Aleksandra Lont
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Aleksandra Lont has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Jacek Górka
Department of Welding Engineering, Silesian University of Technology, Konarskiego Str. 18a, 44-100 Gliwice, Poland
11 shared publications - Tomasz Poloczek
Welding Department, Faculty of Mechanical Engineering, Silesian University of Technology, Konarskiego Street 18A, 44-100 Gliwice, Poland
8 shared publications - Damian Janicki
Welding Department, Faculty of Mechanical Engineering, Silesian University of Technology, Konarskiego Street 18A, 44-100 Gliwice, Poland
5 shared publications - Agnieszka Rzeźnikiewicz
Welding Department, Faculty of Mechanical Engineering, Silesian University of Technology, Konarskiego Street 18A, 44-100 Gliwice, Poland
2 shared publications - Marcin Żuk
Welding Department, Faculty of Mechanical Engineering, Silesian University of Technology, Konarskiego Street 18A, 44-100 Gliwice, Poland
2 shared publications - Ewa Jonda
Department of Engineering Materials and Biomaterials, Faculty of Mechanical Engineering, Silesian University of Technology, Gliwice, Poland
1 shared publication
Latest Publications
- Open Access
The Structure, Microhardness and Solid Particle Erosion Wear Characteristics of the Laser-Cladded Inconel 625 Coatings Reinforced with Cr3C2 Particles on Non-Alloy Steel Substrate
The article presents the results of research concerning the laser cladding process of the Inconel 625 coatings reinforced with Cr3C2 particles. Nickel-based superalloys find widespread application in aggressive corrosive environments because of their many favorable properties, such as high tensile and fatigue strength and excellent resistance to high-temperature corrosion. The current research aimed to improve the surface wear resistance of Inconel 625 coatings by the addition of 20–40 vol.% of Cr3C2 particles. The research focused on determining the impact of the laser beam power and Cr3C2 particle content on the quality, structure and properties (microhardness and solid particle erosion wear resistance) of coatings. The investigation included the macrostructure and microstructure analyses, Energy Dispersive Spectroscopy (EDS), X-Ray Diffraction (XRD), Vickers microhardness and solid particle erosion tests (according to the ASTM G76-18 standard). The main results showed that the homogenous composite Inconel 625 + Cr3C2 coatings can be produced using the laser cladding process to improve the hardness and erosive wear resistance in comparison to pure metallic Inconel 625 coatings.
Open AccessThe Structure, Microhardness and Solid Particle Erosion Wear Characteristics of the Laser-Cladded Inconel 625 Coatings Reinforced with Cr3C2 Particles on Non-Alloy Steel Substrate
The article presents the results of research concerning the laser cladding process of the Inconel 625 coatings reinforced with Cr3C2 particles. Nickel-based superalloys find widespread application in aggressive corrosive environments because of their many favorable properties, such as high tensile and fatigue strength and excellent resistance to high-temperature corrosion. The current research aimed to improve the surface wear resistance of Inconel 625 coatings by the addition of 20–40 vol.% of Cr3C2 particles. The research focused on determining the impact of the laser beam power and Cr3C2 particle content on the quality, structure and properties (microhardness and solid particle erosion wear resistance) of coatings. The investigation included the macrostructure and microstructure analyses, Energy Dispersive Spectroscopy (EDS), X-Ray Diffraction (XRD), Vickers microhardness and solid particle erosion tests (according to the ASTM G76-18 standard). The main results showed that the homogenous composite Inconel 625 + Cr3C2 coatings can be produced using the laser cladding process to improve the hardness and erosive wear resistance in comparison to pure metallic Inconel 625 coatings.
