Oualid Chahaoui
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Oualid Chahaoui has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Salim Boulahrouz
Abbés Laghrour University, Algeria
3 shared publications - Abdenour Saoudi
Department of Mechanical Engineering, and Advanced Materials Laboratory (ISMA), Abbes Laghrour University, Khenchela 40000, Algeria
2 shared publications - Mohamed Lamine Fares
Badji-Mokhtar-Annaba University
2 shared publications - Mohammed Muzibur Rahman
Chemistry Department, Faculty of Science, King Abdulaziz University, Jeddah, Saudi Arabia
2 shared publications - Nedjoua Matougui
L3M Mining, Metallurgy and Materials Laboratory, Mining, Metallurgy and Materials Department, National Higher School of Technology and Engineering, Sidi Amar, 23000 Annaba, Algeria
2 shared publications - Abdelouahad Chala
University of Biskra
1 shared publication
Latest Publications
- Open Access
- 28 April 2026
- Published by IOP Publishing in Materials Research Express
- Vol. 13 (9) , 096501
Enhancing the deep drawing process by predicting damage initiation and progression using the anisotropic Lemaitre damage model
The originality of the approach proposed in this work lies in the integration of the effect of plastic anisotropy on the initiation and propagation of ductile damage via the modified Lemaitre damage model. The main objective is to improve the deep drawing of sheet metal during forming, particularly DC04 steel. The proposed model adopts a coupling between anisotropic plasticity, described by Hill’s plasticity criterion (1948), and a direction-dependent damage propagation law, identified experimentally. For this purpose, a comprehensive experimental campaign was conducted using monotonic and cyclic tensile tests (loading-unloading), at different orientations (0°, 45°, and 90°) relative to the rolling direction. Strain gradient measurements were obtained using digital image correlation, while damage propagation was quantified by the degradation of Young’s modulus. In addition, a model simulation based on ( FEM ) was validated by implementing these parameters, identified via Abaqus/Explicit using a VUMAT subroutine. Compared to classical isotropic damage models, the proposed new correlation methodology significantly improves the prediction of damage initiation, localization, and critical thresholds. The model accurately reproduces the greater sensitivity to damage observed at 45°, associated with lower Lankford coefficients and improved strain localization. The integration of anisotropy in plasticity and damage evolution enables more realistic simulations of deep drawing processes and provides a reliable tool for industrial forming applications.
- 28 April 2026
- Published by IOP Publishing in Materials Research Express
- Vol. 13 (9) , 096501
Open AccessEnhancing the deep drawing process by predicting damage initiation and progression using the anisotropic Lemaitre damage model
The originality of the approach proposed in this work lies in the integration of the effect of plastic anisotropy on the initiation and propagation of ductile damage via the modified Lemaitre damage model. The main objective is to improve the deep drawing of sheet metal during forming, particularly DC04 steel. The proposed model adopts a coupling between anisotropic plasticity, described by Hill’s plasticity criterion (1948), and a direction-dependent damage propagation law, identified experimentally. For this purpose, a comprehensive experimental campaign was conducted using monotonic and cyclic tensile tests (loading-unloading), at different orientations (0°, 45°, and 90°) relative to the rolling direction. Strain gradient measurements were obtained using digital image correlation, while damage propagation was quantified by the degradation of Young’s modulus. In addition, a model simulation based on ( FEM ) was validated by implementing these parameters, identified via Abaqus/Explicit using a VUMAT subroutine. Compared to classical isotropic damage models, the proposed new correlation methodology significantly improves the prediction of damage initiation, localization, and critical thresholds. The model accurately reproduces the greater sensitivity to damage observed at 45°, associated with lower Lankford coefficients and improved strain localization. The integration of anisotropy in plasticity and damage evolution enables more realistic simulations of deep drawing processes and provides a reliable tool for industrial forming applications.
- Open Access
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 29 (4) , e20240468
Characterization of fracture and impact behavior of plasma nitrided 42crmo4 steel: structural and mechanical properties
This study examines the impact of adding nitrogen (N+) to the surface of 42CrMo4 steel on its structural and mechanical properties. The specimens (T2, I2) were nitrided first at 580°C for 13 hours, and then at 560°C to remove oxides. Later, we compared them with the untreated specimens (T1, I1) to assess the impact of thermochemical treatment. The mechanical properties and fracture behaviors were examined and analyzed using Vickers microhardness, unidirectional tensile, and Charpy U tests. The nitrogen and carbon profiles in the nitrided layer were predicted by simulating the nitriding process. Findings show a progressive decrease in nitrogen content from 0.6 to 0 wt.%, unlike the carbon which increases to 0.4 wt.% after 414 μm. Besides, the microscopic observations show a dense white layer of nitrides (T2, I2), while the untreated specimens exhibit a ferrite and pearlite microstructure. The X-ray diffraction (XRD) analyses show the formation of iron and chromium nitrides (ε-Fe2-3N, γ-Fe4N, γ-(Fe, Cr) N4) in the surface layer, accompanied by a decrease in pure α-iron. The nitrided 42CrMo4 steel is characterized with an increase in the lattice parameter, followed by a reduction in the grain size. Moreover, the maximum hardness of approximately 603 HV in the nitrided layer decreased to around 215 HV at a depth of 414 μm. The uniaxial tensile test reveals ductile behavior at the core of the nitrided steel, unlike the surface, which is hard and fragile. Finally, the mechanical properties improve after plasma nitriding, increasing the elasticity modulus to E = 401700 MPa and the tensile strength to Rm = 1219.7 MPa.
