Shuai Zheng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Shuai Zheng has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
- Yi Yang
School of Transportation Engineering, Dalian Jiaotong University, Dalian, China
3 shared publications - Annan Jiang
College of Transportation Engineering, Dalian Maritime University, Dalian, China
2 shared publications - Hangyu Zhang
School of Transportation Engineering, Dalian Jiaotong University, Dalian 116028, China
2 shared publications - Shiqun Li
College of Zhan Tianyou, Dalian Jiaotong University, Dalian 116028, China
2 shared publications - Sihui Dong
School of Transportation Engineering, Dalian Jiaotong University, Dalian 116028, China
2 shared publications Wenrui Bian
Zhan Tianyou College, Dalian Jiaotong University, Dalian, China
2 shared publications
Latest Publications
- 27 August 2026
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
Large Deformation Control and Structural Optimization of Tunnels in Shallow Fractured and Expansive Formations Based on Discrete Element Simulation
Tunnel construction in shallow-buried fractured and swelling schistose rock formations is highly prone to large structural deformation issues. Taking the context of a tunnel located on the Xi’an–Ankang high-speed railway as background, thorough investigations were conducted into the arch crown subsidence, horizontal convergence, initial support cracking, and spalling, as well as ground deformation. Subsequently, an optimization of the original support scheme was carried out using the Universal Distinct Element Code (UDEC) software. The results revealed that large deformation is more likely to occur at the top and foot of the arch in the shallow-buried fractured and swelling schistose rock, characterized by phenomena such as cracking and spalling of sprayed concrete, longitudinal cracks in the arch crown, bending of steel arches, and substantial convergence and deformation of the arch crown. Through comparative analysis using UDEC modeling it was determined that among all the optimized schemes the most effective measure for controlling large deformation in shallow-buried fractured schistose rock is the addition of lock foot anchor rods, which resulted in reductions of over 50% in arch crown subsidence and horizontal convergence compared with the original design, while the plastic zone range decreased by 80%.
- 27 August 2026
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
Large Deformation Control and Structural Optimization of Tunnels in Shallow Fractured and Expansive Formations Based on Discrete Element Simulation
Tunnel construction in shallow-buried fractured and swelling schistose rock formations is highly prone to large structural deformation issues. Taking the context of a tunnel located on the Xi’an–Ankang high-speed railway as background, thorough investigations were conducted into the arch crown subsidence, horizontal convergence, initial support cracking, and spalling, as well as ground deformation. Subsequently, an optimization of the original support scheme was carried out using the Universal Distinct Element Code (UDEC) software. The results revealed that large deformation is more likely to occur at the top and foot of the arch in the shallow-buried fractured and swelling schistose rock, characterized by phenomena such as cracking and spalling of sprayed concrete, longitudinal cracks in the arch crown, bending of steel arches, and substantial convergence and deformation of the arch crown. Through comparative analysis using UDEC modeling it was determined that among all the optimized schemes the most effective measure for controlling large deformation in shallow-buried fractured schistose rock is the addition of lock foot anchor rods, which resulted in reductions of over 50% in arch crown subsidence and horizontal convergence compared with the original design, while the plastic zone range decreased by 80%.
- Open Access
- 31 July 2026
- Published by Springer Nature in Scientific Reports
- Vol. 16 (1)
Adaptive shield TBM selection model integrating AHP with attention mechanism and its engineering application
- 31 July 2026
- Published by Springer Nature in Scientific Reports
- Vol. 16 (1)
Open AccessAdaptive shield TBM selection model integrating AHP with attention mechanism and its engineering application
- 9 April 2026
- Published by Springer Nature in International Journal of Geosynthetics and Ground Engineering
- Vol. 12 (2) , 21
Coupled Time-Varying Model of Tunnel Damage-Seepage in Complex Geology and Soil Response Behavior Analysis
- 9 April 2026
- Published by Springer Nature in International Journal of Geosynthetics and Ground Engineering
- Vol. 12 (2) , 21
Coupled Time-Varying Model of Tunnel Damage-Seepage in Complex Geology and Soil Response Behavior Analysis
- 6 October 2025
- Published by IOP Publishing in Engineering Research Express
- Vol. 7 (4) , 045102
Real-time prediction method of shield tunneling attitude under complex geological conditions
Accurate prediction of shield tunneling attitude is crucial for preventing engineering risks such as tunnel misalignment, structural collisions, and ground subsidence in underground construction projects. This study develops a real-time prediction method for shield tunneling parameters using the Qingdao Jiaozhou Bay Second Subsea Tunnel as a case study. We systematically compare three machine learning approaches (XGBoost, Transformer, and LSTM) enhanced with discrete wavelet transform (DWT) for noise reduction and Bayesian optimization (BOA) for hyperparameter tuning. Results show that BOA-XGBoost achieved the R2 is 0.98 with the Mean Absolute Percentage Error (MAPE) errors below 2% for all five output parameters (horizontal/vertical deviations at shield head/tail and roll angle). While BOA-XGBoost outperformed other models in accuracy, BOA-LSTM demonstrated superior computational efficiency—33.44% faster than XGBoost and 96.79% faster than Transformer. Under complex geological conditions, deep learning models (BOA-LSTM and BOA-Transformer) showed better adaptability than BOA-XGBoost, particularly in mixed soil-rock strata. This study provides practical guidance for selecting appropriate prediction models based on geological conditions and computational constraints in tunnel engineering projects.
