Flora Somidin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Flora Somidin has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Hiroshi Maeno
The Ultramicroscopy Research Center, Kyushu University, Fukuoka 819-0395, Japan
3 shared publications - Kazuhiro Nogita
Nihon Superior Centre for the Manufacture of Electronic Materials (NS CMEM), School of Mechanical and Mining Engineering, The University of Queensland, St. Lucia, QLD 4072, Australia
3 shared publications - Stuart D. McDonald
School of Mechanical and Mining Engineering, The University of Queensland, St Lucia, QLD 4072, Australia
3 shared publications - Xin Fu Tan
Nihon Superior Centre for the Manufacture of Electronic Materials (NS CMEM), School of Mechanical and Mining Engineering, The University of Queensland, St. Lucia, QLD 4072, Australia
3 shared publications - Christopher M. Gourlay
Department of Materials, Imperial College London, London, UK
2 shared publications - Guang Zeng
School of Materials Science and Engineering, Central South University, Changsha, China
2 shared publications
Latest Publications
- Open Access
- 21 November 2025
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 36 (33) , 2117
Effect of indium on microstructure, phase stability, anisotropic lattice behavior and mechanical performance of Sn-58Bi solder alloy
- 21 November 2025
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 36 (33) , 2117
Open AccessEffect of indium on microstructure, phase stability, anisotropic lattice behavior and mechanical performance of Sn-58Bi solder alloy
- Open Access
In Situ Observation of Deformation in a Sn-3Ag-0.5Cu/Cu Solder Joint Using High-Voltage Transmission Electron Microscopy
For reliable electronics, it is important to have an understanding of solder joint failure mechanisms. However, because of difficulties in real-time atomistic scale analysis during deformation, we still do not fully understand these mechanisms. Here, we report on the development of an innovative in situ method of observing the response of the microstructure to tensile strain at room temperature using high-voltage transmission electron microscopy (HV-TEM). This technique was used to observe events including dislocation formation and movement, grain boundary formation and separation, and crack initiation and propagation in a Sn-3 wt.%Ag-0.5 wt.%Cu (SAC305) alloy joint formed between copper substrates.
Open AccessIn Situ Observation of Deformation in a Sn-3Ag-0.5Cu/Cu Solder Joint Using High-Voltage Transmission Electron Microscopy
For reliable electronics, it is important to have an understanding of solder joint failure mechanisms. However, because of difficulties in real-time atomistic scale analysis during deformation, we still do not fully understand these mechanisms. Here, we report on the development of an innovative in situ method of observing the response of the microstructure to tensile strain at room temperature using high-voltage transmission electron microscopy (HV-TEM). This technique was used to observe events including dislocation formation and movement, grain boundary formation and separation, and crack initiation and propagation in a Sn-3 wt.%Ag-0.5 wt.%Cu (SAC305) alloy joint formed between copper substrates.
- Open Access
- 8 July 2025
- Published by MDPI AG in Preprints.org
Dynamic Recrystallisation and Crack Propagation in a Sn-3Ag-0.5Cu/Cu Solder Joint
If electronics manufacturers and users are to have confidence in the reliability of the solder joints on which they rely, it is essential to have an understanding of the solder joint failure mechanisms and the role of dynamic recrystallisation in failure. However, due to difficulties in real-time atomistic scale analysis during deformation, we still do not fully understand these mechanisms. Here, we report the development of an innovative in-situ method using high voltage transmission electron microscopy (HV-TEM) for observation of the microstructural response of a solder joint to room temperature tensile loading. This technique was used to observe events including dislocation formation, dynamic recrystallisation, grain boundary separation, and crack formation and propagation in a Sn-3wt.%Ag-0.5wt.%Cu (SAC305) alloy joint formed between copper substrates.
- 8 July 2025
- Published by MDPI AG in Preprints.org
Open AccessDynamic Recrystallisation and Crack Propagation in a Sn-3Ag-0.5Cu/Cu Solder Joint
If electronics manufacturers and users are to have confidence in the reliability of the solder joints on which they rely, it is essential to have an understanding of the solder joint failure mechanisms and the role of dynamic recrystallisation in failure. However, due to difficulties in real-time atomistic scale analysis during deformation, we still do not fully understand these mechanisms. Here, we report the development of an innovative in-situ method using high voltage transmission electron microscopy (HV-TEM) for observation of the microstructural response of a solder joint to room temperature tensile loading. This technique was used to observe events including dislocation formation, dynamic recrystallisation, grain boundary separation, and crack formation and propagation in a Sn-3wt.%Ag-0.5wt.%Cu (SAC305) alloy joint formed between copper substrates.
