Claudia Diletto
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Claudia Diletto has a total of 54 co-authors. Here are the top co-authors by number of shared publications:
- Finizia Auriemma
Dipartimento di Scienze Chimiche Università di Napoli Federico II, Complesso Monte S. Angelo, Via Cintia, I-80126 Napoli, Italy
5 shared publications - Rocco Di Girolamo
Dipartimento di Scienze Chimiche, Università di Napoli Federico II, Complesso Monte S. Angelo, Via Cintia, I-80126 Napoli, Italy
5 shared publications - Antonio D’angelo
Portici Research Centre, Italian National Agency for New Technologies, Energy and Sustainable Economic Development (ENEA), P.le E. Fermi 1, 80055 Portici, Italy
4 shared publications - Antonio Guglielmo
Portici Research Centre, Italian National Agency for New Technologies, Energy and Sustainable Economic Development (ENEA), P.le E. Fermi 1, 80055 Portici, Italy
4 shared publications - Michela Lanchi
Casaccia Research Centre, Italian National Agency for New Technologies, Energy and Sustainable Economic Development (ENEA), Via Anguillarese 301, 00123 S. Maria di Galeria, Italy
4 shared publications - Pasquale Morvillo
Energy and Sustainable Economic Development (ENEA) – Portici Research Centre Italian National Agency for New Technologies Piazzale E. Fermi 1 Portici (Na) 80055 Italy
4 shared publications
Latest Publications
- Open Access
Solar Selective Absorber Coating with Multilayer Infrared Reflector for Receiver Tubes Operating up to 550 °C
This work presents a modular W/Ag/AlN infrared reflector for solar selective absorber coatings (SSACs) intended for CSP/CST receiver tubes operating under vacuum at 550 °C. Optical analyses showed that AlN deposition preserved Ag infrared reflectance. Two Ag/AlN bilayers reduced the W reflector’s hemispherical emittance from 7.5% to 2.9%, calculated from room-temperature reflectance weighted at 550 °C. The reflector was first integrated into an SSAC for durability assessment. Accelerated aging under vacuum at 620, 650, and 690 °C yielded an Arrhenius activation energy of 497 kJ/mol and predicted an emittance increase of 0.34 percentage points after 25 years at 550 °C (8 h/day). An optimized SSAC subsequently achieved 95.2% solar absorptance and 11.3% hemispherical emittance on stainless steel, based on room-temperature reflectance. Simulations incorporating temperature-dependent optical properties estimated an emittance of 13.4% at 550 °C, versus 14.7% for a W-based coating. The previous Ag-based coating had lower estimated emittance (11.0%) but required three times more Ag. A 96 h aging test at 650 °C showed that the optimized SSAC exhibited an emittance degradation rate comparable to those of the samples of the coating used in the durability study, supporting the long-term stability prediction for the optimized architecture.
Open AccessSolar Selective Absorber Coating with Multilayer Infrared Reflector for Receiver Tubes Operating up to 550 °C
This work presents a modular W/Ag/AlN infrared reflector for solar selective absorber coatings (SSACs) intended for CSP/CST receiver tubes operating under vacuum at 550 °C. Optical analyses showed that AlN deposition preserved Ag infrared reflectance. Two Ag/AlN bilayers reduced the W reflector’s hemispherical emittance from 7.5% to 2.9%, calculated from room-temperature reflectance weighted at 550 °C. The reflector was first integrated into an SSAC for durability assessment. Accelerated aging under vacuum at 620, 650, and 690 °C yielded an Arrhenius activation energy of 497 kJ/mol and predicted an emittance increase of 0.34 percentage points after 25 years at 550 °C (8 h/day). An optimized SSAC subsequently achieved 95.2% solar absorptance and 11.3% hemispherical emittance on stainless steel, based on room-temperature reflectance. Simulations incorporating temperature-dependent optical properties estimated an emittance of 13.4% at 550 °C, versus 14.7% for a W-based coating. The previous Ag-based coating had lower estimated emittance (11.0%) but required three times more Ag. A 96 h aging test at 650 °C showed that the optimized SSAC exhibited an emittance degradation rate comparable to those of the samples of the coating used in the durability study, supporting the long-term stability prediction for the optimized architecture.
