Hiroki Ishikuro
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Hiroki Ishikuro has a total of 87 co-authors. Here are the top co-authors by number of shared publications:
- Noriyuki Miura
Department of Electronics and Electrical Engineering, Keio University, Yokohama, Kanagawa, Japan
5 shared publications - Tadahiro Kuroda
Keio University
5 shared publications - Tadahiro Kuroda
Graduate School of Engineering, The University of Tokyo, Tokyo, Japan
5 shared publications - Yohsuke Shiiki
Department of Electronics and Electrical Engineering, Keio University, Yokohama, Japan
5 shared publications - Kaoru Yamashita
Department of Electronics and Electrical Engineering, Keio University, Yokohama, Japan
4 shared publications - Vadim Issakov
Institute for CMOS Design, TU Braunschweig, Brunswick, Germany
4 shared publications
Latest Publications
- Open Access
- 31 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 36 (6) , 890-893
A Cryo-CMOS Fractional-N PLL in 22 nm FDSOI Operating at 6 K for Trapped-Ion Quantum Computer Applications
This letter presents a fractional-N charge-pump phase-locked loop (CP-PLL) operating at cryogenic temperatures (CT) down to 6 K. The phase-locked loop (PLL), generating signals in the frequency range around 2.28–2.68 GHz, is intended as a reference source in a microwave signal generator for a trapped-ion quantum computer operating with ${}^{{9}}\text {Be}^{\text {+}}$ ions. Using a third-order MASH DSmodulator (DSM), the PLL achieves a highly competitive FoM of −245 dB. The circuit exhibits the highest fractional spur suppression among the recently reported cryogenic PLLs, as well as the lowest chip area.
- 31 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 36 (6) , 890-893
Open AccessA Cryo-CMOS Fractional-N PLL in 22 nm FDSOI Operating at 6 K for Trapped-Ion Quantum Computer Applications
This letter presents a fractional-N charge-pump phase-locked loop (CP-PLL) operating at cryogenic temperatures (CT) down to 6 K. The phase-locked loop (PLL), generating signals in the frequency range around 2.28–2.68 GHz, is intended as a reference source in a microwave signal generator for a trapped-ion quantum computer operating with ${}^{{9}}\text {Be}^{\text {+}}$ ions. Using a third-order MASH DSmodulator (DSM), the PLL achieves a highly competitive FoM of −245 dB. The circuit exhibits the highest fractional spur suppression among the recently reported cryogenic PLLs, as well as the lowest chip area.
- 17 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (3) , 977-989
A 4.2–373 K Functional 800-MS/s 12-b Buffer-Then-Amplify Charge-Pump-Based Pipelined TI-SAR ADC With Integrated Active-Hold Technique
This article presents a source-follower (SF) and charge-pump (CP)-based amplification that is linear and bias-calibration-free across a wide temperature range from 4.2 to 373 K, targeting pipelined analog-to-digital converters (ADCs). While prior SF and CP-based amplifiers suffer from poor linearity because the SF must drive large amplified signals, we propose a buffer-then-amplify (BTA) CP architecture that relocates the CP to the SF output. As a result, the SF only buffers unamplified small-swing residues, fully exploiting its intrinsic linearity and eliminating the need for high-order gain calibrations even in advanced process nodes. To further enhance robustness and efficiency, we introduce an adaptively biased class-AB SF. An integrated active-hold technique is also proposed to eliminate the timing and bandwidth mismatch between the first-pipeline-stage sampling capacitor and the sub-ADC by repurposing the SF as a hold buffer for the sub-ADC. The prototype 12-bit 800-MS/s pipelined time-interleaved successive approximation register (TI-SAR) ADC is fabricated in 12-nm FinFET technology. It achieves SNDR higher than 55.0 dB across the 4.2–373 K temperature range with 40-MHz input, and peak Walden figure-of-merit (FoMW) of 9.2 fJ/c.-step at 4.2 K. To the best of the authors’ knowledge, the achieved functional temperature range is the widest among >10-bit >300-MS/s ADCs.
