Anatoly Gorbachev
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Anatoly Gorbachev has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Dmitriy A. Buhtiyarov
Department of Radio Engineering and Electronics, Novosibirsk State Technical University, Novosibirsk 630073, Russia
1 shared publication - Natalya Tarasenko
Novosibirsk State Technical University, Novosibirsk, Russia
1 shared publication - Sergey A. Alekseytsev
Novosibirsk State Technical University
1 shared publication - Victor V. Atuchin
Research and Development Department, Kemerovo State University, Kemerovo 650000, Russia
1 shared publication - Vladimir A. Khrustalev
Novosibirsk State Technical University, Novosibirsk, Russia
1 shared publication - Yu. N. Parshin
Novosibirsk State Technical University
1 shared publication
Latest Publications
- Open Access
- 19 June 2026
- Published by al-Farabi Kazakh National University in Physical Sciences and Technology
- Vol. 13 (1-2) , 78-93
The reduced size quasi-Yagi antenna with an ends-fed dipole-like driver
A modified version of the printed quasi-Yagi antenna by using the so-called ends-fed dipole-like radiator is presented. In this radiator, the excitation nodes are placed on the far ends of the dipole metallic halves rather than on the adjacent ones. As a result, the current distribution along each of the radiator cylindrical/printed wire significantly differs from that related to the ordinary center-fed dipole. That is why the frequency behavior of the proposed radiator input impedance guarantees the nontraditional radiation properties. Additionally, this approach to the choice of the excitation nodes leads to the simplification of the printed-circuit-board (PCB) implementation. A printed prototype operating at 2.8 GHz is developed and tested. Since the area around the radiating arms is fully free from any conductors and dielectrics (except for the substrate itself), the proposed quasi-Yagi antenna is a good candidate to emit radiation of high polarization purity. The measured results revealed that such an antenna is able to reach an effective area reduction to 40% with the enhanced up to 10 dB front-to-back ratio without decreasing the bandwidth. Keywords: Printed-circuit-board radiators, induced electromotive force method, quasi-Yagi antenna, radiation pattern, telecommunication.
- 19 June 2026
- Published by al-Farabi Kazakh National University in Physical Sciences and Technology
- Vol. 13 (1-2) , 78-93
Open AccessThe reduced size quasi-Yagi antenna with an ends-fed dipole-like driver
A modified version of the printed quasi-Yagi antenna by using the so-called ends-fed dipole-like radiator is presented. In this radiator, the excitation nodes are placed on the far ends of the dipole metallic halves rather than on the adjacent ones. As a result, the current distribution along each of the radiator cylindrical/printed wire significantly differs from that related to the ordinary center-fed dipole. That is why the frequency behavior of the proposed radiator input impedance guarantees the nontraditional radiation properties. Additionally, this approach to the choice of the excitation nodes leads to the simplification of the printed-circuit-board (PCB) implementation. A printed prototype operating at 2.8 GHz is developed and tested. Since the area around the radiating arms is fully free from any conductors and dielectrics (except for the substrate itself), the proposed quasi-Yagi antenna is a good candidate to emit radiation of high polarization purity. The measured results revealed that such an antenna is able to reach an effective area reduction to 40% with the enhanced up to 10 dB front-to-back ratio without decreasing the bandwidth. Keywords: Printed-circuit-board radiators, induced electromotive force method, quasi-Yagi antenna, radiation pattern, telecommunication.
- Open Access
- 10 March 2026
- Published by St. Petersburg Electrotechnical University LETI in Journal of the Russian Universities. Radioelectronics
- Vol. 29 (1) , 30-39
Printed Butler Matrix Based Eight-Beam Phased Array with Modified Phasers and End-Fed Dipole-Like Radiators
Introduction . This paper presents comparative results of electrodynamic modeling and field measurements in an anechoic chamber of a prototype of a printed eight-beam phased antenna array based on the Butler matrix. A mathematical model of a modified differential phase shifter protected by a patent of the Russian Federation and characterized by the highest broadband to date is presented. The topology of an innovative dipole-type radiator with end feeding is proposed and characterized. Aim. To design an eight-beam antenna array based on a systems approach, to model its main electrodynamic characteristics, and to compare them with the results of full-scale experiments. Materials and methods. Electrodynamic models of elements and units of the diagram-forming circuit, as well as the emitter, were designed using the method of induced electromotive forces, mathematical foundations of designing microstrip-technologies, procedures for electrodynamic modeling of elements and units of microwave technology and microwave devices. The FAF-4D domestic dielectric material with a relative permittivity of 2.5 was used. Results . The characteristics of the matching and directivity of the eight-beam antenna array were obtained followed by their comparison with the results of full-wave electrodynamic modeling. As a result, in the frequency band of 2.02…2.37 GHz, an acceptable coincidence of the measured and modeled results is observed for the positions of the beams, cross-polarization intensities, reflection coefficients, and decoupling between the Butler matrix inputs of no worse than 15 dB. Conclusion . The design and final refinement of phased antenna arrays with improved electrodynamic characteristics, taking domestic design and technological standards into account, will form a basis for a qualitative increase in the tactical and technical performance of transceiver devices as a whole, allowing procedures for synthesizing such arrays and their individual units to be developed.
- 10 March 2026
- Published by St. Petersburg Electrotechnical University LETI in Journal of the Russian Universities. Radioelectronics
- Vol. 29 (1) , 30-39
Open AccessPrinted Butler Matrix Based Eight-Beam Phased Array with Modified Phasers and End-Fed Dipole-Like Radiators
Introduction . This paper presents comparative results of electrodynamic modeling and field measurements in an anechoic chamber of a prototype of a printed eight-beam phased antenna array based on the Butler matrix. A mathematical model of a modified differential phase shifter protected by a patent of the Russian Federation and characterized by the highest broadband to date is presented. The topology of an innovative dipole-type radiator with end feeding is proposed and characterized. Aim. To design an eight-beam antenna array based on a systems approach, to model its main electrodynamic characteristics, and to compare them with the results of full-scale experiments. Materials and methods. Electrodynamic models of elements and units of the diagram-forming circuit, as well as the emitter, were designed using the method of induced electromotive forces, mathematical foundations of designing microstrip-technologies, procedures for electrodynamic modeling of elements and units of microwave technology and microwave devices. The FAF-4D domestic dielectric material with a relative permittivity of 2.5 was used. Results . The characteristics of the matching and directivity of the eight-beam antenna array were obtained followed by their comparison with the results of full-wave electrodynamic modeling. As a result, in the frequency band of 2.02…2.37 GHz, an acceptable coincidence of the measured and modeled results is observed for the positions of the beams, cross-polarization intensities, reflection coefficients, and decoupling between the Butler matrix inputs of no worse than 15 dB. Conclusion . The design and final refinement of phased antenna arrays with improved electrodynamic characteristics, taking domestic design and technological standards into account, will form a basis for a qualitative increase in the tactical and technical performance of transceiver devices as a whole, allowing procedures for synthesizing such arrays and their individual units to be developed.