Pawel Szymanski
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Pawel Szymanski has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Dariusz Mikielewicz
Gdansk University of Technology
4 shared publications - Mateusz Boćko
Faculty of Mechanical Engineering and Ship Technology, Institute of Energy, Gdańsk University of Technology, Narutowicza St. 11/12, 80-233 Gdańsk, Poland
3 shared publications - David A. Reay
School of Engineering, Newcastle University, Newcastle upon Tyne NE1 7RU, UK
2 shared publications - Richard Law
School of Engineering, Newcastle University, Newcastle upon Tyne NE1 7RU, UK
2 shared publications - Ryan J. Mᶜglen
Aavid, Thermal Division of Boyd Corporation, Ashington NE63 8QW, UK
2 shared publications - Charles Pelle
Faculty of Mechanical Engineering and Ship Technology, Gdańsk University of Technology, 80-233 Gdańsk, Poland
1 shared publication
Latest Publications
- Open Access
Influence of Gravitational Orientation on the Formation of Electrodeposited Copper Wicks
Porous wicks ensure capillary liquid transport in heat pipes and vapour chambers. Manufacturing them through electrochemical deposition is a promising method that yields competitive results. The gravitational orientation during electrochemical deposition, however, has rarely been taken into consideration. In this study, the effect of deposition orientation relative to gravity on the capillary performance of electrodeposited copper wicks was investigated. In total, 24 samples were prepared in three configurations defined by the angle between the cathode surface normal and gravitational acceleration: Top (22.8°, downward-facing), Vertical (90°, sideways-facing), and Bottom (157.2°, upward-facing). All other electrodeposition conditions were kept identical. Capillary performance was evaluated for 5 samples per configuration using a capillary lift rate test. The Top configuration achieved up to 44.8% greater mean capillary lift height than the Bottom configuration after 5 s. The Bottom and Vertical configurations exhibited similar capillary rise behaviour, whereas Top samples reached 15 mm in 19.4 s, compared with 42.9 s and 41.4 s for the Bottom and Vertical configurations, respectively. These results suggest that gravitational orientation affects the capillary performance of electrodeposited copper wicks and should be considered during their fabrication.
Open AccessInfluence of Gravitational Orientation on the Formation of Electrodeposited Copper Wicks
Porous wicks ensure capillary liquid transport in heat pipes and vapour chambers. Manufacturing them through electrochemical deposition is a promising method that yields competitive results. The gravitational orientation during electrochemical deposition, however, has rarely been taken into consideration. In this study, the effect of deposition orientation relative to gravity on the capillary performance of electrodeposited copper wicks was investigated. In total, 24 samples were prepared in three configurations defined by the angle between the cathode surface normal and gravitational acceleration: Top (22.8°, downward-facing), Vertical (90°, sideways-facing), and Bottom (157.2°, upward-facing). All other electrodeposition conditions were kept identical. Capillary performance was evaluated for 5 samples per configuration using a capillary lift rate test. The Top configuration achieved up to 44.8% greater mean capillary lift height than the Bottom configuration after 5 s. The Bottom and Vertical configurations exhibited similar capillary rise behaviour, whereas Top samples reached 15 mm in 19.4 s, compared with 42.9 s and 41.4 s for the Bottom and Vertical configurations, respectively. These results suggest that gravitational orientation affects the capillary performance of electrodeposited copper wicks and should be considered during their fabrication.
- Open Access
- 16 October 2026
- Published by MDPI AG in Electronics
- Vol. 15 (20) , 4785
Enthalpy–Temperature Characterisation of Organic Phase Change Materials Using a Common T-History Framework
Phase change materials can exhibit markedly different thermal responses during cooling, ranging from narrow single-stage transitions to broad or multistage behaviour, which requires the analysis procedure to account for differences in response structure. This study applies a common water-referenced T-history framework to the enthalpy–temperature characterisation of six organic phase change materials: RT35HC, RT45HC, lauric acid, beeswax, palmitic acid and soy wax. Five experiments were reported for each material. The enthalpy was obtained from small, matched temperature intervals in the same way for every material, while the low-temperature calorimetric boundary was derived from the measured cooling response rather than imposed as a fixed temperature criterion. Thermal responses were described by cumulative temperatures at the 5%, 50% and 95% levels of the detected thermal effect. The T-history enthalpy changes were 207.35 ± 32.31, 197.59 ± 23.31, 224.11 ± 32.48, 200.38 ± 17.47, 191.50 ± 15.16 and 109.37 ± 13.33 J/g for RT35HC, RT45HC, lauric acid, beeswax, palmitic acid and soy wax, respectively. Comparison with differential scanning calorimetry measurements of the tested samples, independent calorimetric studies, manufacturer data and published thermal data supported the identified temperature regions and response structures. The enthalpy values were interpreted separately, taking into account differences in calorimetric definitions and temperature intervals. Changing the detector settings changed the mean primary midpoint temperature by less than 0.03 K for every material, while changing the matched temperature interval from the nominal 0.250 K to 0.125 K or 0.500 K changed the mean enthalpy by at most 2.29%. The results show that a common T-history framework can characterise substantially different cooling behaviours of the phase change materials when calorimetric boundaries are derived from the measured thermal response. The resulting characteristics also provide material-level information relevant to the selection of PCMs for electronic thermal management applications.
