Ali Soleimanbeigi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Ali Soleimanbeigi has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Tuncer B. Edil
University of Wisconsin-Madison
9 shared publications - William J. Likos
Univ. of Wisconsin-Madison
6 shared publications - Jie Yin
Jiangsu Univ
5 shared publications - Craig H. Benson
Univ. of Wisconsin-Madison
2 shared publications Benjamin J. Warren
1 shared publication- Hua Yu
The University of Texas at Tyler, Tyler, USA
1 shared publication
Latest Publications
- 1 February 2018
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 144 (2)
Creep Response of Compacted Waste Foundry Sands for Use as Roadway Embankment Fill
Compressibility of five different samples of waste foundry sand (WFS) was evaluated through one-dimensional and triaxial compression tests to assess permanent strains under vertical and deviator stresses present in typical highway embankments. Results show that WFS containing a blend of sand and bentonite had higher compressibility than compacted natural sand. Compressibility of WFS is dependent on stress magnitude, time, and bentonite content. All samples of WFS exhibited one-dimensional secondary compression and deviatoric creep response similar to that of compacted natural soils. Compressibility and potential for creep rupture systematically increased with increasing bentonite content. For samples with relatively high bentonite content (12.8%), the maximum deviator stress to prevent creep rupture was reduced to 65% of the material’s compressive strength. One-dimensional compressibility parameters for compacted WFS were characterized as functions of bentonite content. Models were developed to estimate secondary compression ratio, deviatoric creep strain rates, and time to creep rupture for WFS at different stress levels and bentonite contents.
- 1 February 2018
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 144 (2)
Creep Response of Compacted Waste Foundry Sands for Use as Roadway Embankment Fill
Compressibility of five different samples of waste foundry sand (WFS) was evaluated through one-dimensional and triaxial compression tests to assess permanent strains under vertical and deviator stresses present in typical highway embankments. Results show that WFS containing a blend of sand and bentonite had higher compressibility than compacted natural sand. Compressibility of WFS is dependent on stress magnitude, time, and bentonite content. All samples of WFS exhibited one-dimensional secondary compression and deviatoric creep response similar to that of compacted natural soils. Compressibility and potential for creep rupture systematically increased with increasing bentonite content. For samples with relatively high bentonite content (12.8%), the maximum deviator stress to prevent creep rupture was reduced to 65% of the material’s compressive strength. One-dimensional compressibility parameters for compacted WFS were characterized as functions of bentonite content. Models were developed to estimate secondary compression ratio, deviatoric creep strain rates, and time to creep rupture for WFS at different stress levels and bentonite contents.
- 1 October 2017
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 29 (10)
Effects of Curing Time and Fly Ash Content on Properties of Stabilized Dredged Material
Properties of raw dredged material (RDM) stabilized with self-cementing Class C fly ash (FA) were evaluated for beneficial use in geotechnical construction applications. Emphasis was placed on evaluating effects of curing time and fly ash content on index and engineering properties relevant to pavement construction. RDM samples were blended with 10, 20, and 30% FA and cured for 2 h, 7 days, and 28 days. Fly ash stabilization reduced plasticity and improved the engineering properties of the stabilized dredged material (SDM). Increasing FA content increased maximum dry unit weight and reduced optimum water content for compaction. Unconfined compressive strength ( ) increased with FA content and curing time. The effect of curing time on was more significant at higher FA content. Freeze-thaw cycles only reduced the strength of SDM specimens by 5% on average, indicating that SDM was durable to freeze-thaw. Analytical relationships were developed to predict Atterberg limits and of SDM at different fly ash contents and curing times. The California bearing ratio (CBR) for the SDM ranged from 10 to 20, which is comparable to compacted silty sand or sand and rates as fair to good for pavement subgrade. The resilient modulus ( ) increased significantly with FA content and varied between 35 and 83 MPa, which is comparable to gravel or crushed stone and rates as good to excellent for subgrade. Results indicate that low-strength dredged materials stabilized with Class C fly ash are viable for beneficial use as pavement subgrade material.- 1 October 2017
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 29 (10)
Effects of Curing Time and Fly Ash Content on Properties of Stabilized Dredged Material