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 29 (4) , e20240468
Open AccessCharacterization of fracture and impact behavior of plasma nitrided 42crmo4 steel: structural and mechanical properties
This study examines the impact of adding nitrogen (N+) to the surface of 42CrMo4 steel on its structural and mechanical properties. The specimens (T2, I2) were nitrided first at 580°C for 13 hours, and then at 560°C to remove oxides. Later, we compared them with the untreated specimens (T1, I1) to assess the impact of thermochemical treatment. The mechanical properties and fracture behaviors were examined and analyzed using Vickers microhardness, unidirectional tensile, and Charpy U tests. The nitrogen and carbon profiles in the nitrided layer were predicted by simulating the nitriding process. Findings show a progressive decrease in nitrogen content from 0.6 to 0 wt.%, unlike the carbon which increases to 0.4 wt.% after 414 μm. Besides, the microscopic observations show a dense white layer of nitrides (T2, I2), while the untreated specimens exhibit a ferrite and pearlite microstructure. The X-ray diffraction (XRD) analyses show the formation of iron and chromium nitrides (ε-Fe2-3N, γ-Fe4N, γ-(Fe, Cr) N4) in the surface layer, accompanied by a decrease in pure α-iron. The nitrided 42CrMo4 steel is characterized with an increase in the lattice parameter, followed by a reduction in the grain size. Moreover, the maximum hardness of approximately 603 HV in the nitrided layer decreased to around 215 HV at a depth of 414 μm. The uniaxial tensile test reveals ductile behavior at the core of the nitrided steel, unlike the surface, which is hard and fragile. Finally, the mechanical properties improve after plasma nitriding, increasing the elasticity modulus to E = 401700 MPa and the tensile strength to Rm = 1219.7 MPa.
- Open Access
- 3 August 2023
- Published by Elsevier in Alexandria Engineering Journal
- Vol. 78, 426-437
Three-dimensional transient CFD modeling of multiple finned aluminum foam heat sinks in a horizontal channel
- 3 August 2023
- Published by Elsevier in Alexandria Engineering Journal
- Vol. 78, 426-437
Open AccessThree-dimensional transient CFD modeling of multiple finned aluminum foam heat sinks in a horizontal channel
- Open Access
- 1 January 2021
- Published by FapUNIFESP (SciELO) in Latin American Journal of Solids and Structures
- Vol. 18 (7)
An Associated and Nonassociated Flow Rule Comparison for AISI 439-430TI Forming: Modeling and Experimental Analysis
- 1 January 2021
- Published by FapUNIFESP (SciELO) in Latin American Journal of Solids and Structures
- Vol. 18 (7)
Open AccessAn Associated and Nonassociated Flow Rule Comparison for AISI 439-430TI Forming: Modeling and Experimental Analysis
- 17 September 2019
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 297, 31-50
Constitutive Modelling of an Industrial Rolled Sheet for a DIN 1623 St14 (DC04) Steel
The comprehension of the anisotropy impacts on mechanical properties of the rolled steel sheets was investigated using a non-quadratic anisotropic yield function. In this study, experimental and modelling determination of behavior of an industrial rolled sheets for a DIN 1623 St14 steel were carried out. The yield stresses and Lankford r-values in uniaxial were experimentally determined but the balanced biaxial tension stress states and rb were assumed. The parameters of the associated yield equation, derived from the three orthotropic yield functions proposed by Hill48 and Yld2000-2d, were determined. Predictions and the evolution of normalized yield stress and normalized Lankford parameters (plastic strain ratio) obtained by the presented investigative are considered. In order to describe the path of equivalent plastic behavior, the isotropic hardening function is described using the following various empirical standard formulae based on: Hollomon, Ludwick, Swift and Voce model.
- 17 September 2019
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 297, 31-50
Constitutive Modelling of an Industrial Rolled Sheet for a DIN 1623 St14 (DC04) Steel
The comprehension of the anisotropy impacts on mechanical properties of the rolled steel sheets was investigated using a non-quadratic anisotropic yield function. In this study, experimental and modelling determination of behavior of an industrial rolled sheets for a DIN 1623 St14 steel were carried out. The yield stresses and Lankford r-values in uniaxial were experimentally determined but the balanced biaxial tension stress states and rb were assumed. The parameters of the associated yield equation, derived from the three orthotropic yield functions proposed by Hill48 and Yld2000-2d, were determined. Predictions and the evolution of normalized yield stress and normalized Lankford parameters (plastic strain ratio) obtained by the presented investigative are considered. In order to describe the path of equivalent plastic behavior, the isotropic hardening function is described using the following various empirical standard formulae based on: Hollomon, Ludwick, Swift and Voce model.
- Open Access
- 1 January 2012
- Published by Surface Science Society Japan in e-Journal of Surface Science and Nanotechnology
- Vol. 10, 17
Erratum: An Investigation on the Usefulness and Performance of New Hot Working Tool Steel by Nitrocarburizing Process [e-J. Surf. Sci. Nanotech. Vol. 10, pp. 1-11 (2012)]
- 1 January 2012
- Published by Surface Science Society Japan in e-Journal of Surface Science and Nanotechnology
- Vol. 10, 17
Open AccessErratum: An Investigation on the Usefulness and Performance of New Hot Working Tool Steel by Nitrocarburizing Process [e-J. Surf. Sci. Nanotech. Vol. 10, pp. 1-11 (2012)]