Yevhen Tsiupyn
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yevhen Tsiupyn has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Oleksandr Glitin2 shared publications
- Andrii Kozak
Kyiv National University of Construction and Architecture
1 shared publication - Artem Bilyk
Kyiv National University of Construction and Architecture
1 shared publication - Olha Bashynska
National Aviation University
1 shared publication - Serhii Bilyk
Kyiv National University of Construction and Architecture
1 shared publication - Serhii Radetskyi1 shared publication
Latest Publications
- Open Access
- 28 May 2026
- Published by Kyiv National University of Construction and Architecture in Strength of Materials and Theory of Structures
- No. 116
Assessment of the effect of the fluctuating component of wind pressure on a lattice telecommunication tower
The paper presents a calculation methodology for accounting for the fluctuating component of wind loading in the analysis of a spatial lattice telecommunication tower 50 m high, designed according to a modular concept (2.0 m vertical module) with plan-dimension changes along the height. Unlike the standard approach, where the dynamic coefficient is taken as an input multiplier, a methodology based on the peak response parameter is proposed. In this methodology, the equivalent dynamic coefficient is determined by the criterion of the structure’s peak response (top displacement, base bending moment, or critical axial force), and the distribution of equivalent nodal forces is formed so as to ensure equality of the generalized modal force in the first vibration mode. The matrix form of the equations of motion is given in full as , with derivation of the element stiffness and mass matrices of a spatial truss element and rules for assembling the global matrices. An algorithm is proposed for piecewise formation of the equivalent wind load over the height intervals 0–32, 32–34, 34–44, 44–46, and 46–50 m, converting pressure to forces through the effective projected area of the lattice. The methodology provides a physically justified consideration of the fluctuating component without direct time-history simulation of the wind process and improves the reproducibility of calculation results. In addition, the choice of the first mode as dominant for the along-wind response is substantiated, and procedural checks of load consistency are provided through equality of the generalized modal force. It is shown that the piecewise discretization enables correct consideration of structural transitions and differences in «wind-exposed area» along the height, while the use of the effective projected area reduces subjectivity when modeling permeable lattice systems. A control criterion is proposed: and , which guarantees convergence with respect to the selected response quantity.
- 28 May 2026
- Published by Kyiv National University of Construction and Architecture in Strength of Materials and Theory of Structures
- No. 116
Open AccessAssessment of the effect of the fluctuating component of wind pressure on a lattice telecommunication tower
The paper presents a calculation methodology for accounting for the fluctuating component of wind loading in the analysis of a spatial lattice telecommunication tower 50 m high, designed according to a modular concept (2.0 m vertical module) with plan-dimension changes along the height. Unlike the standard approach, where the dynamic coefficient is taken as an input multiplier, a methodology based on the peak response parameter is proposed. In this methodology, the equivalent dynamic coefficient is determined by the criterion of the structure’s peak response (top displacement, base bending moment, or critical axial force), and the distribution of equivalent nodal forces is formed so as to ensure equality of the generalized modal force in the first vibration mode. The matrix form of the equations of motion is given in full as , with derivation of the element stiffness and mass matrices of a spatial truss element and rules for assembling the global matrices. An algorithm is proposed for piecewise formation of the equivalent wind load over the height intervals 0–32, 32–34, 34–44, 44–46, and 46–50 m, converting pressure to forces through the effective projected area of the lattice. The methodology provides a physically justified consideration of the fluctuating component without direct time-history simulation of the wind process and improves the reproducibility of calculation results. In addition, the choice of the first mode as dominant for the along-wind response is substantiated, and procedural checks of load consistency are provided through equality of the generalized modal force. It is shown that the piecewise discretization enables correct consideration of structural transitions and differences in «wind-exposed area» along the height, while the use of the effective projected area reduces subjectivity when modeling permeable lattice systems. A control criterion is proposed: and , which guarantees convergence with respect to the selected response quantity.