- Open Access
Solar Selective Absorber Coating with Ag Infrared Reflector for Receiver Tubes Operating at 550 °C
The present work introduces a new solar selective absorber coating (SSAC) for the receiver tube of Concentrated Solar Power (CSP) systems, proposing silver as an infrared reflector for application at 550 °C. In the past, the Italian National Agency for New Technologies, Energy and Sustainable Economic Development (ENEA) has developed SSACs suitable for applications at 550 °C, featuring solar absorbers based on graded multilayer cermet of WN-AlN and W-Al2O3 and an infrared reflector of tungsten. Although these coatings ensured properly stable photothermal performance at 550 °C, due to the low tungsten diffusivity, their hemispherical emittance could be reduced by using metals with higher reflectance in the infrared region, like silver. However, the high diffusivity of silver compromises its use at high temperatures. This last drawback has been addressed by foreseeing two stabilizing layers enclosing the Ag infrared reflector. One W stabilizing layer was placed between the substrate and the Ag infrared reflector, whereas a second stabilizing layer, selected among aluminum nitride deposited with a low and high nitrogen flow and aluminum oxide deposited at a low oxygen flow, was placed between the Ag infrared reflector and the solar absorber. Accelerated aging tests revealed a negligible (not detectable) degradation of the solar absorptance for the new SSACs. Furthermore, the hemispherical emittance at 550 °C increased by 0.75% and 0.42% for solar coatings with aluminum nitride stabilizing layers deposited through a high and low nitrogen flow, respectively. Differently, the increase was evaluated as being equal to 0.08% for the solar coating with an aluminum oxide stabilizing layer deposited through a low oxygen flow. The manufactured solar coating with a stabilizing layer of aluminum nitride deposited with a low nitrogen flow exhibited a solar absorptance of 95%, comparable to ENEA coatings incorporating a W infrared reflector for applications at 550 °C, whereas the estimated hemispherical emittance at 550 °C was 2% lower than that of the best ENEA coating with a W infrared reflector for the same temperature.
Open AccessSolar Selective Absorber Coating with Ag Infrared Reflector for Receiver Tubes Operating at 550 °C
The present work introduces a new solar selective absorber coating (SSAC) for the receiver tube of Concentrated Solar Power (CSP) systems, proposing silver as an infrared reflector for application at 550 °C. In the past, the Italian National Agency for New Technologies, Energy and Sustainable Economic Development (ENEA) has developed SSACs suitable for applications at 550 °C, featuring solar absorbers based on graded multilayer cermet of WN-AlN and W-Al2O3 and an infrared reflector of tungsten. Although these coatings ensured properly stable photothermal performance at 550 °C, due to the low tungsten diffusivity, their hemispherical emittance could be reduced by using metals with higher reflectance in the infrared region, like silver. However, the high diffusivity of silver compromises its use at high temperatures. This last drawback has been addressed by foreseeing two stabilizing layers enclosing the Ag infrared reflector. One W stabilizing layer was placed between the substrate and the Ag infrared reflector, whereas a second stabilizing layer, selected among aluminum nitride deposited with a low and high nitrogen flow and aluminum oxide deposited at a low oxygen flow, was placed between the Ag infrared reflector and the solar absorber. Accelerated aging tests revealed a negligible (not detectable) degradation of the solar absorptance for the new SSACs. Furthermore, the hemispherical emittance at 550 °C increased by 0.75% and 0.42% for solar coatings with aluminum nitride stabilizing layers deposited through a high and low nitrogen flow, respectively. Differently, the increase was evaluated as being equal to 0.08% for the solar coating with an aluminum oxide stabilizing layer deposited through a low oxygen flow. The manufactured solar coating with a stabilizing layer of aluminum nitride deposited with a low nitrogen flow exhibited a solar absorptance of 95%, comparable to ENEA coatings incorporating a W infrared reflector for applications at 550 °C, whereas the estimated hemispherical emittance at 550 °C was 2% lower than that of the best ENEA coating with a W infrared reflector for the same temperature.
