CACeyda Akın

Ceyda Akın

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Ceyda Akın has a total of 9 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Effect of Surface Treatments on the Repair Bond Strength Between Aged Glass Ceramics and Composite Resin: An In Vitro Study

    by Melika Ahmad, Bilgehan Kottaş, Abdulhaluk Savaş, Tuba Yılmaz Savaş, Ceyda Akın

    Background: This study aimed to investigate the effects of glass bead particle abrasion and different primer systems on the repair bond strength of two types of aged glass ceramics and composite resins. Methods: Eighty specimens were prepared from leucite-reinforced (G-Ceram) and lithium disilicate (IPS e.max CAD) glass-ceramic materials. After thermocycling (5–55 °C, 30 s dwell time, 5000 cycles), each ceramic specimen was divided into five test groups (n=8): control (C), air abrasion with 50-µm glass beads (GB), 37% phosphoric acid etching, Clearfil Ceramic Primer Plus application (CP), Monobond Etch&Prime (MEP) application, 4.8% hydrofluoric acid etching, and Monobond N (MN) application. All specimens were coated with a universal adhesive (Nova Compo B Plus) following treatment. Clearfil Majesty Esthetic, a nanohybrid composite resin, was applied. The specimens were kept in distilled water at 37 °C for 24 h and evaluated for the shear bond strength (1 mm/min). Data were statistically analyzed using two-way ANOVA, Tukey HSD and Bonferroni post-hoc tests (α=0.05).Results: Surface treatment and its interaction with the ceramic material exhibited a statistically significant effect on the repair bond strength (P < 0.05), whereas the main effect of the ceramic type was not significant (P > 0.05). The C and GB groups demonstrated significantly lower mean bond strength values than the CP, MEP, and MN groups (P < 0.05). For the lithium disilicate ceramics, both the CP and MN groups produced the highest bond strengths, with no significant difference between them (P > 0.05). In the leucite-reinforced ceramics, the MN group showed significantly higher bond strength than the CP (P < 0.05). Although the overall effect of surface treatment was consistent across ceramic types, in the CP group, lithium disilicate specimens exhibited a higher bond strength than leucite-reinforced ceramics (P < 0.05).Conclusions: Both phosphoric acid and hydrofluoric acid etching followed by different primer applications achieved the highest bond strength for lithium disilicate ceramics, whereas silane-based treatment after hydrofluoric acid etching was the most effective for leucite-reinforced ceramics. Overall, the tested primers significantly enhanced the bonding to aged glass-ceramics, supporting their use in repair procedures.

  • Open Access

    Influence of margin level and finish line geometry on the trueness of digital scans

    by Mehmet Gözen, Ceyda Akın

    Gözen M, et al. J Adv Prosthodont. 2026 Aug;18(4):362-373. https://doi.org/10.4047/jap.2026.18.4.362

  • The Effects of Different Restoration Materials on the Trueness of Intraoral Scanners

    by Mehmet Gözen, Neslihan Günteki̇n, Ceyda Akin

    Aim: This study aimed to assess how different restoration materials affect the trueness of intraoral scanners. Materials and Methods: Artificial teeth on a typodont model were prepared for crowns and fixed partial dentures (FPDs) using full metal, monolithic zirconia, and porcelain-fused-to-metal (PFM) materials. Each group underwent 10 scans with a Trios intraoral scanner, generating 60 STL files. A reference scanner created a master model using scanning spray to reduce reflection errors. The STL files were aligned with reverse engineering software for comparison and were analyzed in micrometers (μm) using Root Mean Square (RMS) and Mean Distance measurements. The Levene test and two-way ANOVA with Post Hoc analysis were used for statistical evaluation. Results: The RMS deviations for the FPDs were 77.9 ± 15.2 μm (full metal), 84.6 ± 6.9 μm (monolithic zirconia), and 130 ± 19.7 μm (PFM). For the crowns, the RMS values were 76.9 ± 6.5 μm (metal), 71 ± 8.2 μm (monolithic zirconia), and 153 ± 22.4 μm (PFM). The mean distance deviations for the FPDs were 11.4 ± 4.8 μm (metal), 11.2 ± 3.4 μm (monolithic zirconia), and 18.3 ± 2.6 μm (PFM). For the crowns, the mean distances were 8.6 ± 3.4 μm (metal), 10.2 ± 3 μm (monolithic zirconia), and 24.7 ± 3.3 μm (PFM). Significant differences were noted in the PFM groups. Conclusion: Restoration materials notably affected intraoral scanner trueness, especially PFM restorations. The restoration length did not significantly affect the accuracy.