- Open Access
- 28 May 2026
- Published by Kyiv National University of Construction and Architecture in Building constructions. Theory and Practice
- No. 18
Assessment of the fire resistance of a flanged joint of a steel truss
The article considers the specific features of the numerical assessment of the fire resistance of a spatial joint connecting tubular elements with a ring flange and radial stiffening ribs. The relevance of the study is due to the fact that, in steel structures under fire conditions, the limit state is often governed not by the overall strength of the main cross-section, but by the local behavior of joints, where a complex interaction occurs between the base metal, welds, bolts, contact zones, and stiffeners. It is precisely the joints that are the most sensitive to the reduction in the physical and mechanical properties of the material when heated, since stresses are concentrated in them, the force transfer pattern changes, and local failure mechanisms manifest themselves more rapidly. The aim of the study is to determine the influence of the fire-protective layer on the temperature regime and load-bearing capacity of the investigated joint under standard fire exposure in accordance with the R60 fire resistance requirement. The study was carried out in two successive stages. At the first stage, a fire analysis of the joint without fire protection was performed using the following initial parameters: the standard fire curve, convective heat transfer coefficient αc = 25 W/m²K, steel surface emissivity εm = 0.80, and fire environment emissivity εf = 1.00. The analysis showed intensive heating of the joint components to temperatures of approximately 935.86-942.88°C. However, after the introduction of contour fire protection with the following parameters: layer thickness dp = 30 mm, thermal conductivity λp = 0.2 W/(m•K), specific heat capacity cp = 1700 J/(kg•K), and density ρp = 800 kg/m³, the temperature decreased to the range of 221.43-380.97°C.
- 28 May 2026
- Published by Kyiv National University of Construction and Architecture in Building constructions. Theory and Practice
- No. 18
Open AccessAssessment of the fire resistance of a flanged joint of a steel truss
The article considers the specific features of the numerical assessment of the fire resistance of a spatial joint connecting tubular elements with a ring flange and radial stiffening ribs. The relevance of the study is due to the fact that, in steel structures under fire conditions, the limit state is often governed not by the overall strength of the main cross-section, but by the local behavior of joints, where a complex interaction occurs between the base metal, welds, bolts, contact zones, and stiffeners. It is precisely the joints that are the most sensitive to the reduction in the physical and mechanical properties of the material when heated, since stresses are concentrated in them, the force transfer pattern changes, and local failure mechanisms manifest themselves more rapidly. The aim of the study is to determine the influence of the fire-protective layer on the temperature regime and load-bearing capacity of the investigated joint under standard fire exposure in accordance with the R60 fire resistance requirement. The study was carried out in two successive stages. At the first stage, a fire analysis of the joint without fire protection was performed using the following initial parameters: the standard fire curve, convective heat transfer coefficient αc = 25 W/m²K, steel surface emissivity εm = 0.80, and fire environment emissivity εf = 1.00. The analysis showed intensive heating of the joint components to temperatures of approximately 935.86-942.88°C. However, after the introduction of contour fire protection with the following parameters: layer thickness dp = 30 mm, thermal conductivity λp = 0.2 W/(m•K), specific heat capacity cp = 1700 J/(kg•K), and density ρp = 800 kg/m³, the temperature decreased to the range of 221.43-380.97°C.
- Open Access
- 27 June 2025
- Published by Kyiv National University of Construction and Architecture in Building constructions. Theory and Practice
- No. 16,p. 56-65
Numerical investing of truss flange joints with trimmed flanges
In modern construction, steel trusses remain one of the most common types of load-bearing structures used in the construction of industrial, civil, and public buildings. Their use is driven by high load-carrying capacity, relatively easy installation, and economic feasibility in long-span structures.One of the most critical elements of such structures is the flange joint, through which the main internal forces are transferred from one part of the truss to another. The reliability and durability of the entire system largely depend on the accuracy of its calculation and design.Special attention must be paid to situations where the joint is subjected not only to axial loads but also to bending moments and torsion, which create a complex stress–strain state. In such cases, traditional calculation methods, based on simplified models and assumptions of uniform stress distribution, do not always allow for the identification of local concentrations that may lead to premature structural failure. In this context, improving numerical analysis methods that consider the real spatial geometry of the elements, the specifics of the connections, and the nature of the loading becomes especially relevant.The proposed approach is based on constructing an analytical model of the joint, enabling the calculation of internal forces in critical zones without the need to model the entire truss. This not only reduces the time required for calculations but also improves their accuracy. Such an approach contributes to the early detection of potentially hazardous zones where stress levels may exceed permissible limits, thereby reducing the risk of loss of serviceability.