- 6 October 2025
- Published by IOP Publishing in Engineering Research Express
- Vol. 7 (4) , 045102
Real-time prediction method of shield tunneling attitude under complex geological conditions
Accurate prediction of shield tunneling attitude is crucial for preventing engineering risks such as tunnel misalignment, structural collisions, and ground subsidence in underground construction projects. This study develops a real-time prediction method for shield tunneling parameters using the Qingdao Jiaozhou Bay Second Subsea Tunnel as a case study. We systematically compare three machine learning approaches (XGBoost, Transformer, and LSTM) enhanced with discrete wavelet transform (DWT) for noise reduction and Bayesian optimization (BOA) for hyperparameter tuning. Results show that BOA-XGBoost achieved the R2 is 0.98 with the Mean Absolute Percentage Error (MAPE) errors below 2% for all five output parameters (horizontal/vertical deviations at shield head/tail and roll angle). While BOA-XGBoost outperformed other models in accuracy, BOA-LSTM demonstrated superior computational efficiency—33.44% faster than XGBoost and 96.79% faster than Transformer. Under complex geological conditions, deep learning models (BOA-LSTM and BOA-Transformer) showed better adaptability than BOA-XGBoost, particularly in mixed soil-rock strata. This study provides practical guidance for selecting appropriate prediction models based on geological conditions and computational constraints in tunnel engineering projects.
- 16 September 2025
- Published by IOP Publishing in Engineering Research Express
- Vol. 7 (3) , 035145
A new DEM calibration method for the adhesion and shear behavior of clay materials based on response surface methodology
The Discrete Element Method (DEM) is a commonly used numerical analysis tool for simulating the mechanical behavior of clay materials. DEM models require the specification of microscopic virtual parameters that are not measurable and are not directly related to the macroscopic characteristics of the material. Therefore, calibration of these microscopic virtual parameters is necessary to simulate the mechanical behavior of clay. Calibration typically uses an iterative trial-and-error method, which involves running multiple DEM simulations, making the calibration process computationally expensive. In this work, we propose a calibration method based on Response Surface Methodology for designing virtual direct shear and adhesion shear experiments. This method significantly reduces the number of DEM simulations required during the calibration process, thus lowering the associated computational cost. Using this approach, the shear stress–strain curve for clay materials was obtained, and a comparison with experimental data shows that the response surface model generated by this method demonstrates high accuracy and reliability. The application of this method to simulate the shear and adhesion behavior of clay represents a novel approach. Validation was performed through a case study of a tunnel boring machine operating in clay, and the predicted results aligned well with the measured data, confirming the applicability of the method. This approach provides effective theoretical support for studying the interaction between clay and machinery.