- 17 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (3) , 977-989
A 4.2–373 K Functional 800-MS/s 12-b Buffer-Then-Amplify Charge-Pump-Based Pipelined TI-SAR ADC With Integrated Active-Hold Technique
This article presents a source-follower (SF) and charge-pump (CP)-based amplification that is linear and bias-calibration-free across a wide temperature range from 4.2 to 373 K, targeting pipelined analog-to-digital converters (ADCs). While prior SF and CP-based amplifiers suffer from poor linearity because the SF must drive large amplified signals, we propose a buffer-then-amplify (BTA) CP architecture that relocates the CP to the SF output. As a result, the SF only buffers unamplified small-swing residues, fully exploiting its intrinsic linearity and eliminating the need for high-order gain calibrations even in advanced process nodes. To further enhance robustness and efficiency, we introduce an adaptively biased class-AB SF. An integrated active-hold technique is also proposed to eliminate the timing and bandwidth mismatch between the first-pipeline-stage sampling capacitor and the sub-ADC by repurposing the SF as a hold buffer for the sub-ADC. The prototype 12-bit 800-MS/s pipelined time-interleaved successive approximation register (TI-SAR) ADC is fabricated in 12-nm FinFET technology. It achieves SNDR higher than 55.0 dB across the 4.2–373 K temperature range with 40-MHz input, and peak Walden figure-of-merit (FoMW) of 9.2 fJ/c.-step at 4.2 K. To the best of the authors’ knowledge, the achieved functional temperature range is the widest among >10-bit >300-MS/s ADCs.
- Open Access
- 2 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (2) , 673-689
A Cryo-BiCMOS Controller for Quantum Computers based on Trapped Beryllium Ions
This article presents a cryo-BiCMOS system on chip (SoC) designed for single and two-qubit gate operations for quantum computers (QCs) based on beryllium trapped-ions (TIs). Signal generation from 0.7 to 1.6 GHz is supported, covering all microwave transitions in a ${}^{9}\text {Be}^{+}$ QC realization. An integrated 48-kbit waveform memory is implemented for improved two-qubit gate fidelity. The fabricated IC is verified in a 4 K environment with up to 4 qubits, thus enabling quantum processor unit (QPU) cointegration. IC operation up to RT ensures compatibility with future system realizations. Measurements demonstrate qubit state control with an oscillation amplitude of 94% before SPAM correction and Rabi oscillation rate of 172 kHz. Evaluations of long sequences of $\sigma _{x}$ gates indicate control of the quantum state with high quality. Interaction with one computational zone is possible at a total power consumption of 86 mW translating to 21.5 mW/qubit in the presented measurements. Comparison with the state-of-the-art controller reveals drastic power and form-factor reduction at comparable performance, thus paving the way for a scalable TI platform. The chip is fabricated in a 0.13- $\mathrm {\mu }\mathrm {m}$ SiGe BiCMOS technology. To the best of our knowledge, this is the first reported from-scratch system design for TI-based QC concluding with a qubit state manipulation demonstration.
- 2 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (2) , 673-689
Open AccessA Cryo-BiCMOS Controller for Quantum Computers based on Trapped Beryllium Ions
This article presents a cryo-BiCMOS system on chip (SoC) designed for single and two-qubit gate operations for quantum computers (QCs) based on beryllium trapped-ions (TIs). Signal generation from 0.7 to 1.6 GHz is supported, covering all microwave transitions in a ${}^{9}\text {Be}^{+}$ QC realization. An integrated 48-kbit waveform memory is implemented for improved two-qubit gate fidelity. The fabricated IC is verified in a 4 K environment with up to 4 qubits, thus enabling quantum processor unit (QPU) cointegration. IC operation up to RT ensures compatibility with future system realizations. Measurements demonstrate qubit state control with an oscillation amplitude of 94% before SPAM correction and Rabi oscillation rate of 172 kHz. Evaluations of long sequences of $\sigma _{x}$ gates indicate control of the quantum state with high quality. Interaction with one computational zone is possible at a total power consumption of 86 mW translating to 21.5 mW/qubit in the presented measurements. Comparison with the state-of-the-art controller reveals drastic power and form-factor reduction at comparable performance, thus paving the way for a scalable TI platform. The chip is fabricated in a 0.13- $\mathrm {\mu }\mathrm {m}$ SiGe BiCMOS technology. To the best of our knowledge, this is the first reported from-scratch system design for TI-based QC concluding with a qubit state manipulation demonstration.