- 27 June 2025
- Published by Kyiv National University of Construction and Architecture in Building constructions. Theory and Practice
- No. 16,p. 56-65
Open AccessNumerical investing of truss flange joints with trimmed flanges
In modern construction, steel trusses remain one of the most common types of load-bearing structures used in the construction of industrial, civil, and public buildings. Their use is driven by high load-carrying capacity, relatively easy installation, and economic feasibility in long-span structures.One of the most critical elements of such structures is the flange joint, through which the main internal forces are transferred from one part of the truss to another. The reliability and durability of the entire system largely depend on the accuracy of its calculation and design.Special attention must be paid to situations where the joint is subjected not only to axial loads but also to bending moments and torsion, which create a complex stress–strain state. In such cases, traditional calculation methods, based on simplified models and assumptions of uniform stress distribution, do not always allow for the identification of local concentrations that may lead to premature structural failure. In this context, improving numerical analysis methods that consider the real spatial geometry of the elements, the specifics of the connections, and the nature of the loading becomes especially relevant.The proposed approach is based on constructing an analytical model of the joint, enabling the calculation of internal forces in critical zones without the need to model the entire truss. This not only reduces the time required for calculations but also improves their accuracy. Such an approach contributes to the early detection of potentially hazardous zones where stress levels may exceed permissible limits, thereby reducing the risk of loss of serviceability.
- Open Access
- 29 November 2021
- Published by Kyiv National University of Construction and Architecture in Building constructions. Theory and Practice
- No. 8,p. 25-31
Modeling of physical wear assessment of zinc coating of space steel frame road structures for road safety information systems
The article developed an improved physical and mathematical model of the corrosive wear of zinc coating of steel structures in a city. The research is based on full-scale experimental data for determining the wear of a zinc coating of full-scale metal spatial structures of frame road structures for informational safety systems on roads after 10 years of operation in the conditions of Kyiv. The frame structure consists of metal columns and a steel crossbar frame. The crossbar frame is a spatial block of two steel trusses. The block of trusses is assembled from unified spatial sections united by vertical and horizontal ties, and which are connected by flange nodes of a special design. All structural elements are made of rolled tubes. Based on the research results, an approach to assessing the physical wear of the zinc coating of the spatial structural system is proposed. According to the peculiarities of the arrangement of elements in frame structures, and, accordingly, to different conditions and operations, an approach is proposed to assess the corrosive wear of a zinc coating for various groups of elements: columns, spatial block of two steel trusses, flange nodes. The physical and mathematical model is based on the working hypothesis of uneven wear of the zinc coating over time. It was found that for each group of structural elements, the conditions of the gaseous environment, the effects of atmospheric precipitation, wind speed, temperature changes individually affect the reduction of the zinc coating. The obtained experimental data were used to determine the parameter of the rate of decrease in the zinc coating of the physical and mathematical model. The results of the research and the development of the methodology helped to establish the operating conditions of the zinc coating according to the criterion of the rate of wear of the zinc coating, to classify the category of aggressiveness of the environment for each group of structural elements. Also, studies allow predicting the service life by reducing the thickness of the zinc coating, as well as the wear of the zinc coating in time in the subsequent period of operation. The methodology is universal and can be extended to other types of galvanized metal structures.
- 29 November 2021
- Published by Kyiv National University of Construction and Architecture in Building constructions. Theory and Practice
- No. 8,p. 25-31
Open AccessModeling of physical wear assessment of zinc coating of space steel frame road structures for road safety information systems
The article developed an improved physical and mathematical model of the corrosive wear of zinc coating of steel structures in a city. The research is based on full-scale experimental data for determining the wear of a zinc coating of full-scale metal spatial structures of frame road structures for informational safety systems on roads after 10 years of operation in the conditions of Kyiv. The frame structure consists of metal columns and a steel crossbar frame. The crossbar frame is a spatial block of two steel trusses. The block of trusses is assembled from unified spatial sections united by vertical and horizontal ties, and which are connected by flange nodes of a special design. All structural elements are made of rolled tubes. Based on the research results, an approach to assessing the physical wear of the zinc coating of the spatial structural system is proposed. According to the peculiarities of the arrangement of elements in frame structures, and, accordingly, to different conditions and operations, an approach is proposed to assess the corrosive wear of a zinc coating for various groups of elements: columns, spatial block of two steel trusses, flange nodes. The physical and mathematical model is based on the working hypothesis of uneven wear of the zinc coating over time. It was found that for each group of structural elements, the conditions of the gaseous environment, the effects of atmospheric precipitation, wind speed, temperature changes individually affect the reduction of the zinc coating. The obtained experimental data were used to determine the parameter of the rate of decrease in the zinc coating of the physical and mathematical model. The results of the research and the development of the methodology helped to establish the operating conditions of the zinc coating according to the criterion of the rate of wear of the zinc coating, to classify the category of aggressiveness of the environment for each group of structural elements. Also, studies allow predicting the service life by reducing the thickness of the zinc coating, as well as the wear of the zinc coating in time in the subsequent period of operation. The methodology is universal and can be extended to other types of galvanized metal structures.