Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Junsik Shin has a total of 14 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Development of a Portable Multimetric Sensing System for Bridge Load Testing and Load-Carrying Capacity Evaluation

    by Junyoung Park, Junsik Shin, Jongbin Won

    —Regular evaluation of bridge load-carrying capacity relies on static and dynamic load tests that measure vibration, strain, displacement, and neutral axis response. Conventional wired instrumentation is accurate but bulky, power demanding, and time consuming to deploy, which limits field efficiency and rapid verification of sensor quality. This study presents a portable, low-power multimetric measurement system that simultaneously acquires three-axis acceleration and four-channel strain and estimates displacement via multimetric data fusion. The hardware integrates a 24-bit ADC, a MEMS accelerometer, an RTC, on-board microSD storage, and Bluetooth Low Energy communication in a single module, while embedded firmware enables synchronized acquisition at 1000 Hz with filtering and downsampling. A mobile application provides trigger-based recording, real-time signal visualization, and broadcast time synchronization across multiple nodes without a base station. Laboratory tests show low noise levels (0.48 mg acceleration and 0.69 με strain) and multi-node timing differences within 0.05 s. Field validation was conducted on an in-service steel box girder bridge using a 15-ton truck for static load cases and dynamic passes at 10–70 km/h. Displacement estimated from synchronized strain and acceleration agreed with a co-located LVDT, with a maximum error below 0.1 mm. These results demonstrate that the proposed system enables efficient bridge load testing by providing synchronized multimetric measurements and on-site data quality assurance, supporting practical load-carrying capacity evaluation under field conditions while reducing effort and minimizing cabling-related signal degradation.

  • Open Access

    Cloud-Based Internet-of-Things System for Long-Term Bridge Bearing Monitoring Using Computer Vision

    by Gunhee Kim, Junsik Shin, Jongbin Won, Jongwoong Park

    Bearings play a crucial role in mitigating loads, maintaining stability, and transferring forces between superstructures and substructures. However, bearing failures caused by external factors can compromise structural safety. Therefore, continuous monitoring of bearing displacement is essential, yet current inspection methods are labor-intensive and unsuitable for long-term management. To address this, researchers have proposed systems such as Linear Variable Differential Transformers (LVDTs) and computer vision-based monitoring methods to track bearing displacement over time. However, reliance on external power sources and complex installation processes has limited their widespread application. This paper proposes an automated monitoring system integrating low-power IoT sensors, computer vision, and cloud computing. The system features an event-driven power mechanism to minimize energy consumption and utilizes vision-based displacement measurement techniques, providing both portability and efficiency. Applied in a real-world setting for nine months, the system successfully enabled the long-term monitoring of bridge bearings. The results demonstrate its effectiveness in overcoming traditional limitations and highlight its potential in supporting automated, data-driven assessments of structural stability.


  • Open Access

    Development of AI-Based Multisensory System for Monitoring Quay Wall Events

    by Junsik Shin, Junyoung Park, Jongbin Won, Jongwoong Park, Jiyoung Min

    Structural monitoring of quay walls, where various events occur due to unexpected high waves, vessels, and heavy equipment, is essential. However, real-time events cannot be constantly monitored by on-site personnel. To resolve the aforementioned issues, this study proposes an innovative AI-powered, cloud-based wireless sensor system that incorporates a high-sensitivity accelerometer with an ultra-low noise level of 0.003 mg, designed to monitor the low response amplitude of massive quay walls. The sensor can be activated by a scheduled trigger or a long-rangefinder. Vessel detection is performed utilizing the AI-based object detection method, Faster R-CNN, which employs ResNet as the backbone network. The detected anchor box’s position and dimensions are subsequently processed to confirm the presence of a berthing vessel. The collected data are then transmitted wirelessly to a proposed cloud server through LTE communication in real-time. The developed system was installed on a caisson-type quay wall in Korea, where acceleration, tilt, temperature, and camera image data were analyzed to assess its performance for real-time event monitoring. The results demonstrated that the safety of quay walls can be automatically managed by monitoring events during berthing and mooring with the proposed system.


