FZFatih Zungor

Fatih Zungor

*This is an algorithmically generated author record based on publicly available information.

Fatih Zungor has a total of 11 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Enhanced Design of Single‐Switch Quasi‐Resonant Inverters for Induction Heating

    by Onur Gonullu, Seref Can Seyrek, Metin Ozturk, Fırat Kacar, Fatih Zungor, Durmus Ersoy

    Induction heating (IH) systems are widely adopted in household appliances thanks to their energy efficiency and inherently safe operation. To maximize performance, resonant inverter circuits are frequently employed in IH applications due to their capability for soft‐switching and high efficiency. Among the various resonant inverter topologies, the single‐switch quasi‐resonant (SSQR) inverter stands out as a cost‐effective solution, particularly in systems with lower power requirements. However, this topology has a relatively limited soft‐switching range, and its stability can be affected by variations in the electrical characteristics of the load and the resonant circuit components. For optimal design and reliable performance, it is essential to precisely determine the values of the resonant capacitor and the induction coil, which are central components of SSQR‐based IH cookers. These parameters significantly influence the interaction between load behavior, resonant circuit characteristics, and safe operation boundaries. Moreover, in systems with closed‐loop control for power regulation and safety management, careful selection of resonant elements is fundamental to achieving both efficiency and reliability. This study introduces a refined design approach for SSQR inverters used in residential IH devices. The method's effectiveness is analyzed theoretically and validated through both simulations and prototype testing.


  • Open Access

    Design Methodology of Series Resonant Half Bridge Inverter for Induction Cooker

    by Fatih Zungor, Haci Bodur, Metin Ozturk, Hulya Obdan

    Induction heating is a commonly used method of heating in household appliances due to its efficiency and high reliability reasons. In induction cookers, resonant inverter circuits are frequently chosen due to their high efficiency and the ability to facilitate soft switching. Among the resonant inverters used in induction cookers, half-bridge series resonant (HBSR) inverter topology is often preferred for applications where a balance between cost and power is required. Despite the numerous circuit designs proposed to enhance the performance of HBSR converters, a standardized design methodology suitable for circuit design dedicated to induction cookers has not yet been established. In this study, a new HBSR inverter design methodology supported by various theoretical equations is proposed for use in household induction cooktops. In the proposed design, the first step involves calculating the equivalent resistance value of the coil. Subsequently, a coil capable of achieving to match this resistance value is designed mechanically. Finally, the capacitance value for the resonance circuit is calculated. Calculating the equivalent resistance value before designing the coil, in particular, enables the practical implementation of a viable coil design. To validate the proposed design methodology, it is necessary to control the power transferred to the resonant circuit. For this purpose, closed-loop power control is achieved using the peak value of coil current through frequency modulation technique. Additionally, it needs to be also proved that the implementation circuit works with soft switching between maximum and minimum switch cut-off current. To assess the compliance of the proposed design method with standards, thermal measurements were taken from semiconductors, EMC measurements were conducted to verify compliance with the IEC 55014-1 standard, and finally, the power transferred to the resonant circuit was calculated using oscilloscope measurements. Using the proposed design method, calculations were performed for a 20cm diameter iron pot with a 2300VA power transfer at 230VAC mains voltage. Subsequently, these calculations were verified using various simulation tools, and finally, a prototype implementation circuit was realized to demonstrate the reliability of the proposed design method.


  • Implementation of Forward Converter with Active Clamp for Welding Machines

    by Fatih Zungor, M. Faruk Bilicioglu, Enes Kavak, Ibrahim Eski, Metin Ozturk, Haci Bodur

    Among the converters used in welding machines, two-switch forward converter has an important place in low and medium power applications for cost priority applications. However, one of the most important disadvantage of this converter is limited duty cycle, which is less than 50%. Therefore, the capacitors used for shaping the main line voltage occupy an important place on the circuit. Another disadvantage of the converter is that the transformer uses the B-H curve unidirectional way. This causes the transformer to be selected larger when compared to other converters for the same power value. In this study, it has been suggested use forward converter with active clamp to which provides using the B-H curve bidirectional way with clamp capacitor, extending duty cycle more than %50 and increasing power density solve these disadvantages of two switch forward converter for welding machines. For this purpose, a converter with 230V input; 25V/150A and 3750W output will be designed and simulated to show that the converter solves the mentioned disadvantages.