- Open Access
Shaping the Structure and Properties of Stellite 6 Alloy by Addition of Ti and W via Laser Cladding
Cobalt-based alloys such as Stellite 6 are widely applied in demanding conditions because of their good resistance to wear, erosion, and corrosion, but further improvements in erosion resistance are still required. This work analyzes the effect of adding titanium and tungsten on the structure and properties of Stellite 6 coatings produced by laser cladding, aiming to enhance their erosion resistance. Penetrant tests confirmed that the additions did not reduce coating quality, and macroscopic observations showed that appropriate process parameters allowed for defect-free coatings with strong bonding to the substrate. Microstructural studies carried out by SEM/EDS (Scanning Electron Microscopy/ Energy Dispersive Spectroscopy) and XRD (X-ray Diffraction) revealed that the reference Stellite 6 coating consisted of a cobalt-based austenitic matrix with interdendritic chromium carbides, while Ti and W additions led to the in situ formation of primary and eutectic (Ti,W)C carbides. Transmission electron microscopy showed a gradient in tungsten concentration inside the primary carbides, with progressive tungsten dissolution into the TiC lattice. Although different powder compositions had only a moderate effect on hardness, erosion tests demonstrated that the coatings with Ti and W exhibited clearly improved resistance. In particular, the in situ carbides enhanced erosion resistance at 30° impingement angles, while also maintaining high resistance under 90° impact. These findings confirm that modifying Stellite 6 with Ti and W during laser cladding is an effective way to improve its durability in erosive conditions.
Open AccessShaping the Structure and Properties of Stellite 6 Alloy by Addition of Ti and W via Laser Cladding
Cobalt-based alloys such as Stellite 6 are widely applied in demanding conditions because of their good resistance to wear, erosion, and corrosion, but further improvements in erosion resistance are still required. This work analyzes the effect of adding titanium and tungsten on the structure and properties of Stellite 6 coatings produced by laser cladding, aiming to enhance their erosion resistance. Penetrant tests confirmed that the additions did not reduce coating quality, and macroscopic observations showed that appropriate process parameters allowed for defect-free coatings with strong bonding to the substrate. Microstructural studies carried out by SEM/EDS (Scanning Electron Microscopy/ Energy Dispersive Spectroscopy) and XRD (X-ray Diffraction) revealed that the reference Stellite 6 coating consisted of a cobalt-based austenitic matrix with interdendritic chromium carbides, while Ti and W additions led to the in situ formation of primary and eutectic (Ti,W)C carbides. Transmission electron microscopy showed a gradient in tungsten concentration inside the primary carbides, with progressive tungsten dissolution into the TiC lattice. Although different powder compositions had only a moderate effect on hardness, erosion tests demonstrated that the coatings with Ti and W exhibited clearly improved resistance. In particular, the in situ carbides enhanced erosion resistance at 30° impingement angles, while also maintaining high resistance under 90° impact. These findings confirm that modifying Stellite 6 with Ti and W during laser cladding is an effective way to improve its durability in erosive conditions.
- Open Access
The Microstructure and Properties of Laser-Cladded Ni-Based Self-Fluxing Alloy Coatings Reinforced by TiC Particles
In this study, NiCrBSi composite coatings reinforced with 5–15 wt.% TiC particles were prepared using laser cladding to investigate the influence of the TiC content and laser beam power on the coatings’ quality, structure, and properties. Penetrant tests revealed the presence of cracks in the composite coatings, which were reduced with the higher laser power due to a decrease in cooling rate. A macroscopic analysis showed that pure NiCrBSi coatings exhibited a high quality and were free of defects, while the addition of TiC particles led to the formation of large pores, particularly in coatings produced with a lower laser power. Microstructural characterization was conducted using Scanning Electron Microscopy (SEM), Energy-Dispersive Spectroscopy (EDS), and X-ray Diffraction (XRD). The microstructure of the pure NiCrBSi coatings consisted of an austenitic matrix with chromium-based precipitates (carbides and borides). Variations in structural morphology across different regions of the coatings and under varying laser powers were described. When TiC particles were added, partial dissolution occurred in the molten pool, enriching it with titanium and carbon, which subsequently led to the precipitation of titanium carbides. The average microhardness of the composite coatings increased by 28%–40% compared to the pure NiCrBSi coating, while the erosion resistance remained comparable. Solid particle erosion tests in accordance with the ASTM G76-18 standard resulted in average erosion values of the pure NiCrBSi coating of 0.0056 and 0.0025 mm3/g for the 30° and 90° impingement angles, respectively.