  • Open Access

    Development of IoT Sensor and Cloud-based Server for Cloud-based Bridge Long-term Monitoring

    by Junyoung Park, Junsik Shin, Jongwoong Park

    As social infrastructures rapidly age, it is crucial to create a digital SOC (Social Overhead Capital) maintenance system for preventive maintenance. Using IoT sensors installed on the structures, abnormal signals produced by the structures may be rapidly identified and the best judgments can be made. In this study, a multimetric IoT sensor was integrated into a digital SOC monitoring system for long-term monitoring, use in a cloud computing server for automated and powerful data analysis, and for creating databases to perform: (1) multimetric sensing, (2) long-term operation, and (3) LTE-based direct communication. The created sensor included five strain sensing axes and three acceleration axes, and it also had an event-driven power management system that only turned on the sensors when the vibration reached a certain threshold or the timer started. Long-term operation might be made possible by the power management system and an extra solar panel charging. Real-time data transmission to the server from the sensors was accomplished using low-power LTE CAT.1 connection, which does not need an additional gateway device. Additionally, a displacement fusion technique was created on the cloud server to get reference-free structural displacement for ambient structural assessment after receiving multi-variable data from the sensor. A steel railroad and concrete girder bridge were used to experimentally evaluate the suggested digital SOC system.

  • Open Access

    Parametric codebook design for efficient signal transmission using uniform circular arrays

    by Junsik Shin, Junyeub Suh, Sangchun Park, Wonjin Sung

    In order to improve the quality of the received signal and system spectral efficiency, accurate beamforming using a given antenna array is essential for multiple-input multiple-output (MIMO) systems. To obtain desired MIMO transmission performance, construction of codebooks which are composed of matching beamforming vectors to the array structure is important. To effectively cover different types of mobile traffic, the base station for 5G new radio employs antenna arrays in various sizes and shapes. Nevertheless, the codebooks adopted by the 3GPP standard so far are based on the uniform linear array and the uniform planar array, necessitating design techniques for a wider class of antenna arrays. In this paper, we propose codebook construction methods for the uniform circular array with parameters to flexibly set the initial phase and step size based on the channel characteristics of the user equipment (UE). When tested over the 3GPP spatial channel model, the proposed codebooks show a substantial amount of gain over the conventional codebooks in all UE locations within the cell.


  • Open Access

    Development of a Reference-Free Indirect Bridge Displacement Sensing System

    by Jongbin Won, Jong-Woong Park, Junyoung Park, Junsik Shin, Minyong Park

    Bridge displacement measurements are important data for assessing the condition of a bridge. Measuring bridge displacement under moving vehicle loads is helpful for rating the load-carrying capacity and evaluating the structural health of a bridge. Displacements are conventionally measured using a linear variable differential transformer (LVDT), which needs stable reference points and thus prohibits the use of this method for measuring displacements for bridges crossing sea channels, large rivers, and highways. This paper proposes a reference-free indirect bridge displacement sensing system using a multichannel sensor board strain and accelerometer with a commercial wireless sensor platform (Xnode). The indirect displacement estimation method is then optimized for measuring the structural displacement. The performance of the developed system was experimentally evaluated on concrete- and steelbox girder bridges. In comparison with the reference LVDT data, the maximum displacement error for the proposed method was 2.17%. The proposed method was successfully applied to the displacement monitoring of a tall bridge (height = 20 m), which was very difficult to monitor using existing systems.


  • Open Access

    SSVM: An Ultra-Low-Power Strain Sensing and Visualization Module for Long-Term Structural Health Monitoring

    by Suleman Khan, Jongbin Won, Junsik Shin, Junyoung Park, Jong-Woong Park, Seung-Eock Kim, Yun Jang, Dong Joo Kim

    Structural health monitoring (SHM) is crucial for quantitative behavioral analysis of structural members such as fatigue, buckling, and crack propagation identification. However, formerly developed approaches cannot be implemented effectively for long-term infrastructure monitoring, owing to power inefficiency and data management challenges. This study presents the development of a high-fidelity and ultra-low-power strain sensing and visualization module (SSVM), along with an effective data management technique. Deployment of 24-bit resolution analog to a digital converter and precise half-bridge circuit for strain sensing are two significant factors for efficient strain measurement and power management circuit incorporating a low-power microcontroller unit (MCU), and electronic-paper display (EPD) enabled long-term operation. A prototype for SSVM was developed that performs strain sensing and encodes the strain response in a QR code for visualization on the EPD. For efficient power management, SSVM only activated when the trigger-signal was generated and stayed in power-saving mode consuming 18 mA and 337.9 μA, respectively. The trigger-signal was designed to be generated either periodically by a timer or intentionally by a push-button. A smartphone application and cloud database were developed for efficient data acquisition and management. A lab-scale experiment was carried out to validate the proposed system with a reference strain sensing system. A cantilever beam was deflected by increasing load at its free end, and the resultant strain response of SSVM was compared with the reference. The proposed system was successfully validated to use for long-term static strain measurement.