- 8 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 24 (13) , 20794-20804
Pulsed-Heating System With an Integrated Metal-Oxide Sensor Array Scheming Low-Power Temperature Modulation
Sensor integration and low-power operation are required to collect different molecular information. However, it is challenging to integrate different types of sensors onto a single chip. To obtain multiple molecular information, temperature modulation of metal-oxide gas sensors is highly effective since it allows for the variation of sensor molecular sensitivity based on the operating temperature. This paper covers a proposed novel system using metal-oxide gas sensors. The temperatures of the sensors are controlled by adopting self-heated sensors, which achieve local temperature increase and low-power operation. To simultaneously heat multiple sensors, we implemented a printed circuit board (PCB) for pulsed-heating scheme and streamlined intended input power with a proportional-integral-derivative (PID) controller. The performance of the implemented circuit is evaluated, maximum error rate of 1.7 % of heating accuracy and 0.68 % of average readout accuracy is ensured. As a proof-of-concept of the proposed gas sensory system, an array of 16 self-heated sensors was fabricated on a chip and tested with reactive gas molecules. The PID controller set the input power in 8 ms and kept constant power while sensor resistance changed. The proposed pulsed-heating measurement and conventional continuous-heating measurement were experimentally compared. The results of the experimental comparison suggest that while the sensitivity of the proposed pulsed-heating measurement decreases slightly, the power consumption due to heating can be reduced by up to 1/16.
- 8 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 24 (13) , 20794-20804
Pulsed-Heating System With an Integrated Metal-Oxide Sensor Array Scheming Low-Power Temperature Modulation
Sensor integration and low-power operation are required to collect different molecular information. However, it is challenging to integrate different types of sensors onto a single chip. To obtain multiple molecular information, temperature modulation of metal-oxide gas sensors is highly effective since it allows for the variation of sensor molecular sensitivity based on the operating temperature. This paper covers a proposed novel system using metal-oxide gas sensors. The temperatures of the sensors are controlled by adopting self-heated sensors, which achieve local temperature increase and low-power operation. To simultaneously heat multiple sensors, we implemented a printed circuit board (PCB) for pulsed-heating scheme and streamlined intended input power with a proportional-integral-derivative (PID) controller. The performance of the implemented circuit is evaluated, maximum error rate of 1.7 % of heating accuracy and 0.68 % of average readout accuracy is ensured. As a proof-of-concept of the proposed gas sensory system, an array of 16 self-heated sensors was fabricated on a chip and tested with reactive gas molecules. The PID controller set the input power in 8 ms and kept constant power while sensor resistance changed. The proposed pulsed-heating measurement and conventional continuous-heating measurement were experimentally compared. The results of the experimental comparison suggest that while the sensitivity of the proposed pulsed-heating measurement decreases slightly, the power consumption due to heating can be reduced by up to 1/16.
- Open Access
- 6 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 12, 28-33
A 65nm Cryogenic CMOS Design and Performance at 4.2K for Quantum State Controller Application
A performance evaluation of cryogenic CMOS circuit at liquid-helium temperature (4.2K) is conducted using a standard 65nm bulk CMOS for quantum state controller (QSC) applications. The ON-current (Ion) of the core n/pMOSFET are increased by 25% and 9% with excellent gate modulation (Ion/Ioff= 109). The cryogenic characteristics of copper interconnects in the back end of the line (BEOL), including line and via resistances, capacitances, and Joule-heating effect (JHE) are accurately assessed. The interconnect and via resistances decrease with temperature due to a reduction of electron-phonon scattering, resulting in resistances that are 75% and 20% lower at 4.2K compared to those at room temperature (RT). No significant change in inter-line capacitance and no severe JHE are observed in the Cu BEOL at 4K. The developed cell libraries for Simulation Program with Integrated Circuit Emphasis (SPICE) model and the technology file, which includes RC interconnect parameters, enable precise design of CMOS circuits at 4.2K. This results in a demonstrated +18.3% increase in speed or -16% reduction in power consumption for ring-oscillator (ROSC) at 4.2K, aligning well with the simulation results obtained from the developed model.