  • Open Access

    Investigation of the effect of different experimental acid solutions applied on the zirconia surface on the bond strength between zirconia and resin cement: A pilot study

    by Tuba Yılmaz Savaş, Abdulhaluk Savaş, Ceyda Akın, Ali Rıza Tunçdemir

    Aim: The purpose of this study is to examine the effects of two different experimental acid solutions and sandblasting on the bond strength between zirconia ceramic core material and resin cement. Methodology: Forty zirconia core materials were prepared and separated into four groups based on the surface treatment to be applied (n = 10) as follows: 1) Control Group: no surface treatment was performed; 2) Sandblasting Group: the specimen surfaces were sandblasted with 50 µm aluminum oxide particles from a distance of 10 mm at 3 bar pressure for 15 seconds; 3) Sol-1 Group: H2O:HF:H2O2 solution was applied for 60 seconds, washed, and then dried; and 4) Sol-2 Group: H2O:HF:HNO3 solution was applied to the surfaces of the specimens for 60 seconds, washed, and then dried. All specimens were coated with a dual-cure resin cement with a 2.8-mm diameter. After 24 hours, the specimens were tested for shear bond strength (SBS) at 1 mm/min using a universal testing device. Statistical analysis was conducted using one-way analysis of variance (ANOVA) and Tukey HSD tests with a confidence interval of 95%. Results: The difference among the groups was statistically significant (p = 0.002) based on the one-way ANOVA results. The Control Group had the lowest SBS (8.06 ± 4.52), whereas the Sol-1 Group had the highest SBS (17.10 ± 5.67). The Sol-1 and Sol-2 Groups demonstrated comparable bonding strength values (p = 0.17). The Sandblasting and Sol-1 Groups exhibited considerably stronger bond strength than the Control Group (p = 0.05). Conclusion: The experimental acid solutions enhanced the bond strength between the resin cement and the zirconia ceramic at the sandblasting treatment level. How to cite this article: Yılmaz Savaş T, Savaş A, Akın C, Tunçdemir AR. Investigation of the effect of different experimental acid solutions applied on the zirconia surface on the bond strength between zirconia and resin cement: A pilot study. Int Dent Res 2022;12(Suppl.1):69-73. https://doi.org/10.5577/intdentres.458 Linguistic Revision: The English in this manuscript has been checked by at least two professional editors, both native speakers of English.

  • Farklı Seramik Primerleri ve Kumlamanın Rezin Siman ile Zirkonya Arasındaki Bağlanma Dayanımına Etkisi

    by Tuba Yilmaz Savaş, Si̇mEl Karaca, Ceyda Akin, Özgür İnAn

    Amaç: Bu çalışmanın amacı, farklı primerler ve kumlamanın self-adeziv rezin siman ile zirkonya materyali arasındaki makaslama bağlanma dayanımı üzerindeki etkisini araştırmaktır. Gereç ve Yöntemler: Elli adet zirkonya örneği hazırlandı ve sinterlendi. Örnekler uygulanan yüzey işlemine göre rastgele 5 farklı gruba ayrıldı (n=10): Grup N (kontrol; ek yüzey işlemi uygulanmadı), Grup K (örnekler 50 µm Al2 O3 partikülleri ile kumlandı), Grup S (örneklere Super-Bond Universal Ceramic Primer uygulandı), Grup M (örneklere Monobond N uygulandı) ve Grup Z (örneklere Z-Prime Plus uygulandı). Daha sonra tüm örneklere 3 mm çapında self-adeziv rezin siman uygulandı. Örnekler, üniversal bir test makinesinde 1 mm/dk'lık hız altında makaslama bağlanma dayanımı testine tabi tutuldu. İstatistiksel analizler tek yönlü ANOVA ve Tukey HSD testleri ile %95 güven aralığında yapıldı. Bulgular: Grupların ortalama bağlanma dayanımı değerleri arasında anlamlı fark bulundu (P<0.001). Grup K, Grup N'den önemli ölçüde daha yüksek bir ortalama bağlanma dayanımı değeri gösterdi (P<0.05); ancak primer gruplarından önemli derecede daha düşük ortalama bağlanma dayanımı değeri gösterdi (P<0.05). Grup S, M ve Z; Grup N ve Grup K'dan istatistiksel olarak daha yüksek ortalama bağlanma dayanımı değerleri gösterdi (P0.05). Sonuç: Primer yöntemi, kumlama işlemine kıyasla rezin siman ve zirkonya arasındaki bağlanma dayanımını önemli derecede iyileştirmiştir. Farklı primerler, karşılaştırılabilir makaslama bağlanma dayanımı sonuçları göstermiştir.