- 16 September 2025
- Published by IOP Publishing in Engineering Research Express
- Vol. 7 (3) , 035145
A new DEM calibration method for the adhesion and shear behavior of clay materials based on response surface methodology
The Discrete Element Method (DEM) is a commonly used numerical analysis tool for simulating the mechanical behavior of clay materials. DEM models require the specification of microscopic virtual parameters that are not measurable and are not directly related to the macroscopic characteristics of the material. Therefore, calibration of these microscopic virtual parameters is necessary to simulate the mechanical behavior of clay. Calibration typically uses an iterative trial-and-error method, which involves running multiple DEM simulations, making the calibration process computationally expensive. In this work, we propose a calibration method based on Response Surface Methodology for designing virtual direct shear and adhesion shear experiments. This method significantly reduces the number of DEM simulations required during the calibration process, thus lowering the associated computational cost. Using this approach, the shear stress–strain curve for clay materials was obtained, and a comparison with experimental data shows that the response surface model generated by this method demonstrates high accuracy and reliability. The application of this method to simulate the shear and adhesion behavior of clay represents a novel approach. Validation was performed through a case study of a tunnel boring machine operating in clay, and the predicted results aligned well with the measured data, confirming the applicability of the method. This approach provides effective theoretical support for studying the interaction between clay and machinery.
- 1 September 2025
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 43 (8) , 1-18
ZSI-R Method for Evaluating Foundation Pit Stability in Karst Regions
- 1 September 2025
- Published by Springer Nature in Geotechnical and Geological Engineering
- Vol. 43 (8) , 1-18
ZSI-R Method for Evaluating Foundation Pit Stability in Karst Regions
- Open Access
Sensitivity Analysis and Optimization of Urban Roundabout Road Design Parameters Based on CFD
With the rapid advancement of urbanization, urban transportation systems are facing increasingly severe congestion challenges, especially at traditional roundabouts. The rapid increase in vehicles has led to a sharp increase in pressure at roundabouts. In order to alleviate the traffic pressure in the roundabout, this paper changes the road design parameters of the roundabout, uses a CFD method combined with sensitivity analysis to study the influence of different inlet angles, lane numbers, and the outer radius on the pressure, and seeks the road design parameter scheme with the optimal mitigation effect. Firstly, the full factorial experimental design method is used to select the sample points in the design sample space, and the response values of each sample matrix are obtained by CFD. Secondly, the response surface model between the road design parameters of the roundabout and the pressure in the ring is constructed. The single-factor analysis method and the multi-factor analysis method are used to analyze the influence of the road parameters on the pressure of each feature point, and then the moment-independent sensitivity analysis method based on the response surface model is used to solve the sensitivity distribution characteristics of the road design parameters of the roundabout. Finally, the Kriging surrogate model is constructed, and the NSGA-II is used to solve the multi-objective optimization problem to obtain the optimal solution set of road parameters. The results show that there are significant differences in the mechanism of action of different road geometric parameters on the pressure of each feature point of the roundabout, and it shows obvious spatial heterogeneity of parameter sensitivity. The pressure changes in the two feature points at the entrance conflict area and the inner ring weaving area are significantly correlated with the lane number parameters. There is a strong coupling relationship between the pressure of the maximum pressure extreme point in the ring and the radius parameters of the outer ring. According to the optimal scheme of road parameters, that is, when the parameter set (inlet angle/°, number of lanes, outer radius/m) meets (35.4, 5, 65), the pressures of the feature points decrease by 34.1%, 38.3%, and 20.7%, respectively, which has a significant effect on alleviating the pressure in the intersection. This study optimizes the geometric parameters of roundabouts through multidisciplinary methods, provides a data-driven congestion reduction strategy for the urban sustainable development framework, and significantly improves road traffic efficiency, which is crucial for building an efficient traffic network and promoting urban sustainable development.
Open AccessSensitivity Analysis and Optimization of Urban Roundabout Road Design Parameters Based on CFD
With the rapid advancement of urbanization, urban transportation systems are facing increasingly severe congestion challenges, especially at traditional roundabouts. The rapid increase in vehicles has led to a sharp increase in pressure at roundabouts. In order to alleviate the traffic pressure in the roundabout, this paper changes the road design parameters of the roundabout, uses a CFD method combined with sensitivity analysis to study the influence of different inlet angles, lane numbers, and the outer radius on the pressure, and seeks the road design parameter scheme with the optimal mitigation effect. Firstly, the full factorial experimental design method is used to select the sample points in the design sample space, and the response values of each sample matrix are obtained by CFD. Secondly, the response surface model between the road design parameters of the roundabout and the pressure in the ring is constructed. The single-factor analysis method and the multi-factor analysis method are used to analyze the influence of the road parameters on the pressure of each feature point, and then the moment-independent sensitivity analysis method based on the response surface model is used to solve the sensitivity distribution characteristics of the road design parameters of the roundabout. Finally, the Kriging surrogate model is constructed, and the NSGA-II is used to solve the multi-objective optimization problem to obtain the optimal solution set of road parameters. The results show that there are significant differences in the mechanism of action of different road geometric parameters on the pressure of each feature point of the roundabout, and it shows obvious spatial heterogeneity of parameter sensitivity. The pressure changes in the two feature points at the entrance conflict area and the inner ring weaving area are significantly correlated with the lane number parameters. There is a strong coupling relationship between the pressure of the maximum pressure extreme point in the ring and the radius parameters of the outer ring. According to the optimal scheme of road parameters, that is, when the parameter set (inlet angle/°, number of lanes, outer radius/m) meets (35.4, 5, 65), the pressures of the feature points decrease by 34.1%, 38.3%, and 20.7%, respectively, which has a significant effect on alleviating the pressure in the intersection. This study optimizes the geometric parameters of roundabouts through multidisciplinary methods, provides a data-driven congestion reduction strategy for the urban sustainable development framework, and significantly improves road traffic efficiency, which is crucial for building an efficient traffic network and promoting urban sustainable development.