- Open Access
Influence of Process Parameters on Properties of Non-Reactive RF Magnetron-Sputtered Indium Tin Oxide Thin Films Used as Electrodes for Organic Light-Emitting Diodes
Indium tin oxide (ITO) is a transparent conductive oxide (TCO) commonly used in the realization of optoelectronic devices needing at least a transparent electrode. In this work, ITO thin films were deposited on glass substrates by non-reactive RF magnetron sputtering, investigating the effects of power density, sputtering pressure, and substrate temperature on the electrical, optical, and structural properties of the as-grown films. High-quality films, in terms of crystallinity, transparency, and conductivity were obtained. The 120 nm thick ITO films grown at 225 °C under an argon pressure of 6.9 mbar and a sputtering power density of 2.19 W/cm2 without post-annealing treatments in an oxidizing environment showed an optical transmittance near 90% at 550 nm and a resistivity of cm. This material was applied as the electrode of simple-structure organic light-emitting diodes (OLEDs).Open AccessInfluence of Process Parameters on Properties of Non-Reactive RF Magnetron-Sputtered Indium Tin Oxide Thin Films Used as Electrodes for Organic Light-Emitting Diodes
Indium tin oxide (ITO) is a transparent conductive oxide (TCO) commonly used in the realization of optoelectronic devices needing at least a transparent electrode. In this work, ITO thin films were deposited on glass substrates by non-reactive RF magnetron sputtering, investigating the effects of power density, sputtering pressure, and substrate temperature on the electrical, optical, and structural properties of the as-grown films. High-quality films, in terms of crystallinity, transparency, and conductivity were obtained. The 120 nm thick ITO films grown at 225 °C under an argon pressure of 6.9 mbar and a sputtering power density of 2.19 W/cm2 without post-annealing treatments in an oxidizing environment showed an optical transmittance near 90% at 550 nm and a resistivity of cm. This material was applied as the electrode of simple-structure organic light-emitting diodes (OLEDs). - Open Access
- 3 May 2023
- Published by Wiley in Applied Research
- Vol. 3 (2)
New spectrally selective coatings for CSP linear receivers operating in air at high temperature
An attractive candidate to reduce dependence on fossil fuels and replace them by renewable sources is represented by concentrated solar power (CSP) technology, whose wide deployment is still hindered by its high investment costs. In CSP linear collector plants, a key component with high technological content may be identified in receiver tubes, that are traversed by heat transfer fluid and located on focal line on which solar radiation is concentrated by mirrors. The proposed work aims at developing spectrally selective coatings for receiver tubes able to overcome state‐of‐the‐art technological limitation in terms of both vacuum encapsulation and maximum operative temperature, currently limited at 550°C for molten salts CSP plants. To this aim, a multilayer structure was designed and developed for coating a receiver tube to be employed in open‐air environment at temperature of 600°C. The multilayer coating is based on tungsten chromium titanium infrared reflector and includes a solar absorber layer developed with two alternative methods of reactive sputtering and thermal oxidation respectively, finally covered by antireflective and barrier bi‐layer of aluminum oxide and silica. Thermal stability was demonstrated of the new developed coatings, since only small variations were measured of the optical parameters after more than 2000 h of aging in open air conditions at temperature of 600°C (on average less than 5%), with final measured solar absorptance αs of 73% and 87% and thermal emissivity εth at 600°C of 18% and 27% for aged multilayer structures including the absorber layer obtained through thermal oxidation and sputtering process, respectively. These results pave the way for further improvement in terms of both optical performance and operative temperature increase, allowing to enhance efficiency and lower costs, thus contributing to ease to deployment of CSP technology.
