Huanan Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Huanan Wang has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Wenxiang Zhao
Nanjing Institute of Technology
8 shared publications - Tao Tao
Jiangsu University
3 shared publications - Liang Xu
School of Electrical and Information Engineering, Jiangsu University, Zhenjiang, China
2 shared publications Tao Tao
School of Electrical and Information Engineering, Jiangsu University, Zhenjiang, China
2 shared publications- Tingting Jiang
School of Electrical and Information Engineering, Jiangsu University, Zhenjiang, China
2 shared publications - Christopher H. T. Lee
Nanyang Technological University
1 shared publication
Latest Publications
- 7 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 73 (3) , 4552-4562
Carrier Phase Shift Control to Reduce Iron Loss in Nine-Phase Cobalt–Iron PMSMs
Cobalt–iron multiphase permanent magnet synchronous motors (PMSMs) exhibit superior electromagnetic performance but induce elevated iron loss, especially under high-modulation index condition. This article investigates a carrier phase shift-based control scheme for nine-phase cobalt–iron PMSMs in order to mitigate high-frequency harmonic currents and reduce iron loss. First, the effect of high-frequency harmonic currents on iron loss is systematically analyzed under varied conditions. Afterward, the first-, second-, third-, and fourth-sideband harmonic currents are derived with varying modulation index. Under high-modulation index condition, the first-sideband harmonic currents, which have much larger amplitude than the second, third, and fourth, are found to play a critical role in reducing iron loss. Subsequently, a targeted sideband harmonic currents cancelation method is developed. Theoretical analysis identifies an optimal 8$\boldsymbol{\pi}$/9 carrier phase shift between three modules for mitigating the first-sideband harmonic currents. Therefore, the iron loss under high-modulation index can be reduced effectively. Finally, experimental results verify that the proposed control scheme can achieve high-frequency harmonic currents mitigation and iron loss reduction.
- 7 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 73 (3) , 4552-4562
Carrier Phase Shift Control to Reduce Iron Loss in Nine-Phase Cobalt–Iron PMSMs
Cobalt–iron multiphase permanent magnet synchronous motors (PMSMs) exhibit superior electromagnetic performance but induce elevated iron loss, especially under high-modulation index condition. This article investigates a carrier phase shift-based control scheme for nine-phase cobalt–iron PMSMs in order to mitigate high-frequency harmonic currents and reduce iron loss. First, the effect of high-frequency harmonic currents on iron loss is systematically analyzed under varied conditions. Afterward, the first-, second-, third-, and fourth-sideband harmonic currents are derived with varying modulation index. Under high-modulation index condition, the first-sideband harmonic currents, which have much larger amplitude than the second, third, and fourth, are found to play a critical role in reducing iron loss. Subsequently, a targeted sideband harmonic currents cancelation method is developed. Theoretical analysis identifies an optimal 8$\boldsymbol{\pi}$/9 carrier phase shift between three modules for mitigating the first-sideband harmonic currents. Therefore, the iron loss under high-modulation index can be reduced effectively. Finally, experimental results verify that the proposed control scheme can achieve high-frequency harmonic currents mitigation and iron loss reduction.
- 30 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 72 (11) , 11587-11601
Open-Leg Fault-Tolerant Control and Comparative Postfault Performance Analysis for Five-Phase Series-End Winding PMSM
Compared with the Y-connection topology in five-phase motor drive, the open-leg fault will lead to unique postfault characteristics in series-end winding (SEW) topology, for which the most common used winding connection sequence (WCS) of ADBEC will lose the advantage of large speed range. This article newly proposes the open-leg fault-tolerant control for five-phase SEW permanent-magnet synchronous motor. First, the open-leg fault is divided into two types in SEW topology. For the type II fault, in terms of different postfault targets such as minimum copper loss and maximum torque, the harmonic current references are firstly derived for different WCSs. Then, the voltage compensation scheme is adopted to achieve the desired fault-tolerant currents. Subsequently, the postfault performance indicators are comparatively analyzed across different WCSs. It is concluded that under type II faulty condition, WCS of ABCDE can achieve the smaller fault-tolerant currents, less copper loss and same speed range comparing with ADBEC. In addition, the postfault performances of both type I and II faults are also theoretically compared with Y-connection and pentagon topologies. The experimental results are presented to verify the analysis and the conclusions, which can provide more basis for selecting which WCS in practical application of SEW topology.