- Open Access
- 26 May 2025
- Published by MDPI AG in Preprints.org
Sensitivity Analysis and Optimization of Urban Roundabout Road Design Parameters Based on CFD
With the rapid advancement of urbanization, urban transportation systems are facing increasingly severe congestion challenges, especially at traditional roundabouts. The rapid increase in vehicles has led to a sharp increase in pressure at roundabouts. In order to alleviate the traffic pressure in the roundabout, this paper changes the road design parameters of the roundabout, uses CFD method combined with sensitivity analysis to study the influence of different inlet angles, lane numbers and outer radius on the pressure, and seeks the road design parameter scheme with the optimal mitigation effect. Firstly, the full factorial experimental design method is used to select the sample points in the design sample space, and the response values of each sample matrix are obtained by CFD. Secondly, the response surface model between the road design parameters of the roundabout and the pressure in the ring is constructed. The single factor analysis method and the multi-factor analysis method are used to analyze the influence of the road parameters on the pressure of each feature point, and then the moment independent sensitivity analysis method based on the response surface model is used to solve the sensitivity distribution characteristics of the road design parameters of the roundabout. Finally, the Kriging surrogate model is constructed, and the NSGA-II is used to solve the multi-objective optimization problem to obtain the optimal solution set of road parameters. The results show that there are significant differences in the mechanism of action of different road geometric parameters on the pressure of each feature point of the roundabout, and it shows obvious spatial heterogeneity of parameter sensitivity. The pressure changes of the two feature points at the entrance conflict area and the inner ring weaving area are significantly correlated with the lane number parameters. There is a strong coupling relationship between the pressure of the maximum pressure extreme point in the ring and the radius parameters of the outer ring. According to the optimal scheme of road parameters, that is, when the parameter set (inlet angle/°, number of lanes, outer radius/ m) meets (35.4, 5, 65), the pressure of feature points decreases by 34.1%, 38.3% and 20.7% respectively, which has a significant effect on alleviating the pressure in the intersection. This study optimizes the geometric parameters of roundabouts through multidisciplinary methods, provides a data-driven congestion reduction strategy for the urban sustainable development framework, and significantly improves road traffic efficiency, which is crucial for building an efficient traffic network and promoting urban sustainable development.