- 6 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 12, 28-33
Open AccessA 65nm Cryogenic CMOS Design and Performance at 4.2K for Quantum State Controller Application
A performance evaluation of cryogenic CMOS circuit at liquid-helium temperature (4.2K) is conducted using a standard 65nm bulk CMOS for quantum state controller (QSC) applications. The ON-current (Ion) of the core n/pMOSFET are increased by 25% and 9% with excellent gate modulation (Ion/Ioff= 109). The cryogenic characteristics of copper interconnects in the back end of the line (BEOL), including line and via resistances, capacitances, and Joule-heating effect (JHE) are accurately assessed. The interconnect and via resistances decrease with temperature due to a reduction of electron-phonon scattering, resulting in resistances that are 75% and 20% lower at 4.2K compared to those at room temperature (RT). No significant change in inter-line capacitance and no severe JHE are observed in the Cu BEOL at 4K. The developed cell libraries for Simulation Program with Integrated Circuit Emphasis (SPICE) model and the technology file, which includes RC interconnect parameters, enable precise design of CMOS circuits at 4.2K. This results in a demonstrated +18.3% increase in speed or -16% reduction in power consumption for ring-oscillator (ROSC) at 4.2K, aligning well with the simulation results obtained from the developed model.
- 16 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 59 (6) , 1823-1834
Design of Dual Lower Bound Hysteresis Control in Switched-Capacitor DC–DC Converter for Optimum Efficiency and Transient Speed in Wide Loading Range for IoT Application
This article proposes a dual lower bound hysteresis control (LBHC) method with frequency control for the design of switched-capacitor (SC) dc–dc converters in always-on Internet-of-Things (IoT) applications. Conventional SC control methods often face a tradeoff between speed and efficiency. Efficiency is crucial for battery life, while speed is essential for system responsiveness. This article aims to use the proposed method to achieve frequency-independent regulation of the output dc level. This helps achieve a fast response time at the system level by tuning controller frequencies without compromising stability. Furthermore, the proposed dual LBHC loop guides frequency and power scaling, ensuring consistent efficiency over a wide range of load currents through two clock-gated comparator operations per clock cycle. By analyzing the operating principle, this article also discovered that designing the dual LBHC based on its maximum load current point can guarantee its stability over the entire load range. To illustrate this concept, a fully integrated 2:1 capacitive dc–dc converter was implemented using a 180-nm CMOS process. The results demonstrate guaranteed efficiency of at least 75% across load current ranges up to 228 $\times$ , with a peak efficiency of 80.4%. In addition, an active response time of 80 ns is achieved during load transients ranging from 0.04 to 4 mA.
- 16 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 59 (6) , 1823-1834
Design of Dual Lower Bound Hysteresis Control in Switched-Capacitor DC–DC Converter for Optimum Efficiency and Transient Speed in Wide Loading Range for IoT Application
This article proposes a dual lower bound hysteresis control (LBHC) method with frequency control for the design of switched-capacitor (SC) dc–dc converters in always-on Internet-of-Things (IoT) applications. Conventional SC control methods often face a tradeoff between speed and efficiency. Efficiency is crucial for battery life, while speed is essential for system responsiveness. This article aims to use the proposed method to achieve frequency-independent regulation of the output dc level. This helps achieve a fast response time at the system level by tuning controller frequencies without compromising stability. Furthermore, the proposed dual LBHC loop guides frequency and power scaling, ensuring consistent efficiency over a wide range of load currents through two clock-gated comparator operations per clock cycle. By analyzing the operating principle, this article also discovered that designing the dual LBHC based on its maximum load current point can guarantee its stability over the entire load range. To illustrate this concept, a fully integrated 2:1 capacitive dc–dc converter was implemented using a 180-nm CMOS process. The results demonstrate guaranteed efficiency of at least 75% across load current ranges up to 228 $\times$ , with a peak efficiency of 80.4%. In addition, an active response time of 80 ns is achieved during load transients ranging from 0.04 to 4 mA.
