repeatable layout. Furthermore, it employs a tunable bias current circuit and a successively counting logic to implement the binary searching calibration scheme to reduce the mass test timing budget and to obtain the correct frequency response. Thus, the proposed 6th-order current-mirror-based Gm-C bandpass filter can overcome the PVT variations with this automatically tunable bias scheme. Accordingly, a Gm-C LC oscillator, which forms the same unit cell as the filter, generates the oscillated clock for this digital successively counting calibration scheme. This work is designed and implemented in the 0.18μm CMOS process with a supply voltage of 1.8V. The specifications include the center frequency of 200kHz and bandwidth of 100kHz for capacitor sensing applications. The measured power dissipations of the filter and calibrating scheme are 0.65mW and 0.56mW, respectively. After calibrating, the mean offset and standard deviation ratios to the calibrated clock frequency are only 2.1% and 1.66%, respectively.
- 15 March 2024
- Published by Springer Nature in Research Square
Open AccessA 6th-Order Current-Mirror-Based Gm-C Bandpass Filter with the Binary Searching Calibration Scheme for Capacitor Sensing Applications
This paper presents the current-mirror-based Gm-C bandpass filter with a digitally binary searching calibration scheme. The current-mirror-based circuit technique can be a highly regular structure, which drives the proposed filter to implement the conceptions of the modularized unit and repeatable layout. Furthermore, it employs a tunable bias current circuit and a successively counting logic to implement the binary searching calibration scheme to reduce the mass test timing budget and to obtain the correct frequency response. Thus, the proposed 6th-order current-mirror-based Gm-C bandpass filter can overcome the PVT variations with this automatically tunable bias scheme. Accordingly, a Gm-C LC oscillator, which forms the same unit cell as the filter, generates the oscillated clock for this digital successively counting calibration scheme. This work is designed and implemented in the 0.18μm CMOS process with a supply voltage of 1.8V. The specifications include the center frequency of 200kHz and bandwidth of 100kHz for capacitor sensing applications. The measured power dissipations of the filter and calibrating scheme are 0.65mW and 0.56mW, respectively. After calibrating, the mean offset and standard deviation ratios to the calibrated clock frequency are only 2.1% and 1.66%, respectively.
- Open Access
- 3 February 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (3) , 1991
A New Control Scheme for the Buck Converter
In this paper, a new control scheme for buck converters was proposed. The buck converter utilizes the dual control loop to improve transient response and has the constant switching frequency. The control scheme is mainly as follows: (a) The switch-ON time is regulated by the constant frequency mechanism. (b) The switch-OFF time is regulated by the output voltage. The spec/features of the proposed converter are listed as: (1) The buck converter has an output of 1.0–2.5 V for the input of 3.0–3.6 V. The load current ranges from 100 mA to 500 mA. (2) The actual current sensor is not required. (3) The simulation results show that the recovery time is less than 1.6 μs during load changes. (4) The variation in switching frequency is smaller than 1.05% over the output range of 1.0–2.5 V. (5) This circuit can be fabricated in future by UMC 0.18 μm 1P6M CMOS processes. This paper depicts the control scheme, theoretical analysis, and implementation.
- 3 February 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (3) , 1991
Open AccessA New Control Scheme for the Buck Converter
In this paper, a new control scheme for buck converters was proposed. The buck converter utilizes the dual control loop to improve transient response and has the constant switching frequency. The control scheme is mainly as follows: (a) The switch-ON time is regulated by the constant frequency mechanism. (b) The switch-OFF time is regulated by the output voltage. The spec/features of the proposed converter are listed as: (1) The buck converter has an output of 1.0–2.5 V for the input of 3.0–3.6 V. The load current ranges from 100 mA to 500 mA. (2) The actual current sensor is not required. (3) The simulation results show that the recovery time is less than 1.6 μs during load changes. (4) The variation in switching frequency is smaller than 1.05% over the output range of 1.0–2.5 V. (5) This circuit can be fabricated in future by UMC 0.18 μm 1P6M CMOS processes. This paper depicts the control scheme, theoretical analysis, and implementation.
- 3 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 70 (3) , 1059-1063
Design and Implementation of the Linear LED Driver
This paper presents a new LED control scheme to maintain a constant LED power. In LED control schemes, the conventional approach is to maintain a constant LED current. However, this traditional approach will bring high power at high input voltage and then generate high heat. The higher heat will shorten the life time of the product and reduce the reliability. The proposed scheme can solve this problem. The LED driver with the proposed scheme has been successfully fabricated by Macronix and the feasibility of the method has been verified. From the experimental results, the higher the input voltage, the lower the LED current. This constant power method can effectively avoid overheating at high input voltage. The control scheme, the theoretical analysis and the circuit implementation are presented in this paper.
- 3 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 70 (3) , 1059-1063
Design and Implementation of the Linear LED Driver
This paper presents a new LED control scheme to maintain a constant LED power. In LED control schemes, the conventional approach is to maintain a constant LED current. However, this traditional approach will bring high power at high input voltage and then generate high heat. The higher heat will shorten the life time of the product and reduce the reliability. The proposed scheme can solve this problem. The LED driver with the proposed scheme has been successfully fabricated by Macronix and the feasibility of the method has been verified. From the experimental results, the higher the input voltage, the lower the LED current. This constant power method can effectively avoid overheating at high input voltage. The control scheme, the theoretical analysis and the circuit implementation are presented in this paper.