- 16 October 2026
- Published by MDPI AG in Electronics
- Vol. 15 (20) , 4785
Open AccessEnthalpy–Temperature Characterisation of Organic Phase Change Materials Using a Common T-History Framework
Phase change materials can exhibit markedly different thermal responses during cooling, ranging from narrow single-stage transitions to broad or multistage behaviour, which requires the analysis procedure to account for differences in response structure. This study applies a common water-referenced T-history framework to the enthalpy–temperature characterisation of six organic phase change materials: RT35HC, RT45HC, lauric acid, beeswax, palmitic acid and soy wax. Five experiments were reported for each material. The enthalpy was obtained from small, matched temperature intervals in the same way for every material, while the low-temperature calorimetric boundary was derived from the measured cooling response rather than imposed as a fixed temperature criterion. Thermal responses were described by cumulative temperatures at the 5%, 50% and 95% levels of the detected thermal effect. The T-history enthalpy changes were 207.35 ± 32.31, 197.59 ± 23.31, 224.11 ± 32.48, 200.38 ± 17.47, 191.50 ± 15.16 and 109.37 ± 13.33 J/g for RT35HC, RT45HC, lauric acid, beeswax, palmitic acid and soy wax, respectively. Comparison with differential scanning calorimetry measurements of the tested samples, independent calorimetric studies, manufacturer data and published thermal data supported the identified temperature regions and response structures. The enthalpy values were interpreted separately, taking into account differences in calorimetric definitions and temperature intervals. Changing the detector settings changed the mean primary midpoint temperature by less than 0.03 K for every material, while changing the matched temperature interval from the nominal 0.250 K to 0.125 K or 0.500 K changed the mean enthalpy by at most 2.29%. The results show that a common T-history framework can characterise substantially different cooling behaviours of the phase change materials when calorimetric boundaries are derived from the measured thermal response. The resulting characteristics also provide material-level information relevant to the selection of PCMs for electronic thermal management applications.
- 5 March 2026
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 151 (7) , 5745-5765
Multi-nodal analytical thermal analysis algorithm for an Earth-pointing CubeSat in low Earth orbit
- 5 March 2026
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 151 (7) , 5745-5765
Multi-nodal analytical thermal analysis algorithm for an Earth-pointing CubeSat in low Earth orbit
- Open Access
- 27 February 2026
- Published by MDPI AG in Electronics
- Vol. 15 (5) , 976
Experimental Investigation of Heat Pipe-Assisted Cooling for Heat Creep Mitigation in FFF Extruders
Heat creep is a critical failure mechanism in fused filament fabrication (FFF) extrusion systems, arising from insufficient thermal isolation between the hot end and cold end. It causes premature polymer softening, extrusion instability, and nozzle clogging, especially when active cooling is reduced or lost. This study experimentally evaluates passive cooling strategies for mitigating heat creep in consumer-class printers by exploiting ambient thermal stratification within the build volume. Vertical air-temperature gradients above heated build plates were measured for enclosed, semi-enclosed, and open-frame architectures, revealing pronounced stratification. Cold-end temperatures were then quantified for a stock extruder under forced and natural convection while printing polylactic acid (PLA) and acrylonitrile butadiene styrene (ABS). Finally, a modified cold-end using a heat pipe to relocate heat rejection to an elevated heat sink was tested under identical conditions, assuming fan failure. Elevated heat-rejection locations experienced lower ambient temperatures and improved natural-convection heat transfer. Relative to the stock configuration, the augmented design reduced cold-end temperatures and improved thermal stability during representative printing cycles without continuous active cooling—the improvement percent is ~8%. The results demonstrate that coupling heat-pipe conduction with environmental thermal gradients can mitigate heat creep and improve extruder reliability with lower energy demand.