- 26 May 2025
- Published by MDPI AG in Preprints.org
Open AccessSensitivity Analysis and Optimization of Urban Roundabout Road Design Parameters Based on CFD
With the rapid advancement of urbanization, urban transportation systems are facing increasingly severe congestion challenges, especially at traditional roundabouts. The rapid increase in vehicles has led to a sharp increase in pressure at roundabouts. In order to alleviate the traffic pressure in the roundabout, this paper changes the road design parameters of the roundabout, uses CFD method combined with sensitivity analysis to study the influence of different inlet angles, lane numbers and outer radius on the pressure, and seeks the road design parameter scheme with the optimal mitigation effect. Firstly, the full factorial experimental design method is used to select the sample points in the design sample space, and the response values of each sample matrix are obtained by CFD. Secondly, the response surface model between the road design parameters of the roundabout and the pressure in the ring is constructed. The single factor analysis method and the multi-factor analysis method are used to analyze the influence of the road parameters on the pressure of each feature point, and then the moment independent sensitivity analysis method based on the response surface model is used to solve the sensitivity distribution characteristics of the road design parameters of the roundabout. Finally, the Kriging surrogate model is constructed, and the NSGA-II is used to solve the multi-objective optimization problem to obtain the optimal solution set of road parameters. The results show that there are significant differences in the mechanism of action of different road geometric parameters on the pressure of each feature point of the roundabout, and it shows obvious spatial heterogeneity of parameter sensitivity. The pressure changes of the two feature points at the entrance conflict area and the inner ring weaving area are significantly correlated with the lane number parameters. There is a strong coupling relationship between the pressure of the maximum pressure extreme point in the ring and the radius parameters of the outer ring. According to the optimal scheme of road parameters, that is, when the parameter set (inlet angle/°, number of lanes, outer radius/ m) meets (35.4, 5, 65), the pressure of feature points decreases by 34.1%, 38.3% and 20.7% respectively, which has a significant effect on alleviating the pressure in the intersection. This study optimizes the geometric parameters of roundabouts through multidisciplinary methods, provides a data-driven congestion reduction strategy for the urban sustainable development framework, and significantly improves road traffic efficiency, which is crucial for building an efficient traffic network and promoting urban sustainable development.
- 1 December 2024
- Published by IOP Publishing in Engineering Research Express
- Vol. 6 (4) , 045120
Study on the disturbance law of the new viaduct pile foundation construction to the subway in the adjacent operation
During the construction of elevated bridge pile foundations, the mechanical processes, including the extrusion and friction caused by the steel casing’s rotation into the soil and the soil pressure unloading due to soil extraction from pile holes, can significantly disturb existing structures. To address the engineering challenge posed by the planned elevated bridge on Yuanjiang Street Expressway in Shenyang, which is adjacent to the operational Metro Line 10 Dingxianghu Station, this study investigates the disturbance laws of the pile foundation construction on the mechanical behavior of the subway station. A three-dimensional finite element model of the target project was constructed, and numerical simulations were conducted, with a focus on the stress transfer phenomenon caused by friction between the casing and the soil during rotary excavation. The disturbance laws of pile foundation construction on the nearby operating metro structure and the surrounding soil under different excavation sequences were analyzed. The results indicate that the extent of soil settlement is inversely proportional to the distance from the pile foundation; the maximum compressive stress on the top of the station is 2.23 MPa, and the maximum tensile stress at the bottom is 1.31 MPa. The disturbances to the subway station caused by symmetrical drilling, row drilling, and skip pile drilling decrease in that order. The maximum lateral displacement of the subway station is reduced by 57.2% and 26.6% compared to the case without changing the excavation sequence. The study provides insights into the disturbance laws caused by the mechanical transmission path formed by soil friction during the rotary excavation of new elevated bridge pile foundations near operating subway station, offering theoretical reference for future similar engineering projects.
- 1 December 2024
- Published by IOP Publishing in Engineering Research Express
- Vol. 6 (4) , 045120
Study on the disturbance law of the new viaduct pile foundation construction to the subway in the adjacent operation
During the construction of elevated bridge pile foundations, the mechanical processes, including the extrusion and friction caused by the steel casing’s rotation into the soil and the soil pressure unloading due to soil extraction from pile holes, can significantly disturb existing structures. To address the engineering challenge posed by the planned elevated bridge on Yuanjiang Street Expressway in Shenyang, which is adjacent to the operational Metro Line 10 Dingxianghu Station, this study investigates the disturbance laws of the pile foundation construction on the mechanical behavior of the subway station. A three-dimensional finite element model of the target project was constructed, and numerical simulations were conducted, with a focus on the stress transfer phenomenon caused by friction between the casing and the soil during rotary excavation. The disturbance laws of pile foundation construction on the nearby operating metro structure and the surrounding soil under different excavation sequences were analyzed. The results indicate that the extent of soil settlement is inversely proportional to the distance from the pile foundation; the maximum compressive stress on the top of the station is 2.23 MPa, and the maximum tensile stress at the bottom is 1.31 MPa. The disturbances to the subway station caused by symmetrical drilling, row drilling, and skip pile drilling decrease in that order. The maximum lateral displacement of the subway station is reduced by 57.2% and 26.6% compared to the case without changing the excavation sequence. The study provides insights into the disturbance laws caused by the mechanical transmission path formed by soil friction during the rotary excavation of new elevated bridge pile foundations near operating subway station, offering theoretical reference for future similar engineering projects.