Maximilian Dobberkau
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Maximilian Dobberkau has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
Frank Atzler
Institute for Automotive Engineering Dresden, Chair of Combustion Engines and Powertrain Systems, Technical University of Dresden, Dresden, Germany
3 shared publicationsRonny Werner
TU Dresden Dresden Germany
3 shared publicationsAlfred Wiedensohler
Leibniz Institute for Tropospheric Research, Leipzig, Germany
1 shared publication- Frank Atzler
TU Dresden Dresden Germany
1 shared publication - Johannes Michael Voß
Faculty of Mechanical Engineering Ruhr‐University Bochum Bochum Germany
1 shared publication Kay Weinhold
Leibniz Institute for Tropospheric Research, Leipzig, Germany
1 shared publication
Latest Publications
- Open Access
- 2 September 2026
- Published by Wiley in Chemie Ingenieur Technik
Methanol With Increased Water Content in Internal Combustion Engines
This paper shows the advantages of methanol as a fuel and compares pure methanol (>99.9%) and methanol with a high‐water content (>18%) for use in an internal combustion engine. 18% water content is representative for methanol synthesized from hydrogen and industrial furnace gases as a carbon dioxide source. The achievable best point indicated efficiency is higher than 43% for both fuels. The increased water content of the low‐purity methanol is compensated by a longer injection time and can approximately be compared to a constant exhaust gas recirculation, which cannot be adjusted to the operating condition. Therefore, the best efficiency operation points are limited to a middle engine speed range and high load, which perfectly fits to a serial hybrid powertrain topology (Range Extender). The paper shows that additional energy that may be required for methanol distillation to high purity can be saved without losing combustion efficiency.
- 2 September 2026
- Published by Wiley in Chemie Ingenieur Technik
Open AccessMethanol With Increased Water Content in Internal Combustion Engines
This paper shows the advantages of methanol as a fuel and compares pure methanol (>99.9%) and methanol with a high‐water content (>18%) for use in an internal combustion engine. 18% water content is representative for methanol synthesized from hydrogen and industrial furnace gases as a carbon dioxide source. The achievable best point indicated efficiency is higher than 43% for both fuels. The increased water content of the low‐purity methanol is compensated by a longer injection time and can approximately be compared to a constant exhaust gas recirculation, which cannot be adjusted to the operating condition. Therefore, the best efficiency operation points are limited to a middle engine speed range and high load, which perfectly fits to a serial hybrid powertrain topology (Range Extender). The paper shows that additional energy that may be required for methanol distillation to high purity can be saved without losing combustion efficiency.
- Open Access
- 29 August 2025
- Published by Springer Nature in Automotive and Engine Technology
- Vol. 10 (1) , 1-11
Methanol cold start procedure for a serial hybrid powertrain
Green methanol is a renewable fuel with many advantages when used in a spark ignition combustion process. Methanol has a comparatively high enthalpy of vaporization, leading to lower combustion temperatures (compared to gasoline combustion) and, hence, lower wall heat losses as well as a reduced tendency to pre-ignition. Therefore, a brake efficiency of more than 40% and, furthermore, minimal emissions are possible. The serial combination of a combustion engine with an electric powertrain provides a disconnection of the load demand of the powertrain and the operating point of the combustion engine. In this case, a high volumetric and gravimetric power density, easy energy storage, and a very cost effective already existing infrastructure of fuel distribution is combined with electric driving, high efficiencies, minimal emissions and a closed carbon cycle for the energy provision. Nevertheless, the high flash point of methanol at 11 °C indicates a challenging cold start. Heating the fuel or intake air or blending lightly boiling components are feasible solutions, but are related to additional expenses regarding packaging and cost. The described procedure enables the cold start of pure methanol down to −20 °C, without the necessity for additional engine components, when using a serial hybrid propulsion system. Besides, a serial hybrid powertrain offers the possibility of preheating the exhaust aftertreatment in addition to a reliable methanol cold start, while the vehicle is already running on its electric power train.
- 29 August 2025
- Published by Springer Nature in Automotive and Engine Technology
- Vol. 10 (1) , 1-11
Open AccessMethanol cold start procedure for a serial hybrid powertrain
Green methanol is a renewable fuel with many advantages when used in a spark ignition combustion process. Methanol has a comparatively high enthalpy of vaporization, leading to lower combustion temperatures (compared to gasoline combustion) and, hence, lower wall heat losses as well as a reduced tendency to pre-ignition. Therefore, a brake efficiency of more than 40% and, furthermore, minimal emissions are possible. The serial combination of a combustion engine with an electric powertrain provides a disconnection of the load demand of the powertrain and the operating point of the combustion engine. In this case, a high volumetric and gravimetric power density, easy energy storage, and a very cost effective already existing infrastructure of fuel distribution is combined with electric driving, high efficiencies, minimal emissions and a closed carbon cycle for the energy provision. Nevertheless, the high flash point of methanol at 11 °C indicates a challenging cold start. Heating the fuel or intake air or blending lightly boiling components are feasible solutions, but are related to additional expenses regarding packaging and cost. The described procedure enables the cold start of pure methanol down to −20 °C, without the necessity for additional engine components, when using a serial hybrid propulsion system. Besides, a serial hybrid powertrain offers the possibility of preheating the exhaust aftertreatment in addition to a reliable methanol cold start, while the vehicle is already running on its electric power train.
