Pablo González
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Pablo González has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Carlos Alcaide
TEAM, Universitat Politcnica de Valncia, Valencia, Spain
3 shared publications - Jose Vicente Morro
TEAM, Universitat Politcnica de Valncia, Valencia, Spain
3 shared publications - Pablo Soto
TEAM, Universitat Politcnica de Valncia, Valencia, Spain
3 shared publications - Ana Rodriguez
Departamento de Comunicaciones-iTEAM, Universitat Politècnica de València, Valencia, Spain
2 shared publications - Miguel Rodríguez Jodar
ESA-VSC European High Power RF Space Laboratory, Valencia, Spain
2 shared publications - Raúl Cervera-Marín
TEAM, Universitat Politcnica de Valncia, Valncia, Spain
2 shared publications
Latest Publications
- Open Access
- 26 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 5 (2) , 438-450
Multipactor Breakdown Threshold Estimation Based on Circuital Models and Particle Simulations for Multicarrier Signals in RF Filters
Multipactor is a harmful effect that may challenge the correct operation of satellite communication systems by limiting the system power-handling capability, and hence its overall performance. Therefore, the development of techniques for predicting the multipactor threshold is of great practical interest. For narrowband components, rough estimations can be obtained from experimental charts, normally resulting in conservative thresholds. More accurate predictions can be obtained with particle simulators, at the expense of a much higher computational effort. This study proposes an approach based on circuital models for swift and accurate multipactor threshold predictions, specifically addressing short-term discharges induced by multicarrier signals in narrowband samples. The use of reduced, but representative, electromagnetic (EM) models of the critical gap region is discussed in detail. Through the use of these models, it is possible to avoid simulating the complete structure, increasing the computational efficiency and enabling the fulfillment of the power requirements at early design stages. The proposed technique is validated through commercial particle simulators, showcasing its efficacy, efficiency, and key benefits.
- 26 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 5 (2) , 438-450
Open AccessMultipactor Breakdown Threshold Estimation Based on Circuital Models and Particle Simulations for Multicarrier Signals in RF Filters
Multipactor is a harmful effect that may challenge the correct operation of satellite communication systems by limiting the system power-handling capability, and hence its overall performance. Therefore, the development of techniques for predicting the multipactor threshold is of great practical interest. For narrowband components, rough estimations can be obtained from experimental charts, normally resulting in conservative thresholds. More accurate predictions can be obtained with particle simulators, at the expense of a much higher computational effort. This study proposes an approach based on circuital models for swift and accurate multipactor threshold predictions, specifically addressing short-term discharges induced by multicarrier signals in narrowband samples. The use of reduced, but representative, electromagnetic (EM) models of the critical gap region is discussed in detail. Through the use of these models, it is possible to avoid simulating the complete structure, increasing the computational efficiency and enabling the fulfillment of the power requirements at early design stages. The proposed technique is validated through commercial particle simulators, showcasing its efficacy, efficiency, and key benefits.
- 1 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 33 (6) , 675-678
A New Reference Sample for High-Frequency Multipactor Testing
Multipactor (MP) is a high-power effect severely limiting the performance of satellite communication links. A reference sample is normally used in the experimental setups for MP testing in order to verify its correct operation. However, the low gaps required for high frequencies jeopardize the manufacturability of the devices traditionally used for this purpose. A new reference sample, based on a stepped-impedance resonator (SIR), is proposed in this letter. The key design considerations are also outlined. A prototype operating between 17 and 18 GHz has been manufactured and tested, proving the novel structure allows higher gaps, and is, thus, suitable for higher frequency bands.
- 1 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 33 (6) , 675-678
A New Reference Sample for High-Frequency Multipactor Testing
Multipactor (MP) is a high-power effect severely limiting the performance of satellite communication links. A reference sample is normally used in the experimental setups for MP testing in order to verify its correct operation. However, the low gaps required for high frequencies jeopardize the manufacturability of the devices traditionally used for this purpose. A new reference sample, based on a stepped-impedance resonator (SIR), is proposed in this letter. The key design considerations are also outlined. A prototype operating between 17 and 18 GHz has been manufactured and tested, proving the novel structure allows higher gaps, and is, thus, suitable for higher frequency bands.
- Open Access
- 23 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 2 (1) , 57-77
Multipactor Threshold Estimation Techniques Based on Circuit Models, Electromagnetic Fields, and Particle Simulators
Multipactor has become a keylimiting factor of the final performance of satellite communication systems, due to the increase in power levels and/or operating frequency bands. As a result, the critical components of these systems must meet demanding multipactor specifications which should be considered during the design process. This paper describes the different techniques available to predict the multipactor threshold power for radio frequency (RF) and microwave passive hardware under continuous wave (CW) excitation, from cumbersome particle simulations to fast approximate methods based on circuit models. All these techniques have been described and compared together for the first time, including also a detailed description of the configuration issues of commercial particle simulators required to obtain accurate multipactor threshold predictions. The techniques are applied to both wideband and narrowband application examples. The predictions have been compared with measured thresholds of manufactured samples obtained with a novel multipactor test bed, thus allowing to highlight the advantages and limitations of each technique and particle simulator. From this paper, it will be possible to choose the most suitable procedure (and an appropriate simulator, if needed) to obtain multipactor threshold prediction of passive hardware.
- 23 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 2 (1) , 57-77
Open AccessMultipactor Threshold Estimation Techniques Based on Circuit Models, Electromagnetic Fields, and Particle Simulators
Multipactor has become a keylimiting factor of the final performance of satellite communication systems, due to the increase in power levels and/or operating frequency bands. As a result, the critical components of these systems must meet demanding multipactor specifications which should be considered during the design process. This paper describes the different techniques available to predict the multipactor threshold power for radio frequency (RF) and microwave passive hardware under continuous wave (CW) excitation, from cumbersome particle simulations to fast approximate methods based on circuit models. All these techniques have been described and compared together for the first time, including also a detailed description of the configuration issues of commercial particle simulators required to obtain accurate multipactor threshold predictions. The techniques are applied to both wideband and narrowband application examples. The predictions have been compared with measured thresholds of manufactured samples obtained with a novel multipactor test bed, thus allowing to highlight the advantages and limitations of each technique and particle simulator. From this paper, it will be possible to choose the most suitable procedure (and an appropriate simulator, if needed) to obtain multipactor threshold prediction of passive hardware.