Properties of raw dredged material (RDM) stabilized with self-cementing Class C fly ash (FA) were evaluated for beneficial use in geotechnical construction applications. Emphasis was placed on evaluating effects of curing time and fly ash content on index and engineering properties relevant to pavement construction. RDM samples were blended with 10, 20, and 30% FA and cured for 2 h, 7 days, and 28 days. Fly ash stabilization reduced plasticity and improved the engineering properties of the stabilized dredged material (SDM). Increasing FA content increased maximum dry unit weight and reduced optimum water content for compaction. Unconfined compressive strength ( ) increased with FA content and curing time. The effect of curing time on was more significant at higher FA content. Freeze-thaw cycles only reduced the strength of SDM specimens by 5% on average, indicating that SDM was durable to freeze-thaw. Analytical relationships were developed to predict Atterberg limits and of SDM at different fly ash contents and curing times. The California bearing ratio (CBR) for the SDM ranged from 10 to 20, which is comparable to compacted silty sand or sand and rates as fair to good for pavement subgrade. The resilient modulus ( ) increased significantly with FA content and varied between 35 and 83 MPa, which is comparable to gravel or crushed stone and rates as good to excellent for subgrade. Results indicate that low-strength dredged materials stabilized with Class C fly ash are viable for beneficial use as pavement subgrade material.- 1 April 2017
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 143 (4)
Effects of Temperature on Creep Behavior of Compacted Recycled Asphalt Pavement
Recycled asphalt pavement (RAP) can be beneficially used as alternative construction material in geotechnical applications, but characterizing its creep response is important to account for potential viscous effects attributable to the material’s asphalt content. Effects of elevated temperature (35 and 50°C) on creep behavior of compacted RAP specimens were investigated through temperature-controlled triaxial compression tests at sustained deviator stresses. RAP compacted at room temperature (22°C) and subjected to deviator stress at elevated temperature showed creep strain and strain rate that systematically increased with increasing temperature. Time to creep rupture decreased with increasing temperature. Compaction at elevated temperature resulted in denser specimens and reduced creep strain and strain rate. Temperature effects were incorporated into a creep model that may be used to estimate strain rate of RAP at elevated temperatures. Construction of structural fills containing RAP is recomme...
- 1 April 2017
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 143 (4)
Effects of Temperature on Creep Behavior of Compacted Recycled Asphalt Pavement
Recycled asphalt pavement (RAP) can be beneficially used as alternative construction material in geotechnical applications, but characterizing its creep response is important to account for potential viscous effects attributable to the material’s asphalt content. Effects of elevated temperature (35 and 50°C) on creep behavior of compacted RAP specimens were investigated through temperature-controlled triaxial compression tests at sustained deviator stresses. RAP compacted at room temperature (22°C) and subjected to deviator stress at elevated temperature showed creep strain and strain rate that systematically increased with increasing temperature. Time to creep rupture decreased with increasing temperature. Compaction at elevated temperature resulted in denser specimens and reduced creep strain and strain rate. Temperature effects were incorporated into a creep model that may be used to estimate strain rate of RAP at elevated temperatures. Construction of structural fills containing RAP is recomme...
- 8 August 2016
- Published by American Society of Civil Engineers (ASCE)
- p. 42-51
Geotechnical Properties of Aged Municipal Solid Waste Incineration Fly Ash
Beneficial use of municipal solid waste incineration (MSWI) fly ash in road construction depends on the geotechnical properties required for performance. Geotechnical properties of aged MSWI fly ash samples were investigated through a series of laboratory tests. Physical properties of the aged MSWI ash closely resemble those of silty sand, with particle sizes ranging from 0.002 mm to 15 mm, specific gravity of 2.68-2.74 and maximum dry unit weight of 10.0-10.5 kN/m3. Hydraulic conductivity ranges from 10-4 cm/s to 10-6cm/s, which is similar to fine sands, silts and silty clays, and can be rated as “poor” drainage capacity. California bearing ratio (CBR) tests demonstrate that the CBR of aged ash samples is around 10 or higher, which can be rated as “fair-good” for fill and subgrade/subbase. Unconfined compressive strength is around 300 kN/m2 and reduces by less than 2% after 10 freeze-thaw cycles, indicating that the aged MSWI fly ash is durable with respect to freeze-thaw. Based on the tested geotechnical properties, the aged MSWI fly ash is recommended as an alternative lightweight material for fill and subgrade/subbase.