- Open Access
- 31 July 2024
- Published by Wiley in Chemie Ingenieur Technik
- Vol. 96 (9) , 1196-1202
Methanol, the ICE Green Maker
Green methanol is a renewable fuel with great advantages when used in a spark ignition combustion process. Methanol has a comparatively high enthalpy of vaporization, leading to lower combustion temperatures as compared to gasoline combustion, and, hence, lower wall heat losses as well as a reduced tendency to pre‐ignition. Therefore, a brake efficiency of more than 40 % (this is comparable to diesel engines!) and furthermore minimal emissions, even at cold start, are possible. The serial combination with an electric powertrain provides a disconnection of the load demand of the powertrain and the operating point of the combustion engine. In this case, a high volumetric and gravimetric power density, easy energy storage and proven infrastructure of fuel distribution are combined with electric driving, high efficiencies, minimal emissions, and a closed carbon cycle for the energy provision.
- 31 July 2024
- Published by Wiley in Chemie Ingenieur Technik
- Vol. 96 (9) , 1196-1202
Open AccessMethanol, the ICE Green Maker
Green methanol is a renewable fuel with great advantages when used in a spark ignition combustion process. Methanol has a comparatively high enthalpy of vaporization, leading to lower combustion temperatures as compared to gasoline combustion, and, hence, lower wall heat losses as well as a reduced tendency to pre‐ignition. Therefore, a brake efficiency of more than 40 % (this is comparable to diesel engines!) and furthermore minimal emissions, even at cold start, are possible. The serial combination with an electric powertrain provides a disconnection of the load demand of the powertrain and the operating point of the combustion engine. In this case, a high volumetric and gravimetric power density, easy energy storage and proven infrastructure of fuel distribution are combined with electric driving, high efficiencies, minimal emissions, and a closed carbon cycle for the energy provision.
- Open Access
- 10 November 2021
- Published by Springer Nature in Automotive and Engine Technology
- Vol. 7 (1-2) , 15-26
Roller dynamometer particle immission* measurement
Urban traffic is a significant contributor of particulate matter to the environment (Kessinger et al. in https://www.umweltbundesamt.de/sites/default/files/medien/5750/publikationen/hgp_luftqualitaet_2020_bf.pdf, 2021). Hence, there is a high interest in the measured data of roadside immission measurement station. In the federal state Saxony (Germany), the State Office for Environment, Agriculture and Geology (LfULG) is responsible for supervision of the air pollution. In a joint project, the LfULG, the Leibniz Institute for Tropospheric Research (TROPOS) and the Chair of Combustion Engines and Powertrain Systems of the Technical University of Dresden (Lehrstuhl für Verbrennungsmotoren und Antriebssysteme, LVAS) measured the particulate immission* from a selection of passenger cars in an “environment simulation” Weinhold et al. (https://publikationen.sachsen.de/bdb/artikel/36768q, 2020). Especially direct injection spark ignition engines, DISI, without particle filter have a high particulate matter emission, depending on the operating condition. However, an increase of the particulate matter immission due to the rising market penetration of DISI engines was not measurable at the immission measurement stations of LfULG. To investigate the effect of vehicle exhaust emission and immission, an experiment was developed to measure particulate matter immission similar to road conditions on a chassis dynamometer. Five used cars with different engines, exhaust after treatment systems and mileage were evaluated regarding their emissions and particulate immissions. Unexpectedly, a high amount of ultrafine particulate matter smaller 100 nm was found during the emission measurements, although the exhaust emissions were completely extracted to the CVS measurement system. It was concluded that these particles were assignable to break and tire wear. This paper summarizes the most important findings, the complete report is available in Weinhold et al. (https://publikationen.sachsen.de/bdb/artikel/36768q, 2020).
- 10 November 2021
- Published by Springer Nature in Automotive and Engine Technology
- Vol. 7 (1-2) , 15-26
Open AccessRoller dynamometer particle immission* measurement
Urban traffic is a significant contributor of particulate matter to the environment (Kessinger et al. in https://www.umweltbundesamt.de/sites/default/files/medien/5750/publikationen/hgp_luftqualitaet_2020_bf.pdf, 2021). Hence, there is a high interest in the measured data of roadside immission measurement station. In the federal state Saxony (Germany), the State Office for Environment, Agriculture and Geology (LfULG) is responsible for supervision of the air pollution. In a joint project, the LfULG, the Leibniz Institute for Tropospheric Research (TROPOS) and the Chair of Combustion Engines and Powertrain Systems of the Technical University of Dresden (Lehrstuhl für Verbrennungsmotoren und Antriebssysteme, LVAS) measured the particulate immission* from a selection of passenger cars in an “environment simulation” Weinhold et al. (https://publikationen.sachsen.de/bdb/artikel/36768q, 2020). Especially direct injection spark ignition engines, DISI, without particle filter have a high particulate matter emission, depending on the operating condition. However, an increase of the particulate matter immission due to the rising market penetration of DISI engines was not measurable at the immission measurement stations of LfULG. To investigate the effect of vehicle exhaust emission and immission, an experiment was developed to measure particulate matter immission similar to road conditions on a chassis dynamometer. Five used cars with different engines, exhaust after treatment systems and mileage were evaluated regarding their emissions and particulate immissions. Unexpectedly, a high amount of ultrafine particulate matter smaller 100 nm was found during the emission measurements, although the exhaust emissions were completely extracted to the CVS measurement system. It was concluded that these particles were assignable to break and tire wear. This paper summarizes the most important findings, the complete report is available in Weinhold et al. (https://publikationen.sachsen.de/bdb/artikel/36768q, 2020).