  • Effect of Non-Thermal Plasma Treatment on Shear Bond Strength Between Monolithic Zirconia and Resin Cement

    by Tuba Yilmaz Savaş, Ceyda Akin

    Amaç: Bu çalışmanın amacı, farklı plazma tipleri (argon ve oksijen), primer ve kumlama uygulamalarının monolitik zirkonya ile self-adeziv rezin siman arasındaki makaslama bağlanma dayanımına etkisinin incelenmesidir. Gereç ve Yöntemler: Elli adet monolitik zirkonya disk hazırlandı ve sinterlendi. Zirkonya diskler uygulanacak yüzey işlemine göre rastgele beş gruba ayrıldı: Kontrol (herhangi bir yüzey işlemi uygulanmadı), Kumlama (50 μm Al2O3 ile kumlama), Primer (universal seramik primer uygulaması), Oksjen Plazma (10 dakika oksijen plazma uygulaması) ve Argon Plazma (10 dakika argon plazma uygulaması). Örneklere dual-cure bir rezin siman uygulandı ve örneklere 5500 devir termal siklus işlemi yapıldı. Makaslama bağlanma dayanımı testi 1 mm/dak hızında universal bir test cihazında gerçekleştirildi. Veriler tek yönlü ANOVA ve Tukey HSD post-hoc testleri kullanılarak 0.05 anlamlılık düzeyinde analiz edildi. Bulgular: Gruplar arasındaki ortalama makaslama bağlanma dayanımı değerleri arasında istatistiksel olarak anlamlı fark bulundu (P0.05). Oksijen ve Argon Plazma grupları Kontrol grubuna göre daha yüksek ancak Kumlama ve Primer gruplarına kıyasla daha düşük bağlanma dayanımı değerleri gösterdi (P0.05). Sonuç: Plazma uygulaması rezin ile zirkonya arasındaki bağlantıyı arttırmıştır ancak bu artış kumlama ve primer uygulamaları seviyesinde olmamıştır. Primer ve kumlama uygulamaları birbirine alternatif yöntemler olarak kullanılabilir.

  • Effect of nonthermal plasma treatment on surface roughness and bond strength between veneer ceramic and zirconia core

    by Tuba Yılmaz Savaş, Ceyda Akın

    This in vitro study evaluated the effect of nonthermal plasma (NTP) treatment on the surface roughness (Ra) of the zirconia and the shear bond strength (SBS) between the veneer ceramic and the zirconia. Ninety zirconia specimens were divided into six groups according to the surface treatments applied: control with no treatment; sandblasting with 50‐μm Al 2 O 3 particles; oxygen plasma treated for 5 min; oxygen plasma treated for 10 min; argon plasma treated for 5 min; and argon plasma treated for 10 min. Ra values were measured using a profilometer. Specimens ( n  = 12) were then veneered with a nano‐fluorapatite ceramic, and the SBS test was performed. Scanning electron microscopy, atomic force microscopy, and X‐ray diffraction analyses were performed. The sandblasting procedure significantly increased the surface roughness; however, the plasma groups showed similar Ra values compared to the control group. NTP and sandblasting treatment significantly increased the bond strength and led to higher SBS values than the control. Plasma application did not induce phase transformation; however, sandblasting caused monoclinic phase transformation of the zirconia. NTP application (either oxygen or argon) can enhance the bond strength between the veneer ceramic and the zirconia core without altering the surface morphology or causing zirconia phase transformation.