- 30 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 72 (11) , 11587-11601
Open-Leg Fault-Tolerant Control and Comparative Postfault Performance Analysis for Five-Phase Series-End Winding PMSM
Compared with the Y-connection topology in five-phase motor drive, the open-leg fault will lead to unique postfault characteristics in series-end winding (SEW) topology, for which the most common used winding connection sequence (WCS) of ADBEC will lose the advantage of large speed range. This article newly proposes the open-leg fault-tolerant control for five-phase SEW permanent-magnet synchronous motor. First, the open-leg fault is divided into two types in SEW topology. For the type II fault, in terms of different postfault targets such as minimum copper loss and maximum torque, the harmonic current references are firstly derived for different WCSs. Then, the voltage compensation scheme is adopted to achieve the desired fault-tolerant currents. Subsequently, the postfault performance indicators are comparatively analyzed across different WCSs. It is concluded that under type II faulty condition, WCS of ABCDE can achieve the smaller fault-tolerant currents, less copper loss and same speed range comparing with ADBEC. In addition, the postfault performances of both type I and II faults are also theoretically compared with Y-connection and pentagon topologies. The experimental results are presented to verify the analysis and the conclusions, which can provide more basis for selecting which WCS in practical application of SEW topology.
- 5 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (6) , 8528-8539
Phase Current Reconstruction for DTP-PMSM With Single Current Sensor Using Synchronous Filtering Reconstruction Method
In dual three-phase permanent magnet synchronous motor (DTP-PMSM) drive, six-phase current information is critical to motor control. However, the adoption of multiple current sensors increases the size and cost of inverters. To mitigate this issue, this article proposes a method to reconstruct six-phase currents of a DTP-PMSM by using a single current sensor (SCS). First, the SCS is repositioned to a current branch. Then, sampling is performed twice in one period based on the switching state of a single bridge arm. Therefore, two orthogonal phase currents are achieved. Furthermore, the synchronous filtering reconstruction method is proposed. Through this method, the harmonic current information is extracted from two orthogonal currents and the remaining four-phase currents are reconstructed. Overall, six-phase currents can be accurately reconstructed by using an SCS, for which the hardware cost and inverter size can be reduced. The proposed method is validated by both simulation and experiments.
- 5 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (6) , 8528-8539
Phase Current Reconstruction for DTP-PMSM With Single Current Sensor Using Synchronous Filtering Reconstruction Method
In dual three-phase permanent magnet synchronous motor (DTP-PMSM) drive, six-phase current information is critical to motor control. However, the adoption of multiple current sensors increases the size and cost of inverters. To mitigate this issue, this article proposes a method to reconstruct six-phase currents of a DTP-PMSM by using a single current sensor (SCS). First, the SCS is repositioned to a current branch. Then, sampling is performed twice in one period based on the switching state of a single bridge arm. Therefore, two orthogonal phase currents are achieved. Furthermore, the synchronous filtering reconstruction method is proposed. Through this method, the harmonic current information is extracted from two orthogonal currents and the remaining four-phase currents are reconstructed. Overall, six-phase currents can be accurately reconstructed by using an SCS, for which the hardware cost and inverter size can be reduced. The proposed method is validated by both simulation and experiments.