Open AccessThe Microstructure and Properties of Laser-Cladded Ni-Based Self-Fluxing Alloy Coatings Reinforced by TiC Particles
In this study, NiCrBSi composite coatings reinforced with 5–15 wt.% TiC particles were prepared using laser cladding to investigate the influence of the TiC content and laser beam power on the coatings’ quality, structure, and properties. Penetrant tests revealed the presence of cracks in the composite coatings, which were reduced with the higher laser power due to a decrease in cooling rate. A macroscopic analysis showed that pure NiCrBSi coatings exhibited a high quality and were free of defects, while the addition of TiC particles led to the formation of large pores, particularly in coatings produced with a lower laser power. Microstructural characterization was conducted using Scanning Electron Microscopy (SEM), Energy-Dispersive Spectroscopy (EDS), and X-ray Diffraction (XRD). The microstructure of the pure NiCrBSi coatings consisted of an austenitic matrix with chromium-based precipitates (carbides and borides). Variations in structural morphology across different regions of the coatings and under varying laser powers were described. When TiC particles were added, partial dissolution occurred in the molten pool, enriching it with titanium and carbon, which subsequently led to the precipitation of titanium carbides. The average microhardness of the composite coatings increased by 28%–40% compared to the pure NiCrBSi coating, while the erosion resistance remained comparable. Solid particle erosion tests in accordance with the ASTM G76-18 standard resulted in average erosion values of the pure NiCrBSi coating of 0.0056 and 0.0025 mm3/g for the 30° and 90° impingement angles, respectively.
- Open Access
Microstructure and Erosion Wear of In Situ TiC-Reinforced Co-Cr-W-C (Stellite 6) Laser-Cladded Coatings
The article presents research results on the possibility of shaping the structure and properties of Co-Cr-W-C-Ti alloys (type Stellite 6) using laser cladding technology. Cobalt-based alloys are used in several industries because they are characterized by high erosion, abrasion, and corrosion resistance, retaining these properties at high temperatures. To further increase erosion resistance, it seems appropriate to reinforce material by in situ synthesis of hard phases. Among the transition metal carbides (TMCs), titanium carbide is one of the hardest and can have a positive effect on the extension of the lifetime of components made from cobalt-based alloys. In this article, concentration of C, W, and Ti due to the possibility of in situ synthesis of titanium carbides was subjected to detailed analysis. The provided research includes macrostructure and microstructure analysis, X-ray diffraction (XRD), microhardness, and penetrant tests. It was found that the optimal concentrations of Ti and C in the Co-Cr-W-C alloy allow the formation of titanium carbides, which significantly improves erosion resistance for low impact angles. Depending on the concentrations of titanium, carbon, and tungsten in the molten metal pool, it is possible to shape the alloy structure by influencing to morphology and size of the reinforcing phase in the form of the complex carbide (Ti,W)C.
Open AccessMicrostructure and Erosion Wear of In Situ TiC-Reinforced Co-Cr-W-C (Stellite 6) Laser-Cladded Coatings
The article presents research results on the possibility of shaping the structure and properties of Co-Cr-W-C-Ti alloys (type Stellite 6) using laser cladding technology. Cobalt-based alloys are used in several industries because they are characterized by high erosion, abrasion, and corrosion resistance, retaining these properties at high temperatures. To further increase erosion resistance, it seems appropriate to reinforce material by in situ synthesis of hard phases. Among the transition metal carbides (TMCs), titanium carbide is one of the hardest and can have a positive effect on the extension of the lifetime of components made from cobalt-based alloys. In this article, concentration of C, W, and Ti due to the possibility of in situ synthesis of titanium carbides was subjected to detailed analysis. The provided research includes macrostructure and microstructure analysis, X-ray diffraction (XRD), microhardness, and penetrant tests. It was found that the optimal concentrations of Ti and C in the Co-Cr-W-C alloy allow the formation of titanium carbides, which significantly improves erosion resistance for low impact angles. Depending on the concentrations of titanium, carbon, and tungsten in the molten metal pool, it is possible to shape the alloy structure by influencing to morphology and size of the reinforcing phase in the form of the complex carbide (Ti,W)C.
- Open Access
Comparison of the Erosive Wear Resistance of Ductile Cast Iron Following Laser Surface Melting and Alloying
This article presents research results on the influence of the laser surface melting and alloying processes on the erosive wear resistance of ductile cast iron. For the research, an EN-GJS 350-22 ductile cast iron surface was laser-melted and laser-alloyed with titanium powder in an argon and nitrogen atmosphere. Solid-particle erosion tests were carried out on the laser-melted and -alloyed surface layers and the base material according to the ASTM G76-04 standard with 30° and 90° impingement angles. The erosive wear resistance results were correlated with Vickers hardness and microstructural test results with the use of SEM (scanning electron microscopy), TEM (transmission electron microscopy), EDS (energy dispersive spectroscopy), and XRD (X-ray diffraction). The mechanisms of erosive wear were also analyzed for the laser-treated surface layers and the base material. The research showed that the laser melting and alloying processes with titanium powder had a positive effect on the hardness and erosive wear resistance of the ductile cast iron surface due to microstructure modification. Moreover, despite the lower hardness of the laser-alloyed surface layers, their composite microstructure had a positive impact on the erosive wear resistance in comparison to the laser-melted surface layers.