- 8 August 2016
- Published by American Society of Civil Engineers (ASCE)
- p. 42-51
Geotechnical Properties of Aged Municipal Solid Waste Incineration Fly Ash
Beneficial use of municipal solid waste incineration (MSWI) fly ash in road construction depends on the geotechnical properties required for performance. Geotechnical properties of aged MSWI fly ash samples were investigated through a series of laboratory tests. Physical properties of the aged MSWI ash closely resemble those of silty sand, with particle sizes ranging from 0.002 mm to 15 mm, specific gravity of 2.68-2.74 and maximum dry unit weight of 10.0-10.5 kN/m3. Hydraulic conductivity ranges from 10-4 cm/s to 10-6cm/s, which is similar to fine sands, silts and silty clays, and can be rated as “poor” drainage capacity. California bearing ratio (CBR) tests demonstrate that the CBR of aged ash samples is around 10 or higher, which can be rated as “fair-good” for fill and subgrade/subbase. Unconfined compressive strength is around 300 kN/m2 and reduces by less than 2% after 10 freeze-thaw cycles, indicating that the aged MSWI fly ash is durable with respect to freeze-thaw. Based on the tested geotechnical properties, the aged MSWI fly ash is recommended as an alternative lightweight material for fill and subgrade/subbase.
- 8 August 2016
- Published by American Society of Civil Engineers (ASCE)
- p. 400-410
Leaching Characteristics of Recycled Asphalt Shingles Mixed with Industrial Byproducts as Structural Fills
Leaching characteristics of recycled asphalt shingles (RAS) mixed with self-cementing fly ash (FA) for use as structural fill materials were investigated. Long-term column leaching tests were conducted on the compacted RAS-FA mixture containing 10% and 20% self-cementing FA. Results showed that peak concentrations for all investigated elements occurred in the first 5 pore volumes of flow (PVFs). Only arsenic (As) and selenium (Se) exceed the maximum contamination levels (MCLs) of U.S. EPA drinking water standard. The peak concentrations of As and Se from RAS-FA (80-20) were 10.2 and 18.8 times higher than the corresponding MCLs (AsMCL = 10 ppb and SeMCL = 50 ppb), while lower leached As and Se concentrations from the RAS-FA (90-10) were observed (7.1 and 1.8 times higher than the MCL values). WiscLEACH model was used to predict the environmental impact of RAS-FA mixtures as structural fills and calculate the reduction factors (RF) at a point of compliance (POC) 30 m away from the centerline of the roadway. The calculated RFs of As and Se were 14 and 18, respectively, and only concentration of Se leached from RAS-FA (80-20) were predicted higher than MCL at the POC. Based on mechanical and environmental evaluations, RAS-FA (90%-10%) is recommended for highway applications.
- 8 August 2016
- Published by American Society of Civil Engineers (ASCE)
- p. 400-410
Leaching Characteristics of Recycled Asphalt Shingles Mixed with Industrial Byproducts as Structural Fills
Leaching characteristics of recycled asphalt shingles (RAS) mixed with self-cementing fly ash (FA) for use as structural fill materials were investigated. Long-term column leaching tests were conducted on the compacted RAS-FA mixture containing 10% and 20% self-cementing FA. Results showed that peak concentrations for all investigated elements occurred in the first 5 pore volumes of flow (PVFs). Only arsenic (As) and selenium (Se) exceed the maximum contamination levels (MCLs) of U.S. EPA drinking water standard. The peak concentrations of As and Se from RAS-FA (80-20) were 10.2 and 18.8 times higher than the corresponding MCLs (AsMCL = 10 ppb and SeMCL = 50 ppb), while lower leached As and Se concentrations from the RAS-FA (90-10) were observed (7.1 and 1.8 times higher than the MCL values). WiscLEACH model was used to predict the environmental impact of RAS-FA mixtures as structural fills and calculate the reduction factors (RF) at a point of compliance (POC) 30 m away from the centerline of the roadway. The calculated RFs of As and Se were 14 and 18, respectively, and only concentration of Se leached from RAS-FA (80-20) were predicted higher than MCL at the POC. Based on mechanical and environmental evaluations, RAS-FA (90%-10%) is recommended for highway applications.