- 27 February 2026
- Published by MDPI AG in Electronics
- Vol. 15 (5) , 976
Open AccessExperimental Investigation of Heat Pipe-Assisted Cooling for Heat Creep Mitigation in FFF Extruders
Heat creep is a critical failure mechanism in fused filament fabrication (FFF) extrusion systems, arising from insufficient thermal isolation between the hot end and cold end. It causes premature polymer softening, extrusion instability, and nozzle clogging, especially when active cooling is reduced or lost. This study experimentally evaluates passive cooling strategies for mitigating heat creep in consumer-class printers by exploiting ambient thermal stratification within the build volume. Vertical air-temperature gradients above heated build plates were measured for enclosed, semi-enclosed, and open-frame architectures, revealing pronounced stratification. Cold-end temperatures were then quantified for a stock extruder under forced and natural convection while printing polylactic acid (PLA) and acrylonitrile butadiene styrene (ABS). Finally, a modified cold-end using a heat pipe to relocate heat rejection to an elevated heat sink was tested under identical conditions, assuming fan failure. Elevated heat-rejection locations experienced lower ambient temperatures and improved natural-convection heat transfer. Relative to the stock configuration, the augmented design reduced cold-end temperatures and improved thermal stability during representative printing cycles without continuous active cooling—the improvement percent is ~8%. The results demonstrate that coupling heat-pipe conduction with environmental thermal gradients can mitigate heat creep and improve extruder reliability with lower energy demand.
- Open Access
Analysis of Key Material Parameters of Evaporator Wicks and Working Fluids for a Loop Heat Pipe Operating in the Temperature Range of 500–700 K
This study presents a preliminary evaluation of candidate wick material and working fluid for a flat-loop heat pipe (F-LHP) designed to operate within the temperature range of 500–700 K. The selection process considered key thermal and physical parameters, including thermal conductivity, chemical compatibility between wick and fluid, capillary pressure generation, pressure drop across the wick structure, and structural integrity at elevated temperatures. A range of metallic and ceramic wick materials, along with suitable high-temperature working fluids, were reviewed and compared based on performance metrics and practical availability. Special attention was given to oxidation and corrosion resistance, capillary performance, and thermal stability under elevated-temperature conditions. Nine different porous wicks with distinct materials and microstructures—differing in pore size, porosity, and permeability—were analyzed in combination with seven different working fluids. The analysis focused on determining which combinations generated the highest capillary pressure and which exhibited the lowest flow resistance due to external flow, thereby enhancing the LHP’s performance. Based on these results, the study identifies the most effective wick–fluid pairings for F-LHP applications, offering an optimal balance of thermal performance and long-term reliability. These findings provide a foundation for further experimental validation and the development of prototypes.
Open AccessAnalysis of Key Material Parameters of Evaporator Wicks and Working Fluids for a Loop Heat Pipe Operating in the Temperature Range of 500–700 K
This study presents a preliminary evaluation of candidate wick material and working fluid for a flat-loop heat pipe (F-LHP) designed to operate within the temperature range of 500–700 K. The selection process considered key thermal and physical parameters, including thermal conductivity, chemical compatibility between wick and fluid, capillary pressure generation, pressure drop across the wick structure, and structural integrity at elevated temperatures. A range of metallic and ceramic wick materials, along with suitable high-temperature working fluids, were reviewed and compared based on performance metrics and practical availability. Special attention was given to oxidation and corrosion resistance, capillary performance, and thermal stability under elevated-temperature conditions. Nine different porous wicks with distinct materials and microstructures—differing in pore size, porosity, and permeability—were analyzed in combination with seven different working fluids. The analysis focused on determining which combinations generated the highest capillary pressure and which exhibited the lowest flow resistance due to external flow, thereby enhancing the LHP’s performance. Based on these results, the study identifies the most effective wick–fluid pairings for F-LHP applications, offering an optimal balance of thermal performance and long-term reliability. These findings provide a foundation for further experimental validation and the development of prototypes.