- 3 May 2023
- Published by Wiley in Applied Research
- Vol. 3 (2)
Open AccessNew spectrally selective coatings for CSP linear receivers operating in air at high temperature
An attractive candidate to reduce dependence on fossil fuels and replace them by renewable sources is represented by concentrated solar power (CSP) technology, whose wide deployment is still hindered by its high investment costs. In CSP linear collector plants, a key component with high technological content may be identified in receiver tubes, that are traversed by heat transfer fluid and located on focal line on which solar radiation is concentrated by mirrors. The proposed work aims at developing spectrally selective coatings for receiver tubes able to overcome state‐of‐the‐art technological limitation in terms of both vacuum encapsulation and maximum operative temperature, currently limited at 550°C for molten salts CSP plants. To this aim, a multilayer structure was designed and developed for coating a receiver tube to be employed in open‐air environment at temperature of 600°C. The multilayer coating is based on tungsten chromium titanium infrared reflector and includes a solar absorber layer developed with two alternative methods of reactive sputtering and thermal oxidation respectively, finally covered by antireflective and barrier bi‐layer of aluminum oxide and silica. Thermal stability was demonstrated of the new developed coatings, since only small variations were measured of the optical parameters after more than 2000 h of aging in open air conditions at temperature of 600°C (on average less than 5%), with final measured solar absorptance αs of 73% and 87% and thermal emissivity εth at 600°C of 18% and 27% for aged multilayer structures including the absorber layer obtained through thermal oxidation and sputtering process, respectively. These results pave the way for further improvement in terms of both optical performance and operative temperature increase, allowing to enhance efficiency and lower costs, thus contributing to ease to deployment of CSP technology.
- Open Access
Materials Based on Amorphous Al2O3 and Composite W-Al2O3 for Solar Coatings Deposited by High-Rate Sputter Processes
In parabolic trough technology, the development of thermally and structurally stable solar coatings plays a key role in determining the efficiency, durability, and economic feasibility of tube receivers. A cermet-based solar coating is typically constituted by a thin film stratification, where a multilayer graded cermet is placed between an infrared metallic reflector and an antireflection filter. This work reports the realization of materials based on Al2O3 and W characterized by high structural and chemical stability in vacuum at high temperature, obtained through the optimization of high-deposition-rate processes. Al2O3 material, employed as the antireflection layer, was deposited through a reactive magnetron sputtering process at a high deposition rate. Cermet materials based on W-Al2O3 were deposited and employed as absorber layers by implementing reactive magnetron co-sputtering processes. An investigation into the stability of the realized samples was carried out by means of several material characterization methods before and after the annealing process in vacuum (1 × 10−3 Pa) at high temperature (620 °C). The structural properties of the samples were evaluated using Raman spectroscopy and XRD measurements, revealing a negligible presence of oxides that can compromise the structural stability. Spectrophotometric analysis showed little variations between the deposited and annealed samples, clearly indicating the high structural stability.
Open AccessMaterials Based on Amorphous Al2O3 and Composite W-Al2O3 for Solar Coatings Deposited by High-Rate Sputter Processes
In parabolic trough technology, the development of thermally and structurally stable solar coatings plays a key role in determining the efficiency, durability, and economic feasibility of tube receivers. A cermet-based solar coating is typically constituted by a thin film stratification, where a multilayer graded cermet is placed between an infrared metallic reflector and an antireflection filter. This work reports the realization of materials based on Al2O3 and W characterized by high structural and chemical stability in vacuum at high temperature, obtained through the optimization of high-deposition-rate processes. Al2O3 material, employed as the antireflection layer, was deposited through a reactive magnetron sputtering process at a high deposition rate. Cermet materials based on W-Al2O3 were deposited and employed as absorber layers by implementing reactive magnetron co-sputtering processes. An investigation into the stability of the realized samples was carried out by means of several material characterization methods before and after the annealing process in vacuum (1 × 10−3 Pa) at high temperature (620 °C). The structural properties of the samples were evaluated using Raman spectroscopy and XRD measurements, revealing a negligible presence of oxides that can compromise the structural stability. Spectrophotometric analysis showed little variations between the deposited and annealed samples, clearly indicating the high structural stability.
