VKVladimir A. Khrustalev

Vladimir A. Khrustalev

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Vladimir A. Khrustalev has a total of 9 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    The reduced size quasi-Yagi antenna with an ends-fed dipole-like driver

    by Victor Atuchin, Dmitriy Buhtiyarov, Anatoly Gorbachev, Vladimir Khrustalev, Natalya Tarasenko

    A modified version of the printed quasi-Yagi antenna by using the so-called ends-fed dipole-like radiator is presented. In this radiator, the excitation nodes are placed on the far ends of the dipole metallic halves rather than on the adjacent ones. As a result, the current distribution along each of the radiator cylindrical/printed wire significantly differs from that related to the ordinary center-fed dipole. That is why the frequency behavior of the proposed radiator input impedance guarantees the nontraditional radiation properties. Additionally, this approach to the choice of the excitation nodes leads to the simplification of the printed-circuit-board (PCB) implementation. A printed prototype operating at 2.8 GHz is developed and tested. Since the area around the radiating arms is fully free from any conductors and dielectrics (except for the substrate itself), the proposed quasi-Yagi antenna is a good candidate to emit radiation of high polarization purity. The measured results revealed that such an antenna is able to reach an effective area reduction to 40% with the enhanced up to 10 dB front-to-back ratio without decreasing the bandwidth. Keywords: Printed-circuit-board radiators, induced electromotive force method, quasi-Yagi antenna, radiation pattern, telecommunication.

  • High frequency signal adder

    by Ilya V. Vershenya, Vladimir P. Razinkin, Vladimir A. Khrustalev, Alexander S. Mitkov, Novosibirsk Llc «Alfa-Instruments», Pavel G. Bogomolov

    The paper presents the results of the development and investigation of the frequency properties of a wide-band adder of high-power high-frequency signals. The adder is intended for the construction of multichannel RF and microwave amplifiers used in transmitting de-vices of radio engineering systems, telecommunications, communica-tion systems, digital terrestrial television broadcasting, electronic war-fare equipment, as an equivalent antenna, as well as in medical equipment. This paper presents a two-input adder based on three co-axial or microstrip transmission line segments with the same 50 ohm impedance. At the same time, all three segments have a length of less than a quarter of the wavelength, which significantly reduces the weight and size indicators. The use of coaxial or microstrip transmis-sion line segments with a wave resistance of 50 ohms to build the adder ensures the operation of the adder at an input power level of several kW and significantly simplifies the design. By introducing shortening capacitors into each segment of the transmission line, the effect of the parasitic capacitance of a powerful film-type ballast re-sistor is neutralized and high-quality matching in the frequency band of up to 15% is achieved. Based on the considered adder, high-power multi-input summing microwave systems can be implemented.

  • Methods of increasing the input power level in multi-element film microwave attenuators

    by Alexsandr S. Mitkov, Vladimir P. Razinkin, Vladimir A. Khrustalev

    The paper describes the design principles of multi-element broadband microwave attenuators of a high power level on film resistors. The proposed approaches make it possible to increase the input power level by several times or, at a constant input power, to significantly expand the ope¬rating frequency band. The studied attenuators with an insertion loss of 1-10 dB provide high-quality matching in the 0-2 GHz frequency band at an input power level of up to 500 W. These parameters are obtained by introducing quarter-wave sections of transmission lines with a certain wave imped-ance into the longitudinal and transverse branches of matched U-shaped and T-shaped dissipative structures.