- 18 January 2024
- Published by Wiley in Advanced Engineering Materials
- Vol. 26 (6)
Beeswax and Palmitic Acid Utilization with Heat Pipes for Electronics Cooling
This article presents an experimental study of heat pipes supported by phase‐change materials (PCMs) coated at their adiabatic sections in application for electronics cooling. The PCMs investigated in this research are palmitic acid and beeswax, the latter being considered as a more cost‐effective alternative. The study focuses on three powers: 20, 25, and 30 W. The experimental results reveal that the incorporation of palmitic acid as a PCM leads to a reduction in component's maximum temperature by 13.3%, 12.6%, and 11.8% for the respective powers. Utilization of beeswax results in temperature reductions of 5%, 5.2%, and 8.4%. Notably, for higher heat flux conditions, the influence of beeswax on temperature control is comparable to that of palmitic acid. Furthermore, beeswax demonstrates a significantly higher capability to mitigate temperature decrease during cooldown, serving as a superior measure against overcooling. Moreover, during the thermal cycling scenario considered in this study, beeswax reduces the peak‐valley temperature by 25%, while palmitic acid achieves a reduction of 14.6%. These findings suggest that beeswax has the potential to serve as an alternative to traditional organic PCMs in electronics cooling applications that utilize heat pipes.
- 18 January 2024
- Published by Wiley in Advanced Engineering Materials
- Vol. 26 (6)
Beeswax and Palmitic Acid Utilization with Heat Pipes for Electronics Cooling
This article presents an experimental study of heat pipes supported by phase‐change materials (PCMs) coated at their adiabatic sections in application for electronics cooling. The PCMs investigated in this research are palmitic acid and beeswax, the latter being considered as a more cost‐effective alternative. The study focuses on three powers: 20, 25, and 30 W. The experimental results reveal that the incorporation of palmitic acid as a PCM leads to a reduction in component's maximum temperature by 13.3%, 12.6%, and 11.8% for the respective powers. Utilization of beeswax results in temperature reductions of 5%, 5.2%, and 8.4%. Notably, for higher heat flux conditions, the influence of beeswax on temperature control is comparable to that of palmitic acid. Furthermore, beeswax demonstrates a significantly higher capability to mitigate temperature decrease during cooldown, serving as a superior measure against overcooling. Moreover, during the thermal cycling scenario considered in this study, beeswax reduces the peak‐valley temperature by 25%, while palmitic acid achieves a reduction of 14.6%. These findings suggest that beeswax has the potential to serve as an alternative to traditional organic PCMs in electronics cooling applications that utilize heat pipes.
- Open Access
- 20 July 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (14) , 8415
The In-House Method of Manufacturing a Low-Cost Heat Pipe with Specified Thermophysical Properties and Geometry
Various types of heat pipes are available to purchase off the shelf, from various manufacturers, but most of them have strictly defined geometry and technical parameters. However, when there is a need to use a heat pipe (HP) with an unusual size and shape or working conditions other than the standard ones, it becomes very costly to order them from manufacturers, especially in small quantities, and only a few producers are willing to fulfill such an order. This paper presents a detailed description and step-by-step method of manufacturing and testing a low-cost HP with specific properties and geometry, cooperating with a modular heat recovery system based on the use of phase change materials (PCM) for electromobility applications. The presented heat pipes were made entirely by hand, primarily with the use of basic workshop tools, without the use of specialized and automated CNC machines. Utensils used during the process were either made by hand or using desktop FDM 3D printers. During the evaluation of heat pipes’ performance within PCM (coconut oil), simple statistical functions were used. One-dimensional and two-dimensional histograms were used to visualize data obtained during this research. The presented method allows the manufacturing of heat pipes that are, on average, able to melt about 35% more PCM than an empty copper pipe with the exact same geometry. The HPs’ performance in coconut oil was evaluated on the basis of their future applications.
- 20 July 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (14) , 8415
Open AccessThe In-House Method of Manufacturing a Low-Cost Heat Pipe with Specified Thermophysical Properties and Geometry
Various types of heat pipes are available to purchase off the shelf, from various manufacturers, but most of them have strictly defined geometry and technical parameters. However, when there is a need to use a heat pipe (HP) with an unusual size and shape or working conditions other than the standard ones, it becomes very costly to order them from manufacturers, especially in small quantities, and only a few producers are willing to fulfill such an order. This paper presents a detailed description and step-by-step method of manufacturing and testing a low-cost HP with specific properties and geometry, cooperating with a modular heat recovery system based on the use of phase change materials (PCM) for electromobility applications. The presented heat pipes were made entirely by hand, primarily with the use of basic workshop tools, without the use of specialized and automated CNC machines. Utensils used during the process were either made by hand or using desktop FDM 3D printers. During the evaluation of heat pipes’ performance within PCM (coconut oil), simple statistical functions were used. One-dimensional and two-dimensional histograms were used to visualize data obtained during this research. The presented method allows the manufacturing of heat pipes that are, on average, able to melt about 35% more PCM than an empty copper pipe with the exact same geometry. The HPs’ performance in coconut oil was evaluated on the basis of their future applications.