- 9 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 59 (3) , 740-752
A 4.6–400 K Functional Ringamp-Based 250 MS/s 12 b Pipelined ADC With PVT-Robust Unity-Gain-Frequency-Aware Bias Calibration
This article presents a process voltage temperature (PVT) -robust ring amplifier that enables a high speed pipelined analog-to-digital-converter (ADC) without gain calibration, operating across a temperature range of 4.6–400 K. To ensure the stability of the ringamp, given the large variation of MOSFET transconductance, threshold voltage, and drain resistance across temperature, we propose a unity-gain-frequency-aware bias calibration and a 1st-stage bias-enhancement technique. The unity-gain-frequency-aware bias calibration stabilizes the amplifier bandwidth by biasing the 3rd stage of the ringamp using a constant- $Gm$ circuit and then optimizing the overall phase margin by tuning the 1st and 2nd stages based on feedback from an amplifier output settling monitor. An additional bias-enhancement technique alleviates the issue of insufficient voltage headroom at cryogenic temperatures (CTs) in the fully differential first stage of the ringamp. This is achieved by separately ac-coupling the NMOS and PMOS of the 1st-stage inverter. Furthermore, to deal with insufficient gain in advanced CMOS process, a cascode correlated-level-shifting (CLS) technique is proposed. This enables gain-calibration-free operation while achieving higher speed than conventional CLS. A 12-bit 250 MS/s pipelined ADC prototype is fabricated with the proposed ringamp in 65 nm CMOS technology. It achieves a signal to noise and distortion ratio (SNDR) above 57.7 dB across the 4.6–400 K temperature range, and Walden figure-of-merit (FoM) of 154 fJ/conv.-step at 4.6 K while operating without any gain calibrations. To the best of our knowledge, the achieved functional temperature range is the widest ever reported for a pipelined ADC.
- 9 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 59 (3) , 740-752
A 4.6–400 K Functional Ringamp-Based 250 MS/s 12 b Pipelined ADC With PVT-Robust Unity-Gain-Frequency-Aware Bias Calibration
This article presents a process voltage temperature (PVT) -robust ring amplifier that enables a high speed pipelined analog-to-digital-converter (ADC) without gain calibration, operating across a temperature range of 4.6–400 K. To ensure the stability of the ringamp, given the large variation of MOSFET transconductance, threshold voltage, and drain resistance across temperature, we propose a unity-gain-frequency-aware bias calibration and a 1st-stage bias-enhancement technique. The unity-gain-frequency-aware bias calibration stabilizes the amplifier bandwidth by biasing the 3rd stage of the ringamp using a constant- $Gm$ circuit and then optimizing the overall phase margin by tuning the 1st and 2nd stages based on feedback from an amplifier output settling monitor. An additional bias-enhancement technique alleviates the issue of insufficient voltage headroom at cryogenic temperatures (CTs) in the fully differential first stage of the ringamp. This is achieved by separately ac-coupling the NMOS and PMOS of the 1st-stage inverter. Furthermore, to deal with insufficient gain in advanced CMOS process, a cascode correlated-level-shifting (CLS) technique is proposed. This enables gain-calibration-free operation while achieving higher speed than conventional CLS. A 12-bit 250 MS/s pipelined ADC prototype is fabricated with the proposed ringamp in 65 nm CMOS technology. It achieves a signal to noise and distortion ratio (SNDR) above 57.7 dB across the 4.6–400 K temperature range, and Walden figure-of-merit (FoM) of 154 fJ/conv.-step at 4.6 K while operating without any gain calibrations. To the best of our knowledge, the achieved functional temperature range is the widest ever reported for a pipelined ADC.
- 6 September 2023
- Published by Japan Society of Applied Physics
Gate-Length Dependent Variability of nMOSFET at Cryogenic Temperatures
2023 International Conference on Solid State Devices and Materials ,Gate-Length Dependent Variability of nMOSFET at Cryogenic Temperatures
- 6 September 2023
- Published by Japan Society of Applied Physics
Gate-Length Dependent Variability of nMOSFET at Cryogenic Temperatures
2023 International Conference on Solid State Devices and Materials ,Gate-Length Dependent Variability of nMOSFET at Cryogenic Temperatures
- 28 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 70 (10) , 3877-3881
A Cryogenic 12 GHz Frequency Doubler With Temperature Compensation for Trapped-Ion Quantum Computer
This work presents a frequency doubler (FD) for a microwave-control system intended for an 171Yb+ ion-trap-based quantum computer. The circuit is optimized for frequency multiplication from 11 GHz to 13 GHz with a ≥ 29 dBc fundamental-and third harmonic rejection over the entire frequency range and peak HRR1/HRR3 of 37 dBc/39 dBc. This enables the microwave frequency generation to drive the hyperfine transitions in the electronic ground state of an 171Yb+ ion at 12.6 GHz. Cryogenic measurements of the FD down to 4.5K enable circuit functionality verification for the intended low-temperature operation. Additionally, insights into the cryogenic temperature effects of the employed BiCMOS technology are obtained and used to derive a biasing control methodology for constant performance in the temperature range of 300K to 4.5 K. The proposed circuit is silicon-proven and fabricated in a 0.13μm SiGe BiCMOS process, consuming a core area of only 0.034mm2.
