OGOleksandr Glitin

Oleksandr Glitin

*This is an algorithmically generated author record based on publicly available information.

Oleksandr Glitin has a total of 9 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Assessment of the fire resistance of a flanged joint of a steel truss

    by Yevhen Tsiupyn, Oleksandr Glitin, Serhii Radetskyi

    The article considers the specific features of the numerical assessment of the fire resistance of a spatial joint connecting tubular elements with a ring flange and radial stiffening ribs. The relevance of the study is due to the fact that, in steel structures under fire conditions, the limit state is often governed not by the overall strength of the main cross-section, but by the local behavior of joints, where a complex interaction occurs between the base metal, welds, bolts, contact zones, and stiffeners. It is precisely the joints that are the most sensitive to the reduction in the physical and mechanical properties of the material when heated, since stresses are concentrated in them, the force transfer pattern changes, and local failure mechanisms manifest themselves more rapidly. The aim of the study is to determine the influence of the fire-protective layer on the temperature regime and load-bearing capacity of the investigated joint under standard fire exposure in accordance with the R60 fire resistance requirement. The study was carried out in two successive stages. At the first stage, a fire analysis of the joint without fire protection was performed using the following initial parameters: the standard fire curve, convective heat transfer coefficient αc = 25 W/m²K, steel surface emissivity εm = 0.80, and fire environment emissivity εf = 1.00. The analysis showed intensive heating of the joint components to temperatures of approximately 935.86-942.88°C. However, after the introduction of contour fire protection with the following parameters: layer thickness dp = 30 mm, thermal conductivity λp = 0.2 W/(m•K), specific heat capacity cp = 1700 J/(kg•K), and density ρp = 800 kg/m³, the temperature decreased to the range of 221.43-380.97°C.

  • An effective method for strengthening steel beams and purlins using an elastic support in the span

    by Oleksandr Glitin, Serhii Bilyk, Serhii Radetskyi, Oleh Sonko, Oleksii Kravchenko

    The article is devoted to the development of theoretical approaches to strengthening bending elements, such as beams and girders, through the installation of an elastic support at the midpoint of the span where the maximum bendingmoment occurs, as well as the development of a practical calculation method for such reinforcement. The need for strengthening may arise under various conditions, including prolonged operation beyond the design lifespan, increased service loads on existing structures, wear and tear of structures, or damage caused by episodic additional loads (e.g.,earthquakes, explosions). The purpose of the study is to provide a practical method for reinforcing girders and beams using an elastic support at the span to increase the load-bearing capacity of structures under increased loads (e.g., installation of solar power stations or other additional equipment on roofs) or in cases of damage caused by explosions or other episodic loads that reduce the cross-sectional geometric characteristics and require rapid strengthening. The article proposes a calculation methodology for this type of reinforcement that addresses shortcomings in existing scientific and technical literature and facilitates the broader implementation of the method to enhance the reliability of structures.The article presents an effective method for reinforcing girders and beams in response to increased loading. Using an elastic support (brace) at the span enhances the load-bearing capacity of structures.The method involves installing a brace under the element to be strengthened, secured with additional bolts to create an elastic support that reduces the applied load. This solution eliminates the need for welding or disrupting the structural integrity. Atechnological gap is provided to create pre-stressing, which is closed during bolt tightening. The main advantages include minimal intervention, pre-stressing creation, and increased structural reliability. The article contains a calculation methodology for this reinforcement method, promoting its practical application to improve the efficiency and reliability of structures.The proposed reinforcement method is demonstrated on steel structures but can be extended, if necessary, to structures made of other materials, such as wood or reinforced concrete.

  • Open Access

    OPTIMAL HEIGHT OF STEEL I-BEAMS WITH CHANGING THE WIDTH OF THE FLANGES

    by Artem Bilyk, Sergio Bilyk, Oleksandr Glitin, Lubomir Dzhanov, Артем Білик, Сергій Білик

    The article improves the methodological approach to finding the best constructive solution for a beam made of welded steel I-beams with a variable flange width. An idealized physicalmathematical model of the construction of a beam made of welded steel I-beams with a tapered flange depending on the consumption of steel and changes in the geometric characteristics of the cross-section is described. The bending strength conditions of the beam are taken as limitations. The purpose of the research was to develop an approach to establish the regularity of a rational constructive solution depending on the variability of the width of the flanges of the elastic steel I-beam along its length.It is shown that determining the pattern of changes in the stress-strain state of steel beams with variable shelf width at a constant cross-section height is an urgent task. As a result on the optimal consumption of steel for the structure is shown. A pattern hasbeen established between the variable parameter of the width of the flanges and the coordinate of the calculated section. The effect of displacement of the calculated section of the beams in the direction of a decrease in the geometric characteristics of thebeams, depending on the degree of variability of the width of the shelf along the length of the beam, has been confirmed. Thus, in beams with a variable shelf width at a constant wall height, the maximum stresses occur in the cross-section that does not havethe maximum geometric characteristics.Analytical dependences of determining the optimal height depending on the variability of the width of the flanges were obtained. The methodology of research in the search for a rationalconstructive solution is described. It is shown that in the case of the variability of the width of the flanges, the parameter of the optimal height of the beam depends on the load distribution unction along the length of the beam.A cantilever-clamped elastic beam of I-beam cross-section was studied. Through the relative parameter of the variability of geometric characteristics, it is shown that when the parameterof the variability of the shelf width is changed, the calculated cross-section moves toward the free end with smaller geometric characteristics.Corresponding numerical studies have been carried out, which are illustrated by graphs. The conducted research allows choosing theoptimal dimensions of a steel welded I-beam by changing the width of the flanges that perceive bending moments. According to the research results, the degree of variability of the cross-sectionis recommended for rational designs of steel Ibeams by changing the width of the flanges.


  • Open Access

    Modeling of physical wear assessment of zinc coating of space steel frame road structures for road safety information systems

    by Serhiy Bilyk, Artem Bilyk, Eugen Tsyupyn, Oleksandr Glitin

    The article developed an improved physical and mathematical model of the corrosive wear of zinc coating of steel structures in a city. The research is based on full-scale experimental data for determining the wear of a zinc coating of full-scale metal spatial structures of frame road structures for informational safety systems on roads after 10 years of operation in the conditions of Kyiv. The frame structure consists of metal columns and a steel crossbar frame. The crossbar frame is a spatial block of two steel trusses. The block of trusses is assembled from unified spatial sections united by vertical and horizontal ties, and which are connected by flange nodes of a special design. All structural elements are made of rolled tubes. Based on the research results, an approach to assessing the physical wear of the zinc coating of the spatial structural system is proposed. According to the peculiarities of the arrangement of elements in frame structures, and, accordingly, to different conditions and operations, an approach is proposed to assess the corrosive wear of a zinc coating for various groups of elements: columns, spatial block of two steel trusses, flange nodes. The physical and mathematical model is based on the working hypothesis of uneven wear of the zinc coating over time. It was found that for each group of structural elements, the conditions of the gaseous environment, the effects of atmospheric precipitation, wind speed, temperature changes individually affect the reduction of the zinc coating. The obtained experimental data were used to determine the parameter of the rate of decrease in the zinc coating of the physical and mathematical model. The results of the research and the development of the methodology helped to establish the operating conditions of the zinc coating according to the criterion of the rate of wear of the zinc coating, to classify the category of aggressiveness of the environment for each group of structural elements. Also, studies allow predicting the service life by reducing the thickness of the zinc coating, as well as the wear of the zinc coating in time in the subsequent period of operation. The methodology is universal and can be extended to other types of galvanized metal structures.