- Open Access
Current Trends in Wick Structure Construction in Loop Heat Pipes Applications: A Review
Thermal control systems have been introduced as an important part of electronic devices, enabling thermal management of their electronic components. Loop heat pipe (LHP) is a passive two-phase heat transfer device with significant potential for numerous applications, such as aerospace applications, high-power LEDs, and solar central receivers. Its advantages are high heat transfer capability, low thermal resistance, long-distance heat transfer, and compact structure. The essential role of wick structures on the performance of LHPs has already been highlighted, but no comprehensive review is available that deals with different parameters such as LHP design and wick size, which are largely decisive and effective in achieving a practical level of thermal transmission governed by wick structures. To rely on this necessity, this article summarizes, analyzes, and classifies advancements in the design and fabrication of wick structures. The main conclusion to be drawn after careful monitoring and weighing of the related literature is that LHPs with composites and additively manufactured wicks show a higher heat transfer coefficient than other conventional structures. Indeed, future works should be focused on the design of more structurally efficient wicks, which may allow us to optimize materials and geometrical parameters of wick structure for higher heat transfer through LHPs.
Open AccessCurrent Trends in Wick Structure Construction in Loop Heat Pipes Applications: A Review
Thermal control systems have been introduced as an important part of electronic devices, enabling thermal management of their electronic components. Loop heat pipe (LHP) is a passive two-phase heat transfer device with significant potential for numerous applications, such as aerospace applications, high-power LEDs, and solar central receivers. Its advantages are high heat transfer capability, low thermal resistance, long-distance heat transfer, and compact structure. The essential role of wick structures on the performance of LHPs has already been highlighted, but no comprehensive review is available that deals with different parameters such as LHP design and wick size, which are largely decisive and effective in achieving a practical level of thermal transmission governed by wick structures. To rely on this necessity, this article summarizes, analyzes, and classifies advancements in the design and fabrication of wick structures. The main conclusion to be drawn after careful monitoring and weighing of the related literature is that LHPs with composites and additively manufactured wicks show a higher heat transfer coefficient than other conventional structures. Indeed, future works should be focused on the design of more structurally efficient wicks, which may allow us to optimize materials and geometrical parameters of wick structure for higher heat transfer through LHPs.
- Open Access
Additive Manufacturing as a Solution to Challenges Associated with Heat Pipe Production
The aim of this review is to present the recent developments in heat pipe production, which respond to the current technical problems related to the wide implementation of this technology. A novel approach in HP manufacturing is to utilise hi-tech additive manufacturing techniques where the most complicated geometries are fabricated layer-by-layer directly from a digital file. This technology might be a solution to various challenges that exist in HP production, i.e., (1) manufacturing of complex or unusual geometries HPs; (2) manufacturing complicated and efficient homogenous wick structures with desired porosity, uniform pore sizes, permeability, thickness and where the pores are evenly distributed; (3) manufacturing a gravity friendly wick structures; (4) high customisation and production time; (5) high costs; (6) difficulties in the integration of the HP into a unit chassis that enables direct thermal management of heated element and decrease its total thermal resistance; (7) high weight and material use of the part; (8) difficulties in sealing; (9) deformation of the flat shape HPs caused by the high pressure and uneven distribution of stress in the casing, among others.
Open AccessAdditive Manufacturing as a Solution to Challenges Associated with Heat Pipe Production
The aim of this review is to present the recent developments in heat pipe production, which respond to the current technical problems related to the wide implementation of this technology. A novel approach in HP manufacturing is to utilise hi-tech additive manufacturing techniques where the most complicated geometries are fabricated layer-by-layer directly from a digital file. This technology might be a solution to various challenges that exist in HP production, i.e., (1) manufacturing of complex or unusual geometries HPs; (2) manufacturing complicated and efficient homogenous wick structures with desired porosity, uniform pore sizes, permeability, thickness and where the pores are evenly distributed; (3) manufacturing a gravity friendly wick structures; (4) high customisation and production time; (5) high costs; (6) difficulties in the integration of the HP into a unit chassis that enables direct thermal management of heated element and decrease its total thermal resistance; (7) high weight and material use of the part; (8) difficulties in sealing; (9) deformation of the flat shape HPs caused by the high pressure and uneven distribution of stress in the casing, among others.
- Open Access
Correction: Szymanski et al. Recent Advances in Loop Heat Pipes with Flat Evaporator. Entropy 2021, 23, 1374
The author of the original publication
Open AccessCorrection: Szymanski et al. Recent Advances in Loop Heat Pipes with Flat Evaporator. Entropy 2021, 23, 1374
The author of the original publication