- 16 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 11 (2) , 6775-6787
Low-Vibration Fault-Tolerant Control for Five-Phase PMSM Using Modified SVPWM and Random Modulation Strategy
Vibration issues due to open-circuit faults have been overlooked by existing fault-tolerant control methods. To reduce vibrations in five-phase permanent magnet synchronous motors (PMSMs) under open-circuit fault conditions, a low-vibration fault-tolerant control method using modified space vector pulsewidth modulation (SVPWM) and random switching frequency (RSF) SVPWM is proposed. Virtual voltage vectors for the faulty PMSM are reconstructed using basic vectors with the constraint of zero harmonic spatial components. The action time of the virtual voltage vectors, considering the back electromotive force (EMF) of the faulty phase, is then calculated. To suppress high-frequency harmonics without compromising the fault-tolerant performance of the motor, a new RSF-SVPWM with restricted random numbers and improved probability density is proposed. By combining the modified SVPWM with the RSF-SVPWM, the proposed method can reduce vibration while maintaining good fault-tolerant performance. Experimental results validate the feasibility of the control strategy.
- 16 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 11 (2) , 6775-6787
Low-Vibration Fault-Tolerant Control for Five-Phase PMSM Using Modified SVPWM and Random Modulation Strategy
Vibration issues due to open-circuit faults have been overlooked by existing fault-tolerant control methods. To reduce vibrations in five-phase permanent magnet synchronous motors (PMSMs) under open-circuit fault conditions, a low-vibration fault-tolerant control method using modified space vector pulsewidth modulation (SVPWM) and random switching frequency (RSF) SVPWM is proposed. Virtual voltage vectors for the faulty PMSM are reconstructed using basic vectors with the constraint of zero harmonic spatial components. The action time of the virtual voltage vectors, considering the back electromotive force (EMF) of the faulty phase, is then calculated. To suppress high-frequency harmonics without compromising the fault-tolerant performance of the motor, a new RSF-SVPWM with restricted random numbers and improved probability density is proposed. By combining the modified SVPWM with the RSF-SVPWM, the proposed method can reduce vibration while maintaining good fault-tolerant performance. Experimental results validate the feasibility of the control strategy.
- 26 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 37 (1) , 210-219
Improved Fault-Tolerant Model Predictive Torque Control of Five-Phase PMSM by Using Deadbeat Solution
This paper proposes an improved fault-tolerant model predictive torque control (MPTC) for a five-phase permanent magnet synchronous motor based on deadbeat solution, which offers the reduced computation burden, good steady-state performance and simple control structure. Under the open-circuit fault condition, the virtual voltage vectors (VVV) which can restrain the harmonics work as the candidate vectors. The deadbeat solution is adopted to predict the reference voltage vector. The optimal VVV can be selected directly and rapidly according to the sector of the reference voltage vector. Hence the computation burden can be reduced largely because the process of testing all candidate VVVs is avoided. In order to reduce the error between the reference voltage vector and the selected VVV, a null vector is introduced by a simple geometric principle. Then, the duration of the selected VVV can be obtained. Therefore, the steady-state performance is enhanced because of the deadbeat solution and the multi-vectors in each control period. The experiments are presented to verify the proposed fault-tolerant MPTC.
- 26 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 37 (1) , 210-219
Improved Fault-Tolerant Model Predictive Torque Control of Five-Phase PMSM by Using Deadbeat Solution
This paper proposes an improved fault-tolerant model predictive torque control (MPTC) for a five-phase permanent magnet synchronous motor based on deadbeat solution, which offers the reduced computation burden, good steady-state performance and simple control structure. Under the open-circuit fault condition, the virtual voltage vectors (VVV) which can restrain the harmonics work as the candidate vectors. The deadbeat solution is adopted to predict the reference voltage vector. The optimal VVV can be selected directly and rapidly according to the sector of the reference voltage vector. Hence the computation burden can be reduced largely because the process of testing all candidate VVVs is avoided. In order to reduce the error between the reference voltage vector and the selected VVV, a null vector is introduced by a simple geometric principle. Then, the duration of the selected VVV can be obtained. Therefore, the steady-state performance is enhanced because of the deadbeat solution and the multi-vectors in each control period. The experiments are presented to verify the proposed fault-tolerant MPTC.