- 8 February 2016
- Published by American Society of Civil Engineers (ASCE)
Creep Behavior of Recycled Asphalt Pavement Compacted at Elevated Temperatures
Recycled asphalt pavement (RAP) can be beneficially reused as fill material in highway embankments or backfill behind retaining structures. In this study, deviator creep response of RAP compacted at different temperatures was investigated through a series of triaxial compression tests conducted at sustained deviatoric stresses. Test results showed that the compacted RAP represent classic creep response similar to soils. Creep rupture was observed at deviator stresses higher than 70% of the compressive strength. Compaction and compression at elevated temperatures increased the shear strength and reduced the creep strain of the RAP specimens. To minimize creep strain and potential for creep rupture, construction of structural fills containing RAP is recommended during warm months of the year.
- 8 February 2016
- Published by American Society of Civil Engineers (ASCE)
Creep Behavior of Recycled Asphalt Pavement Compacted at Elevated Temperatures
Recycled asphalt pavement (RAP) can be beneficially reused as fill material in highway embankments or backfill behind retaining structures. In this study, deviator creep response of RAP compacted at different temperatures was investigated through a series of triaxial compression tests conducted at sustained deviatoric stresses. Test results showed that the compacted RAP represent classic creep response similar to soils. Creep rupture was observed at deviator stresses higher than 70% of the compressive strength. Compaction and compression at elevated temperatures increased the shear strength and reduced the creep strain of the RAP specimens. To minimize creep strain and potential for creep rupture, construction of structural fills containing RAP is recommended during warm months of the year.
- 8 February 2016
- Published by American Society of Civil Engineers (ASCE)
- p. 1392-1403
Compression Behavior of Foundry Sands
Beneficial use and recycling of industrial byproducts promotes sustainability in roadway construction. An estimated 15 million tons of waste sands are produced from foundry operations (e.g., casting) in the US annually, out of which less than 28% is recycled and the remainder is landfilled. High-volume structural fill applications such as highway embankments can possibly use the majority of the foundry sands. One of the primary impediments to beneficial reuse of foundry sand in large volumes, however, is uncertainty with respect to its material and engineering properties, including compressibility and volume change. Foundry sand with bentonite binder may exhibit excessive permanent deformations under long-term loading. Compressibility of foundry sands from five different sources in Wisconsin were evaluated in a systematic suite of one-dimensional (1D) and three-dimensional (3D) compression tests. Compacted foundry sands are more compressible than compacted natural sands. Compressibility of foundry sand increases with bentonite fraction and the rate of secondary compression ratio increases with time. Compressibility parameters for foundry were quantified based on bentonite content. Recommended parameters can be used in numerical analyses to estimate creep deformations of embankments constructed with foundry sands at different stress levels, bentonite content, and time since construction.
- 8 February 2016
- Published by American Society of Civil Engineers (ASCE)
- p. 1392-1403
Compression Behavior of Foundry Sands
Beneficial use and recycling of industrial byproducts promotes sustainability in roadway construction. An estimated 15 million tons of waste sands are produced from foundry operations (e.g., casting) in the US annually, out of which less than 28% is recycled and the remainder is landfilled. High-volume structural fill applications such as highway embankments can possibly use the majority of the foundry sands. One of the primary impediments to beneficial reuse of foundry sand in large volumes, however, is uncertainty with respect to its material and engineering properties, including compressibility and volume change. Foundry sand with bentonite binder may exhibit excessive permanent deformations under long-term loading. Compressibility of foundry sands from five different sources in Wisconsin were evaluated in a systematic suite of one-dimensional (1D) and three-dimensional (3D) compression tests. Compacted foundry sands are more compressible than compacted natural sands. Compressibility of foundry sand increases with bentonite fraction and the rate of secondary compression ratio increases with time. Compressibility parameters for foundry were quantified based on bentonite content. Recommended parameters can be used in numerical analyses to estimate creep deformations of embankments constructed with foundry sands at different stress levels, bentonite content, and time since construction.
