Rubab Ume
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Rubab Ume has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
Karsten Beckmann
SUNY Polytechnic Institute, Albany, NY, USA
3 shared publications- Kevin Brew
IBM AI Hardware Center 2 , Albany, New York 12222
3 shared publications Vadim Tokranov
SUNY Polytechnic Institute, Albany, NY, USA
3 shared publicationsChristian Lavoie
IBM T.J. Watson Research Center 3 , 1101 Kitchawan Road, Yorktown Heights, New York 10598, USA
2 shared publicationsGuy Cohen
IBM T.J. Watson Research Center 3 , 1101 Kitchawan Road, Yorktown Heights, New York 10598, USA
2 shared publications- Guy M. Cohen
IBM T. J. Watson Research Center
2 shared publications
Latest Publications
- Open Access
- 1 November 2025
- Published by AIP Publishing in AIP Advances
- Vol. 15 (11)
Nanoscale phase separation in Al0.4–Sb0.6 alloy for phase change memory applications
Phase change memory (PCM) is considered an enabling technology for non-volatile multilevel data storage and neuromorphic computing. Recent advancements in PCM have highlighted the need to improve resistance drift and energy efficiency. At present, binary alloys that phase-separate upon crystallization offer a promising solution. The Al–Sb binary alloy crystallizes into a rhombohedral Sb-rich phase and a cubic AlSb phase, with the latter having a higher melting temperature that enables selective melting of the Sb-rich phase for partial RESET programming. Continuum resistance states result from a reversible alloying process, in which programming pulses modulate the granularity and aluminum content of the amorphous Sb-rich phase. Al0.4–Sb0.6 PCM cells, fabricated on Si-foundry templates, exhibit a high resistance contrast of up to 4000× between fully amorphous and crystalline states, along with a low resistance drift coefficient (∼0.06). The high melting point of AlSb also leads to nanoscale compositional heterogeneity, which persists in the amorphous state, suppressing structural relaxation and thus reducing resistance drift. These findings position Al0.4–Sb0.6 as a promising material for engineering multilevel PCM cells based on phase-separating alloys.
- 1 November 2025
- Published by AIP Publishing in AIP Advances
- Vol. 15 (11)
Open AccessNanoscale phase separation in Al0.4–Sb0.6 alloy for phase change memory applications
Phase change memory (PCM) is considered an enabling technology for non-volatile multilevel data storage and neuromorphic computing. Recent advancements in PCM have highlighted the need to improve resistance drift and energy efficiency. At present, binary alloys that phase-separate upon crystallization offer a promising solution. The Al–Sb binary alloy crystallizes into a rhombohedral Sb-rich phase and a cubic AlSb phase, with the latter having a higher melting temperature that enables selective melting of the Sb-rich phase for partial RESET programming. Continuum resistance states result from a reversible alloying process, in which programming pulses modulate the granularity and aluminum content of the amorphous Sb-rich phase. Al0.4–Sb0.6 PCM cells, fabricated on Si-foundry templates, exhibit a high resistance contrast of up to 4000× between fully amorphous and crystalline states, along with a low resistance drift coefficient (∼0.06). The high melting point of AlSb also leads to nanoscale compositional heterogeneity, which persists in the amorphous state, suppressing structural relaxation and thus reducing resistance drift. These findings position Al0.4–Sb0.6 as a promising material for engineering multilevel PCM cells based on phase-separating alloys.
- 22 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 70 (7) , 3511-3516
Three Programming States in Bilayer Ga–Sb Phase Change Memory With AlO x Diffusion Barrier
Tellurium-free antimony-based phase change memory (PCM) alloys have attracted much attention due to their superior attributes such as fast switching speed, wide resistance window, and low drift. However, programming reproducible intermediate states in such PCM materials has been challenging. In this study, bilayer PCM cells comprised of Ga–Sb films with two different compositions separated by a 1-nm-thick AlO x diffusion barrier layer were fabricated on Si foundry templates with a Ø120-nm TiN heater and TaN top contact. The current–voltage measurements of the cells exhibit two threshold voltages, separating three stable resistance regions. These cells can be controllably switched among three resistance states, that is, the SET ( $\sim 10^{3} \ \Omega)$ , intermediate ( $\sim 10^{4} \ \Omega)$ , and RESET states ( $\sim 5\times 10^{5}\,\,\ \Omega {)}$ . The phase transitions during switching among three resistance states are discussed and correlated with the device resistance profiles. The stability of the AlO x barrier layer is investigated with transmission electron microscopy (TEM) and energy-dispersive X-ray spectroscopy (EDS).
- 22 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 70 (7) , 3511-3516
Three Programming States in Bilayer Ga–Sb Phase Change Memory With AlO x Diffusion Barrier
Tellurium-free antimony-based phase change memory (PCM) alloys have attracted much attention due to their superior attributes such as fast switching speed, wide resistance window, and low drift. However, programming reproducible intermediate states in such PCM materials has been challenging. In this study, bilayer PCM cells comprised of Ga–Sb films with two different compositions separated by a 1-nm-thick AlO x diffusion barrier layer were fabricated on Si foundry templates with a Ø120-nm TiN heater and TaN top contact. The current–voltage measurements of the cells exhibit two threshold voltages, separating three stable resistance regions. These cells can be controllably switched among three resistance states, that is, the SET ( $\sim 10^{3} \ \Omega)$ , intermediate ( $\sim 10^{4} \ \Omega)$ , and RESET states ( $\sim 5\times 10^{5}\,\,\ \Omega {)}$ . The phase transitions during switching among three resistance states are discussed and correlated with the device resistance profiles. The stability of the AlO x barrier layer is investigated with transmission electron microscopy (TEM) and energy-dispersive X-ray spectroscopy (EDS).
