Ryan J. Mᶜglen
Ryan J. Mᶜglen has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- David A. Reay
School of Engineering, Newcastle University, Newcastle upon Tyne NE1 7RU, UK
2 shared publications - Joshua Ireland
WMG, University of Warwick, Coventry CV47AL, UK
2 shared publications - Pawel Szymanski
Faculty of Mechanical Engineering and Ship Technology, Institute of Energy, Gdańsk University of Technology, Narutowicza St. 11/12, 80-233 Gdańsk, Poland
2 shared publications - Richard Law
School of Engineering, Newcastle University, Newcastle upon Tyne NE1 7RU, UK
2 shared publications - Dinh Quang Truong
Warwick Manufacturing Group (WMG), University of Warwick, Coventry CV4 7AL, UK
1 shared publication James Marco
1 shared publication
Latest Publications
- Open Access
- 21 August 2025
- Published by Elsevier in Journal of Power Sources
- Vol. 657
Effect of cylindrical cell tab architecture on global external temperature distribution using optical fibre temperature measurement
- 21 August 2025
- Published by Elsevier in Journal of Power Sources
- Vol. 657
Open AccessEffect of cylindrical cell tab architecture on global external temperature distribution using optical fibre temperature measurement
- Open Access
An Investigation into the Insertion of a Solid Mandrel into a Commercial Cylindrical Li-Ion Cell for Improved Thermal Performance
Cylindrical Li-ion cells have found utilisation in numerous industries, but they are susceptible to thermal issues, and so they require suitable thermal management. One of the conceptual methods for addressing this issue is the introduction of a metallic mandrel inserted axially through the cell’s central cavity, which has previously been shown to have a thermal benefit through simulation, thermal emulation, and experimentally through bespoke functional test cells. This work has demonstrated the potential ability to modify a commercial LGM50 21700 cell to accept a 2 mm solid metal mandrel whilst maintaining functionality, and then to quantify the thermal behaviour under representative real-world operating conditions. The modification to external geometry is believed to have reduced the effective cooling area, and therefore leads to a temperature increase of 1–5.2 °C on the mandrel cell. The pristine reference cell then underwent the same external geometry modification, which showed no consistent thermal benefit compared to the mandrel cell, which was then validated through simulation. The simulated model evaluated the additional thermal resistances introduced by the modification process and highlighted the potential benefits of using a bespoke cell housing with an integrated mandrel over mandrel insertion. This was more significant under higher current loads, with a 7.2 °C maximum temperature reduction for the bespoke cell housing during a 3 C discharge.
Open AccessAn Investigation into the Insertion of a Solid Mandrel into a Commercial Cylindrical Li-Ion Cell for Improved Thermal Performance
Cylindrical Li-ion cells have found utilisation in numerous industries, but they are susceptible to thermal issues, and so they require suitable thermal management. One of the conceptual methods for addressing this issue is the introduction of a metallic mandrel inserted axially through the cell’s central cavity, which has previously been shown to have a thermal benefit through simulation, thermal emulation, and experimentally through bespoke functional test cells. This work has demonstrated the potential ability to modify a commercial LGM50 21700 cell to accept a 2 mm solid metal mandrel whilst maintaining functionality, and then to quantify the thermal behaviour under representative real-world operating conditions. The modification to external geometry is believed to have reduced the effective cooling area, and therefore leads to a temperature increase of 1–5.2 °C on the mandrel cell. The pristine reference cell then underwent the same external geometry modification, which showed no consistent thermal benefit compared to the mandrel cell, which was then validated through simulation. The simulated model evaluated the additional thermal resistances introduced by the modification process and highlighted the potential benefits of using a bespoke cell housing with an integrated mandrel over mandrel insertion. This was more significant under higher current loads, with a 7.2 °C maximum temperature reduction for the bespoke cell housing during a 3 C discharge.
- Open Access
Correction: Szymanski et al. Recent Advances in Loop Heat Pipes with Flat Evaporator. Entropy 2021, 23, 1374
The author of the original publication
Open AccessCorrection: Szymanski et al. Recent Advances in Loop Heat Pipes with Flat Evaporator. Entropy 2021, 23, 1374
The author of the original publication
- Open Access
Recent Advances in Loop Heat Pipes with Flat Evaporator
The focus of this review is to present the current advances in Loop Heat Pipes (LHP) with flat evaporators, which address the current challenges to the wide implementation of the technology. A recent advance in LHP is the design of flat-shaped evaporators, which is better suited to the geometry of discretely mounted electronics components (microprocessors) and therefore negate the need for an additional transfer surface (saddle) between component and evaporator. However, various challenges exist in the implementation of flat-evaporator, including (1) deformation of the evaporator due to high internal pressure and uneven stress distribution in the non-circular casing; (2) heat leak from evaporator heating zone and sidewall into the compensation chamber; (3) poor performance at start-up; (4) reverse flow through the wick; or (5) difficulties in sealing, and hence frequent leakage. This paper presents and reviews state-of-the-art LHP technologies; this includes an (a) review of novel manufacturing methods; (b) LHP evaporator designs; (c) working fluids; and (d) construction materials. The work presents solutions that are used to develop or improve the LHP construction, overall thermal performance, heat transfer distance, start-up time (especially at low heat loads), manufacturing cost, weight, possibilities of miniaturization and how they affect the solution on the above-presented problems and challenges in flat shape LHP development to take advantage in the passive cooling systems for electronic devices in multiple applications.
Open AccessRecent Advances in Loop Heat Pipes with Flat Evaporator
The focus of this review is to present the current advances in Loop Heat Pipes (LHP) with flat evaporators, which address the current challenges to the wide implementation of the technology. A recent advance in LHP is the design of flat-shaped evaporators, which is better suited to the geometry of discretely mounted electronics components (microprocessors) and therefore negate the need for an additional transfer surface (saddle) between component and evaporator. However, various challenges exist in the implementation of flat-evaporator, including (1) deformation of the evaporator due to high internal pressure and uneven stress distribution in the non-circular casing; (2) heat leak from evaporator heating zone and sidewall into the compensation chamber; (3) poor performance at start-up; (4) reverse flow through the wick; or (5) difficulties in sealing, and hence frequent leakage. This paper presents and reviews state-of-the-art LHP technologies; this includes an (a) review of novel manufacturing methods; (b) LHP evaporator designs; (c) working fluids; and (d) construction materials. The work presents solutions that are used to develop or improve the LHP construction, overall thermal performance, heat transfer distance, start-up time (especially at low heat loads), manufacturing cost, weight, possibilities of miniaturization and how they affect the solution on the above-presented problems and challenges in flat shape LHP development to take advantage in the passive cooling systems for electronic devices in multiple applications.