- 2 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 7 (4) , 2635-2644
Model Predictive Torque Control of Five-Phase PMSM by Using Double Virtual Voltage Vectors Based on Geometric Principle
The conventional model predictive torque control (MPTC) suffers from the heavy computation burden and the uncertainty of the weighting factor. This article proposed a new MPTC scheme for a five-phase permanent magnet synchronous motor by using double virtual voltage vectors (VVVs), in which no weighting factor is required. The VVVs that can restrain the harmonics work as the candidate vectors. The deadbeat principle is adopted to predict the reference voltage, which can be used to select the optimal VVV directly in avoid of testing all candidate VVVs, and hence, the computation burden is reduced. The geometric principle is applied to select the second voltage vector and calculate the vector duration. The second vector can be a VVV or null vector. Therefore, double VVVs or a VVV and a null vector can be synthesized for the next period. It should be noted that no weighting factor is required because of the introduced geometric principle. Due to the selection of the second voltage vector, the torque and flux ripples are reduced and the steady-state performance is improved. The proposed MPTC has the same fast dynamic response with the conventional MPTC. The experiments are presented to verify the proposed MPTC scheme.
- 2 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 7 (4) , 2635-2644
Model Predictive Torque Control of Five-Phase PMSM by Using Double Virtual Voltage Vectors Based on Geometric Principle
The conventional model predictive torque control (MPTC) suffers from the heavy computation burden and the uncertainty of the weighting factor. This article proposed a new MPTC scheme for a five-phase permanent magnet synchronous motor by using double virtual voltage vectors (VVVs), in which no weighting factor is required. The VVVs that can restrain the harmonics work as the candidate vectors. The deadbeat principle is adopted to predict the reference voltage, which can be used to select the optimal VVV directly in avoid of testing all candidate VVVs, and hence, the computation burden is reduced. The geometric principle is applied to select the second voltage vector and calculate the vector duration. The second vector can be a VVV or null vector. Therefore, double VVVs or a VVV and a null vector can be synthesized for the next period. It should be noted that no weighting factor is required because of the introduced geometric principle. Due to the selection of the second voltage vector, the torque and flux ripples are reduced and the steady-state performance is improved. The proposed MPTC has the same fast dynamic response with the conventional MPTC. The experiments are presented to verify the proposed MPTC scheme.
- 1 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 7 (4) , 2787-2797
Investigation Into Multitoothed Distribution Design for Magnetless Doubly Salient Machine
In the design of magnetless multitoothed doubly salient (DS) machine, most multitoothed structures are regarded as uniform distribution, while the influence of multitoothed distribution on performance is ignored. This article investigates the design of magnetless DS machine with consideration of multitoothed distribution. Analytical expressions, including magnetomotive force, permeance modulation, air-gap flux density, flux linkage, and back electromotive force, are derived to reveal the mechanism of multitoothed distribution. Then, different multitoothed distribution models are optimized through a genetic algorithm combined with a finite-element method for maximum torque and reduced torque ripple. It is found that with the consideration of multitoothed distribution design, a ~20% torque improvement is achieved in the machine. Finally, the effectiveness of the theoretical analysis and multitoothed distribution design is validated by finite-element simulation and experiments.
- 1 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 7 (4) , 2787-2797
Investigation Into Multitoothed Distribution Design for Magnetless Doubly Salient Machine
In the design of magnetless multitoothed doubly salient (DS) machine, most multitoothed structures are regarded as uniform distribution, while the influence of multitoothed distribution on performance is ignored. This article investigates the design of magnetless DS machine with consideration of multitoothed distribution. Analytical expressions, including magnetomotive force, permeance modulation, air-gap flux density, flux linkage, and back electromotive force, are derived to reveal the mechanism of multitoothed distribution. Then, different multitoothed distribution models are optimized through a genetic algorithm combined with a finite-element method for maximum torque and reduced torque ripple. It is found that with the consideration of multitoothed distribution design, a ~20% torque improvement is achieved in the machine. Finally, the effectiveness of the theoretical analysis and multitoothed distribution design is validated by finite-element simulation and experiments.