Guy M. Cohen
Research Subjects
Guy M. Cohen has a total of 57 co-authors. Here are the top co-authors by number of shared publications:
- Christian Lavoie
Conservation International Arlington Virginia USA
2 shared publications - Kevin Brew
IBM AI Hardware Center 2 , Albany, New York 12222
2 shared publications - Michael Yakimov
University at Albany 1 , Albany, New York 12222
2 shared publications - Nathaniel C. Cady
Department of Nanoscale Science & Engineering, University at Albany, Albany, NY, USA
2 shared publications - Rubab Ume
University at Albany 1 , Albany, New York 12222
2 shared publications - Serge Oktyabrsky
College of Nanotechnology, Science and Engineering, University at Albany, Albany, NY 12203, USA
2 shared publications
Latest Publications
- Open Access
- 1 November 2025
- Published by AIP Publishing in AIP Advances
- Vol. 15 (11)
Nanoscale phase separation in Al0.4–Sb0.6 alloy for phase change memory applications
Phase change memory (PCM) is considered an enabling technology for non-volatile multilevel data storage and neuromorphic computing. Recent advancements in PCM have highlighted the need to improve resistance drift and energy efficiency. At present, binary alloys that phase-separate upon crystallization offer a promising solution. The Al–Sb binary alloy crystallizes into a rhombohedral Sb-rich phase and a cubic AlSb phase, with the latter having a higher melting temperature that enables selective melting of the Sb-rich phase for partial RESET programming. Continuum resistance states result from a reversible alloying process, in which programming pulses modulate the granularity and aluminum content of the amorphous Sb-rich phase. Al0.4–Sb0.6 PCM cells, fabricated on Si-foundry templates, exhibit a high resistance contrast of up to 4000× between fully amorphous and crystalline states, along with a low resistance drift coefficient (∼0.06). The high melting point of AlSb also leads to nanoscale compositional heterogeneity, which persists in the amorphous state, suppressing structural relaxation and thus reducing resistance drift. These findings position Al0.4–Sb0.6 as a promising material for engineering multilevel PCM cells based on phase-separating alloys.
- 1 November 2025
- Published by AIP Publishing in AIP Advances
- Vol. 15 (11)
Open AccessNanoscale phase separation in Al0.4–Sb0.6 alloy for phase change memory applications
Phase change memory (PCM) is considered an enabling technology for non-volatile multilevel data storage and neuromorphic computing. Recent advancements in PCM have highlighted the need to improve resistance drift and energy efficiency. At present, binary alloys that phase-separate upon crystallization offer a promising solution. The Al–Sb binary alloy crystallizes into a rhombohedral Sb-rich phase and a cubic AlSb phase, with the latter having a higher melting temperature that enables selective melting of the Sb-rich phase for partial RESET programming. Continuum resistance states result from a reversible alloying process, in which programming pulses modulate the granularity and aluminum content of the amorphous Sb-rich phase. Al0.4–Sb0.6 PCM cells, fabricated on Si-foundry templates, exhibit a high resistance contrast of up to 4000× between fully amorphous and crystalline states, along with a low resistance drift coefficient (∼0.06). The high melting point of AlSb also leads to nanoscale compositional heterogeneity, which persists in the amorphous state, suppressing structural relaxation and thus reducing resistance drift. These findings position Al0.4–Sb0.6 as a promising material for engineering multilevel PCM cells based on phase-separating alloys.
- 16 June 2024
- Published by Wiley in Physica Status Solidi (RRL) – Rapid Research Letters
- Vol. 18 (10)
Low RESET Current Mushroom‐Cell Phase‐Change Memory Using Fiber‐Textured Homostructure GeSbTe on Highly Oriented Seed Layer
Herein, a low RESET current 1T1R mushroom‐cell phase‐change memory (PCM) device that uses fiber‐textured homostructure GeSbTe (GST) grown on highly oriented TiTe2 seed layer is reported. The homostructure device outperformed the industry standard device, that uses doped polycrystalline GST, on most figures of merit. The homostructure devices are also benchmarked against superlattice (SL) PCM devices with 10 periods of 5/5 nm GST/Sb2Te3 grown on the TiTe2 seed layer, and are found to have same low RESET current. It is also observed by transmission electron microscopy that the alternating layers of GST/Sb2Te3 and TiTe2/Sb2Te3 in SL devices are intermixed in the switched region after the devices are cycled with RESET/SET pulses. Additionally, when the SL device is left in the SET state, the intermixed switched region crystallinity is textured and exhibits van der Waals gaps. The SL PCM devices require a precise layered structure that is hard to yield on a full wafer scale. In contrast, fiber‐textured homostructure PCM cells reported here are easily manufacturable, while providing similarly low RESET current and low‐resistance drift, which makes this device suitable for analog artificial intelligence computation.
- 16 June 2024
- Published by Wiley in Physica Status Solidi (RRL) – Rapid Research Letters
- Vol. 18 (10)
Low RESET Current Mushroom‐Cell Phase‐Change Memory Using Fiber‐Textured Homostructure GeSbTe on Highly Oriented Seed Layer
Herein, a low RESET current 1T1R mushroom‐cell phase‐change memory (PCM) device that uses fiber‐textured homostructure GeSbTe (GST) grown on highly oriented TiTe2 seed layer is reported. The homostructure device outperformed the industry standard device, that uses doped polycrystalline GST, on most figures of merit. The homostructure devices are also benchmarked against superlattice (SL) PCM devices with 10 periods of 5/5 nm GST/Sb2Te3 grown on the TiTe2 seed layer, and are found to have same low RESET current. It is also observed by transmission electron microscopy that the alternating layers of GST/Sb2Te3 and TiTe2/Sb2Te3 in SL devices are intermixed in the switched region after the devices are cycled with RESET/SET pulses. Additionally, when the SL device is left in the SET state, the intermixed switched region crystallinity is textured and exhibits van der Waals gaps. The SL PCM devices require a precise layered structure that is hard to yield on a full wafer scale. In contrast, fiber‐textured homostructure PCM cells reported here are easily manufacturable, while providing similarly low RESET current and low‐resistance drift, which makes this device suitable for analog artificial intelligence computation.