Open AccessComparison of the Erosive Wear Resistance of Ductile Cast Iron Following Laser Surface Melting and Alloying
This article presents research results on the influence of the laser surface melting and alloying processes on the erosive wear resistance of ductile cast iron. For the research, an EN-GJS 350-22 ductile cast iron surface was laser-melted and laser-alloyed with titanium powder in an argon and nitrogen atmosphere. Solid-particle erosion tests were carried out on the laser-melted and -alloyed surface layers and the base material according to the ASTM G76-04 standard with 30° and 90° impingement angles. The erosive wear resistance results were correlated with Vickers hardness and microstructural test results with the use of SEM (scanning electron microscopy), TEM (transmission electron microscopy), EDS (energy dispersive spectroscopy), and XRD (X-ray diffraction). The mechanisms of erosive wear were also analyzed for the laser-treated surface layers and the base material. The research showed that the laser melting and alloying processes with titanium powder had a positive effect on the hardness and erosive wear resistance of the ductile cast iron surface due to microstructure modification. Moreover, despite the lower hardness of the laser-alloyed surface layers, their composite microstructure had a positive impact on the erosive wear resistance in comparison to the laser-melted surface layers.
- Open Access
- 1 April 2024
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 18 (2) , 115-128
The Effect of HVOF Spray Distance on Solid Particle Erosion Resistance of WC-based Cermets Bonded by Co, Co-Cr and Ni Deposited on Mg-alloy Substrate
Magnesium alloys are very interesting engineering materials because of their high strength-to-density ratio. On the other hand, they are characterized by low hardness as well as low erosion resistance. Because of these reasons, their applications in the industry are very limited. The article...
- 1 April 2024
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 18 (2) , 115-128
Open AccessThe Effect of HVOF Spray Distance on Solid Particle Erosion Resistance of WC-based Cermets Bonded by Co, Co-Cr and Ni Deposited on Mg-alloy Substrate
Magnesium alloys are very interesting engineering materials because of their high strength-to-density ratio. On the other hand, they are characterized by low hardness as well as low erosion resistance. Because of these reasons, their applications in the industry are very limited. The article...
- Open Access
The Structure and Properties of Laser-Cladded Inconel 625/TiC Composite Coatings
This article presents production results concerning metal matrix composite-coatings made using the laser-cladding technology. The enhancement of the wear resistance of the material surface is the one of the main goals accompanying the manufacturing of composite coatings. Nickel-based superalloys are used in several industries because they are characterized by a number of desirable properties including high tensile and fatigue strength as well as resistance to high-temperature corrosion in aggressive environments. One of the most interesting materials from the group of superalloys is Inconel 625, used as a matrix material in tests discussed in this article. However, nickel-based superalloys are also characterized by an insufficient wear resistance of the surface, therefore, in relation to the tests discussed in this article, Inconel 625-based composite coatings were reinforced by adding 10%, 20% and 40% of titanium carbide particles. The addition of hard phases, i.e., TiC, WC or SiC particles can have a positive effect on the erosion resistance of cladded specimens. The aim of the experiment was to determine the impact of the titanium carbide content on the structure of the alloy and its resistance to corrosive wear, enabling the extension of the service life of Inconel 625/TiC composite coatings. The investigation included microhardness tests, corrosion resistance analysis, penetrant tests, macrostructure and microstructure analyses and X-ray diffraction (XRD) tests. The TiC particles increased the hardness of the coatings and, in general, had a negative impact on the corrosion resistance of pure Inconel 625 coatings. However, the increased homogeneity of composite coatings translated into the improvement of corrosion resistance.