- 1 January 2022
- Published by AIP Publishing
- Vol. 2445, 020002
Spectrally selective solar coating based on W-AlN cermet fabricated by reactive sputtering processes at high deposition rate
- 1 January 2022
- Published by AIP Publishing
- Vol. 2445, 020002
Spectrally selective solar coating based on W-AlN cermet fabricated by reactive sputtering processes at high deposition rate
- Open Access
Solar Coatings Based on Ag Infrared Reflector with High Stability at Medium and High Temperature
The manufacturing of thermally stable solar coatings with high photo-thermal performance represents a key factor for the further deployment of the CSP technology. Since 2005, ENEA has been developing solar coatings suitable for medium and high temperature applications based on the technology of double nitride cermet, by employing silver and tungsten as infrared reflectors, respectively. Thanks to the high infrared reflectance of silver, the corresponding coatings have better optical performance than those with tungsten; however, the high diffusivity of silver compromises its use at high temperature. In order to improve the structural and chemical stability at medium and high temperature of coatings based on silver, this infrared reflector was placed between compact and uniform layers of metal and cermet manufactured by using high-energy and fast deposition processes. In particular, an Unbalanced Magnetron cathode was adopted to promote an ion-assisted deposition process that improved uniformity and compactness of the metal and cermet films. The new coating shows no photo-thermal parameters degradation after 25 years of service at the operating temperature of 400 °C, while its photo-thermal conversion efficiency decreases by only 1.5% after 25 years of service at an operating temperature of 514 °C.
Open AccessSolar Coatings Based on Ag Infrared Reflector with High Stability at Medium and High Temperature
The manufacturing of thermally stable solar coatings with high photo-thermal performance represents a key factor for the further deployment of the CSP technology. Since 2005, ENEA has been developing solar coatings suitable for medium and high temperature applications based on the technology of double nitride cermet, by employing silver and tungsten as infrared reflectors, respectively. Thanks to the high infrared reflectance of silver, the corresponding coatings have better optical performance than those with tungsten; however, the high diffusivity of silver compromises its use at high temperature. In order to improve the structural and chemical stability at medium and high temperature of coatings based on silver, this infrared reflector was placed between compact and uniform layers of metal and cermet manufactured by using high-energy and fast deposition processes. In particular, an Unbalanced Magnetron cathode was adopted to promote an ion-assisted deposition process that improved uniformity and compactness of the metal and cermet films. The new coating shows no photo-thermal parameters degradation after 25 years of service at the operating temperature of 400 °C, while its photo-thermal conversion efficiency decreases by only 1.5% after 25 years of service at an operating temperature of 514 °C.
- 21 July 2017
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry C
- Vol. 121 (30) , 16617-16628
Confinement of Semiconductor ZnO Nanoparticles in Block Copolymer Nanostructure
- 21 July 2017
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry C
- Vol. 121 (30) , 16617-16628
Confinement of Semiconductor ZnO Nanoparticles in Block Copolymer Nanostructure
- Open Access
- 1 January 2017
- Published by Elsevier in Materials Today: Proceedings
- Vol. 4 (4) , 5053-5059
Analysis of HMDS self-assembled monolayer Effect on Trap Density in PC70BM n-type Thin Film Transistors through Admittance Studies
- 1 January 2017
- Published by Elsevier in Materials Today: Proceedings
- Vol. 4 (4) , 5053-5059
Open AccessAnalysis of HMDS self-assembled monolayer Effect on Trap Density in PC70BM n-type Thin Film Transistors through Admittance Studies
- Open Access
- 1 January 2016
- Published by Elsevier in Materials Today: Proceedings
- Vol. 3 (3) , 720-726
PC70BM n-type Thin Film Transistors: Influence of HMDS Deposition Temperature on the Devices Properties
- 1 January 2016
- Published by Elsevier in Materials Today: Proceedings
- Vol. 3 (3) , 720-726
Open AccessPC70BM n-type Thin Film Transistors: Influence of HMDS Deposition Temperature on the Devices Properties