- 26 May 2015
- Published by Taylor & Francis in Road Materials and Pavement Design
- Vol. 16 (4) , 836-853
Climatic effect on resilient modulus of recycled unbound aggregates
The effect of temperature on plastic strain and resilient modulus (MR) of different sources of recycled asphalt pavement (RAP) and recycled concrete aggregate (RCA) was evaluated from the results of laboratory temperature-controlled MR tests, with a conventional Class 5 aggregate serving as the control. Freeze–thaw tests were also conducted on samples of RAP and RCA. Five years (spring–summer–fall–winter) of field falling weight deflectometer (FWD) tests were conducted on three pavement sections with RAP, RCA, and Class 5 as the unbound base course. Laboratory test results showed that temperature rise increased plastic strain and reduced MR of RAP under cyclic loads but had a negligible effect on plastic strain and MR of RCA. Freeze–thaw cycles steadily reduced the MR of RAP; however, long-term freeze–thaw cycles increased the MR of RCA. Thermal preloading reduced the plastic strain and increased the MR of the compacted RAP. Construction of a pavement system made with RAP is thus recommended during warm seasons to induce thermal preloading. The elastic modulus back-calculated from the FWD tests did not show a consistent trend with respect to temperature change. No significant change on elastic modulus of RAP, RCA, and Class 5 aggregates due to freeze–thaw cycles was observed over five years.
- 26 May 2015
- Published by Taylor & Francis in Road Materials and Pavement Design
- Vol. 16 (4) , 836-853
Climatic effect on resilient modulus of recycled unbound aggregates
The effect of temperature on plastic strain and resilient modulus (MR) of different sources of recycled asphalt pavement (RAP) and recycled concrete aggregate (RCA) was evaluated from the results of laboratory temperature-controlled MR tests, with a conventional Class 5 aggregate serving as the control. Freeze–thaw tests were also conducted on samples of RAP and RCA. Five years (spring–summer–fall–winter) of field falling weight deflectometer (FWD) tests were conducted on three pavement sections with RAP, RCA, and Class 5 as the unbound base course. Laboratory test results showed that temperature rise increased plastic strain and reduced MR of RAP under cyclic loads but had a negligible effect on plastic strain and MR of RCA. Freeze–thaw cycles steadily reduced the MR of RAP; however, long-term freeze–thaw cycles increased the MR of RCA. Thermal preloading reduced the plastic strain and increased the MR of the compacted RAP. Construction of a pavement system made with RAP is thus recommended during warm seasons to induce thermal preloading. The elastic modulus back-calculated from the FWD tests did not show a consistent trend with respect to temperature change. No significant change on elastic modulus of RAP, RCA, and Class 5 aggregates due to freeze–thaw cycles was observed over five years.
- 24 February 2014
- Published by American Society of Civil Engineers (ASCE)
- p. 3645-3657
Engineering Properties of Recycled Materials for Use as Embankment Fill
Use of recycled materials promotes sustainability in geotechnical construction. Compaction characteristics, hydraulic conductivity, shear strength, and compressibility of bottom ash (BA), foundry slag (FS), recycled asphalt pavement (RAP), and recycled asphalt shingles (RAS) that are produced in large quantities were characterized. Results showed that BA, FS, and RAS have lower maximum dry unit weight than compacted sand and the dry unit weights are not sensitive to compaction moisture content. Shear strength of the tested recycled materials are adequate to provide stability for typical highway embankments. The measured hydraulic conductivities provide sufficient drainage capacity for embankment fills. Results of one-dimensional compression tests showed that BA and FS have comparable compressibility to that of compacted sand up to vertical effective stress (σ'v) of 200 kPa after which BA and FS exhibited higher compressibility than sand due to crushing of individual particles. Compressibility of RAS is significantly higher than that of sand, which makes the material unsuitable as embankment fill. RAP consistently has higher compressibility than sand; however, settlement of typical highway embankments constructed with RAP is still below the typical allowable limit. BA, FS, and RAP have appropriate engineering properties for use as structural fill in typical highway embankments. RAS should be mixed with at least 50% of granular additive to reduce compressibility to an acceptable limit. Construction of embankments with RAS mixture or RAP is recommended during warm seasons to induce thermal preloading and reduce compressibility.