- Open Access
- 18 July 2022
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 132 (3)
Electrical and structural properties of binary Ga–Sb phase change memory alloys
Material properties of Ga–Sb binary alloy thin films deposited under ultra-high vacuum conditions were studied for analog phase change memory (PCM) applications. Crystallization of this alloy was shown to occur in the temperature range of 180–264 °C, with activation energy >2.5 eV depending on the composition. X-ray diffraction (XRD) studies showed phase separation upon crystallization into two phases, Ga-doped A7 antimony and cubic zinc-blende GaSb. Synchrotron in situ XRD analysis revealed that crystallization into the A7 phase is accompanied by Ga out-diffusion from the grains. X-ray absorption fine structure studies of the local structure of these alloys demonstrated a bond length decrease with a stable coordination number of 4 upon amorphous-to-crystalline phase transformation. Mushroom cell structures built with Ga–Sb alloys on ø110 nm TiN heater show a phase change material resistance switching behavior with resistance ratio >100 under electrical pulse measurements. TEM and Energy Dispersive Spectroscopy (EDS) studies of the Ga–Sb cells after ∼100 switching cycles revealed that partial SET or intermediate resistance states are attained by the variation of the grain size of the material as well as the Ga content in the A7 phase. A mechanism for a reversible composition control is proposed for analog cell performance. These results indicate that Te-free Ga–Sb binary alloys are potential candidates for analog PCM applications.
- 18 July 2022
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 132 (3)
Open AccessElectrical and structural properties of binary Ga–Sb phase change memory alloys
Material properties of Ga–Sb binary alloy thin films deposited under ultra-high vacuum conditions were studied for analog phase change memory (PCM) applications. Crystallization of this alloy was shown to occur in the temperature range of 180–264 °C, with activation energy >2.5 eV depending on the composition. X-ray diffraction (XRD) studies showed phase separation upon crystallization into two phases, Ga-doped A7 antimony and cubic zinc-blende GaSb. Synchrotron in situ XRD analysis revealed that crystallization into the A7 phase is accompanied by Ga out-diffusion from the grains. X-ray absorption fine structure studies of the local structure of these alloys demonstrated a bond length decrease with a stable coordination number of 4 upon amorphous-to-crystalline phase transformation. Mushroom cell structures built with Ga–Sb alloys on ø110 nm TiN heater show a phase change material resistance switching behavior with resistance ratio >100 under electrical pulse measurements. TEM and Energy Dispersive Spectroscopy (EDS) studies of the Ga–Sb cells after ∼100 switching cycles revealed that partial SET or intermediate resistance states are attained by the variation of the grain size of the material as well as the Ga content in the A7 phase. A mechanism for a reversible composition control is proposed for analog cell performance. These results indicate that Te-free Ga–Sb binary alloys are potential candidates for analog PCM applications.
- Open Access
- 1 July 2021
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 10 (7) , 075008
Crystallization Properties of Al-Sb Alloys for Phase Change Memory Applications
Material properties of Al-Sb binary alloy thin films deposited under ultra-high vacuum conditions were studied for multi-level phase change memory applications. Crystallization of this alloy was shown to occur in the temperature range of 180 °C–280 °C, with activation energy >2 eV. X-ray diffraction (XRD) from annealed alloy films indicates the formation of two crystalline phases, (i) an Al-doped A7 antimony phase, and (ii) a stable cubic AlSb phase. In-situ XRD analysis of these films show the AlSb phase crystalizes at a much higher temperature as compared to the A7 phase after annealing of the film to 650 °C. Mushroom cell structures formed with Al-Sb alloys on 120 nm TiN heater show a phase change material resistance switching behavior with reset/set resistance ratio >1000 under pulse measurements. TEM and in situ synchrotron XRD studies indicate fine nucleation grain sizes of ∼8–10 nm, and low elemental redistribution that is useful for improving reliability of the devices. These results indicate that Te-free Al-Sb binary alloys are possible candidates for analog PCM applications.
- 1 July 2021
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 10 (7) , 075008
Open AccessCrystallization Properties of Al-Sb Alloys for Phase Change Memory Applications
Material properties of Al-Sb binary alloy thin films deposited under ultra-high vacuum conditions were studied for multi-level phase change memory applications. Crystallization of this alloy was shown to occur in the temperature range of 180 °C–280 °C, with activation energy >2 eV. X-ray diffraction (XRD) from annealed alloy films indicates the formation of two crystalline phases, (i) an Al-doped A7 antimony phase, and (ii) a stable cubic AlSb phase. In-situ XRD analysis of these films show the AlSb phase crystalizes at a much higher temperature as compared to the A7 phase after annealing of the film to 650 °C. Mushroom cell structures formed with Al-Sb alloys on 120 nm TiN heater show a phase change material resistance switching behavior with reset/set resistance ratio >1000 under pulse measurements. TEM and in situ synchrotron XRD studies indicate fine nucleation grain sizes of ∼8–10 nm, and low elemental redistribution that is useful for improving reliability of the devices. These results indicate that Te-free Al-Sb binary alloys are possible candidates for analog PCM applications.