- 28 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 70 (10) , 3877-3881
A Cryogenic 12 GHz Frequency Doubler With Temperature Compensation for Trapped-Ion Quantum Computer
This work presents a frequency doubler (FD) for a microwave-control system intended for an 171Yb+ ion-trap-based quantum computer. The circuit is optimized for frequency multiplication from 11 GHz to 13 GHz with a ≥ 29 dBc fundamental-and third harmonic rejection over the entire frequency range and peak HRR1/HRR3 of 37 dBc/39 dBc. This enables the microwave frequency generation to drive the hyperfine transitions in the electronic ground state of an 171Yb+ ion at 12.6 GHz. Cryogenic measurements of the FD down to 4.5K enable circuit functionality verification for the intended low-temperature operation. Additionally, insights into the cryogenic temperature effects of the employed BiCMOS technology are obtained and used to derive a biasing control methodology for constant performance in the temperature range of 300K to 4.5 K. The proposed circuit is silicon-proven and fabricated in a 0.13μm SiGe BiCMOS process, consuming a core area of only 0.034mm2.
- 11 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 23 (11) , 11746-11753
Accurate Sneak-Path-Controlled Readout for a Cross-Point Resistive Sensor Array
A readout method of measuring resistances from a sensor array is proposed. As opposed to the conventional method of feedback readout, in which the crosstalk is suppressed by an op-amp, the sneak paths are controlled by switches, and a matrix equation of the circuit is derived from measured voltage. Thus, the scanning speed and power consumption of an interface circuit are not inherently deteriorated by the op-amp. The main factors affecting readout accuracy are parasitic resistance of the analog switch and quantized error of the analog-to-digital converters (ADCs). Therefore, calibration of switch resistance is also proposed to maintain readout accuracy by additional ADCs. To evaluate the proposed readout system, “sneak-path-controlled readout” (SPCR) and “accurate sneak-path-controlled readout” (ASPCR) are implemented. To verify the accuracy of the proposed readout method, the interface circuit and the calibration of switch resistance were simulated by MATLAB. The target array size was 32×32, and the sensor resistances were distributed in the same manner as real sensors. Since readout performance is also affected by the pattern of resistances, several patterns of resistance were prepared, and their results were compared. The results of the simulations show that SPCR using a 16-bit ADC can read normally distributed sensors with readout error of 0.05%. Moreover, ASPCR can handle a wider resistance distribution, and its readout error was less than 0.3% with a resistance pattern in which resistance ranges from 1.71 kΩ to 217 kΩ.
- 11 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 23 (11) , 11746-11753
Accurate Sneak-Path-Controlled Readout for a Cross-Point Resistive Sensor Array
A readout method of measuring resistances from a sensor array is proposed. As opposed to the conventional method of feedback readout, in which the crosstalk is suppressed by an op-amp, the sneak paths are controlled by switches, and a matrix equation of the circuit is derived from measured voltage. Thus, the scanning speed and power consumption of an interface circuit are not inherently deteriorated by the op-amp. The main factors affecting readout accuracy are parasitic resistance of the analog switch and quantized error of the analog-to-digital converters (ADCs). Therefore, calibration of switch resistance is also proposed to maintain readout accuracy by additional ADCs. To evaluate the proposed readout system, “sneak-path-controlled readout” (SPCR) and “accurate sneak-path-controlled readout” (ASPCR) are implemented. To verify the accuracy of the proposed readout method, the interface circuit and the calibration of switch resistance were simulated by MATLAB. The target array size was 32×32, and the sensor resistances were distributed in the same manner as real sensors. Since readout performance is also affected by the pattern of resistances, several patterns of resistance were prepared, and their results were compared. The results of the simulations show that SPCR using a 16-bit ADC can read normally distributed sensors with readout error of 0.05%. Moreover, ASPCR can handle a wider resistance distribution, and its readout error was less than 0.3% with a resistance pattern in which resistance ranges from 1.71 kΩ to 217 kΩ.