Open AccessThe Structure and Properties of Laser-Cladded Inconel 625/TiC Composite Coatings
This article presents production results concerning metal matrix composite-coatings made using the laser-cladding technology. The enhancement of the wear resistance of the material surface is the one of the main goals accompanying the manufacturing of composite coatings. Nickel-based superalloys are used in several industries because they are characterized by a number of desirable properties including high tensile and fatigue strength as well as resistance to high-temperature corrosion in aggressive environments. One of the most interesting materials from the group of superalloys is Inconel 625, used as a matrix material in tests discussed in this article. However, nickel-based superalloys are also characterized by an insufficient wear resistance of the surface, therefore, in relation to the tests discussed in this article, Inconel 625-based composite coatings were reinforced by adding 10%, 20% and 40% of titanium carbide particles. The addition of hard phases, i.e., TiC, WC or SiC particles can have a positive effect on the erosion resistance of cladded specimens. The aim of the experiment was to determine the impact of the titanium carbide content on the structure of the alloy and its resistance to corrosive wear, enabling the extension of the service life of Inconel 625/TiC composite coatings. The investigation included microhardness tests, corrosion resistance analysis, penetrant tests, macrostructure and microstructure analyses and X-ray diffraction (XRD) tests. The TiC particles increased the hardness of the coatings and, in general, had a negative impact on the corrosion resistance of pure Inconel 625 coatings. However, the increased homogeneity of composite coatings translated into the improvement of corrosion resistance.
- Open Access
- 1 December 2022
- Published by Walter de Gruyter GmbH in Materials Science-Poland
- Vol. 40 (4) , 91-103
The structure and properties of laser-cladded Inconel 625/TiC composite coatings
The article presents the research in the field of production of metal–matrix composite coatings using laser cladding technology. The general purpose of producing composite coatings is the improvement of wear resistance of the material surface. In this research, Inconel 625 was used as a matrix material. Nickel-based superalloys are used in several industries for unique applications because they possess a number of beneficial properties including high tensile and fatigue strengths and resistance to high-temperature corrosion in aggressive environments. However, for some applications, this alloy shows insufficient wear resistance of the surface; therefore, for the tests, Inconel 625-based composite coatings were produced with the addition of 10 vol.%, 20 vol.%, and 40 vol.% of titanium carbide (TiC) particles as reinforcement. In general, the addition of TiC particles had a positive effect on the erosion resistance of the surface. The aim of the current research was to test the influence of TiC particle reinforcement of Inconel 625 laser-cladded coatings on corrosion resistance of the surface. For the tests, the laser-cladded composite coatings with uniform phase distribution were produced. The proceeded tests included penetrant tests, macrostructure and microstructure analysis, X-ray diffraction (XRD), and microhardness and corrosion resistance tests. The results showed that using laser cladding, TiC-reinforced Inconel 625 uniform composite coatings may be produced. The addition of TiC particles caused microstructure changes in the Inconel 625 matrix and an increase in hardness. The addition of TiC particles had a negative influence on Inconel 625 corrosion resistance, but with the increased composite coating homogeneity, the corrosion resistance improved.
- 1 December 2022
- Published by Walter de Gruyter GmbH in Materials Science-Poland
- Vol. 40 (4) , 91-103
Open AccessThe structure and properties of laser-cladded Inconel 625/TiC composite coatings
The article presents the research in the field of production of metal–matrix composite coatings using laser cladding technology. The general purpose of producing composite coatings is the improvement of wear resistance of the material surface. In this research, Inconel 625 was used as a matrix material. Nickel-based superalloys are used in several industries for unique applications because they possess a number of beneficial properties including high tensile and fatigue strengths and resistance to high-temperature corrosion in aggressive environments. However, for some applications, this alloy shows insufficient wear resistance of the surface; therefore, for the tests, Inconel 625-based composite coatings were produced with the addition of 10 vol.%, 20 vol.%, and 40 vol.% of titanium carbide (TiC) particles as reinforcement. In general, the addition of TiC particles had a positive effect on the erosion resistance of the surface. The aim of the current research was to test the influence of TiC particle reinforcement of Inconel 625 laser-cladded coatings on corrosion resistance of the surface. For the tests, the laser-cladded composite coatings with uniform phase distribution were produced. The proceeded tests included penetrant tests, macrostructure and microstructure analysis, X-ray diffraction (XRD), and microhardness and corrosion resistance tests. The results showed that using laser cladding, TiC-reinforced Inconel 625 uniform composite coatings may be produced. The addition of TiC particles caused microstructure changes in the Inconel 625 matrix and an increase in hardness. The addition of TiC particles had a negative influence on Inconel 625 corrosion resistance, but with the increased composite coating homogeneity, the corrosion resistance improved.