- Open Access
- 5 May 2022
- Published by MDPI AG in Electronics
- Vol. 11 (9) , 1484
Design of the Buck Converter without Inductor Current Sensor
This paper proposes a novel control scheme for the buck converter without an inductor current sensor. The architecture of the proposed buck converter is simple and suitable for integration and mass production. It employs an output-voltage-measurement method to determine the switch ON time; therefore, the current sensor is not required. The design specification targets the application with a standard battery power source to generate the low voltages for low-power MCU or ASIC. The load current range aims for several hundred milliamps. The proposed control scheme is analyzed and simulated by SIMPLIS. The control scheme, theoretical analysis, circuit realization, contributions, advantages, and simulation results are presented in this paper. Furthermore, the circuit can be fabricated by a 0.35 μm CMOS process.
- 5 May 2022
- Published by MDPI AG in Electronics
- Vol. 11 (9) , 1484
Open AccessDesign of the Buck Converter without Inductor Current Sensor
This paper proposes a novel control scheme for the buck converter without an inductor current sensor. The architecture of the proposed buck converter is simple and suitable for integration and mass production. It employs an output-voltage-measurement method to determine the switch ON time; therefore, the current sensor is not required. The design specification targets the application with a standard battery power source to generate the low voltages for low-power MCU or ASIC. The load current range aims for several hundred milliamps. The proposed control scheme is analyzed and simulated by SIMPLIS. The control scheme, theoretical analysis, circuit realization, contributions, advantages, and simulation results are presented in this paper. Furthermore, the circuit can be fabricated by a 0.35 μm CMOS process.
- Open Access
- 15 April 2022
- Published by MDPI AG in Electronics
- Vol. 11 (8) , 1256
A Novel Buck Converter with Dual Loops Control Mechanism
This paper presents a novel buck converter with dual-loop control technology, which does not need to detect the inductor current directly. The structure of the control loops is easy to implement, one loop controls the output voltage, and the other controls the switching frequency. With the dual loops control mechanism, the output voltage and switching frequency can be accurately controlled only by measuring the output and input voltage, without sensing the inductor current. The buck converter can generate an output voltage of 1.0–2.5 V when the input voltage and load current are 3.0–3.6 V and 100–500 mA, respectively. The design was verified by SIMPLIS. The simulation results show that the switching frequency variation is less than 1% at the output voltage of 1.0–2.5 V. The recovery time is less than 1.5 μs during the load change. The circuit can be fabricated by using the TSMC 0.35μm 2P4M CMOS processes. The control scheme, theoretical analysis and circuit implementation are presented in this paper.
- 15 April 2022
- Published by MDPI AG in Electronics
- Vol. 11 (8) , 1256
Open AccessA Novel Buck Converter with Dual Loops Control Mechanism
This paper presents a novel buck converter with dual-loop control technology, which does not need to detect the inductor current directly. The structure of the control loops is easy to implement, one loop controls the output voltage, and the other controls the switching frequency. With the dual loops control mechanism, the output voltage and switching frequency can be accurately controlled only by measuring the output and input voltage, without sensing the inductor current. The buck converter can generate an output voltage of 1.0–2.5 V when the input voltage and load current are 3.0–3.6 V and 100–500 mA, respectively. The design was verified by SIMPLIS. The simulation results show that the switching frequency variation is less than 1% at the output voltage of 1.0–2.5 V. The recovery time is less than 1.5 μs during the load change. The circuit can be fabricated by using the TSMC 0.35μm 2P4M CMOS processes. The control scheme, theoretical analysis and circuit implementation are presented in this paper.
- Open Access
A Novel Buck Converter with Constant Frequency Controlled Technique
This paper presents a buck converter with a novel constant frequency controlled technique, which employs the proposed frequency detector and adaptive on-time control (AOT) logic to lock the switching frequency. The control scheme, design concept, and circuit realization are presented. In contrast to a complex phase lock loop (PLL), the proposed scheme is easy to implement. With this novel technique, a buck converter is designed to produce an output voltage of 1.0–2.5 V at the input voltage of 3.0–3.6 V and the maximum load current of 500 mA. The proposed scheme was verified using SIMPLIS and MathCAD. The simulation results show that the switching frequency variation is less than 1% at an output voltage of 1.0–2.5 V. Furthermore, the recovery time is less than 2 μs for a step-up and step-down load transient. The circuit will be fabricated using UMC 0.18 μm 1P6M CMOS processes. The control scheme, design concept and circuit realization are presented in this paper.
Open AccessA Novel Buck Converter with Constant Frequency Controlled Technique
This paper presents a buck converter with a novel constant frequency controlled technique, which employs the proposed frequency detector and adaptive on-time control (AOT) logic to lock the switching frequency. The control scheme, design concept, and circuit realization are presented. In contrast to a complex phase lock loop (PLL), the proposed scheme is easy to implement. With this novel technique, a buck converter is designed to produce an output voltage of 1.0–2.5 V at the input voltage of 3.0–3.6 V and the maximum load current of 500 mA. The proposed scheme was verified using SIMPLIS and MathCAD. The simulation results show that the switching frequency variation is less than 1% at an output voltage of 1.0–2.5 V. Furthermore, the recovery time is less than 2 μs for a step-up and step-down load transient. The circuit will be fabricated using UMC 0.18 μm 1P6M CMOS processes. The control scheme, design concept and circuit realization are presented in this paper.