- 24 February 2014
- Published by American Society of Civil Engineers (ASCE)
- p. 3645-3657
Engineering Properties of Recycled Materials for Use as Embankment Fill
Use of recycled materials promotes sustainability in geotechnical construction. Compaction characteristics, hydraulic conductivity, shear strength, and compressibility of bottom ash (BA), foundry slag (FS), recycled asphalt pavement (RAP), and recycled asphalt shingles (RAS) that are produced in large quantities were characterized. Results showed that BA, FS, and RAS have lower maximum dry unit weight than compacted sand and the dry unit weights are not sensitive to compaction moisture content. Shear strength of the tested recycled materials are adequate to provide stability for typical highway embankments. The measured hydraulic conductivities provide sufficient drainage capacity for embankment fills. Results of one-dimensional compression tests showed that BA and FS have comparable compressibility to that of compacted sand up to vertical effective stress (σ'v) of 200 kPa after which BA and FS exhibited higher compressibility than sand due to crushing of individual particles. Compressibility of RAS is significantly higher than that of sand, which makes the material unsuitable as embankment fill. RAP consistently has higher compressibility than sand; however, settlement of typical highway embankments constructed with RAP is still below the typical allowable limit. BA, FS, and RAP have appropriate engineering properties for use as structural fill in typical highway embankments. RAS should be mixed with at least 50% of granular additive to reduce compressibility to an acceptable limit. Construction of embankments with RAS mixture or RAP is recommended during warm seasons to induce thermal preloading and reduce compressibility.
- 25 February 2013
- Published by American Society of Civil Engineers (ASCE)
- p. 92-96
Evaluation of Shear Creep Response of Recycled Asphalt Shingle Mixtures
In this research, shear creep response of recycled asphalt shingles (RAS) stabilized with self-cementing fly ash (FA) and RAS mixed with bottom ash (BA) were investigated. Systematic constant stress consolidated-drained triaxial tests were conducted on compacted RAS:BA mixtures and fly ash stabilized RAS at different deviator stress levels, temperatures and confining pressures. Creep rupture was observed at deviator stress levels higher than 80% of the deviator stress at failure. Strain rate also increased as an exponential function of temperature. In designing side slopes of highway embankments containing RAS, the maximum deviator stress obtained from the triaxial compression test should be reduced by at least 20% to prevent the creep rupture. Construction of embankment fills containing RAS is recommended during warm seasons to minimize long term creep deformation of the embankment side slopes.
- 25 February 2013
- Published by American Society of Civil Engineers (ASCE)
- p. 92-96
Evaluation of Shear Creep Response of Recycled Asphalt Shingle Mixtures
In this research, shear creep response of recycled asphalt shingles (RAS) stabilized with self-cementing fly ash (FA) and RAS mixed with bottom ash (BA) were investigated. Systematic constant stress consolidated-drained triaxial tests were conducted on compacted RAS:BA mixtures and fly ash stabilized RAS at different deviator stress levels, temperatures and confining pressures. Creep rupture was observed at deviator stress levels higher than 80% of the deviator stress at failure. Strain rate also increased as an exponential function of temperature. In designing side slopes of highway embankments containing RAS, the maximum deviator stress obtained from the triaxial compression test should be reduced by at least 20% to prevent the creep rupture. Construction of embankment fills containing RAS is recommended during warm seasons to minimize long term creep deformation of the embankment side slopes.