- Open Access
The Laser Alloying Process of Ductile Cast Iron Surface with Titanium Powder in Nitrogen Atmosphere
The article presents the results of the laser alloying process of a ductile cast iron EN-GJS 350-22 surface with titanium powder in nitrogen atmosphere. The aim of this research was to test the influence of nitrogen atmosphere on the structure and properties of the ductile cast iron surface layer produced by a laser alloying process with titanium. The laser alloying process was conducted using a Rofin Sinar DL020 2 kW high-power diode laser (HPDDL) with rectangular focus and uniform power density distribution in the focus axis. The tests of the produced surface layers included macrostructure and microstructure observations, X-ray diffraction (XRD) analysis, energy-dispersive spectroscopy (EDS) on scanning electron microscope (SEM) and transmission electron microscope (TEM), Vickers hardness and solid particle erosion according to ASTM G76-04 standard. As a result of the laser alloying process in nitrogen atmosphere with titanium powder, the in situ metal matrix composite structure reinforced by TiCN particles was formed. The laser alloying process of ductile cast iron caused the increased hardness and erosion resistance of the surface.
Open AccessThe Laser Alloying Process of Ductile Cast Iron Surface with Titanium Powder in Nitrogen Atmosphere
The article presents the results of the laser alloying process of a ductile cast iron EN-GJS 350-22 surface with titanium powder in nitrogen atmosphere. The aim of this research was to test the influence of nitrogen atmosphere on the structure and properties of the ductile cast iron surface layer produced by a laser alloying process with titanium. The laser alloying process was conducted using a Rofin Sinar DL020 2 kW high-power diode laser (HPDDL) with rectangular focus and uniform power density distribution in the focus axis. The tests of the produced surface layers included macrostructure and microstructure observations, X-ray diffraction (XRD) analysis, energy-dispersive spectroscopy (EDS) on scanning electron microscope (SEM) and transmission electron microscope (TEM), Vickers hardness and solid particle erosion according to ASTM G76-04 standard. As a result of the laser alloying process in nitrogen atmosphere with titanium powder, the in situ metal matrix composite structure reinforced by TiCN particles was formed. The laser alloying process of ductile cast iron caused the increased hardness and erosion resistance of the surface.
- Open Access
- 1 October 2021
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 1182 (1) , 012026
Analysis of precipitates in heat treated thermo-mechanically processed steel with a high yield strength
The aim of this study was to analyse the precipitates and determine their impact on the structure of thermomechanically processed high strength S700MC steel. The tested samples were subjected to a heating process at temperatures from 100°C up to 1300°C with a 100°C step. The chemical composition analysis in the micro-areas of the samples, thin-film tests and quantitative measurements of carbonitride precipitates were performed. In order to describe the grain size, a method of calculating the number of grains cut through the measuring line was used. In order to determine the effect of heat treatment on strength and plastic properties, Charpy V-notch, Vickers hardness and static tensile tests were carried out. The study showed that S700MC steel is characterized by a non-equivalent, fine-grained bainitic-ferritic structure. The test showed a significant impact of heat treatment on the strength and plastic properties of S700MC steel.
- 1 October 2021
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 1182 (1) , 012026
Open AccessAnalysis of precipitates in heat treated thermo-mechanically processed steel with a high yield strength
The aim of this study was to analyse the precipitates and determine their impact on the structure of thermomechanically processed high strength S700MC steel. The tested samples were subjected to a heating process at temperatures from 100°C up to 1300°C with a 100°C step. The chemical composition analysis in the micro-areas of the samples, thin-film tests and quantitative measurements of carbonitride precipitates were performed. In order to describe the grain size, a method of calculating the number of grains cut through the measuring line was used. In order to determine the effect of heat treatment on strength and plastic properties, Charpy V-notch, Vickers hardness and static tensile tests were carried out. The study showed that S700MC steel is characterized by a non-equivalent, fine-grained bainitic-ferritic structure. The test showed a significant impact of heat treatment on the strength and plastic properties of S700MC steel.