- Open Access
- 27 December 2024
- Published by Penerbit Universiti Malaysia Perlis in International Journal of Nanoelectronics and Materials (IJNeaM)
- Vol. 17 (December) , 341-346
Effect of Multiple Reflow Cycles and Isothermal Aging on Shear Strength in SAC305/Sn58Bi/Cu-OSP Hybrid Solder Joint
This study investigates the effects of multiple reflow cycles and isothermal aging on the shear strength and microstructure of SAC305/Sn58Bi/Cu-OSP hybrid solder joints. The joints combine SAC305 solder spheres and Sn58Bi solder paste reflowed on Cu-OSP substrates. Microstructural analysis revealed two distinct regions: a Bi-rich phase at the bottom and an Ag-rich phase at the top. Reflow cycles and isothermal aging at 85 °C, 125 °C, and 150 °C for up to 120 hours were evaluated for their impact on mechanical performance and reliability. Shear tests at 100 mm/s and 2000 mm/s showed that hybrid joints outperformed conventional SAC305/Cu-OSP joints, even after multiple reflow cycles. Aging at 85 °C and 125 °C had minimal impact on shear strength, indicating good stability under moderate conditions. However, aging at 150 °C, above the melting point of Sn58Bi (138 °C), caused a significant decrease in strength. These findings highlight the potential of hybrid solder joints for improved mechanical performance and thermal stability, offering advantages over conventional solder joints for advanced electronic packaging.
- 27 December 2024
- Published by Penerbit Universiti Malaysia Perlis in International Journal of Nanoelectronics and Materials (IJNeaM)
- Vol. 17 (December) , 341-346
Open AccessEffect of Multiple Reflow Cycles and Isothermal Aging on Shear Strength in SAC305/Sn58Bi/Cu-OSP Hybrid Solder Joint
This study investigates the effects of multiple reflow cycles and isothermal aging on the shear strength and microstructure of SAC305/Sn58Bi/Cu-OSP hybrid solder joints. The joints combine SAC305 solder spheres and Sn58Bi solder paste reflowed on Cu-OSP substrates. Microstructural analysis revealed two distinct regions: a Bi-rich phase at the bottom and an Ag-rich phase at the top. Reflow cycles and isothermal aging at 85 °C, 125 °C, and 150 °C for up to 120 hours were evaluated for their impact on mechanical performance and reliability. Shear tests at 100 mm/s and 2000 mm/s showed that hybrid joints outperformed conventional SAC305/Cu-OSP joints, even after multiple reflow cycles. Aging at 85 °C and 125 °C had minimal impact on shear strength, indicating good stability under moderate conditions. However, aging at 150 °C, above the melting point of Sn58Bi (138 °C), caused a significant decrease in strength. These findings highlight the potential of hybrid solder joints for improved mechanical performance and thermal stability, offering advantages over conventional solder joints for advanced electronic packaging.
- Open Access
In Situ Observation of Liquid Solder Alloys and Solid Substrate Reactions Using High-Voltage Transmission Electron Microscopy
The complex reaction between liquid solder alloys and solid substrates has been studied ex-situ in a few studies, utilizing creative setups to “freeze” the reactions at different stages during the reflow soldering process. However, full understanding of the dynamics of the process is difficult due to the lack of direct observation at micro- and nano-meter resolutions. In this study, high voltage transmission electron microscopy (HV-TEM) is employed to observe the morphological changes that occur in Cu6Sn5 between a Sn-3.0 wt%Ag-0.5 wt%Cu (SAC305) solder alloy and a Cu substrate in situ at temperatures above the solidus of the alloy. This enables the continuous surveillance of rapid grain boundary movements of Cu6Sn5 during soldering and increases the fundamental understanding of reaction mechanisms in solder solid/liquid interfaces.
Open AccessIn Situ Observation of Liquid Solder Alloys and Solid Substrate Reactions Using High-Voltage Transmission Electron Microscopy
The complex reaction between liquid solder alloys and solid substrates has been studied ex-situ in a few studies, utilizing creative setups to “freeze” the reactions at different stages during the reflow soldering process. However, full understanding of the dynamics of the process is difficult due to the lack of direct observation at micro- and nano-meter resolutions. In this study, high voltage transmission electron microscopy (HV-TEM) is employed to observe the morphological changes that occur in Cu6Sn5 between a Sn-3.0 wt%Ag-0.5 wt%Cu (SAC305) solder alloy and a Cu substrate in situ at temperatures above the solidus of the alloy. This enables the continuous surveillance of rapid grain boundary movements of Cu6Sn5 during soldering and increases the fundamental understanding of reaction mechanisms in solder solid/liquid interfaces.
- 1 January 2022
- Published by Springer Nature
- p. 95-112
Recent Progress in Transient Liquid Phase (TLP) Solder for Next Generation Power Electronics
- 1 January 2022
- Published by Springer Nature
- p. 95-112
Recent Progress in Transient Liquid Phase (TLP) Solder for Next Generation Power Electronics