- 22 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 70 (7) , 3511-3516
Three Programming States in Bilayer Ga–Sb Phase Change Memory With AlO x Diffusion Barrier
Tellurium-free antimony-based phase change memory (PCM) alloys have attracted much attention due to their superior attributes such as fast switching speed, wide resistance window, and low drift. However, programming reproducible intermediate states in such PCM materials has been challenging. In this study, bilayer PCM cells comprised of Ga–Sb films with two different compositions separated by a 1-nm-thick AlO x diffusion barrier layer were fabricated on Si foundry templates with a Ø120-nm TiN heater and TaN top contact. The current–voltage measurements of the cells exhibit two threshold voltages, separating three stable resistance regions. These cells can be controllably switched among three resistance states, that is, the SET ( $\sim 10^{3} \ \Omega)$ , intermediate ( $\sim 10^{4} \ \Omega)$ , and RESET states ( $\sim 5\times 10^{5}\,\,\ \Omega {)}$ . The phase transitions during switching among three resistance states are discussed and correlated with the device resistance profiles. The stability of the AlO x barrier layer is investigated with transmission electron microscopy (TEM) and energy-dispersive X-ray spectroscopy (EDS).
- 22 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 70 (7) , 3511-3516
Three Programming States in Bilayer Ga–Sb Phase Change Memory With AlO x Diffusion Barrier
Tellurium-free antimony-based phase change memory (PCM) alloys have attracted much attention due to their superior attributes such as fast switching speed, wide resistance window, and low drift. However, programming reproducible intermediate states in such PCM materials has been challenging. In this study, bilayer PCM cells comprised of Ga–Sb films with two different compositions separated by a 1-nm-thick AlO x diffusion barrier layer were fabricated on Si foundry templates with a Ø120-nm TiN heater and TaN top contact. The current–voltage measurements of the cells exhibit two threshold voltages, separating three stable resistance regions. These cells can be controllably switched among three resistance states, that is, the SET ( $\sim 10^{3} \ \Omega)$ , intermediate ( $\sim 10^{4} \ \Omega)$ , and RESET states ( $\sim 5\times 10^{5}\,\,\ \Omega {)}$ . The phase transitions during switching among three resistance states are discussed and correlated with the device resistance profiles. The stability of the AlO x barrier layer is investigated with transmission electron microscopy (TEM) and energy-dispersive X-ray spectroscopy (EDS).
- 1 June 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 15483770,p. 269-272
Gate-all-around silicon nanowire MOSFETs and circuits
We demonstrate undoped-body, gate-all-around (GAA) Si nanowire (NW) MOSFETs with excellent electrostatic scaling. These NW devices, with a TaN/Hf-based gate stack, have high drive-current performance with NFET/PFET I DSAT = 825/950 μA/μm (circumference-normalized) or 2592/2985 μA/μm (diameter-normalized) at supply voltage V DD = 1 V and off-current I OFF = 15 nA/μm. Superior NW uniformity is obtained through the use of a combined hydrogen annealing and oxidation process. Clear scaling of short-channel effects versus NW size is observed. Additionally, we observe a divergence of the nanowire capacitance from the planar limit, as expected, as well as enhanced device self-heating for smaller diameter nanowires. We have also applied this method to making functional 25-stage ring oscillator circuits.
- 1 June 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 15483770,p. 269-272
Gate-all-around silicon nanowire MOSFETs and circuits
We demonstrate undoped-body, gate-all-around (GAA) Si nanowire (NW) MOSFETs with excellent electrostatic scaling. These NW devices, with a TaN/Hf-based gate stack, have high drive-current performance with NFET/PFET I DSAT = 825/950 μA/μm (circumference-normalized) or 2592/2985 μA/μm (diameter-normalized) at supply voltage V DD = 1 V and off-current I OFF = 15 nA/μm. Superior NW uniformity is obtained through the use of a combined hydrogen annealing and oxidation process. Clear scaling of short-channel effects versus NW size is observed. Additionally, we observe a divergence of the nanowire capacitance from the planar limit, as expected, as well as enhanced device self-heating for smaller diameter nanowires. We have also applied this method to making functional 25-stage ring oscillator circuits.
- 1 January 2010
- Published by Springer Nature in MRS Proceedings
- Vol. 1251
Amorphization of Crystalline Phase Change Material by Ion Implantation
- 1 January 2010
- Published by Springer Nature in MRS Proceedings
- Vol. 1251
Amorphization of Crystalline Phase Change Material by Ion Implantation
- 1 January 2003
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 63-66
Package design and measurement of 10 Gbps laser diode on high-speed silicon optical bench
In this paper the electrical package design for a 10 Gbps laser diode on a silicon optical bench will be presented. Specifically the wideband impedance matching is addressed. Simulated data will be compared to measurements.
- 1 January 2003
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 63-66
Package design and measurement of 10 Gbps laser diode on high-speed silicon optical bench
In this paper the electrical package design for a 10 Gbps laser diode on a silicon optical bench will be presented. Specifically the wideband impedance matching is addressed. Simulated data will be compared to measurements.